Construction of Didi Kitchen Canteen in the Campus of FFP Building at HEC, Dhurwa, Ranchi

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqmm plan) including dressing of sides and ramming of bottoms, lift up to 1.5m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Filling in foundation trench and plinth in layer not exceeding 150mm thick well water , rammed …. direction of E/I (mode of measurement compacted vloume )

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

0.63 mm thick with zinc coating not less than 275 gm/m²

Labour for fitting and fixing G.C.I. Or C.A. Sheet roofing in proper slope including the cost of "J" or "L" hooks, limpet and bitumen washers, carriage of sheet to work site, and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one side teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)

Providing one coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge.

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Size of Tile 800x800 mm

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Size of Tile 800x800 mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer?in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Stainless steel kitchen sink - with drain board bowl depth 250 mm Stainle

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.

Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :

4.0 mm thick glass panes

Carriage of Materials

Sand Lead 8 km

Bricks Lead 8km

Stone chips 22 km

Local Sand-3km

Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350 gms.) with extra socket all compere as per specification and direction of E/I.

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.

Vertical -25mm dia

Vertical -32mm dia

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror - 450mm x 300mm

C.P. brass soap dish container medium quality with screw and hinges etc.

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing PTMT grating of approved quality and colour.

Circular type - 100mm dia

Supplying fitting & fixing special type of C.P. Bath room fittings for V.I.P. buildings (JAL, Jaquar, Marc or equivalent mark)

Angular stop cock (Long Thread)

Providing and fixing on wall face unplasticied Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion (i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door

Single tee without door

75 mm bend

110 mm bend

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

Group-C

Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size of GI box etc as required.

Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire(for Single Separate 5A from nearest switch board )

2x2.5 Sqmm + 1x2.5 sqmm earth wire (for switch board circuit to LDB).

2x4.0 Sq.mm + 1x4.0 Sq.mm earth wire.(16A Sockets near indoor Unit of Split AC & AC Starter for AC in switch board and Geyzer)

4x6 Sqmm +2x6 sqmm earth wire.(to be used for all LDB)

4x10 Sqmm +2x10 sqmm earth wire.(to be used for all PDB)

1 x 1.5 sq.mm

Supply and drawing of co-axial TV Cable RG-6 grade, 0.7 mm. Solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed conduit PVC as required. Make:- Finolex / Batra Henley / Lapp

S/F PVC Conduit: Supplying and fixing of following sizes of Rigid 2 mm thick PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for TV and TEL out lets.

S/F Modular type Switch / Socket:- Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. (to be used in switch board with sockets)

5/6 amps, one way modular switch

15/16 amps, one way modular Switch for 2 Nos. 6 A shockets near table.

5/6 amps, 3 pin modular socket

15/16 amps, 6 pin modular socket for indoor Unit of Split AC

S/F Modular type electronic fan regulator:- Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

S/F Modular blanking plate:- Supplying and fixing of the existing modular plate and switch box excluding modular plate etc, as required.

S/F Modular boxes, base and cover plate:-

Supplying and fixing following size /modules G.I. box along with modular base and cover plate for modular switches in recess etc. as required Make:- Legrand/Schneider/MK Blenz.

1 or 2 modules (78mmx78mmx45mm)

4 or 5 modules (78mmx140mmx50mm)

S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Batten / Angle Holder:- Supplying and fixing batten / angle holder including connection etc as required.

S/F Extra Down Rod:- Providing and fixing extra conduit down rod of 20 mm dia, 2x10 cm, length with 2x1.5 Sq.mm FR PVC insulated copper conductor, single core cable including painting etc. as required. (Note more than 5 Cm. length shall be rounded to the nearest 1) (Extra Down Rod For Ceiling Fan)

ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.

S/F SP MCB DB:- Supplying and fixing following way, SP&N MCB distribution board of sheet steel for 240 Volts on surface /recess complete with tinned copper bus bar, neutral busbar, earth bar, detachable gland plate, interconnections, phophatized and powder coated painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR).

8Way Double Door.

12Way Double Door.

16Way Double Door.

S/F TP MCB DB: Supplying and fixing following way,three pole and neutral sheet MCB distribution board, 415 volts on surface/recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections,phosphatised and powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR).

4 ways (4+12) Double Door. (horizontal type)

6 ways (4+18) Double Door. (horizontal type)

S/F 'C' series MCB:- Supplying and fixing 240/415 V, 10 kA, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32A Single Pole

6-32 A DP MCB

6-32A TPN MCB (To use as incomer for all LDB)

50/63A TPN (To use as incommer for all TPN D.B.)

S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Batten / Angle Holder:- Supplying and fixing batten / angle holder including connection etc as required.

S/L 6 SWG G.I. Wire :- Supplying and laying of 6 SWG G. I. Wire at 0.50 Mtrs. Below ground level or along the wall for conductor earth electrode, including soldering etc, as required.(for running earthing DB to Panel)

P/F 25 x 5mm G.I. earth strip in surface/recess :- Providing and fixing 25mmx5mm G.I. earth strip in surface /recess for connections etc. as required and making the earth grid for all G.I. Earthing pits of the building.

