Construction of Advance Training and Skill Development Centre Building on Plot Bearing CTS No. 209 at Worli, Mumbai

Amount

Providing Heavy Duty Fibre Glass Reinforced Plastic Temporary Barricade of 1.75 metre hight, with base width of 430 milimetre as a provision to accept water ballasting of 101 Itrs-110 Ltrs approx. and arrangement for traffic diversion such as traffic signals during construction at site, for day and night as per requirement. The raw material shall be UV stabilized Linear Low Density Polyethylene and should meet the requirements stipulated in standard Indian Standard: 10146-1982, Indian Standard:10141-1982 and should also comply to FDA:CFR Title 21.177.1520. Olefin Polymers , with specific FRP Grade 300-104 reinforced during moulding process to the permissible extent for improved impact strength. Qualification Criteria: For qualifying the sample , few tests shall be performed at Government Lab OR NABL Accredited Lab on Site Safety Fence sample, failure or deviations in test results of sample shall be disqualified.The tests and qualifying results are as under, (a) tensile strength at yield by ASTM D 638 =20.93 mPA, (b) Elongation at break ASTM D 638 = 121.66 mPA (c) Flexural Modulus ASTM D 790 = 633.76 mPA (d) Izod Impact Strenth (Notched) ASTM D 256 = 4.41Kilogram/ One Square Metre (e) Izod Impact Strenth (Un-Notched) ASTM D 256 = 67.04Kilogram/ One Square Metre (f) Drop Impact strength 25KilogramLoad from 1 metre, 2 metre & 5 metre height the weight of empty single Rotomoulded Plastic Barricade without water ballasting shall be 34 Kilograms approx. & total weight after water allasting shall be 135 Kilograms -140 Kilograms +/- 5 Kilograms (tolarance)The main Barricade body of hight 1750 mm approx is connected with the Extension body through 4 set of nut bolt washers .extenstion body through 4 set of nut bolt washers. Extension body is designed with 9 Nos kiss offs on rear side; the dimension of Extension body are 1500 milimetre (length),70 milimetre (width),250 milimetre(effetive height after fixing ) & dimension of its male collarare 1420 milimetre(length),25 milimetre (width),30 milimetre approx ( height), it is inserted in U groove provisioned on top of main body Barricade Model for interlconnecting.the minimum thickness of all over surface of plastic barricaed shall be 5milimetre +/- 20%.the rear bottam shall have to provision to fix two brackets at both end in corner for anchoring purpose .each rear bracket is constructed through rod of Diametre 60 milimetre with curvature welded with Mild Steel strip of 3 milimetre thick ,50 milimetre width and 90milimetre length at its top and base ,effective bracket shall be 410 milimetre approx. the anchoring hole in each bracket shall be 18 milimetre diametre for routine the Mild Steel bolts of 16 milimetre thickness and 150 milimetre length with sharp pointed edge at one end .the upper part of each bracket shall have a slot size of 30milimetre x 10 milimetre for connecting it with barracade model through bolts.similarly front bracket for site safety fence is 3 milimetre thick ,50 milimetre width, feective height after single bend is 230 milimetre and anchoring in each bracket shall be dia 18 milimetre unique safety feature for firm gripping to prevent from displacement and falling when inter connected even without water filling . There shall be 7 no's premoulded inserts on site Safety Fence for following application: 2no's for safety latches interconnectivity, 2 no's for fixing rear brackets for anchoring, one One Number at front side for fixing the front bracket for higher stability, and 2 nos on Extension top for holding light brackets / Rod for cloth holding. The plastic barricades has a strong vertical rib of 1740 milimetre length at the rear centre & 72 No's of kiss offs spread on entire rear surface , the water container (bottom) will also be equipped with 2 additional ribs on top to withstand nominal load if applied over its surface. The Fibre glass Reinforced Plastic Site Safety Fence shall have one drain bung insert moulded with plastic plug , two injection moulded water caps/ lids for base tank, and one yellow black zebra reflective tape as integrated accessories. Please refer the detailed drawing of Site Safety Fence. During construction barricading and arrangement for traffic diversion has to be kept contonuously and maintained properly till the completion of all the activities. All required Project details as per standards shall be screen printed on each board. Other requirements as per Specification in Contract. with prior approval of concerned Superitending Engineer. Site Safety Fence (2.00 Mtrs(H)) (Efficient Substitution to sheet Metal Barricade) , Empty Weight : 17.00 Kilogram/ Rgm,Weight Full : 70.00 Kilogram/ Rgm approx. (After Water / Sand Filling)

Empty boring for 725 to 1050 milimetre diametre bored Reinforced Cement Concrete cast in situ piles including withdrawal of shell, removal of earth to a distance of 50 metres et cetera complete. Spec :(As directed by Engineer in Charge)

Chiseling through pile shells in hard strata like boulders, soft and hard rocks Beyond 750 milimetre and upto and inclusive of 900 milimetre diametre including removing and stacking the loose materials et cetera complete and disposing of the unserviceable materials outside complete.

Providing bentonite slurry process for various diameter of piles vide Item Nos 1 (i to xxiv) above. Spec : (As directed by Engineer in Charge)

Carrying out load test for 1.5 times the proposed safe working load on the pile in driven position above 550 milimetre and upto 650 milimetre diameter including construction of test cap, use of accessories and instruments including providing graphs as per Indian Standard code or Standard Specifications and dismantling the test cap after testing and cleaning the site complete.

Chipping and dressing of the Reinforced Cement Concrete piles upto 0.60 meter including cleaning reinforcement and removal of dismantled materials upto a distance of 50 meter beyond the building area et cetera for providing pile caps. Specification :(As directed by Engineer in Charge)

Dewatering on Break HorsePower basis by using water pump including diversion of stream, providing cofferdams, earthern bunds et cetera as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 3.0 Break HorsePower pump et cetera complete. (prior approval of Superintending Engineer will be necessary)

Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 800 milimetre diameter. or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge includingplacing with fully automatic micro processor based processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical Shaft Impactor Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell et cetera complete. (Excluding steel reinforcement)

Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area .

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting et cetera complete. (Lift upto 1.5 metre) By Mechanical Means

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50metre and spreading for embankment or stacking as directed.

Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting et cetera complete. (Lift upto 1.50 metre) By Mechanical Means

Excavation for foundation in hard murum and boulders including removing the excavated material up to a distance 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting et cetera complete. (Lift upto 1.5metre) By Mechanical Means

Providing preconstructional antitermite treatment as per Indian Standard 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Providing preconstructional antitermite treatment as per Indian Standard 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper.

Providing preconstructional antitermite treatment as per Indian Standard 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 Cement Mortor diametre about 30 -60 centimetre deep at 15 centimetre centre to centre as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper.

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding / steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing et cetera complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin et cetera (Wooden centering will not be allowed.),with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade)

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 centimetre to 20 centimetre thick including hand packing and compacting et cetera complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 centimetre to 20 centimetre including watering and compaction et cetera complete.

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap metal for Reinforced Cement Concrete pile caps as per detailed designs and drawings, including bailing out water manually, centering, formwork, laying/ pumping, compacting, finishing and curing et cetera with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade) complete (Excluding steel reinforcement)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for Reinforced Cement Concrete work in foundations like raft, strip foundations, grillage and footings of Reinforced Cement Concretecolumns and steel stanchions et cetera columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing et cetera complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade)

Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for Reinforced Cement Concrete work in foundations like raft, strip foundations, grillage and footings of Reinforced Cement Concrete columns and steel stanchions et cetera including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) et cetera complete, with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for Reinforced Cement Concrete columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing et cetera complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft ImpactorGrade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for Reinforced Cement Concrete columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing et cetera complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade) (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite/quartzite/ gneiss metal for Reinforced Cement Concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing et cetera complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for Reinforced Cement Concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing et cetera. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade) (A) Ground Floor

(B) First Floor Parking

Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera. complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade) (B) 1st Floor to 21 Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for Reinforced Cement Concrete slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade) (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade) (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite/granite /gneiss metal for Reinforced Cement Concrete Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with Cement Mortor 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing et cetera complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin et cetera) with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft Impactor Grade) (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical shaft ImpactorGrade) (A) Ground Floor

(V) 16 th Floor

Providing and laying in situ cement concrete M -30 with tremix treatment for 200 milimetre thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4 milimetre wide and 20 milimetre deep with necessary refilling with bitumen ( excluding reinforcement) with coarse and fine aggregate ( natural sand/ Vertical shaft ImpactorI grade finely washed crushed sand) et cetera complete with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / granite/gneiss / quartzite metal for Reinforced Cement Concrete fins of required thickness in position as shown on the drawings or as directed by Engineer-in-charge including steel centering, plywood / steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with Cement Mortor 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing et cetera complete. (Excluding reinforcement, including cover block) Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin et cetera with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) et cetera complete. With fine aggregate (Crushed sand Vertical Shaft Impactor Grade)

Providing and fixing in position High Corrosion Resistant Material / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for Reinforced Cement Concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches et cetera as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees et cetera as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces et cetera. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade et cetera complete. (V) 16 th Floor

Providing second class Burnt Brick masonry with conventional/ Indian Standard type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering et cetera Complete.

