REPAIR MAINT TO BARBED WIRE FENCING CHAIN LINK FENCING GATES GATE PILLARS PCC COPING JAFFARI WALL AND OTHER MISC B AND R WORKS

Amount

SCHEDULE A BOQ

Dismantling fencing wire mesh, barbed wire any type and any size complete all as specified and as directed. Note: The unit rate quoted is deemed to included for Removing of accumulated earth of any width and depth upto 15 cm cleaning/cutting the grass/ trimming down shurbs/ branches/ small trees with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from fencing post in outside MD land

Excavating in post holes (or similar holes) in any type of soil, each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

M&L M S angle iron Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 including dismantling posts or struts (wood, steel or RCC) any section, complete all as specified and as directed.

M&L Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, n exc 5cm long diameter of neck 5 to 10mm including taking down existing one complete all as specified and as directed.

M&L PCC 1:4:8, type D-2, using 40mm graded stone aggregate in foundation filling and mass concrete etc complete all as specified and as directed.

M&L Plain Cement concrete 1:3:6,type C-1, (using 20mm graded crushed stone aggregate) as in foundation of fencing post, filling and mass concrete etc complete all as specified and as directed.

M&L Straining and fixing only chain link fencing including line wires, any mesh size and type of to any type of standards, rails, straining bolts etc inclunding provision 10mm dia MS bars as line wire welded to fencing posts and MS flat iron for fixing fencing wire mesh complete all as specified and as directed. Note : Supply only chain link mesh and 10mm dia round bars will be measured and paid separately vide item No 9&10 here in below. However, cost of labour for fixing is deemed to be included in the unit rate quoted against this item.

Supply only Chain link mesh, made of galvanised wire and shall confirm to IS 2712.2003 and having zinc coating of type heavy as laid down in IS 4826 including binding wire etc fixed to any type of standards posts complete all as specified and as directed.

Supply only 10mm dia round bars, cut to length ,hooking ends as in wooven/ straining bar (stiches through chain link fencing between post) complete all as specified and as directed.

M&L Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and as directed (each line of wire to be measured).

M&L PCC 1:3:6, type C-1(using 20 mm graded stone aggregate) as in precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joint as directed) setting in cement mortar (1:4), in walls including demolition of existing damaged walls complete all as specified and as directed.

M&L Preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L Preparation of new or previously untreated steel surfaces under 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of of red oxide primer complete all as specified and as directed.

Note for item No 13 & 14 :- (a) All synthetic enamel paint, shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

M&L Galvanised steel punched type concertina coil 1050mm dia (dia of coil with unstreched) and streched for a length of 6m per coil while fixing and fixed to angle iron with 3.15mm dia GI wire, including dismanting existing one complete all as specified and as directed by Engineer-in-Charge. Note :- Weight of coil shall not be less than15.2 Kg and shall have129 numbers clip with 50 Turns in each coil.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, cesspits, manholes, pier holes, etc. and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed.

Removal of excavated material to a distance exceeding 1.50 Km and not exceeding 5.00 Km and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Demolition of brick work masonry, built in cement mortar including all quoins, pillars etc., complete all as specified and as directed.

Brickwork with fly ash’ bricks using with modular bricks, straight or curved on plan exc 6m mean radius built in cm 1:4 , complete all as specified and as directed

Description all as per item No 28 here in above but except bricks. Note:Serviceable bricks obtained from Sl item No 27 be reused.

M&L Reinforced precast cement concrete in 1:2:4 type B0 (using12.5mm graded stone aggregate) in Jallies, 45mm thick (measured solid) including all moulding but excluding frame set in CM 1:6 including taking down existing damaged one complete all as specified and as directed. Note: Reinforcement will be measured and paid separately.

M&L Reinforced Cement Concrete 1:2:4, Type B1 (using 20 mm graded granite stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified and directed.

M&L High strength corrosion resistant TMTsteel bar of grade Fe-500 , 6 mm dia to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L High strength corrosion resistant TMTsteel bar of grade Fe-500, 5 mm dia to 10 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips in stirrups , spacers and binders etc complete all as specified and directed.

M&L Rendering 15 mm thick in two layers on brick or concrete surfaces,first coat 10mm thick in cement mortar 1:6 and 2nd coat 5mm thick in cement mortar 1:6 mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete complete all as specified and directed. Note : Water proofing compound shall be measured and paid seperately.

Supply only water proofing compound

M&L applying two coats of cement based paint on newly plastered surfaces of walls including preparation of new surfaces complete all as specified and as directed.