S/L 6 SWG G.I. Wire :- Supplying and laying of 6 SWG G. I. Wire at 0.50 Mtrs. Below ground level or along the wall for conductor earth electrode, including soldering etc, as required.(for running earthing DB to Panel)

P/F 25 x 5mm G.I. earth strip in surface/recess :- Providing and fixing 25mmx5mm G.I. earth strip in surface /recess for connections etc. as required and making the earth grid for all G.I. Earthing pits of the building.

Providing and fixing of PVC/XLPE indulated PVC sheathed heavy duty, aluminium armoured cable of grade 1.1KV as per IS 1554 (Part-1), etc. as required. Make:- Havells / Finolex / Polycab/ KEI.

2 Core 6 Sq. mm XLPE Al. Ar. Cable 1.1kV.

2 Core 10 Sq. mm XLPE Al. Ar. Cable 1.1kV.

3.5 Core 25 Sq.mm. XLPE Al. Ar. Cable 1.1kV.

3.5 Core 35 Sq.mm. XLPE Al. Ar. Cable 1.1kV.

4 Core 10 Sq. mm XLPE Al. Ar. Cable 1.1kV.

69 MV Cable Laying up to 25 sq. mm. in ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq.mm. direct in ground including excavation, sand cushioning, protective coveringand refilling the trench etc as required.

1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

2 Core 6 Sq. mm 1.1kV (19mm)

2 Core 10 Sq. mm 1.1kV (19mm)

4 Core 10 Sq. mm 1.1kV (19mm)

3.5 Core 25 Sq. mm. (28mm)

3.5 Core 35 Sq. mm. (32mm)

S.I.T.C of flowing ratting LEDStreet lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection ) in existing pole /pipe for supply voltage 100-270V AC ,50Hz .Luminarie shall be confirm to IS : :10322 part-5 /section -3 and shall be complete with all necessary accessories as required.

25W LED STREET LIGHT

20/22W LED TUBE LIGHT

supply installation ,testing and commissioning of folowing size ceilling fan 3 blades confirming to is : 374:2019 including wiring the down rods of standard length (upto 30cm) with 1.5sq mm fr pvc insulated ,copper wire suitable for 230v 50hz ,single phase supply etc ,complete as required .

1400mm (56") BLDC 5star rating 32W ceiling fan

S.I.T.C of flowing ratting recess /surface mounting LED round /square shape Down light luminarie with pressure die cast housing for single phase supply voltage .Luminarie shall be confirm to IS :10322 part-5 /section -2 or IEC :62722 with all necessary accessories as required.

12W LED Round Down light

15/16 W LED Round Down light

2x8w Led outdoor Up-down light with ip:65 protection die cast aluminium housing

LED strip light 24volts DC with IP:65 rated in different colours of lenth 5mtr and power 5w per mtr including driver 1s:10322 part 5/ section 7

Providing & fixing of modular kitchen cup board 19mm thick BWP board of national make of eqivalent on front top side with rack 1.5mm thick liminated 2'0"X1'9"X0'9" steel rock hing bocket with teak wood beads and copping … do … all as per building specification and direction of E/I.

Supply fitting & fixing upper cabinet cost over 19mm thick BWP black board of national make or equivalent and 1st quality laminate of century or equivalent on front and side with rack including teak wood beats and leaping beats costs cover glossy polish on all side including the primer putty lock etc all complete as per direction of E/I

Supply fitting & fixing Wall Paneling With 1mm laminate do complete job.

Supply fitting & fixing Door Frame & choukhat Paneling With 1mm laminate do complete job.

Supply and fixing Chair do complete job

Supply and fixing Dinnig Table

Supply and fixing Sota 9 seeter

Supply and fixing Sota1 seeter

Supply and fixing CENTER TABLE Rectangular CENTRE TABLE with Other wood Top of 800mmX550mm

Supply and fixing Reception table

Supply and fixing roller blind

Supply Fitting and fixing of Table Top Basin in the direction of E/I make JAQUAR

Supply Fitting and fixing of Pillar Cock With Extention body in the direction of E/I make JAQUAR

Supply Fitting and fixing of Wall Hung WC with seat cover in the direction of E/I make JAQUAR

Supply Fitting and fixing of 2 way bib cock in the direction of E/I make JAQUAR

Supply Fitting and fixing of Urinal in the direction of E/I make JAQUAR

Supply Fitting and fixing of Sensor mini concealed type fluse urinal in the direction of E/I make JAQUAR

Supply Fitting and fixing of soap dispensor in the direction of E/I make JAQUAR

Supply Fitting and fixing of botel trap in the direction of E/I make JAQUAR

Supply Fitting and fixing of hand dryer in the direction of E/I make JAQUAR

Supply Fitting and fixing of Concealed cistern in the direction of E/I make JAQUAR

Supply Fitting and fixing of Control plAte in the direction of E/I make JAQUAR

Supply Fitting and fixing of heath faucet in the direction of E/I make JAQUAR

Supply Fitting and fixing of paper holder in the direction of E/I make JAQUAR

Add 18 % GST (in Basic Rate must fill 18)

Add 1% Labour Cess (in Basic Rate must fill 1)

MAHALAXMI CONSTRUCTION

MANJEET KUMAR