Providing second class Burnt Brick masonry with conventional/ Indian Standard type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding et cetera Complete (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing second class Burnt Brick masonry with conventional/ Indian Standard type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 milimetre diameter / 2 hoop iron strips 25 milimetreX 1.6 milimetre placed at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing internal / external 12 milimetre thick Ready Mix plaster confirming to Indian Standard:4031(Part-4) 1988 and Indian Standard 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4 Percent, to all type of surfaces in all positions including scaffolding and curing complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, et cetera complete. (B) 1st Floor to 21 Floor

Providing internal cement plaster 20milimetre thick in a single coat using Ready to use wall plaster to concrete, brick surfaces in all positions including scaffolding and curing. Providing groove at joint of Burnt Brick Masonry and concrete members complete. b) cement mortar 1:4 With Prior Approval of Concerned S.E. (A) Ground Floor

(V) 16 th Floor

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 milimetre thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 milimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding et (A) Ground Floor cetera complete.

(B) 1st Floor to 21 Floor

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimetre thickness on previously plastered surface, including Plaster Groove 6 milimetre thickness or Tape Grooves 35 to 45 millimetre thickness or as required, in all position including preparing the surface, scaffolding et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing internal cement plaster 20 milimetre thick in a single coat using Ready to use wall plaster to concrete, brick surfaces in all positions including scaffolding and curing. Providing groove at joint ofBurnt Brick Masonry and concrete members complete C ) cement mortar 1:3 With Prior Approval of Concerned S.E. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing fine cement finish 1.5 milimetre thick over green plaster surface including scaffolding curing et cetra complete. (A) Ground Floor

(V) 16 th Floor

Providing patti/ band 150 milimetre wide on plastered surface 12 milimetre to 15 milimetre thick in Cement Mortor 1:3 line and level including neat finishing scaffolding curing et cetera complete. (A) Stilt Floor

(V) 16 th Floor

Providing and fixing chicken mesh of 22 gauge, with about 30 centimetre width at the junction of Reinforced Cement Concrete members and brick/ Autoclave Areated Concrete block work, of approved quality including fixing mesh in position by necessary drilling in concrete / Burnt Brick masonry/ Autoclave Areated Concrete block masonry and/ or tying by binding wire etcetera complete. as directed. (including all lead and lifts)

Providing and fixing machine cut machine polished 18 milimetre to 20 milimetre thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and laying in situ cement concrete M30 with tremix treatment for 200 milimetre thickness for flooring with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumen et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and Laying hot applied thermoplastic road marking strip on Bituminous Surface of specified shade/ colour of 2.5 milimetre thick including 1.5 Refractive index reflectorizing glass beads @ 250 gram per square metre Thickness of 2.5 milimetre is exclusive of surface applied glass beads as per IRC 35:2015. Initial Dry reflectivity RL shall be > 250 mcd/square metre/illumination measured in the initial 7 days and sustained reflectivity RL of 100 mcd/square metre/illumination and Qd of 100 mcd/square metre/illumination ux measured at the end of 2 years by means of a Standard Reflectometer of Zehntner, Easylux, Delta make capable of measuring RL & QD both according to IRC 35:2015 clause 15.5. The finished surface to be level, uniform, and free from streaks and holes complete as per direction of Engineer-in-charge and in accordance with applicable specifications.(Refer MORTH Clause 803 for technical Specification and Performance for IRC 35:2015). (B) 1st Floor to 21 Floor

Providing and laying vitrified matt fininsh tiles having size 590 milimetre to 605milimetre x to 605 milimetre of 8 to 10 milimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and laying vitrified mirror / glossy finish tiles having size 590 milimetre to 605 milimetre x 590 milimetreto 605 mm of 8 to 10 milimetre thickness and confirming to Indian Standard 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing et cetara complete (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and laying vitrified matt fininsh tiles having size 590 milimetre to 605milimetre x to 605 milimetre of 8 to 10 milimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning et cetera complete. (B) 1st Floor to 21 Floor

Providing and laying vitrified matt finish tiles having size 590 milimetre to 605 milimetre x to 605 milimetre of 8 to 10 milimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning et cetera complete. (B) 1st Floor to 21 Floor

Providing waterproof plaster in Water Closet and bath 20 milimetre thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) et cetera complete. (B) 1st Floor to 21 Floor

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 milimetre to 20 milimetre thick on bed 1:6 cement mortar including cement floats striking joints, pointing in Cement Mortor 1:3 curing and cleaning et cetera complete. (A) Ground Floor

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 milimetre to 20 milimetre thick on bed 1:6 cement mortar including cement floats striking joints, pointing in Cement Mortor 1:3 curing and cleaning et cetera complete. (B) 1st Floor to 21 Floor

Providing and laying machine cut machine Polished Kota stone flooring 25 milimetre to 30 milimetrethick and required width in plain/ diamond pattern on bed of 1:6 Cement Mortor including cement float, filling joints with neat cement slurry, curing, polishing and cleaning et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing in required position skirting or dado of polished Kotah Stone slab 25 milimetre to 30 milimetre thick fixed on base on plaster of cement mortar 1:4 including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing & Fixing in position, Acoustical Panelling made from Fabric wrapped Compressed polyester fibre nonwoven 9 milimetre panels on, 50 x 50 milimetre sal-wood frame of 600 x 600 centre to centre having wooden supports from wall of required length, in front of 1000 gsm synthetic wool 50 milimetre thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing et cetera complete (B) 1st Floor to 21 Floor

Providing & Fixing in position, Acoustical Ceiling made from Gypsum Plain Panels on approved heavy duty Galvanised Iron frame ceiling channels at 450 centre to centre, & intermediate channels not more than 1200 centre to centre, along with ply wood forms suspended with Hangers from Roof, in front of 1000 Gsm synthetic wool 50 milimetre thick, with Paint, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing et cetera complete (B) 1st Floor to 21 Floor

Providing & fixing in position Stage flooring Made from 18mm plywood 1200 x 2400 & 18milimetre Teakwood planks 100 x 800 having tongue & grove on Sal-wood frame of 50 x 100 at 600 milimetre centre to centre on stage surface including cost of required Cut-Outs, decorative mouldings / finishing-items / polish et cetera, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. .including all materials labour,finishing et cetera complete (B) 1st Floor to 21 Floor

Providing & Fixing in position Acoustical Doors along with 150 x 150 milimetre teak wood frame, doors made from 50mm Teak wood frame 600 x600 centre to centre filled with 1000 Gsm synthetic wool 50 milimetre thick and 3 milimetreTecsound from both sides, 12 milimetre waterproof ply & veneer from both sides , including 150 milimetre heavy duty SS hinges (Geze / Dorma or eq.) 4 no each leaf, with Door-closer (Dorma / Geze or eq.) including cost of required Cut-Outs, decorative mouldings / finishing-items / melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects .including all materials labour,finishing et cetera complete (B) 1st Floor to 21 Floor

Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 milimetre x 450 milimetre size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 milimetre thick supports with kadappah top 35 to 40 milimetre thick and polished granite 16 to 20 milimetre top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 centimetre height and top granite of 75 x 40 centimetre including cutting, opening for sink of required size in kadappah as well as granite et cetera complete. (Platform top size 5.00 metre x 0.60 metre and height is 0.75 metre) (B) 1st Floor to 21 Floor

Kitchen Trolley : Providing and Fixing stainless steel kitchen trolley of overall 26 " height and 22" depth,supported on aluminium pipes ,trolley basket made out of 5 milimetre stainless steel rod fitted on telescopic channel of size 1.5 " x 20 " x 22 " on both sides of trolley of 12 " or above size, panel having 40Kilogramload bearing capacity of trolley made out of 20 milimetre PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica ,100 milimetre stainles steel decorative handle.(The width and height of individual compartments shall be kept as directed by Engineer-in-charge) (B) 1st Floor to 21 Floor

Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 milimetre thick for door frame/ dado/ window boxing et cetera On Cement Mortor 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300 milimetre x 40 milimetre x 5 milimetre with oil painting, et cetera complete (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing M40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to Indian Standard 65241983 having 6 milimetre diametre bars 3 Nos. And stirrups @250 milimetre centre to centre and fixing in wall with 6 Nos of hold fast of 12 milimetre diametre bars 500 milimetre long including primer and oil painting et cetera, complete) frame size 60 milimetre x 100 milimetre (V) 16 th Floor

Providing and fixing solid core flush door shutter in single leaf 32 milimetre thick decorative type of exterior grade as per detailed drawings approved face veneers 3 milimetre thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing solid core flush door shutter in double leaf 32 milimetre thick decorative type of exterior grade as per detailed drawings approved face veneers 3 milimetre thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

P/F marine treated watreproof Solid Core Flush Door of 35 milimetre thick in Single Leaf of requisite manufactures i.e nehor/Century/Greenply/Kenwood or equivalent generally confirming to Indian Standard 1659.1990 finished with 1.5 milimetre thick formica laminate sheet (Royale Touche) of approved pattern with or without grooves on both sdes, necessary BTC beauty from all four edges & the shutter with three years guarantee requisite stamp paper fixed with approved heavy type Stainless Steel finish decorative fixtures & fastners suc as heavy type,aldrop, tadi ,tower bolt,handles,hinges etc. melamine polishing to beading pati including all leads & lifts as per drawng and instructions of Engineer-n-charge, et cetera Complete. (B) 1st Floor to 21 Floor

