PROVISION OF TOILET BLOCK NEAR BUILDING NO CB 05 AND CONSTRUCTION OF STORE ROOM NEAR BUILDING NO CB 04 AT INF SCHOOL UNDER GE MIS MHOW

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in Hard / Dense soil complete all as specified

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cespits, manholes etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in Hard / dense soil complete all as specified

Excavating over areas n.exc 1.5 m deep and getting out in hard / dense soil complete all as specified

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filing,sub base of floor etc complete all as specified

M&L for Damp proof course 40mm thick in cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate mixed with WPC @ 2% wt of cement ,on horizontal or vertical surfaces including necessary formwork complete all as specified Note : WPC will be measured and paid seperately.

M & L for high strength steel deformed TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia, etc complete all as specified.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in strriups,spaces,nibs and binders complete all as specified.

Returning, filling in, soil including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete.

Returning, filling in, soil including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6.00m mean radius built in cement mortor 1:6 complete all as specified

M&L for brick work with sub class 'B' modular bricks, straight or curved on plan to any radius built in CM 1:4 as in half brick thick wall complete all as specified

S&F Rolled mild steel joist,fFlats,channel, angle, square Bar as in window grills and steel racks and conforming IS-1161-1979 grade ST-240 complete all as specified Note: Design and Drawing of Window Grill and Steel Racks shall be provided during execution of work by Engineer in Charge as per site requirement.

M & L for for use and waste of formwork to sides and soffits of floor or roof beam, beam hauchings, bands, girders, bressummers, lintels, etc for fair finished surface of concrete complete all as specified.

M&L for RCC M-25 grade concrete (Design Mix) using 20 mm graded stone aggregate as in beams, bands, cantilvers, bressummers, linters, chajjas, over 1.5m span complete all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for RCC M-25 grage concrete (Design Mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, etc complete all as specified. NOTE : Reinforcement shall be measured and paid separately under relevant item.

M&L for use and waste of formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) etc for rough finished surface of concrete ecomplete all as specified

M&L for Moorum/red bajri filling in floors or pavings, laid in layers not exceeding. 15 cm thick, spread, levelled and rammed including watering as required complete all as specified.

M&L for hardcore with broken stone of gauge n exc. 63 mm deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified

M & L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate for levelling course in floors complete all as specified.

M & L for 75mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in floor/ plinth protection finish the surface even and smooth with using extra cement including filling the expansion joints with bitumen filler / filler boards and necessary form work etc complete all as specified.

M&L for rendering 10mm thick cement plaster in CM 1:6 on other than fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified

M&L for rendering 15mm thick cement plaster in CM 1:4 on fair faces of brick or concrete surface mixed with liquid water proofing compound @ 200 ml per bag finished even and fair without using extra cement complete all as specified

M&L for applying two coats of superior quality oil emulsion distember over a coat putty including preparation of surface complete all as specified Note:- Putty shall be measured and paid seperately under relevent item

M&L for preparation of new plastered surfaces of walls and applying two coats of Acrylic Smooth exterior paint of required shade (@ 1.67 litre /10 sqm) over a coat of primer(@ 2.20 kg/10 sqm) of same make base over a coat of putty all as specified Note:- Putty shall be measured and paid seperately under relevant item

M&L for preparation of new plaster surface of wall and applying 2mm thick cement base wall care putty in two coats (each coat not less than 1mm) over a coat of primer , surface finished even and smooth with sand paper complete all as specified

S&F PVC (SWR) pipes 150mm bore single socketed in any length half cut to use as valley gutter with and including proper fixing arrangement of mild steel strap as required at site complete all as specified

S&F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed / Glass and one shutter wire mesh) with following specification complete all as specified and as directed by Engineer-in-charge. (i) Windows frame of cross section 101mm x 44mm (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm (iii) Sliding shutter frame of cross section 40 x 18mm (iv) 4 mm thick glass superior quality. (Min) (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 No. (Min) (vii) Sliding rollers per shutter - 02 Nos. (Min) (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 No. Note-:(a) Thickness of Aluminium Section shall be minimum 2 to 3mm 2.Drawing and size of Window shall be provided by Engineer- in -Charge as per site requirement.

