Construction of Central Sample Collection Unit, in Basement of OPD Block, AIIMS Patna

Part - (A) Civil Items

EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

"1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size).

REINFORCED CEMENT CONCRETE

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for:

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:4 (1 cement : 4 coarse sand)

WOOD AND P.V.C. WORK

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Approved Make - Godrej

STEEL WORK

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Profile B

Fixing with adjustable lugs with split end tail to each jamb

FLOORING

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

ROOFING

12.54 Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with :

GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler

Single tee with door

75 mm bend

FINISHING

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

15 mm cement plaster on rough side of single or half brick wall of mix:

1:6 (1 cement: 6 coarse sand)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

SANITARY INSTALLATIONS

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.(make- parryware/hindware)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar (make- hindware/perryware)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :

Size 600x450x200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

WATER SUPPLY

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

25 mm dia nominal bore

40 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

25 to 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

40 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :(make- parryware/hindware)

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Cutting holes up to 30x30 cm in walls including making good the same

With common burnt clay F.P.S. (non modular) bricks

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

25 mm nominal bore

40 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length & 15 mm nominal bore

Aluminium Work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed hanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

4mm thick aluminium composite panel material board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.50 mm thickness

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge

Powder coated minimum thickness 50 micron aluminium

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

providing and fixing of PVC flooring of 4.5 mm thick, laid on semi conductive adhesive base and self levelling compound complete in all respect as per specification and as per direction of Engineer-in-charge.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider tings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to ccommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

With stainless steel cover plate minimum 1.25 mm thickness

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used.

300 mm dia piles

Providing and fixing 19mm thick plywood (make - green ply, centuary, national) conforming to IS: 14587:1998 marked,with decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality (make - green lamp, centuary, decor) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately).

19 mm thick

Providing and fixing 19mm thick plywood (make - green ply, centuary, national) conforming to IS: 14587:1998 marked for door pannel and top cover,with decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality (make - green lamp, centuary, decor) in door pannel and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including nickel plated bright finishing ss hinge (make - godrej, o degree) with necessary screw etc. all complete.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete.

Size 40 mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete:

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

Triple strip vertical type

BESCO cubical ZMS black

thickness of Compact laminate - 12mm, Color of HPL boards - single standard Compact Color, size of cubicals - as per drawing (W) &(D) X 2003mm (H), Door size -1750mm (H)x 610mm (W), divider size- 1775mm (H), overall height of cubicals- 2003mm (including bottom gap of 150mm),accessories- standard - merino make aluminium, nylon polyamide 6 accessories), aluminium "U" channel, aluminium "F" channel (only corner Unit),aluminium door stopper channel, aluminium top rail, Nylon coat hook,nylon privacy thumb turn c/w occupancy indicator, nylon door knob, nylon gravity hinges left/right- gravity to close, nylon adjustable foot, rubber door stoper lining, ss screw-304G, & P.v.c wall plugs, note- warapage criteria is 3mm /1000mm for MRS panels as per EN staandard -438.

Part- (B) , Electrical Items

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface I recessed steel conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2X 4 sq. mm + 1 X 4 sq. mm earth wire

2X 6 sq. mm + 1 X 6 sq. mm earth wire

4X 10 sq. mm + 2 X 6 sq. mm earth wire

4X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

3 x 1.5 sq. mm

3x 4 sq. mm

Installation of Exhaust fan in the existing opening , including making good the damage , connection , testing, commissioning etc. as required .

Upto 450 mm sweep

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator

6 Way , Double door

Supplying and fixing following ways surface /recess mounting , vertical type ,415 V TPN MCB distribution board of sheet steel , dust protected , duly powder painted , painted, inclusive of 200 A tinned copper bus bar common neutral link , earth bar , din bar for mounting MCB 's (but without MCB 's and incomer ) as required .

Single Pole 10 Amp.

Single Pole 20 Amp.

Single Pole 32 Amp.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required

8 way (4+24) Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required

Triple pole and neutral (32 Amp.)

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required

Supplying and fixing following size/ modules, Gl box alongwith modular base & cover plate for modular switches in recess etc. as required

3 Module (100mmX75mm)

6 Module (125mmX125mm)

8 Module (200mmX75mm)

Supplying and fixing following modular switch/ socket on the existing modular plate

5/6 A switch

15/16 A switch

10/6 A modular socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

180 mm X 100 mm X 60 mm

200 mm X 125 mm X 60 mm

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17 .5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

Laying and fixing of one number PVC insulated and PVC sheathed I XLPE power cable of 1.1 kV grade of following size on wall surface as required

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed I XLPE aluminium conductor cable of 1.1 kV grade as required.