Providing and fixing in position fully glazed aluminum door made up of xtruded and anodised aluminium sections of approved make and of size 63.5 milimetre x 38.10 milimetre x 2.0 milimetre thk , 47.62 milimetre x 10.16 milimetrex 1.74 milimetre thk (wt. .881kilogram per running Meter) for outer frame, 47.62 milimetre x 10.16 milimetre x 1.74 milimetre thk (wt. 0.881 kilogram per running Meter) for top rail, 95.25 milimetre x 25.40 meter x 2.0 milimetre hk (wt. 1.519 kilogram per running Meter) for ottom rail, 25.0 milimetre x 44.45milimetre x 2.40 milimetrethk (wt. 0.918 kilogram per running Mete) for lock rail, 47.62 milimetre x 44.45 milimetre x 1.88 milimetre thk (wt. 0.943 kilogram per running Mete) for vertical of shutter (hinges side), 47.52 milimetre x 44.45 milimetre x 1.95 milimetre thk (wt. 0.936 kkilogram per running Mete) for vertical of shutter (latch side), clip weighing 0.097/kilogram per running Mete., with 5 mm thick plain / frosted / tinted glass in shutter including neoprene gasket, fixtures, fastenings and accesories like hinges, locking rrangement, door closer et cetera, complete as directed by Engineer In harge. (Note: anodic film must not be less than 15 microns i.e. AC-15 as per Indian Standard, the anodizing must be scaleted by keeping the anodized section in boiling de-anodized water for a period of one hour) (B) 1st Floor to 21 Floor

Providing and fixing steel frame door of angle 50 x 50 x 6 milimetre with mild steel bars 16 milimetre diametre horizontally at 10 milimetre centre to centre for ventilator portion including iron hold fast boxes for fixing shutters including welding, finishing, painting et cetera complete. (B) 1st Floor to 21 Floor

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10.mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design. duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PAG grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:-Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875- Part 3 (ii) Sites with structure height more than 20m for all wind speeds 9.147.A1.2 Using R3 series with frame (55mm & above) x (40mm & above) & sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system (Height upto 1.8m (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 milimetre x 1.22 milimetre box type, 5 milimetre thick sheet glass louvers, of approved quality et cetera complete. (B) 1st Floor to 21 Floor

Providing and fixing mild steel grill work for windows, ventilators, et cetera 15 Kilogram/ One Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 milimetre dia. and vertical pipe of 38 milimetre dia at 0.60 metre centre to centre or as required and horizontal pipes of 25 milimetre dia in three rows, all pipes of 2 milimetre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 milimetre dia above newel post of 75 milimetre diameter et cetera complete (Prior approval of sample and brand by Ex.Engineer is necessary before use) (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing 900 milimetre high Stainless Steel 304 Grade Stainless steel railing with 40mm diameter and 1.5 milimetre thick at top, 40 milimetre diameter and 1.5 milimetre thick vertical supports spaced at 1.5 metre center to center and 8 milimetre thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe et cetera complete (B) 1st Floor to 21 Floor

Directional signage : Design, supply, fabrication and fixing acrylic multilingual Braille (raised dots) directional signboards of size 6" x 9" designed as per accessibility standards and having 4milimetre thick acrylic base plate with Upper Case San Serif words made of white acrylic non glare cut out letters of height 15mm raised not less than 0.8 milimetre above base plate and the equivalent word written in Hindi with Devnagri non glare acrylic letters of height 15 milimetre raised not less than 0.8 milimetre above base plate and having a non glare acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per manufacturers specifications on the wall at the approved location and at a height of 1200 milimetre from FFL and as per the directions by the engineer in charge. (A) Ground Floor

(B) 1st Floor to 21 Floor

Fire exit and floor identification signage as per manufacturer's specifications, ADA compliant and modular system (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing 90 centimetre x 60 centimetre Granite plate engraving 10 centimetre Height letter, figures including painting the lefters/figures with approved colour and shade complete

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per Indian Standard 875 (Part-III). The Suspended System held with Spider Fittings of Stainless Steel-316 Grade Steel of approved manufacturer with glass panel having 12 milimetre thick clear toughened glass held together with Stainless Steel- 316 Grade tainless steel Spider & bolt assembly with aminated glass fins 21 milimetre thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of Stainless Steel- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using Stainless Steel channel of 50x25x2 milimetre using astener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and eparators to prevent bi-metallic contacts, all complete to perform as per specification and pproved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements et cetera The joints between glass panels (6 to 8 milimetre) and gaps at the perimeter & in U channel of the assembly to be filled with non taining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 milimetre minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 milimetre size for flange, Mild Steel flat for top runner of minimum size 40 x 12 milimetre with roller wheels confirming to grade Folding Gate 150 fitted with snap headed rivets of minimum size 6 milimetre max. spacing of vertical channels be 100 milimetre enclosed gate position and clear space of 150 milimetre between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting et cetera complete. (Indian Standard 105211983). (V) 16 th Floor

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (excluding the primer coat)et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing & Applying two coats of fiber Reinforced liquid applied membrane of asian paints of equivalent make, having crack bridging ability upto 2milimetre, superior anti carbonation with lift of 10 years ensuring forced coverage of 160 microns, applying one coat of thick acrylic base texture (2milimetre to 2.5milimetre Thk) & after 8 Hrs applying two coats of organo silicon with VOC less than 30 grams / Lits, UV cross linking emulsion having advance anti algal, Excellent DPUR for dirt Pick up resistance. (Colour Stay) resistance to fading of Colours, protection against bird dropping and paint performance warranty for 15 Yrs on requisite stamp paper so as to obtain an acceptable finish & ensuring minimum 40 microns thk for 2 coats as directed by engineer incharge. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil, grease, dirt and other materials as required, et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding Indian Standard of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days et cetera complete.

Providing and fixing Modular false ceiling of 600 x 600 milimetre center to center and 13 milimetre thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T 2”x1 ½” (50 milimetre x 40 milimetre) weighing 0.39 Kilogram per metre at 60 centimetre center center and fixed with ½” x ½” (15 x 15 milimetre) flanges weighing 0.19 Kilogram per metre suspended on 6 milimetre diametre mild steel rod weighing 0.22 Kilogram per metre, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 milimetre x 40 milimetre) weighing 0.39 Kilogram per metre et cetera (all alluminium sections shall be anodized) including all labour, material, lifts et cetera complete. (B) 1st Floor to 21 Floor

Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended Galvanised Iron Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 milimetre maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts et cetera all complete. (B) 1st Floor to 21 Floor

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in Cement Mortor 1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with Cement Mortor 1:3 admixed with approved water proofing compound and finally top finishing with average 20 milimetre thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 milimetre x 300 milimetre making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test et cetera complete. (V) 16 th Floor

Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for Reinforced Cement Concrete / cementitious surface for terrace waterproofing on Burnt Brick Coba / Reinforced Cement Concrete , after application of TP- 42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 grams per One Square Metre and applying 2nd coat of Polydee-LM @ 700 grams per One Square Metre and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25milimetre cement plaster for protection with fibrillated 6 milimetre Plyplast fibre @ 125 grams per One Square Metre to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- et cetera complete. (B) 1st Floor to 21 Floor

Supplying hard murum/ kankar at the road site, including conveying and stacking complete.

Spreading hard murum/ soft murrum/ gravel or kankar for side width complete

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering et cetera complete.

Providing and laying cement concrete pipe of Indian Standard 458:2003 Non pressure-2 class of 450 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing et cetera complete.

Providing and fixing on walls/ ceiling/ floors, 40 milimetre diametre heavy grade having embossed as Indian Standard Institute Mark galvanised iron pipes weight of 4.49 Kilogram/meter with necessary fittings and remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed et cetera complete.

Providing and fixing on walls/ ceiling/ floors, 50 milimetre dia heavy grade having embossed as Indian Standard Institute Mark galvanised iron pipes weight of 6.33 Kilogram/meter with necessary fittings.and remaking good the demolished portion and primer of anti corrossive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed et cetera complete.

Providing and fixing on walls/ ceiling/ floors, 80 milimetre diametre heavy grade having embossed as Indian Standard Institute Mark galvanised iron pipes weight of 10.15 Kilogram/meter with necessary fittings. and remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed et cetera complete.