S&F powder coated aluminum door with the following specification and making good the adjacent surfaces, complete all as specified and as directed. (a) Cross section of chowkhat frame 101.60x44.45.mm (b) Cross section of hanging and meeting style 83x44mm (c) Top rail of cross section 114x44mm (d) Bottom rail of cross section 114x44 mm (e) Locking rail (middle rail) of cross section 83x44mm. (f) 4 mm thick glass superior quality. (Min) (g) Aluminum handle eisc type -02 Nos per shutter (inside & out side). (h) Aluminum door stopper heavy duty-01 No per shutter. (i) Aluminum tower bolt 200mm long-01 No per shutter (inside). (j) Concealed Lock with key superior quality make and type as approved by GE openable both from inside & out side -01 No per shutter. Note- 1.Thickness of Aluminium Section shall be minimum 3 mm thick 2.Drawing of Door size and details shall be provided by Engineer- in- Charge as per site requirement.

S&F fabricating coloured powder coated aluminium frame work for door shutter ,windows , ventilators, partitions with one or more rebates sections of approved tint as required for partitions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified

S&F aluminium coloured power coated Partition/ window / ventilator shutters, sliding type without sash bar aluminium section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised alu snap beading screws etc complete all as specified

S&F 4.8 mm thick plain or tinted glass, ordinary quality including rubber gasket for packing and fixed to aluminium doors / window /partition including necessary cutting / moulding and chamferrring of edges for service window counters complete all as specified

S&F aluminium (extructed section) door closer hydraulically regulated, desingnatin No. 3, universal type, suitable for door shutter and fixed complete all as specified

S&F 12mm thick frosted toughned glass door shutter fixed on patch hinges / pivot including stainless steel handle of 12 inches long,mortice locking arrangement and floor Spring (Make-Hardwyn ) complete all as specified and as directed. Note: Logo of required design/Shape/Size shall be embossed on Door Glass as per user requirement and quoted rate shall be inclusive for the same.

M&L for Machine cut Kota stone slab flooring 20 mm thick (+ 2mm) thick of 58cm x 58cm in size (or nearest size as available in the market) laid over and including 15mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing to mirror finish complete all as specified

All as per item No 34 above but as in skirting/ dado etc with and including 10mm thik backing coat in cement mortar 1:4 an wall complete all as specified

M&L for scratch free Glazed (Porcelain) Vitrified Tiles (GVT)/Polished Glazed Vitrified Tiles(PGVT) 9mm-10mm thick (square or rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.74 sqm ie size 600x1200 in floors set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed in CM 1:6 complete all as specified Note : (a) Size and pattern /Texture of GVT(Matt Finish) /PGVT(Glossy Finish) shall be approved GE 2.Glazed Coating on GVT/PGVT shall not be less than 1mm. 3.Colour of epoxy material between tiles and spacing of spacer between Tiles shall be approved by GE

All as per item No 36 above but as in skirting/ dado with and including 10mm thik backing coat in cement mortar 1:4 on wall complete all as specified

S&F pre-colour pre- profiled (Galvalume/zinkalume) sheets AZ 150 0.50mm thick (including coated thickness) of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 as in frame work for sun shade, roof projection and vertical section etc. complete all as specified

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

Demolition of Stone slabs and tiles of any description or thickness in floors complete all as specified

M&L for machine pressed rubber moulded coloured precast concrete interlocking paver block (glossy finished) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25mm thick bedding layer of stone dust and joint filled with sand including locking of sides with PCC 1:3:6 type C1 complete all as specified

S&F Plain, galvanised, mild steel sheeting 0.63 mm thickness as in ridges,hips, valley gutters on roof,with grade of zinc coating 275 with all fixing arrangement complete as specified.

S&F Anodised aluminium snap grid frame work of size 605mmx605mm for false ceiling with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

S&F Exposed metal frame ceiling with 6mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid complete all as specified.Note:Frame work for ceiling shall be measured and paid separately under relevant item

S&F PVC false ceiling consisting of 5 to 10mm thick Plain colour PVC sheet hollow section inclusive of required frame work and other fixing arrangement like screw as per specifications and drawing,complete all as specified and directed.Note: Cross section,Size,Thickness of PVC Panel shall be approved by Engineer-in- Charge as per site requirement

S & F Mild steel, plain black sheet 2mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, but in hearths; covering to door shutters; covering to door chowkats (frames);chullah hoods; water tanks; water troughs;ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched;including round headed screws, clout nails or rivets and fixed to wood or steel members, etc.,with plain 40 mm lap joints or welded/ riveted seams including bending, turning up,mitred angles, stopped ends, outlets, etc. as required complete all as spd and directed.

S & F Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing, Fe 410-W (Gde-E-250) quality-A,etc complete all as specified

S&F factory made single side prelam PVC sheet door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet reinforced with ms square tube, & edges will be painted to match with prelam sheet complete all as specified and as directed.