3.5x120 sq. mm (45 mm)

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing

15 Watt LED Down Light (Round ) syska /crompton

36 Watt Down Light (600 x600 mm)

300 mm 1350 rpm 1 phase EXHAUST FAN (Havells /crompton) turbo force

3.5x120 sq. mm AL Armoured XLPE Cable (Make -Havells /Polycab/Finolex)

25 mm casing caping

Electrical Panel

Incomer 160 Amp. With Ammeter , Volt meter , indicator and copper Bus bar of 200 Amp. outgoing 63 Amp. (2 set),outgoing 40 Amp. (2 set)

Part- ( C ) , Fire Fighting System

100 MM dia butterfly valve with necessary fitting

Dual type pressure gauge complete with pipe stem &Cock

100 mm dia Sprinkler Wet type alarm check valve with trim fitting, ul listed Make HD or Tyco or Eqvalent

4kg ABCpowertypeFireExtinguisher,inhpmildsteel ISI marked fitted with pressure indicating, internal tube, sequence lever type valve full charged with ABC power, pressurized by Nitrogen complete in all respect including wall suspension bracket & conforming to IS 15683.

ISI Marked Portable Fire Extinguisher, CO2 Type capacity 4.5 kg with gun metal cap and Nozzle and complete in all respect including initial filling and wall suspended bracket.

Supplying, Laying, Jointing and testing of following Size Medium grade, MS Pipe , Flange and fitting such as bend, tee, Reducer, Rubber insertion & galavinized Nut & Bolt as per IS; 3589 with up to date amendment I/C fixing the pipe on wall/ Celing with suitable MS strip with /Clamp/ Bracket & painting with 1 coat of anticorrosive paint/Primer & two coat synthetic enamel paint etc. Complete. as required.. pipeshall Have welded connection complete with be velcutby angle grinder and use of three phase rectifier welding set. Rate shall also include cost of hanger & clamp as required & including all civil breakage and making good the same pipe brought to site shall have bevel edge at end shall bevarnish coated externally. C Class, Heavy duty: Pipe Tata, Heavy duty, C. Class

A)150 MM dia Pipe

B) 100 MM dia Pipe

C) 80 MM dia Pipe

D) 65 MM dia Pipe

E) 50 MM dia Pipe

F) 40 MM dia Pipe

G) 25 MM dia Pipe

Providing & Making drainage provision for the raiser with 25 mm dia ball valve completed as required

Providing & Fixing Quartizoid bulb SPRINKLER 68*C Along with necessary attachment

a) Pendant type ( Tyco Make)

b) Upright type ( Tyco Make)

c) Rogger Plate

B) 25/15 mm dia ss flexible hose drop

Fire Alarm system

Supply, Installation, Testing & Commissiong of approved 1 Loop Analog addressable Firealarm system, having the total panel capacity of 156 device. The panel shall be able to give location of all fire & more Fire/ Fault & isolation condition of addressable Unit via the address code. Further, panel must be able to automatically switch off/on respective control module when ever any alarm is triggered. The panel should have inbhult Common alarm, Fault & Monitored sounder ouput. The panel shall have 2”x4- 3/4”. Size VGA Monochrome LCD display. The panel shall have a built in power supply of and battery chargershallbeabletochargethesystembattery..The panel shall have the capacity of connecting additional 15 panel through TCP/IP network or Network terminalusingnetworkcard,withredundancyinthe network. Make ; Honewell Morley, GST & Equivalent

Supply of Intelligent addressable microprocessor based, photoelectric smoke & heat type multicriteria detector with standard base.

Supply of module to monitor Module

Supply of Addressable Control Module for free contact

Supply of Intelligent addressable manual call point to activate manual alarm.

Supply of Addressable Sounder with flasher with Min 82 DB

Supply & laying of 2Cx 1.5mm2 Multistrand FRLS Copper cable in PVC conduit on surface, End termination is required.

Supply of 25 MM pvc pipe with accessories ( Ashirbad)

Emergency/ Exit Light system

Fire Exit Sinage With LED & Battery backup & Charger with Surface Mounted arrangement complete as required, Omni exit/Eton or Equvalent

Supply , Laying & Fixing of 25 Mm PVC Conduit pipe with all accessories Complete as required.

Supply & laying of 2Cx 2.5mm2 FRLS Fire Survival cable for Emergency/Exit Light system complete as required. FRLS

Supply of surface Mounted non maintain Emergency light. Omni/ Exit Eton or Equivalent

Horizontally mounted end suction centrifugal pump, suitable for operation on 415 volts ± 10%, 3 phase, 50 HZ A.C supply, complete with flexible coupling and coupling guard as required. Fire pump having C.I. body, bronze impeller and S.S. Shaft with mechanical seal, capable for delivering 450 LPM of water at total head to ensure a minimum pressure of 3kg/cm2 at the farthest hydrant. Complete with necessary pressure gauge with gun metal shut off cock on delivery side.

Providing & fixing dust and vermin proof cubicle type motor control centre fabricated from 14 SWG MS sheet with powder coated finish and comprising of required incomer, outgoing TPN MCCB, meters & other accessories.

Providing & fixing dust and vermin proof cubicle type motor control centre fabricated from 14 SWG MS sheet with powder coated finish and comprising of required incomer, outgoing TPN MCCB, meters & other accessories.

Providing & fixing cast iron Slim seal dual type non-return valves (PN1.6) complete with matching flanges, rubber insertion, nuts, bolts and washer complete as required.etc. of following sizes.

santosh kumar