Providing and fixing on walls/ ceiling/ floor 15 milimetre diametre Chlorinated Poly Venyl Chloride pipe with necessary fittings, remaking good the demolished portion et cetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing on walls/ceiling/floor 20 milimetre Diametre Chlorinated Poly Venyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing on walls/ ceiling/ floor 25 milimetre diametre Chlorinated Poly Venyl Chloride pipe with necessary fittings, remaking good the demolished portion et cetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing on walls/ ceiling/ floor 32 milimetre diametre Chlorinated Poly Venyl Chloride pipe with necessary fittings, remaking good the demolished portion et cetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing on walls /ceiling/ floor 40 milimetre diametre Chlorinated Poly Venyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing Poly Vinyl Chloride Rain water pipes of 110 milimetre outer diameter and having wall thickness of 2.2 to 2.7 milimetre confirming to Indian Standard 13592-1992 including proper rainwater receiving recess with Poly Vinyl Chloride plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25 milimetre to 40 milimetre from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on Cement Concrete or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the Poly Vinyl Chloride fittings and additional 2 piece socket clips shall be got approved from engineer in charge et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing 75 milimetre diametre stabiliser pipe/ Poly Vinyl Chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps et cetera complete

Providing and fixing 15 centimetre x 10 centimetre salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and laying concrete pipes of Indian Standard Non pressure class of 225 milimetre diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying concrete pipes of Indian Standard Non pressure class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and fixing Chrome Plated 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut et cetera complete as directed by Engineer in charge. (B) 1st Floor to 21 Floor

Providing and fixing screw down 15 milimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete (B) 1st Floor to 21 Floor

Providing and fixing 10 centimetre Poly Vinyl Chloride nahani trap with grating et cetera complete. (B) 1st Floor to 21 Floor

Providing and fixing 15 milimetre diameter concussion push button type brass/gun metal self- closing tap including necessary socket complete. (B) 1st Floor to 21 Floor

Providing and fixing European type white glazed earthenware water closet pan with Unplactised Poly Vinyl Chloride seat and lid with chromium plated brass hinges and rubber buffers including Unplactised Poly Vinyl Chloride and vent pipe up to the outside face of wall 10 litre enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 milimetre diametre Unplactised Poly Vinyl Chloride flush pipe with fittings and clamps ,20 milimetre diametre Unplactised Poly Vinyl Chloride overflow pipe ,mosquito proof couplings Galvanised Iron chain and pulley,with water Jet and fitting including cutting and making good to the walls and floors testing et cetera complete.(prior approval of sample and brand by Ex. Engineer is necessary before use) (B) 1st Floor to 21 Floor

Providing and Fixing toilet set for differently Abled persons consist of Floor Mounted white vitreous china water Closet including 6 litre capacity white vitreous china flushing Cistern with raised soft-push button, white vitreous china wash basin of size 46 x 36 centimetre and one no Stainless Steel 304 hinged rail 76 centimetre & three no Stainless Steel 304of (Grab Bar) 60 centimetre all including cutting and making good the walls and floors wherever required ,seat cover, cistern & wash basin fittings,nuts, bolts and gasket et cetera complete as per the direction of Engineer-In-charge. (B) 1st Floor

Providing and fixing ISI marked double swing flush door shutters conforming to Indian Standard :2202 (Part I) Non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 milimetre thick including Indian Standard Institute marked Stainless Steel L- hinges with necessary screws Fittings & Fixtures per leaf SS kick plates on both sides of the door of 300mm height Heavy Duty satin finish butt SS Hinges (100mm x 75mm x 3mm in size) -4 nos. SS finished lever handle with mortise lock- 1 One Number Floor spring- 1 One Number 100mm x 100mm safety glass at the specified location (B) 1st Floor

Providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black / coloured granite of 180 milimetre thick stone black kadappa framework including chromium plated coupling bottle - Trap using CERA company or equivalent oval typa wash basin model no 3448 as per detailed drawing or as directed by engg incharge et cetera complete. (Counter size 1.20 metre x 0.60 metre ) (B) 1st Floor to 21 Floor

Providing and fixing Chrome Plated wall mixer with provision for overhead shower with 115 milimetre long bend pipe and wall flange of approved make including necessary sockets/union nut et cetera complete. (B) 1st Floor to 21 Floor

Providing and fixing 450 milimetre x 550 milimetre size superior type Belgium mirror with 16 milimetre diametre nickel plated towel rod et cetera complete. (B) 1st Floor to 21 Floor

Providing and fixing chromium plated towel rod 16 milimetre diametre and 75 centimetre in length including all accessories complete. (B) 1st Floor to 21 Floor

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40 milimetre dia Mild Steel tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with ild Steel . Tubes, Mild Steel tube challis, ild Steel clamps and staircase system in the scaffolding for working platform et cetera and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building et cetera, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen et cetera, complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing Jute Kantan (Tarat) screen to the scaffold-ing for external guniting as directed including removing the same after the work is over et cetera complete. (A) Ground Floor

(B) 1st Floor to 21 Floor

Providing and fixing High Density Polyethylene container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres (V) 16 th Floor

Providing and fixing 40 milimetre dia Ball cock medium type with Poly Venyl Chloride float including sockets and necessary fittings and tested as per municipal requirements et cetera complete. (V) 16 th Floor

Providing and fixing in position Unplactised Poly Vinyl Chloride ultra violet stabilized 110 milimetre outer diameter cowl dome confirming to Indian Standard-4985 including making joints with solvent cement et cetera complete (V) 16 th Floor

Providing and fixing Well Seasoned Burma Teakwood Eaves Board of design and size to match the existing original Historic Eaves Board dismantled from site or as directed by the Architect or Engineer in Charge. Item to include necessary cutting from larger section of wood if required, carving of mouldings et cetera to match the Historic detail on site. Eaves Board to be coated with Solignum or equivalent Anti-termite solution and finished with one coat of primer and two coats of synthetic enamel coat LeS of required finish as directed by the Architect including all necessary hardware, tools, scaffolding et cetera. to complete the item in all

Providing and fixing Plaster Of Paris mouldings/ cornice bands, of 6" Vertical Height including grooves in wall, opening side vertical band, architraves, lintels etc. Item to include applying Plaster Of Paris upto 1/2" thick to repair existing mouldings, cornice bands, architraves, lintels. pediment, ceiling, etc whenever indicated by the Architect or Engineer in charge. Item to include checking ali surfaces for proper line and level, scaffolding et cetera complete. Mode of Measurement: Height/Width of the moulding to be determined as per the vertical/Width of the same irrelevant of the horizantal depth & inclined dimensions.

Providing & Laying of Bharat Tiles of Heritage revival type 200 x 200 milimetre size, 14-16mm thick of plain colour laid in a combination of one or more colours as per the design indicated by the Architect and matching to the original flooring pattern for the corridor and verandah spaces on Ground + 1st +2nd floor, laid in cement mortar 1.5 to 3.5 centimetre cement : sand bed mortar of 36 grade cement of ratio not leaner than 1:4 with a neat cement slurry on top, of approved thickness. Joints should be as fine as possible and filled with matching cement mortar as directed by architects. Grounting is to be left for 2 Day and cured with water befor the tiles are to be subjected to the second coat of polishing using No. 2 stone following No. 3,4,5 and final polishing with 5x stones (very fine stones).

Provision of Bharat tile skirting 100 milimetre ht. x 200 milimetre width and thickness 25 milimetre using Plain tiles. Item complete with cement mortar 1:4 and finishing with 6 milimetre groove et cetera Rate to be inclusive of tile, storage, all duties and taxes applicable. (R.A attached)

Providing and fixing 30 milimetre thk scratch proof Engineered wooden flooring and skirting in deep walnut finish / teak finish of Pergo or equivalent make as per sample approved by the architect and company specifications. Item to include providing and fixing skirting matching to the flooring as per company details and design. (Basic Rate of the material as per company - Rs. 400 per square foot)

Providing & fixing 12 milimetre thick toughened clear float glass partition as per drawing and requirement using dorma make spider patch fittings as per their specification and requirement uplo a height of 13, Item to include 2 doors complete with hardware. Patch fittings (dorma or equivalent) to be used for the giass door as shown in the drawing at all necessary joints and depending on the weight of the glass. Item to include glass door lock in the centre et cetera complete

Providing and fixing glazing of clear glass of Asahi, Modi, Saint Gobain or equivalent make wilh a 6mm thickness and bevelled edges. Rate to be inclusive of beading patti to match the original design. Item to include careful removal of damagedi cracked/ missing glass panels on doors / windows and discarding the same.Item to include damaged door window shutters, ventilators arch et cereta of the same dacorative arched design, with beading patti, thickness and palem, including sealant putty et cereta complete

Providing & fixing of 25 milimetre to 50 milimetrethk basalt stone cladding as per shade and texture approved by the client/architect upto a maximum size of 1200x600 milimetre height and width as per equal divisions made on site.The cladding should be detailed with grooves fixed with cement sand mortar (1:4) done to match colour of stone as directed by Engineer in-charge including transportation, loading/ unloading, providing /supplying /laying /fixing, installing /fabricating /testing /commissioning et cetera on site. Basic Cost of stone Rs 375/- Sft

Providing and fixing stealth faucet jet spray of Kohler or equivalent make of approved quality including necessary socket / union, including necessary, bend and socket et cetera complete

Providing and fixing Rain Shower head of Kohler rainforest series or equivalent make as directed by the Architect including all necessary connections and piping et cetera complete

Providing and fixing recessed bath and shower faucet trim with lever handle and diverter bottom of Kohler Fairfax series or equivalent make including all necessary connections and piping et cetera complete

Providing and fixing Wall mounted Soap Dispenser of Kohler or Equivalent approved make and design. Item to include making holes and necessary hardware like screws et cetera. and making good the damages et cetera complete

Providing and fixing Chromium Plated wall mounted robe hooks of Kohler or equivalent approved make and design to hang clothes. Item to include making holes and necessary hardware like screws etc. and making good the damages etc, complete

Providing and fixing Chromium Plated Towel Rail 457 milimetre long of Kohler or equivalent make of approved quality fixed on chromium plated bracket including providing teak wood gutties in masonry et cetera complete

providing and fixing 12 min Chromium Plated 7 inch long pilar type cock of Kohler Fairfax series single control or equivalent/make as approved by Architect or Engineer in Charge, with deluxe knob for Wash Hand Basin or sink etc. complete

Providing and fixing Chrome Finish Concealed Stop Cock of Kohler or equivalent make including all necessary plumbing works required to complete item in all respects

Providing and fixing Chrome Finish Ängle Cock of Kohler or equivalent make including all recessary plumbing works required to complete item in all respects

Providing and lixing Chrome Finish 2-way Bib Cock of Kohler or equivalent make including all necessary plumbing works required to complete item in all respects

Drilling and boring through 600 milimetre thk masonry walls (horizontal / angular) as required to create passage for cables, a/c grouting / filling and making good tubing ducts 150-230 milimetre diametre as per architectural requirements, all labour, plant, tools, skilled manpower et cetera

Providing and fixing Granite Counter size shown on architects drawing, including cutting holes in the counter for basin and tap. rounding and polishing of edges will be in the scope of civil contractor as per design specified by the architect.