S&F for factory made Single Side Prelam PVC door shutter 30mm thick (style) consisting of frame made out of ms tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and Single Side Prelam PVC sheet for top rail, lock rail & bottom rail. Panelling of Single Side Prelam PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and as directed.

S & F factory made 25 mm thick 100% solid WPC (wood polymer composite) laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 ( suspension grade), Calcium carbonate and natural fibers ( Wood powders / rice husk/wheat husk) and non toxic additives made from extension process WPC foam sheet single extruded (Inner) with having minimum density not less than 650 kg kg/cbm, an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of 200 N (Face) & 1100 N (Edge) minimum compissive of 50N/mm2 Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category property of being Termite/ borer free, water/ moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In- charge,Material test certificate and authentication should be compulsory provided by the manufacturing company, complete all as specified and as directed.

S & F factory made 100% solid WPC (Wood polymer composite) Door frame 90mm X 45mm (Moulded) single rebated made from wood polymer composite (single extruded process material comparison of virgin PVC polymer of k value 57-60 (Suspension grade), calcium carbonate and natural fibers (Wood powder/rice husk/wheat husk) and Non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treaded star headed screws having minimum frame density of 750 kg/ cbm, an ISO 9001-2015 certified company, having good screw holding capacity (screw withdrawal strength of (Min 990 N ), minimum compressive strength of 58n/mm2, Modulus of elasticity 900N mm2 and resistance to spread of flame of class A category with property of being Termite/borer proof, water/ moisture proof and fire retardant & fixed with position with SS dash fasteners / Hold fast of required dia and length, all as per specifications drawings as directed by the Engineer-In-charge,Material test certificate and authentication should be compulsory provided by the manufacturing company including hold fast or fasteners, complete all as specified and as directed.

M&L for Non Skid ceramic coloured tiles (Matt/Gloss Finish) of size 400x400x7 mm thick in floors set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed in CM 1: 6 complete all as specified

M&L for glazed ceramic coloured tiles (Matt/Gloss Finish) of size not less than 450x300x7 mm thick as on vertical surfaces such as wall set and jointed in neat cement slurry and pointed with coloured cement to match over and including15 mm thick backing coat on fair faces of brick work in CM 1:4 complete all as specified Note:. Pattern /Texture tile shall be approved by Engineer-in - charge.

M&L for 18-20 mm thick Black granite slab of approved quality of any size bedded and jointed in grey cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite stone laid over and including 15 mm thick screed bed in CM 1:4 including polishing done by mechanical grinder and moulding edges complete all as specified

S& F Rotational moulded Polyethylene water storage tank 1000 liters capacity (cylidrical vertical with closed top) double layered hoisted and fixed in position all as specified in SSR part I complete all as specified

S&F 15mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc ,complete all as specified

All as per item no 58 above but 20mm bore

S&F CP pillar taps (swan neck type) cast copper alloy CP with capstan head, screwed down ,high pressure with long screwed shanks and fly nuts fixed in 15 mm bore pipes complete all as specified

S&F CP angle stop cock of 15mm bore screwed down for high pressure with crutch or butter fly handle ,screwed both end for iron pipes complete all as specified .

S&F fancy type chromium plated15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified

S& F CP toilet paper holder

S&F Vitreous china wash down water closet pan ( Pedestal pattern), white (excluding ,flushing cistern and flush pipe) including connection to drain (out going pipe) "P' or 'S' trap, flush pipe, antisyphonage pipe etc complete all as specified and directed

S&F vitreous china squatting pan `Orissa ' pattern of size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipes) including connection to trap and to flush pipe etc and lime concrete bedding , 'P' or 'S' trap complete all as specified

S&F PVC valve less,syphonic action type flushing cistern,low level ,10 litres capacity white with inlet ball valve,float and handle including brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified

S&F health faucet with flexible pipe of one meter length including wall hook for EWC complete all as specified

S&F vitreous china wash basin white (table top) of size 490x400x145mm including 32mm brass CP waste coupling complete all as specified .Make:Plumber Cat Part No.- PBW-CTB-2315

S&F Vitreous China Urinal, Half stall type,white with grating and union for discharge pipe, urinal spreader with waste pipe and all fiting for urinal.complete all as specified

S&F PVC (SWR) floor trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified

S&F PVC connection 15mm size with PTMT nuts of length 450 mm long

S&F PVC waste pipe for urinal / wash basin / sink pipe 32mm bore 65cm long

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipes and fixed. ( Minimum Weight 210 gms)

M&L for salt glazed stoneware drain pipe of 150mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under and haunching against the sides of pipe after they are laid and tested internal dia of pipe 150mm complete all as specified

M&L for RCC type 1:2:4 type B1 using 20 mm graded granite stone aggregate) as in precast cover slab for manholes and soak well cover slab etc set in cement mortar (1:4) etc with and including necessary form work all as specified . Note:- Reinforcement shall be measured & paid separately under relevant item.

