Construction of Petroleum Outlet at Baratang

Amount

Sub Work: Construction of office building for petrol pump at Baratang . Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade Area of slab over 0.50 sqm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x0.90 mm M.S. laths with 0.90 mm thick top cover

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Bend 87.5° 110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix :

1:3 (1 cement : 3 fine sand)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :

Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

40 mm nominal dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Supplying and filling in plinth with Pulverised/Local sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying hollow cement concrete hollow block walling upto floor five level 200mm thick walling consisting of hollow block of size 400mmX 200mmX200mm of mix 1:3:6 ( 1 cement : 3coarse sand : 6 graded stone aggregrate 10mm nominal size) having a crushing strength of 3.5 N/ Sqm at 28 days as per IS: 2185 (Part-1) laid in cement mortar 1:6 ( 1 cement : 6 coarse sand) upto floor five level.

Providing and laying hollow cement concrete hollow block walling upto floor five level 150mm thick walling consisting of hollow block of size 400mmX 150mmX200mm of mix 1:3:6 ( 1 cement : 3coarse sand : 6 graded stone aggregrate 10mm nominal size) having a crushing strength of 3.5 N/ Sqm at 28 days as per IS: 2185 (Part-1) laid in cement mortar 1:6 ( 1 cement : 6 coarse sand) upto floor five level.

Providing and laying Ceramic anti skid floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and applying wall putty (Interior) of 2mm thick over plastered surface to prepare the surface even and smooth complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps (long nose) , 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing PVC flexible pipe 15mm dia for inlet connection for EWC, Wash basin etc of approved make and as per direction of Engineering-in-charge

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 75 mm outletunplasticised Rigid PVC pipes

Providing and fixing 100 mm stainless steel grating for gully trap.

Providing and fixing unplasticised Rigid PVC pipes having 6.80 kg/cm2 conforming to IS : 13592 Type A, and jointing with required solvent including required earthwork excavation and refilling etc.

100 mm dia.

Providing and fixing bend of required degree with access door, insertion rubber washer, screws etc complete.

100 mm dia unplasticised Rigid PVC materials.

Providing and fixing plain bend of required degree.

100 mm dia unplasticised Rigid PVC materials.

Providing and fixing terminal guard :

100 mm dia unplasticised Rigid PVC materials.

Providing and fixing ball valve (CPVC) of approved quality, High or low pressure, with plastic floats complete :

20mm nominal bore

40mm nominal bore

Constructing solid block walling 400x200x200 mm manhole in CM 1:4 ( 1 cement : 4 coarse sand) RCC top slab with 1:1.5:3 ( 1 cement : 1.5 coarse sand : 6 graded stone agregate 20 mm nominal size derived from natural sources) foundation bed concrete 1:4:8 ( 1 cement : 4 coarse sand derived from natural sources : 8 graged stone aggregate 40 mm nominal size derived from natural sources) inside plastering 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) finished with a floating coat of neat cement complete as per standard design.:

Inside side 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover frame to be not less than 38 kg (weight of cover 23 kg and weigth of frame 15 kg)

Providing cement concrete surface drain in given average size with 100 mm thick bed concrete with 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 150mm thick both side walls with 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) i/c 12 mm cement plaster 1:4 (1 cement :4 coarse sand ) with floating coat of neat cement inside the drain, exposed sides and top of walls i/c earth work in excavation and disposal of surplus earth with in a lead of 50mtr.

15 cm X15 cm surface drain

Sub Work:- Construction of Canopy for POL retail outlet at Baratang. Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade Area of slab over 0.50 sqm

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing bolts including nuts and washers complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Supplying and filling in plinth with Pulverised/Local sand under floors including, watering, ramming consolidating and dressing complete.

Providing and fixing MS sheet of 16 gauge for hoarding board to display of signage as per IOC norms including fixing with self drilling/ self tapping screws or welding where ever required.

Providing and fixing Klippon Galvalume steel profile sheets roofing (Size, Shape and pitch of corrugation as approved by Engineer-in-charge) of bare metal thickness 0.50mm as per ASTM A446 having yield stress of 275mpa, surface shall have hot dip metallic coating of Aluminium Zinc alloy comprising of 55% aluminium, 43.50% Zinc & 1.50% silicon, with 5-7 micron epoxy primer and polyester top coat of 15-18 micron on both sides, total coated thickness (TCT) of 0.58mm. Sheet shall have protective guard film of 25 microns minimum to avoid scratches while transportation and should supplied in single length upto 6 metre or as directed by Engineer-in-charge.

Profile Sheet for roofing

Providing and fixing Klippon Galvalume steel profile sheets roofing (Size, Shape and pitch of corrugation as approved by Engineer-in-charge) of bare metal thickness 0.50mm as per ASTM A446 having yield stress of 275mpa, surface shall have hot dip metallic coating of Aluminium Zinc alloy comprising of 55% aluminium, 43.50% Zinc & 1.50% silicon, with 5-7 micron epoxy primer and polyester top coat of 15-18 micron on both sides, total coated thickness (TCT) of 0.58mm. Sheet shall have protective guard film of 25 microns minimum to avoid scratches while transportation and should supplied in single length upto 6 metre or as directed by Engineer-in-charge.