Providing and constructing Brick Masonry Inspection Chamber 60 centimetre x 45 centimetre With Reinforced Cement Concrete raft in Black Cotton soil area including cost of reinforcement, 1:2:4 cement concrete channels half round Glazed Stoneware pipes, Brick Masonry, plastering from inside and airtight 75 milimetre thick Reinforced Cement Concrete cover medium duty 100Kilogram et cetera complete.

Providing and constructing Brick Masonry Inspection Chamber 90 centimetre x 45 centimetre With Reinforced Cement Concrete raft in Black Cotton soil area including cost of reinforcement, 1:2:4 cement concrete channels half round Glazed Stoneware pipes pipes, Brick Masonry, plastering from inside and airtight with 75 milimetre thick Reinnforced Cement Concrete cover medium duty 140 Kilogram et cetera complete.

Providing and fixing 45 centimetre wide mild steel ladder of 40 milimetre x 6 milimetre mild steel flat stringers and steps of 18 milimetre diametre mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60 centimetre x 30 centimetre x 30 centimetreand painting the ladder complete. (Anti Corossive Paint)

Providing and making Indian Standard Institue Mark ferrule connection of 32 milimetre diametre to water main including ferrule coupling cast iron bell mouth cover, built in non return valve and fixing including excavation and reinstatement complete.

Providing, laying and fixing Poly Venyl Chloride pipe of 110 milimetre diametre with fittings such as bends, tees, reducers, clamps, et cetera including necessary excavation, trench filling et cetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in Public Work Depatment chowky or as directed et cetera complete.

Providing and fixing 25milimetre diameter water meter with non-return valve including strainer, sockets/ union nut and including water meter box making locking arrangement and lock. [Without chamber].

Providing and constructing Ductile Iron circular manhole 45 centimetre diametre At top 90 cm at bottom up to 1.80 meter to 2.70 meter depth including excavation, laying 1:4:8 cement concrete bedding 15 centimetre thick burnt brick mansonry with 1:1 cement mortar plaster 25 milimetre thick inside and outside 20 milimetre (1:3) ductile iron heavy type cover with ring 125Kilogramin weight. High strength. More life and Durability, Good Antiskid Grip, Suitable to heavy theatric loading, Light weight casting after cost benefits for Transportation Refilling et cetera as per requirement. with prior approval of concerned Superitending Engineer.

Providing soak pit of size 120 centimetre x 120 centimetre x 120 centimetre including excavating and filling with brick-bats.

Providing and fixing reinforced cement concrete cover of size 90 centimetre x 45 centimetre with frame over inspection chamber et cetera complete. Heavy duty (225 Kilogram)

Providing and fixing heavy duty inter locking concrete RUBBER MOULD GLOSSY PAVING BLOCKS of 60 millimeter thickness of having a strength of 400 Kilogram per square metre of approved quality and shape on a bed of crushed sand of 25 to 30 millimeter thick including striking joints and cleaning et cetera complete. (using 100% crushed sand)

Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade et cetera complete.(weight 18 Kilogram. to 20 Kilogram. Per Square metre)

Providing and erecting Y type barbed wire fencing with seven rows of wire with 2.45 milimetre dia Galvanised Iron pipe ( Rezan/ concentiDeleted ire 0.75 milimetre dia ) with hot dip and Galvanised Iron coated hooks as per drawing supported on Mild Steel angle 50 x 50 x 6 milimetre at 2.5 metre centre to centre including fixing and fastening with wire, painting Mild Steel angles with one coat of red lead primer and two coat of oil paint et cetera complete.

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kilogram tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 milimetre, 100 milimetre and 102 +/- 2 milimetre and with minimum reflective area of 13 Square centimetre on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 milimetre and height not less than 30+/- 2 milimetre) from the body is to be a minimum value of 500 Kilogram Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel, to the Engineer.

Providing & Fixing Stainless Steel Body Door's Stopper's.

Making 150 millimetre diametre Bore in all types of Strata with head core including survey for fixing location of bore transporting of machinery and platform, providing laying fixing casing of 150 millimetre diametre Unplacticised Poly Vinyl Chloride Pipe (CS as per IS:12815) having outer diametre 165 and minimum thickness of 5.70 to 6.50 millimetre diametre along with grouting, checking capacity by flushing test etc. complete. Survey for Location

Making Bore in all types of Strata

Providing and Laying and fixing casing of 150 millimetre diametre Ultra Poly Vinyl Chloride pipe to withstand continous internal hydraulic pressure of 6 kilogram per square centimetre (Cross Section as per IS:12818-1992) having outer diametre 165.40 millimetre and minimum thickness 5.70 to 6.50 millimetre along with grouting.

Checking Capacity by Flushing test

Supplying and erecting minimum Three & above star rated submersible pump set of 2.25 KW/3 HP with 415 V, 50 c/s AC supply suitable for 150 millimetre diametre. borewell suitable for 120 to 475 LPM discharge at 36 to 10 metre head & discharge & delivery Pipe of Size-50 milimetre diameter with a necessary H type clamps as per specification No. WP-SMP

Supplying and erecting flat flexible 3 core 2.5 square milimetre Poly Vinyl Chloride sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Supplying and erecting D.O.L. Starter 400V. 3 phase, 50 cycles with no volt coil and overload element with necessary materials and connected to supply upto 7.5 H.P. (Similar to L & T make MK-1 DOL Model)

Sub Work 1 : Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying and erecting 20mm dia. corrugated flexible polypropylene conduit

Supplying and erecting 25mm dia. corrugated flexible polypropylene conduit

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 1x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x10 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 4x16 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting Ceiling rose / Batten holder / Slanting holder /hanging cord switch / hanging bell push / pendant holder bakelite base 6A. erected on filled polypropylene board or polished double wooden block/PVC junction box.

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type computer Jack RJ45 with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Point wiring for independent plug, concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as perspecification No WG-PW/SW

Point wiring for light/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit/ casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WGPW/ HW

Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WGPW/ CW

Secondary point wiring for additional light/ bell point in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire with required accessories as per specification No: WG-PW/SW

Supplying & erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG- 11 as per specification No. WG-TW

Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC

Supplying and installing cat-6 STP cable suitable for networking complete as per specification.

Supplying and fixing 1 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying and fixing 3 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying, fixing, and configuring 24 ports with 4 (SFP+) port, ethernet managed switch with web view/CLI, 6KV surge protection on ethernet port and console port for management in provided rack as per specification no. WGNWC/ GBS

Supplying, fixing, and configuring broadband ADSL router with all accessories, on provided rack as per specification No. WG-NWC/ADSL

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying and fixing tool-less shutter keystone jack (RJ-45) in provided patch panel complete as per specification no. WG-NAS/KJ

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing 42U floor mount server rack (Dimension-DxWxH – 800x600x1866 mm) as per specification No. WG-NAS/RAK

Supplying, erecting & commissioning 20 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW

Supplying, erecting & commissioning 10 pair module for connection & disconnection of telephone cable as per specification no. WG-TW

Supplying & erecting 5W-7W, 230V integral type LED Lamp suitable for B-22 / E-27 base.

Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

35 W LED Recessed mounted light fixture with Dimmable ballast and complete Accessories.Similar to Model No. RS378B P33 940 PSU-E WB M87+RS378Z M87 D125 R-R FX D

35 W LED Recessed mounted light fixture with ballast and complete Accessories.Similar to Model No. RS378B P33 940 PSU-E WB M87+RS378Z M87 D125 R-R FX D

70 W LED Recessed mounted light fixture with ballast and complete AccessoriesSimilar to Model No. 2x RS378B P33 940 PSU-E WB M87+RS378Z M87 D245X115 S-2R AJ

LED Flexible Strip Lights of lengh of 1.2 meter with required 25-50 mm Aluminum Profile/Housing and Driver 24 W / Meter with Dimmable ballast and complete Accessories.Similar to Model No. SP780 LED22S

LED Flexible Strip Lights with required Flexible Housing and Driver 12 W / Meter with Dimmable ballast and complete Accessories.Similar to Model No. BGC401 1150

LED Flexible Strip Lights with required Flexible Housing and Driver 7 W / Meter with Dimmable ballast and complete Accessories.Similar to Model No. BGC401 550

LED Flexible Strip Lights with required 32-50 mm Aluminum Profile/Housing and Driver 24 W / Meter with Dimmable ballast and complete Accessories.Similar to Model No. SP780 LED22S

Customized Decorative LED Wall Light with ballast and complete Accessories.