M&L Granite work (of any type) 18 to 20mm thick (table rubbed and polished including round edge) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over and including 15mm thick screed bed in CM 1:4 in repairs complete all as specified and directed by Engineer-in-Charge. Note : (i) Dismantling of stone slab and tiles laid bedded and pointed in any mortar of any discription of thickness in floor (ii) The unit rate is deemed to be included for rounding to edges of stone slabs.

M&L Hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface including removal of existing complete all as specified and directed.

M&L in repairs Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size, polished confirming to IS-15658 of 80mm thickness M-40 grade, laid over and including M sand cushion of 50mm thick and packing the sides with PCC 1:3:6 type C1 (using 20mm graded stone aggregates)complete all as specified and directed. Note : The Unit rate quoted is included for Demolition of paver tiles of any description or thickness in floors,aprons etc laid bedded and pointed in any mortar and removing of debris outside of MD land Note : The manufacturer's test certificate for tiles must be submitted for approval by the concerned authority.

M&L Pre painted Coloured Galvalume roofing system sheet 0.50 mm thick having Zinc aluminum alloy coating AZ150 shall be as per IS:277/ASTM 1379 150 gsm/ sqm double ribbed trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws including dismantling of existing one all complete all as directed.

M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including dimantling of existing one all as directed.

Note for pre-painted coloured Galvalume roofing :-

(i) The manufacturer's test certificate and individual test certificate for the chemical and mechanical properties of sheet must be submitted for approval by the concerned authority prior to installation.

(ii) The contractor shall ensure that no leakages take place from the roof. The roofing shall be Coloured Galvalume roofing system (olive green colour or as approved by GE) with feed material manufactured from 0.50 mm Total coated thickness (TCT), minimum 550 MPa yield strength and shall conform to the physical specifications of IS: 2062 of 2011, coated with hot dip metallic Aluminium / Zinc alloy coating AZ150 as 150 gm/sq.mt total on both sides complete all as specified and as directed.

(iii) The painting shall be coloured baked enamel polyester with silicon coating of film thickness 25 microns nominal on the exposed face/exterior side and on the reverse side ( interior face) shall be white with 15 microns film thickness, over a coat of 5 micron nominal thickness Primer.

(iv) The contractor shall produce purchase vouchers for each lot and independent test for verification of Engineer-in-Charge.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 gradeSt.-240) including dismantling existing one complete all as specified and as directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted , bolted or welded attachment.(Fe 410 -W (Gde- E-250) quality -A complete all as specified and as directed.

S&F in repairs MS flat iron wind ties for roof including securing bolts including all necessary drilling, bolting or riveting, etc. , and similar work conforming to Fe-290 Gde E-165 all as specified and as directed.

Taking down and refixing the same steel gate exc 3.00 but not exc 5.00 sqm in each pane after repair of rusted or damaged portion of the gate including pivot, holdfast, stopper, locking arrangement, pintel etc.. and necessary greasing to shutter, with or including spot welding, running welding all as specified and as directed. Note: New mild steel required for replacing rusted or damaged portion will be measured separately.

M&L Welded steel wire fabric cut to length,bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members not excceding 4Kg/Sqm complete all as specified and directed.

M&L Framed work such as grills, gratings, angles etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of static water tanks and similar work con- forming to Fe.290.Gde-E-165 including dismantling/ taking down existing framed work and applying two coats of synthetic enamel paint including one coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

S&F Mild steel black sheet 0.80mm thick in wall cladding, steel gates and similar works, cut to size, holes punched including round headed screws, clout nails for rebates and fixed to steel framing with plain 40mm lap joints with rebated or weilded seams including bending or turning up mitred angles etc as required complete all as specified and as directed.

M&L Dismantling and re-fixing barbed wire of any description straining and fixing to any type of standrard rails including securing or tying at crossing with and provision of galvanised mild steel wire ,stapple or steel pins complete all as specified and as directed.(Note: Each line of wire to be measured).

M&L in repairs Broken glass coping on top of walls using broken glass pieces fixed in CM (1:3) complete all as specified and as directed. Note : The quoted rates shall be deemed to inclusive of following:- (a) 25mm layer of cement mortar for fixing glass pieces(of bottle or thick glass) broken to approximately 63mm gauge, shall be firmly embedded at the rate of 10 Kg of glass per square metre of rendered surface, jogged edges of the glass being left projecting. (b) Taking down existing glass from coping. (c) Scaffolding for execution of work and protective measures should be taken.

M&L 100 mm thick Plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate ) as in sub base , fillng and mass concrete or as in receiving tiles/ surface channels and drains etc including demolition complete all as specified and directed.

M&L Chequered cement concrete tiles 30cmx30cmx25mm thick machine pressed set jointed and pointed in neat cement slurry as in floors and cut and polished using grey cement and pigments over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) including demolishing the existing tile complete all as specified and directed Note : The manufacturer's test certificate and individual test certificate for tiles must be submitted for approval by the concerned authority prior to installation/fixing.