Gutter (1350 mm over all girth)

Providing and fixing 150F/200F flush panel (Pre-coated steel) false ceiling made of cold rolled steel sheet confirming to IS: 513, having minimum yield stress of 240mpa & minimum tensile stress of 300mpa. Base metal thickness 0.45mm for ceiling panels and 0.55mm for carriers. The sheet shall be hot dip metallic coated with zinc coating (Galvanising) as per IS: 277, coating mass of 120gsm on both side, over which organic coating with modified polyester paint on a continuous coil coating line. Top side of ceiling panels and carrier shall have 15 micron modified polyester paint over 5 micron epoxy primer and bottom side with alkyd back coat over 5 micron primer total coated thickness for panels to be 0.50mm and for carriers 0.60mm. The ceiling panels shall be clipped in to carriers, suspended from steel/trusses/other members with the help of suspension angle of 25X25X0.50mm by means of rigid suspension system meant for exterior. Longitudinal joints of two panels shall be butt jointed with special type of panel splice to be fixed from inner side carrier shall be jointed with carrier splices maintaining a module of 150 mm

Sub Work: Construction Security wall for POL retail outlet at Baratang. Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Supplying and filling in plinth with Pulverised/Local sand under floors including, watering, ramming consolidating and dressing complete.

Sub Work: Terracing of site of size 40X35 mtr for POL retail outlet at Baratang. Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

Beyond 60 cm girth upto and including 120 cm girth

Earth work in excavation for terrace formation in all kinds of soil with hydraulic excavator of 0.70 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting surplus earth to the desired location within all lifts and lead upto 5 km.

Sub Work:- Construction of RCC Retaining wall 4.00 mtr height for a length of 35.00mtr for POL retail outlet at Baratang Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Supplying and filling in plinth with Pulverised/Local sand under floors including, watering, ramming consolidating and dressing complete.

Providing and fixing 50mm dia PVC pipe for weep holes in CC/RCC works as per direction of Engineer-in-charge.

Providing and laying stone aggregate of size 90mm to 45mm as a filter media in CC/RCC works as per direction of Engineer-in-charge.

Sub Work: C/o Drive way, internal & external drain, entry & exit approach for POL retail outlet at Baratang Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and fixing 50mm dia PVC pipe for weep holes in CC/RCC works as per direction of Engineer-in-charge.

Sub Work:- Providing IEI & EEI, Air Conditioner for Petroleum Retail outlet at Baratang. Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. Group - 'C'.

Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit alongwith 1 No 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/sub main wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 sq.mm + 1x1.5 sq.mm earth wire.

4 X 6 sq. mm +2 X 6 sq. mm earth wire

4 x 10 sq.mm + 2 x 6 sq.mm earth wire

Supplying and fixing following Piano type switch/socket on the existing Switch box/Cover including connections but excluding modular plate etc as required.

5/6 amps switch.

3 pin 5/6 amps socket.

Telephone Socket Outlet

TV antenna Socket outlet

Supplying and fixing PVC batten/angle holder including connections etc as required

Installation, testing and commissioning of ceiling fan / wall mounting, i/c wiring the down rods of standard length (upto 30cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc as required.

Installation of exhuast fan in the existing opening, including making good the damage, connection, testing, commisioning etc as required

upto 450 mm sweep

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/recessed steel/PVC conduit as required - 02 pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC shetahed in the existing surface/recessed steel/PVC conduit as required

Supplying and fixing cable route marker with 10 cm x 10 cm x 5cm thick GI plate with inscription there on, bolted/welded to 35mmx35mmx6mm angle iron, 60 cm long and fixing the same in ground

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a) 4-way (4+12) Double Door

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commisioning etc as required a)63 amps

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required

Laying of one number PVC sheathed /XLPE power cable of 1.1 KV grade of following size in the existing RCC/Hume/Metal pipe as required.

Upto 35 sq.mm

above 35 sq.mm and upto 95 sqmm

Erection of metallic pole of following length in cement concrete 1:3:6 ( 1 Cement:3 Coarse sand: 6 Graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc as required a)above 4.5mtrs and upto 6.5 mtrs

Earthing with copper earth plate 600 mm x 600 mm x 3mm thick including accessories and providing masonry enclosure with cover plate having locking arrangements and watering pipe of 2.7 meter long etc with charcoal/coke and salt as required

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required

63 mm dia (OD-63 mm & ID-51 mm nominal)

90 mm dia (OD-90 mm & ID-76 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

Supplying and fixing 2-way PVC gang box of 180 mm X 100 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet vover in front including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps. piano type switch, connection, painting etc. as required.

Supplying and fixing of 2-way PVC gang box of 150mmx75mmx60mm deep(nominal size) on surface or in recess with suitable size phenolic laminated sheet cover in front including providing and fixing of 3-pin 05/06 amps PT socket outlet and 05/06 amps PT switch connections,painting etc as required.