Customized Decorative LED Hanging Light with ballast and complete Accessories.

Customized Decorative LED Table/ Floor Lamp with ballast and complete Accessories.

Making suitable size recess in any type of false ceiling for erection of flush type down lighter and finishing the background to match the original surface upto 20W.

Supplying and erecting white footlight with 4 modules concealed modular box and LED lights with cover complete erected on wall /flush to wall with necessary chiselling in wall and finishing with cement and mortar / POP as per required and duly connected.

Supplying and erecting luminous / modular type call bell indicator with plastic body, heavy duty coil and indicator lamp working on 230V A.C. supply with resetting arrangement complete erected on double wooden/ sunmica board.

Supplying and erecting luminous / modular type call bell indicator with plastic body, heavy duty coil and indicator lamp working on 230V A.C. supply with resetting arrangement complete erected on double wooden/ sunmica board.

Supplying & erecting water tight terminal box of 1.6 mm (16 gauge) CRCA sheet of size 150 x 100 x 100 mm complete on pole as per specification No. CBSB

Supplying and erecting midget type 3.0 litres instant type water heater of rustproof & shockproof ABS plastic body, high grade SS inner tank & 3kW heating element with corrosion & hard water protection, with minimum 3 safety protections (i.e. thermostat & thermal cut-out, function valve) complete with 6.5 bar pressure with standing capacity 230/250V, 50Hz, A.C. supply with inlet and outlet, with 3 core PVC flexible copper wire leads duly tested and marking sr. no. and date of erection complete.

Supplying 16 amp. 3 pin plug Top bakelite type of 230 V. A.C. supply.

Providing fiber reinforced PVC flexible pipe upto 1m length with brass locking nuts and washers and clips at both ends suitable for hot water and cold water both (1 set of 2 nos.) complete.

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 300mm. 1400 RPM rust proof body & blades, wire mesh, duly erected,complete.

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control/compatible speed regulator, Temperature Rise of Max. 40 deg. C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF

Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Supplying and erecting marine (Waterproof) plywood 18/19 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wallfasteners, supports, nut bolts etc. complete with compliance to IS 720:2010

Supplying and erecting hylam sheet/ ebonite 6 mm thick for covering wall entries including cutting, drilling and fixing with nut bolts / screws etc. complete.

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP.

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws complete.

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 200 mm width & 100mm height comprising all required standard accessories.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 100 mm height comprising all required standard accessories.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 500 mm width & 100 mm height comprising all required standard accessories.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 150 mm width & 20 mm height complete with necessary hardware.

Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 300 mm width & 20 mm height complete with necessary hardware.

Supplying and erecting PVC slotted box trunking of size 25x25 mm. with accessories on wall/ceiling as per specification No: WG-MA/SLBOX.

Supplying and erecting PVC slotted box trunking of size 45x30 mm. with accessories on wall/ceiling as per specification No: WG-MA/SLBOX.

Supplying and erecting PVC box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX .

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame

Supplying & erecting LED type indicating pilot lamp with LED colours red / yellow / green, 230 / 250V on provided box / panel with necessary material, wiring & connections etc.

Supplying and erecting integrated LED street light fitting 40 to 50W IP65 & IK08 class having single piece pressure die-cast aluminium housing, havingsystem lumens output of Min. 4400 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K,THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG ODF/FLS2.

Supplying and erecting integrated LED Bollard Cylindrical/Cubical shaped 800mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser, having system lumens output of Min. 800 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 25,000 Hrs. at L50B50, including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2.

Supplying & erecting integral post top lantern fixtures (light house type) suitable upto LED 18 W Lamp consisting of combination of spun aluminium canopy & clear acrylic top cover, cast aluminium pole cap on provided pole/ bracket as per specification no. FG-ODF/PTL

Supplying and erecting street light Wall bracket made from 40 mm. dia ‘ G.I. pipe 1.2 m. in total length complete as per specification no. FG-BKT/WB

Supplying & erecting FRP box of size 150mm x 125mm x 100 mm, 2.7 mm thick complete on pole/wall as per specification No. CB-SB

Excavating hard murum / stone metal road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes & clearing the site by removing debris & making the site as required complete.

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 4 ways /12 Poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 8 ways /24 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 12 ways /36 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (36 poles) or TP MCBof 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW SWR/MCBDB1

Supplying, fixing and commissioning 4 pole RCBO 63A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying, fixing and commissioning 4 pole RCBO 6/10/16/20/25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indications per specification no SW-RCCB/RCBO

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, fixing and commissioning 2 pole, RCBO 6/10/16/20/25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erectedon angle iron/GI frame.

Supplying and erecting blanking plate of suitable size on MCBDB.

Providing & erecting 4 Pole MCCB, 415 V, 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying and erecting mains with 4x16 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x10 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 35 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 70 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supply Installation, testing and commissioning of Following Main Panels. Panels shall be fabricated out of 16 SWG CRCA sheet steel, with necessory structural supports in form of structural steel sections. Panels shall be floor mounted.The panel shall be compartmental type with suitable size of bus bar and separate cable and busbarchambers. The cable chambers shall be free from any live open connections. Multifuction meters for all incoming feeders, Indication lamps for all incoming and outgoing feeders for phase identifications and for indication of Switch status.Panel shall be Indoor type1 No. 200 A, FP, Moulded Case Circuit Breaker µP Based O/C, S/C & E/F 35 KA METERING & BUSBARS: a) 1 No's, Multi-Function Meter with I,V,PF,KWH,KW, KVA, KVAR, THD, F with control MCB's, CT's etc. b) TPN, EC Grade Aluminium busbars for 200 Amps insulated with heat shrinkable PVC sleeves c) 1 Sets, RYB, indicating lamps + ON, OFF, TRIP Indication (LED based) with 2A MCB on the incomer 1 Nos. 125 A, TPN, Moulded Case Circuit Breaker with O/C, S/C 35 KA 1 No. 100 A, TPN, Moulded Case Circuit Breaker with O/C, S/C 35 KA 6 Nos. 63 A, FP, Miniature Circuit Breaker 10 KA - C-Curve METERING/Indication : a) 4 Sets, RYB, indicating lamps, ON, OFF, TRIP Indication (LED based) with 2A MCB on the incomer

Supply Installation, testing and commissioning of Following UPS output Panels. Panels shall be fabricated out of 16 SWG CRCA sheet steel, with necessory structural supports in form of structural steel sections. Panels shall be floor mounted.The panel shall be compartmental type with suitable size of bus bar and separate cable and busbarchambers. The cable chambers shall be free from any live open connections. Multifuction meters for all incoming feeders, Indication lamps for all incoming and outgoing feeders for phase identifications and for indication of Switch status.Panel shall be Indoor1 No. 100 A, TPN, Moulded Case Circuit Breaker with O/C, S/C & E/F 25 KA METERING & BUSBARS: a) 1 No's, Multi-Function Meter with I,V,PF,KWH,KW, KVA, KVAR, F with control MCB's, CT's etc. b) TP+2N, EC Grade Copper busbars of 100 Amp, insulated with heat shrinkable PVC sleeves c) 1 Sets, RYB, indicating lamps + ON, OFF, TRIP Indication (LED based) with 2A MCB on the incomer 4 Nos. 63 A, FP, Miniature Circuit Breaker 10 KA - D-Curve 6 Nos. 25 A, DP, Miniature Circuit Breaker 10 KA - D-Curve

Supplying & erecting Aviation obstruction light consisting of yellow painted diecast aluminium alloy housing with Integral LED aviation light comprising ofaluminium housing with polycarbonate enclosure complete.

Supplying, erecting, testing and commissioning of 10kW, 3 x 3.3 KW AC Electric Vehicle charger (suitable for 2/3/4 wheeler) having minimum IK08/IP 54 Protection suitable for three phase, 415V AC, 50Hz incoming and 3 nos. output as per IEC 60309 industrial sockets having capacity of output current of 16A 240V AC at each socket with 3.5"TFT touch screen for human interface & LED Light for status indication and metering for measurement of consumed energy having metering accuracy +/-1%, one hour battery backup for communication, emergency push stop button and having short circuit, over & under voltage, overload, over temperature, earth leakage protection and enclosure made of minimum 1.5mm duly RAL7035 Coated M.S, Erected on iron/GI frame on provided cement concrete foundation complete with one year on site warranty,confirming to IS 17017 Series as per specification.

Providing yearly subscription of payment gateway option for AC/DC EV Charger CMS (Charger management software) system for billing andpayment gateway along with mobile application /android/IOS base app to facilitate charging, CMS should have ISO/IEC 27001:2003 certification.

Supplying, installing, testing and commissioning FR, XLPE armoured cable 4 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Supplying, installing, testing & commissioning push button telephone instrument desk top/wall mount with caller ID & Speaker unit as per specification complete.

