Mandapali to Mundiguda_Road_Pot hole repair, Berm work and Road furnitute,bush cutting _0.000 to 1.350

Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per MoRD Specification for Rural roads Clause 201 by manual means as per the direction of the Engineer in charge.

Cleaning the existing Black topped surface with removal of foreign materials with brooms or soft brushes and finally dusting with old gunny bages and/or compressed air to receive bituminous etc complete as per direction of EIC.

Providing, laying, spreading and compacting stone aggregate specific size to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel roller 8-10 tonnes in stages to proper grade and camber the voids with small stones and hand packing the same to proper camber, applying and brooming requsite type of screening / binding materials filling up interstices of coarse agreegate, watering and compacting to the required density as per clause 404 of MoSRT&H specification for road and bridge work etc all complete including cost, conveyance, royalty and taxes of all materials with all labour and T & P etc complete. WBM GR-III

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness using 0.27cum of 13.2 mm to 5.6 mm aggregates using S-60/70 penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type C as per Technical Specification Clause 508 of MoRD including cost, lead, lift royality and taxes of all materials required for the work by manual means etc. complete and as per direction of the Engineer -in- charge.

Providing 6 mm thick pre coated seal coating including cost, conveyance, royalty & taxes of all materials including hire & running charges of P.R .R etc complete

Providing & applying primer coat with Bitumen emulsion on prepaired sueface of granular base including cleaning the road surface and spraying primer @ 0.60kg / sqm using mechanical means as per clause 502 of MoSRT & H specification for road & bridge works etc complete as per direction of EIC..

Providing & applying tack coat with Bitumen emulsion using emulsion pressere distributer @0.20kg / sqm on the prepared bituminous / granular suerface cleaned with mechanical broom as per clause 503 of MoSRT & H specification for road & bridge works.

Construction of enbankment with approved material obtained from borrow pit with lead and lift transporting to site by mechanical means within lead of 5kms, spreading grading to required slope and compacting to meet requirement of table 300-2 and clause 305 of MoSRT&H specification for road and bridge works etc complete as per direction of EIC.

Finishing Wall with Water Proofing Cement paint Two coat over a coat of cement wash of approved shade on new work including all cost of cement paint etc, Complete.

Providing and fixing of typical informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause Annexure 300,800,1700 of MORD as per direction of the Engineer in charge