Supplying of energy saving LED canopy Luminarie 80 watts,suitable for lighting under canopy of fuel stations Make; Havells Model: BAYBRITE FLARE , BAYBRITEFLARE80WLED857PWBBOLTG or its equivalent to ISI specification as approved by Engineer-in Charge.

Supplying of energy saving LED Street Light 40 watts, made up of pressure die cast aluminium housing of make; Havells Model: ENDURA PEARL NEO,ENDURAPEARLNEOSWLED757PASYTOPC or its equivalent to ISI specification as approved by Engineer-in Charge.

Supplying of 5 star 32W energy saving A.C Ceiling fan (1200mm sweep) for operation on 230v, i/c wiring down rod standard length (upto 30Cm) with all accessories etc as required of Make:-Havells, Model : Efficiencia(BLDC 32W) or its Equivalent to ISI specification as approved by EIC.

Supplying of Exhaust Fans Mettalic type (300mm -12" sweep,) with all accessories as required of Make :Havells, Model :Ventil Air-DB NEO or its equivalent to ISI specification as approved by EIC.

Supplying of following LED lamps 09 watts Voltage - 230 Volts Lumen 6500 K, Make- Havells or equivalent to ISI.

Supplying & fixing of 20 watts LED lamps with light output of 6500 K lumen , make- Havells or its equivalent

Supplying of following size ISI marked PVC insulated and PVC sheathed/ XLPE (heavy duty) 1.1 KV grade ArmouredAluminium conductor cable conforming to IS:7098 (Part - I ).

16 sqmm x 2.0 core

50 sqmm x 3.5 core

95 sqmm x 3.5 core

Fabrication and supplying of street light Pole made out of 65 mm dia 'B" class ISI marked GI pipe of 06 mtrs long with earth stud and coupled with 01 no 50 mm dia, 1.5 mtrs long B class ISI marked single arm i/c bending the pipe with required shape and fixed at the top of the pole with necessary reducer/coupler, 300 mm x 300 mm x 6 mm thick base plate welded at the bottom of the pole, fixing of SMC box of size 200x140x95mm, 04 way connector and 06 amps MCB with clamping arrangement for SMC box i/c painting with one coat of mettalic primer and two coats of synthetic enamel paintas required as per the direction of Engineer-in-charge

Supplying, Installation, testing and Commissioning of wall mounted split type Inverter Air Conditioner of 1.5 Ton capacity with atleast 5 star rating by BEE and copper condenser with all accessories of Make: Blue Star Model:IC518DATU or its equivalent to ISI specification as approved by EIC i/c cutting, drilling holes on the wall for passing gas pipes, fixing suitable size PVC pipe on the wall through the holes and cementing, painting to give an even look and smooth finish, wrapping PVC non adhesive white tape over insulation of gas pipe etc.i/c supplying & fixing of 4 KVA Voltage stabilizer suitable for 1.5 Ton AC , Make: V- Guard model VND 400 or ISI brand ,Stand/bracket for outer unit,connections etc. as required as per direction of Engineer - in - Charge.

Supplying, Installation, testing and Commissioning of wall mounted split type Inverter Air Conditioner of 1.0 Ton capacity with atleast 5 star rating by BEE and copper condenser with all accessories of Make: Blue Star Model:IC512DATU or its equivalent to ISI specification as approved by EIC i/c cutting, drilling holes on the wall for passing gas pipes, fixing suitable size PVC pipe on the wall through the holes and cementing, painting to give an even look and smooth finish, wrapping PVC non adhesive white tape over insulation of gas pipe etc.i/c supplying & fixing of 4 KVA Voltage stabilizer suitable for 1.0 Ton AC , Make: V- Guard model VND 400 or ISI brand ,Stand/bracket for outer unit,connections etc. as required as per direction of Engineer - in - Charge.

Supplying and fixing Co2 Type fire Extinguisher of capacity 2 Kg with ISI Mark etc as reqd.

Supplying and fixing of W.Co2 Type Cartridge Operated ( 60Gm as per IS 4947) Type Fire Extinguisher 9 Ltr Capacity with ISI Mark conforming to IS: 15683 etc as reqd.

Supplying and fixing of Mechanical Foam Cartridge Operated (60 Gm as per IS 4947) Type Fire Extinguisher Filled with AFFF Foam 9 Ltr Capacity with ISI Mark conforming to IS: 15683 etc as reqd.

Supplying and fixing Fire Bucket including bracket and hooks for mounting with ISI Mark etc as reqd.

Supplying, installation and testing and commisioning of KOEL iGreen HA394 TCI G1 Model 42 HP @1500 RPM Three Cylinder Vertical Air Cooled Diesel Oil Engine Directly Coupled with KOEL Green Make AC Alternator 03 Phase 415 Volts 50 HZ @ 0.8 PF self excited self regulated designed to run at 1500 RPM 20 KW/25 KVA DG SET with Acoustics Enclosure (Sound proof) a sper central pollution control Board CPCB-II approved DG SET with complete accessories including 12 Volt 120 AH Battery as required as per the direction of Engineer-in-charge

C.M.ROY CONSTRUCTION

RAVI REALCONS PRIVATE LIMITED