Lightening Arrestor Supply, installation, testing and commissioning of 8 mm Aluminum Round Conductor complete as specified in drawing & Meets the requirements of DIN EN 50164-2 (VDE 0185 part 202) & VDE 0185-305 (IS/IEC 62305) ,

Supply, installation, testing and commissioning of Roof conductor holder for parapet- Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance

Supply, installation, testing and commissioning of Polyamide roof cable holder for flat roof: DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance.

Supply, installation, testing and commissioning of Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 16mm rod tapered to 10 mm aluminium rod : Meets the technical specification according to DIN EN 50164- 2 (VDE 0815 part 202). Meets the requirement of VDE0185/305(IS/IEC 62305) 3Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load.

Supply, installation, testing and commissioning of Accessories : System consist of Fang Fix with base and clamp, on the top air terminal is erected. OBO Type No. F- FIX 16 ( 5403 20 0 ). Fang fix clamp made of SS, lightning tested for 100 KA 10/350 micro sec waveform.

Supply, installation, testing and commissioning of 16 KG stone of 365 mm diameter, high level of stability. Quick and easy mounting of interception rod using anchors. Concrete, frost-resistant, can be stacked.

Supply, installation, testing and commissioning of cross universal connector: For T and cross connection, to route vertical down conductor /mesh formation made of hot dipped galvanised iron with necessary screws etc as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts .

Supply, installation, testing and commissioning of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU. OBO Type No. 172 AR ( 5218 92 6 )

Supply, installation, testing and commissioning of Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IS-IEC 62305)(2nos/expansion piece ).

Supplying & erecting street light control panel outdoor type, for three phase 4 wire system having in built astronomical adjustable programmable timerwith minimum 5 years battery back up, having IP54,IK10 protection, 4 pole contactor up to 60A, with maintenance mode to switch ON street lights during time of repairs with energy consumption data recording for analysis and LCD display for energy monitoring with numeric key pad in provided box.

Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC

Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade /SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 200 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting 200 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting 150 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV

Supplying and erecting 200 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV

Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 150 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 200 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Providing coating of bitumen paint & 4mm thick wrapping for underground 150 mm ring main of fire fighting system.

Supplying and erecting M.S./CRCA cabinet for housing Floor Hydrant valve, hose pipe, hose reel and branch pipe (size 1000 x 736 x 736 mm.) made from 16 SWG sheet and angle iron 25 x 25 x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Supplying and erecting 300 mm dia 1.5m in height air vessel / tank fabricated from min 5mm thick M.S. sheet complete as per specification no. FF-FFA/ACT

Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Main Pump:"Supplying, installing, testing and commissioninS with perfect alignin& proper levelling of fire service main Mutti stage -multi outlet pump, of 2850 LPM at 150 m head (Upper) & 90 m (lower) centrifugal type, of suitable HP, 3 phase, 415 volt, 50Hz complete as per specification

Diesel Pump: Supplying and erecting testing, perfect aliSning and proper leveling and commissioninS of horizontal centrifugal Multi stage -multi outlet pump, ot 2850 LPM at 150 m head (Upper) & 90 m (lower) coupled to a diesel Engine of 1800 rpm ,with diesel storage tank (.6x.5x.6 m) 200 ltr capacity includinS first fill of diesel at the time of handover,exhaust chimney,battery backup & accessories as Per sPecifications.

Jockey Pump: Supplying and erecting testing, perfect aligning and proper leveling and commissioninS of Jockey pump Multistage -multl outlet pump, ot L80 LPM at 150 m head (Upper) & 90 m(lower) 3 phase 440 AC, 12 5 HP or of suitable HP with suitable stage as per specillcation

Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 900 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 7.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of cast iron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d)Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/BP

Fire Panel Supplying and erecting testing, perfect aligning and proper leveling and commissioning of Common Auto Control Panel suitable for Auto operation of above 6 pumps. Jockey pump to be auto stan - auto stop and Hydrant, sprinkler and standby diesel pump auto stan - manual stop, Booster pump manual stan - manual stop as per specification. INCOMER: 1 No - 500A FP MP based MCCB, of fault breaking capacity 25 XA (lcs=lcu=1oo% upto 433 V) with R-Y-B & Onlotflltip lampi, ammeter, voltmeter & Load manager. BUSBAR: 500A, 2kA Aluminium Busbar with heat shrinkable sleeves with copper earth bus bar. INCOMMING: 2 Nos. 400A, 4P, 36kA MCCB 1 No. 400A, 4P, Auto Transfer Switch OUTGOING: 2 Nos. 200A, 4P, 25kA, TM MCCB with 180HP Star delta starter Each 2 Nos. 32A, 4P, MCB with 12.5HP Star Delta Starter Each 2 Nos. 32A 4P, MCB with 10 HP DOL Starter Each with on/off/trip indjcation lamps & multifunction meter & E/F protection with with 100 kVAr, 440 V 3 phase, 50 Hz., Contactor Logic & Intelligent Relay micro APFC passive filter panel, consisting of suitable steps of APP/MPP type capacitor units with Detuned (harmonic filter) reactors of suitable rating , APFC panel shall be compliance to IEC 61439 and power quality IEC 61921 standard as per specifications.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with ecessary coupler plates & hardware.

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete.

Supplying, erecting, testing and commissioning 16 HP, VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. celcius and non stop cooling even at 56 deg. celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.CSR No.3-11-6

Supplying, erecting, testing and commissioning 20 HP, VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. celcius and non stop cooling even at 56 deg. celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.CSR No.3-11-8

Supplying, erecting, testing and commissioning 28 HP, VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. celcius and non stop cooling even at 56 deg. celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.CSR No.3-11-12

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.0TR (358 cfm) to 1.25TR (417 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.CSR No.3-11-14

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.3TR (421 cfm) to 1.7TR (586 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.CSR No.3-11-15

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.8TR (594 cfm) to 2.2TR (655 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.CSR No.3-11-16

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 1.0TR ( 441 cfm ) / 1.3TR ( 512 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete.CSR No.3-11-18

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 1.5TR ( 512 cfm ) / 1.8TR ( 618 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete.CSR No.3-11-19

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 2.0TR ( 618 cfm ) / 2.3TR ( 671 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete.CSR No.3-11-20

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 2.6TR ( 918 cfm ) to 2.8TR ( 1100 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete.CSR No.3-11-21

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 3.0TR ( 1100 cfm ) to 3.2TR ( 1165 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete.CSR No.3-11-22

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 1 way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 1.4TR (512 cfm) to 2.0TR (618 cfm) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation complete. CSR No.3-11-34

Supply, installation, testing and commissioning of VRF/VRF based floor/ceiling suspended dual mount type, room/indoor unit (IDU) having nominal cooling capacity of 1.2TR (600 cfm) to 1.5TR(800 cfm) having EER as per BEE standards and specifications with evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, cordless remote control with necessary controls and electrical terminal to receive power supply, etc. IDU should have anti-corrosive coating suitable for coastal area. unit shall be of decorative slim dimension suitable for ceiling suspended having an electronic control console with providing any additional refrigerant and oil charge as per requirement during installation complete. CSR No.3-11-41

Supply, installation, testing and commissioning of VRF/VRF based floor/ceiling suspended dual mount type, room/indoor unit (IDU) having nominal cooling capacity of 2.1TR (800 cfm) to 2.6TR (1000 cfm) having EER as per BEE standards and specifications with evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, cordless remote control with necessary controls and electrical terminal to receive power supply, etc. IDU should have anti-corrosive coating suitable for coastal area. unit shall be of decorative slim dimension suitable for ceiling suspended having an electronic control console with providing any additional refrigerant and oil charge as per requirement during installation complete. CSR No.3-11-42

Supply, installation, testing and commissioning of VRV /VRF based ductable type, high static indoor unit (IDU) having nominal cooling capacity of 5.1TR ( 2040 cfm )to 6.0TR ( 2400 cfm ) having EER as per BEE standards and specifications with evaporator fan with motor, copper tubealuminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control withnecessary controls and electrical terminal to receive power supply, etc. having anti-corrosive coating suitable for coastal area, with suitable ceiling suspension arrangement, with anelectronic control console and any additional refrigerant andoil charge as per requirement during installation connected with the system complete.CSR No.3-11-55

Supply, installation, testing and commissioning of VRV /VRF based ductable type, high static indoor unit (IDU) having nominal cooling capacity of 8.0TR ( 3200 cfm ) having EER as per BEE standards and specifications with evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls and electrical terminal to receive power supply, etc. having anti-corrosive coating suitable for coastal area, with suitable ceiling suspension arrangement, with an electronic control console and any additional refrigerant and oil charge as per requirement during installation connected with the system complete. CSR No.3-11-56

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.0TR to 1.2TR capacity having ISEER minimum 5.00suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. APAC/ WAC CSR No.3-2-9

Supplying, installing, testing & commissioning split type room air conditioning unit 2.5TR to 2.7TR capacity with refrigerant R32 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega split) mounting type complete with temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/WAC CSR No.3-2-15

Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 300 cfm capacity with maintaining the static pressure minimum 20mm suitable to operate on 1 phase, 230V, 50Hz, A.C. supply complete. CSR No.3-11-60

Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 1000 cfm capacity with maintaining the static pressure minimum 20mm suitable to operate on 1ph, 230 V, 50Hz, A.C. supply complete. CSR No.3-11-61