S&F in repair Anodised aluminium frame powder coated for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

S&F in repair Anodised aluminium door shutters,aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips , rubber neoprene packing, handles 2 Nos in each doors,hinges anodised aluminium snap beading screws etc complete all as specified and as directed.

M&L 9mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination fixed with screws to aluminium frame complete all as specified and as directed.

S&F 4mm thick colour tinted float glass and glazing with oil putty in square exceeding 0.5sqm in each pane complete all as specified and as directed.

S&F Aluminium body door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 kg and fixed including taking down all as specified and as directed.

Supply and fix 150mm long aluminium, anodised, barrel tower bolts of extruded section, in repairs, complete all as specified and directed.

M&L Checking of floor, plinth, plaster etc requiring masonry work and carrying out minor repairs such as edges, patches etc, including petty repairs material like sand, cement & aggregate to make it functional complete all as specified and as directed by Engineer-in-Charge. The rates for plastering / plinth include for: (a) Preparing the surfaces. (b) Thickness of plaster/plinth key in joints, etc. (c) Anises, chamfers of any width, internal rounded angles upto 80mm in width or girth external rounded angles upto 80mm in width or girth. (d) All materials, labour and equipment & supply of integral waterproofing compound, (e) Scoring surface of plastering for key, where the surface is not required to be finished fair. (f) Plastering in patches (in repairs), exc 3 sq.m each patch, for preparing old walls to receive plastering'. Nothing extra shall be admissible for matching with existing work etc. (g) Any individual patch (other than nail hole, plug hole, etc.) are included for provided existing surface finish .

Taking down cement plaster on brick or stone walls, or concrete or ceilings etc, including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises, removal and depositing serviceable materials where directed and leaving the work clear of any plastering and Rendering 15 mm thick in two layers on brick or stone or concrete surfaces,first coat 10mm thick in cement mortar 1:4 and 2nd coat 5mm thick in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed. Note: (a) The unit rate quoted is deemed to include for Removing of accumulated earth of any width and depth upto 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land. (b) Periodicity of cutting of grass shall be before commencement of work and after completion of repairs.

S&F stainless steel letters 12 inches height made out of 1mm thick stainless steel plate, cut folded, welded to required shape including fixing on the granite with bolt nuts/ steel surface etc, including taking down existing one complete all as directed by Engineer - in - Charge

M&L taking down and refixing the steel gate not exc 3.00 sqm in each pane after repair of rusted or damaged portion of the gate including pivot, holdfast, stopper, locking arrangement, pintel etc., and including necessary greasing to shutter, spot/running welding if required all as specified as directed. Note: New mild steel required for replacing, rusted or damaged portion will be measured separately.

Demolition of cement concrete (reinforced) in of any description and in any position and removal of debris out of MD land complete all as specified and directed.

M&L Precast RCC 1:2:4, Type B–1 using 20mm graded stone aggregate as in landings, cover slabs, chullah hoods, Chajjas, water troughs, mangers, Shelves and similar articles with plain faces including formwork, set in cement mortar 1:4 complete all as specified and as directed.

M&L for loose filling with broken bricks of gauge 40 to 80mm in soakage pits, soakage wells complete all as specified and as directed.

Excavating over areas, n exc 1.5 m deep and getting out in any type of soil complete all as specified and as directed.

Excavating over areas, exc 1.5 m but not exc 3 m deep in any type of soil and getting out complete all as specified and as directed.

Excavating over areas, exc 1.5 m but not exc 3 m deep in soft / disintegrated rock and getting out complete all as specified and as directed.

M&L RCC 1:1½:3 Type B-1 using 20mm graded stone agg. as in roof slab complete all as specified and as directed.

M&L form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work: not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

S&F Salt-glazed stoneware drain pipes, 150mm bore, laid in trenches and jointed as specified, complete including demolition of existing pipe any size complete all as specified and as directed.

M&L Plain cement concrete (1:3:6) type C2 (40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of size 150 mm bore of pipe, complete all as specified and as directed.

M&L Providing cement concrete 1:3:6, type C1 (using 20mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and as directed.

Removing debris to out side of MD land to a distance exc 1.5km and not exceeding 5.0 km complete all as directed by Engineer in Charge. Note:-Contractor shall visit the site to ascertain the distance where the materials has to be disposed.

Neptune Engineers and Builders

jk construction

T C KARUNANITHI

A.GOVINDARAJ

KUMAR AGENCIES

kaarthic builders

SARASWATHI CONSTRUCTION

M/s Shana Constructions