M&L for plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in foundations, filling and mass-concrete complete all as specified

M&L for PCC 1:2:4 type B1 using 20mm graded aggregate as in coping including necesarry form works complete all as specified

S&F PVC ( SWR) bends any radius bore of 150 mm

S&F PVC ceiling lining (False Ceiling) consisting of 5mm thick Plain colour PVC sheet 8 to 10 mm hollow section inclusive of solvent cement and fixing at site on frame work as per requirement on site complete all as specified

E/M PORTION

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI /PVC casing capping as required at site marked inclusive of tees ,bend ,elbows etc upto and including modular sunken anodised steel box for housing modular switch socket , regulator etc including modular cover plate and cover frame of any module ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified for the following

One light/fan point controlled by one switch

One Exhaust fan point controlled by one switch

One 5amps socket out let point controlled by one switch on same board with other switches.

One 5amps socket out let point on independent board controlled by one switch.

All as per item No 82 above but using PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

S&F Switch Piano type single pole 5 amp, 230 Volts

S&F Switch Piano type single pole 5/15 amp, 230 Volts

S&F socket outlet 2 in 1 , 5 pin, 5 amp, 230 Volts

S&F socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts

S&F Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting

S&F LED ceiling light fittings 34/36 watt recess mounting type 2'x2' luminaire, 6000k complete with driver duly connection wire etc complete Make :Jaguar Cat No. LSVR01S036XC, Crompton Cat No. LCTLRN-36-FO-CDL, Bajaj Cat Pt No. BZRSQL 36W GZ1 WH or equivalent in Havells /Wipro.

S&F integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH or equivalent in Wipro

S&F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe 40 mm dia medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Cat No ENXT P 36L WH CR PC SD of Bajaj or equivalent make in Philips, Wipro/Havells

M&L for Sub main wiring in repairs with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25/32 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FR LS 6.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge.- Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

S&F double door DB TPN 4 way powder coated suitable for fixing MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified

S&F double door DB SPN 8 way powder coated suitable for fixing MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified

S&F MCB TPN 40 to 100 amps 10 KA, c-series including connection with suitable size aluminium/copper lugs complete all as specified

S & F MCB SPN 6 to 32 amps 10 KA, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified

S&F fix exhaust fan , steel body AC single phase, 230 V of size 300 mm sweep ventil air DSP green type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall or fixing in aluminium fabricated windows including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and including making suitable size of hole to existing brick wall for mounting fan base and making good the same as per existing compelte all as specified

M&L for Earthing complete with galvanisedsteel earth plate electrode60×60cm.× 6mm thick, buried directly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normalground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, checknuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion.Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 12.5 m from earth plate shall deemed to be included in quoted rate .

S&F integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified .Make:- Havells Cat No. LHEXBLP7IN1W009 ,Bajaj Cat Pt No. BCLSB 10 WH or other equivalent in Wipro

S&F LED street light fittings 1x30 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed .Make:- Havells Cat No.LHEXAYP7PN6K030 Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. BCLST 25W LED IV2

S&F MCB TPN 32 amps 10 KA, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified

S&F energy efficient exhaust fan of metal body 225/230 mm sweep Ventil Air -DSP green type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall or fixing in aluminium fabricated windows including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified

S&F LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches / ducts, on poles of size 4 core x 16 Sqmm including testing commissioning complete all as specified

M&L for sand cushioning with dry and clean sand over and under the under ground cable in trenches , ducts for cable protection complete all as specified.

Supplying and laying reinforced precast concrete cable cover, class LV, type 1 flat of size 250mm x 150mm x 40mm complete all as specified

Supply and laying galvanised iron pipe 'light Grade' 40 mm dia in trenches , under floors, roads, along poles for protection of cables with all necessary fittings, including sealing ends complete all as specified

BHATIA ASSOCIATES

M/S DADISA CONSTRUCTION

M/S Sunshine Construction

M/S UnitedConstruction

sunway associates