Supply, installation, testing and commissioning air curtain of 6 feet width having air throw velocity of 21 m/sec, low noise level up to 38 to 46 dB suitable for door height upto 9 feet, working on 1ph, 230 V, 50Hz, A.C. supply.CSR No.3-11-76

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.CSR No.3-11-77

Supplying, erecting, testing and commissioning centralised programmable remote contol panel (HMI) touch manager controls minimum 16 system of minimum 64 ODU's can be controlled and up to 992 IDU's can be individually mounted and controlled indoor units having minimum 200 mm size colour LCD touch panel, yearly schedule, power proportional distribution function, temperature limitation, history function complete erected on wall with an arrangement to integrate with provided fire alarm system.CSR No.3-11-79

Supply, installation, testing and commissioning cordlessremote contol having colour LCD panel, real time clock, temperature limitation (16 to 30 degree Cent.), functions like filter clean reminder timer suitable to communicate with wired controller complete. CSR No.3-11-78

Supplying and installation of high pressure grade required size copper connection Y or T- Joints / refnet for liquid and suction line complete erected on wall/ceiling with supports /raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning system. CSR No.3-11-86

Providing vaccumising the airconditioner system to 200 micron and charging with R-410A/R32 refrigerant for air conditioning unit.CSR No.3-10-24

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-89

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-90

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-91

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-92

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-93

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-94

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-95

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-96

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.CSR No.3-11-97

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete CSR No.3-2-26

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete CSR No.3-2-27

Supplying and erecting UPVC reinforced flexible conduit 25 mm in dia. conforming to I.S. with required number of couplings, PVC bushes, check nuts etc. complete.CSR No.1-2-2

Supplying and erecting UPVC reinforced flexible conduit 31/32 mm in dia. conforming to I.S. with required number of couplings, PVC bushes, check nuts etc. complete.CSR No.1-2-3

Supplying and erecting 25/32 mm (ID/OD) Chlorinated polyvinyl chloride pipe (CPVC), thickness 3.2 mm conforming to IS 15778 (CTS Series) with necessary CPVC fittings and solvent cement for Solar Water Heater System as per specification No. ESD-HWP/CPVC CSR No.4-2-19

Supplying and erecting 32/40 mm (ID/OD) Chlorinated polyvinyl chloride pipe (CPVC), thickness 3.8 mm conforming to IS 15778 (CTS Series) with necessary CPVC fittings and solvent cement for Solar Water Heater System as per specification No. ESD-HWP/CPVC CSR No.4-2-20

Supplying and erecting metal work in CRCA sheet with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete.CSR No.6-1-1

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.CSR No.6-1-19

Supplying and erecting GI sheet 0.8 mm (22 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. (PWD CSR 20-21 6-1-3)

Supplying and erecting GI sheet 0.6 mm (24 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. (PWD CSR 20-21 6-1-2)

Supply, installation, testing and commissioning of manually operated, opposed blade, duct mounted, flanged volume control dampers of required sizes in GI construction complete with operating mechanism, mounting arrangement, rubber refrigerant kits etc. complete.CSR No.3-11-80

Supply, installation, testing and commissioning of volume control box with collor for control damper of required sizes in GI construction complete with operating mechanism, mounting arrangement, rubber refrigerant kits etc. complete. 3-11-81 Pg No 76 CSR No.3-11-81

Supply, fabrication, installation an testing of flexible canvass connections constructed between ductable unit / dampers / ducting of required size with fire resist flexible double canvas sleeve complete. 3-11-82 Pg No 76 CSR No.3-11-82

Providing adhesive thermal insulation for supply / return air duct with 19 mm nitrile rubber insulation having R-value as per the prevailing provisions in ECBC- 2007 CSR No.3-11-83

Providing and applying of accoustic insulation for air ducts with 25 mm thick, 48kg/cu.m fiber glass faced with RP tissue and covered with 26 SWG per foratedaluminium sheets complete. CSR No.3-11-84

Supplying & erecting tile type modular diffuser made from aluminium sheet complete with powder coated matching to the ceiling shade for provided suuply and return air. CSR No.3-11-85

Supplying and installing of coller damper of galvanised iron material of upto 120 microns for anti corrosive resistance for supply air grill of required size CSR No.3-11-87

Supplying and erecting aluminium powder coated linear grill of suitable size for width length without collar dampers having matching colour with the existing false ceiling and suitable for deflection of 15/30/45 degree. 3-11-88 Pg No 76 CSR No.3-11-88

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 8 ways /24 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB CSR No.5-4-6

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 12 ways /36 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB CSR No.5-4-6

Supplying, fixing and commissioning 4 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO CSR No.5-6-13

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB CSR No.5-3-2

Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB CSR No.5-3-10

Supplying, erecting & marking FPMCB 40A to 63A inprovided distribution board as per specification no. SWSWR/MCB CSR No.5-3-12

Supplying, erecting & terminating XLPE armoured cable 4 core 6 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR No.7-2-32

Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR No.7-2-33

Supplying, erecting & terminating XLPE armoured cable 4 core 16 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR No. CSR No.7-2-34

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV CSR No.1-3-15

Supplying and erecting PVC insulated PVC round sheathed 1 sq.mm (32 no. x 0.20mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 Kv CSR No.1-3-14

Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW CSR No.1-3-1

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW CSR No.1-3-6

Supplying & erecting HMS P.V.C. conduit 25 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. CSR No.1-1-9

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware. CSR No.7-11-6

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 200 mm width & 75 mm height complete with necessary coupler plates & hardware. CSR No.7-11-7

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware. CSR No.7-11-8

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware CSR No.7-11-10

Supplying and erecting minimum Three & above star rated submersible pump set of 5.625 KW/7.5 HP with 415 V, 50 c/s AC supply suitable for 150 mm dia. borewell suitable for 60 to 300 LPM discharge at 257 to 15 m head & discharge & delivery pipe of Size-50 mm diameter with a necessary H type clamps as per specification No. WP-SMP

Supplying & erecting Dewatering Monoblock pump set 415V, 3 phase, 50C/s, A.C. supply of 2.25KW/ 3 H.P., of 12 to 26 m head with 560 to 70 LPM discharge, 10.5mm Solid Handling Capacity, non clogging minimised abrasive wear, large impeller clearance & maintenance free pump set with water proof cable duly sealed with epoxy material built in protection to prevent the motor from burn out due to abnormal operation. specially designed high efficiency motor with F class insulation & the pump mechanically sealed in the oil chamber,. etc. complete as per specification no. DWP- SMP

Supplying & erecting flat flexible 3 core 4 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Supplying & erecting Water level controller 230/415 V, A.C. , Four way under ground & Over head tank operation only.

Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.C. Submersible/centrifugal pump set up to 7.5 HP - 10 H.P. consisting of DOL starter having relay range 13-21 AMP,S.P.P., Combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc.

Supplying, fixing and commissioning MCB type change over switch 4 pole, 40A with 3 positions (I-O-II) with centre off position as per specification no. SW-SWR / MCBCOS

Supplying and erecting plywood 12 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners supports, nuts bolts etc. complete.

Supplying and erecting non return valve 50 mm dia in position made of gun metal complete.

Supplying and erecting 50 mm dia. gun metal sluice valve at position with necessary materials complete.

Supplying and erecting ISI mark GI pipe 50 mm. dia. ‘B’ class at position with accessories complete as per specification no. CW-PLB/GP.

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying, installing, testing and commissioning FR, XLPE armoured cable 4 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

DGset Supplying, erecting, testing and commissioning of diesel generating set with alternator of 500 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2 and maximum fuel consumption 81.90 Ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete setenclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 690 Ltr etc. on provided M20 Grade CC Foundation and obtaining necessary approval from Electrical Inspector as per specification no. GEN-DG

Cement : Standard Consistancy, Fineness, Specific Gravity, Setting Time (Initial & Final), Compressive Strength, Soundness.

Crushed Metal : Water Absorption, Specific Gravity,Impact Value, Crushing Value

Crushed Metal : Sieve Analysis

Crushed Metal : Abrasion Value

Crushed Metal : Flakiness Index & Elongation Index

Bricks Water Absorption (Set of 5 Bricks), Compressive Strength( Set of 5 Bricks), Efflorescence (Set of 5 Bricks).

FLOORING TILES (MOSSAIC / CEMENT) Flooring of Natural Stone (Kota,Marble, Granite,Tandur.etc.) Water absorption, Specific gravity

CONCRETE Compressive Strength OF C.C. Cube (Set of 3 cubes).

CONCRETE Concrete Mix Design (With all Tests on basic materials)

CONCRETE PAVING BLOCKS Compressive Strength , Water Absorption,(Set of 8 Blocks)

STONE/ RUBBLE Crushing Value/Compressive Strength, Water Absorption &Specific Gravity,

SOIL / MURUM Sieve Analysis.

STEEL (Tensile strength, %, Elongation, Yield Stress,Weight-Per Meter, Bend / Rebend Test, Proof Stress.)

SAND Fineness Modulus ( Sieve Analysis ),Silt & Clay Content

Royalty charges for Sand are to be paid to the Contractor after producing receipt of royalty paid to the Govt. for the material used for this work.

Royalty charges for Other Material to be paid to the Contractor after producing receipt of royalty paid to the Govt. for the material used for this work.

S.S.SATHE