Construction of Residential Quarter of S Plus 3 structure at IIM Sambalpur, Odisha.

GENERAL ABSTRACT OF COST

COST AS PER DSR AS PER MARKET

S.NO. DESCRIPTION TOTAL COST (RS.)

2023 (RS.) RATE (RS.)

Digitally signed by JAYA

NBCC (INDIA) LTD

SUB: DETAILED COST ESTIMATE FOR CONSTRUCTION OF RESIDENTIAL QUARTER AT IIM SAMBALPUR

BILL OF QUANTITY (CIVIL ITEMS)

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

1.0 CARRIAGE OF MATERIAL

1.1 By Mechanical Transport including loading,unloading and stacking

1.1.2 Carriage of earth

1.1.4 Carriage of excavated rock

2.6 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over

areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting

out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in

foundation over areas (exceeding 30cm in depth , 1.5 m in width or 10 sqm on plan),

including disposal of excavated earth, for all leads and lifts, disposed earth to be levelled and

neatly dressed.

2.8 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including

dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated

soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.

in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and cum 840.36 840.36 196.00 1,64,710.56

watering, lead up to 50 m and lift upto 1.5 m.

2.25(a) Excavating, supplying, stacking and filling of local earth by mechanical transport upto a lead

of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in cum 278.00 278.00 700.50 1,94,739.00

foundation trenches, plinth, sides of foundation etc. complete for all lift.

2.26 Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or

stacked materials.

2.26.2 Ordinary or hard rock

2.27 Supplying and filling in plinth with sand under floors, including watering, ramming,

consolidating and dressing complete.

2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

2.34.1 Chlorpyriphos/Lindane Emulsifiable concentrate of 20%. Ltr. 73.00 73.00 234.75 17,136.75

2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite

2.35.2.1 Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25

litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/ Lindane

E.C. 20% with 1% concentration

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering - All work up to plinth level

4.1.5 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from natural sources) cum 118.16 118.16 7,294.70 8,61,941.75

4.3 Centering and shuttering including strutting, propping etc. and removal of form for all heights :

4.3.1 Foundations, footings, bases of columns sqm 97.08 97.08 392.15 38,069.92

1 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6

graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm

nominal size, well rammed and consolidated and grouted with fine sand, including necessary

excavation, levelling & dressing & finishing the top smooth.

5.1.2 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15°

landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral

stair cases above plinth level up to floor five level, including the cost of centering, shuttering, cum 35.53 35.53 9,045.75 3,21,395.50

finishing and excluding reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone

aggregate 20 mm nominal size).

5.9 Centering and shuttering including strutting, propping etc. and removal of form for all heights :

5.9.1 Foundations, footings, bases of columns etc. for mass concrete. sqm 302.00 302.00 392.15 1,18,429.30

5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Suspended floors, roofs, landings, balconies and access platform. sqm 2486.00 2486.00 927.25 23,05,143.50

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 2807.00 2807.00 736.40 20,67,074.80

5.9.6 Columns, Pillars, Piers, Abutments, posts and Struts Sqm 2512.00 2512.00 961.30 24,14,785.60

5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 57.06 57.06 764.95 43,648.05

5.9.16 Edges of slabs and breaks in floors and walls. 0.00 0.00

5.9.19 Weather shade, chajjas, corbels etc. including edges. sqm 120.00 120.00 951.10 1,14,132.00

5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position

and binding all complete upto plinth level

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 32652.156 32652.16 107.85 35,21,535.46

5.22 A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500 D or more. kg 107241.80 107241.80 107.85 1,15,66,028.13

5.33 Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to

5.33.1 All works upto plinth level

5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 204.00 204.00 9,504.75 19,38,969.00

5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 91.52 91.52 9,655.70 8,83,689.66

5.33.2 All works above plinth level upto floor V level

5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 588.42 588.42 9,860.40 58,02,056.57

5.33.2.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 244.00 244.00 10,011.35 24,42,769.40

5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

5.35 Add for using extra cement in the items of design mix over and above the specified cement

content therein. quintal 237.73 237.73 733.50 1,74,374.96

6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundation and plinth in:

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 27.20 27.20 7,132.25 1,93,997.20

6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of

half brick masonry.

6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : Mtr 244.00 244.00 59.45 14,505.80

6.34.1 Brick work with non modular fly ash bricks conforming to IS:12894,

class designation 10 average compressive strength in super structure cum 550.52 550.52 8,962.35 49,33,952.92

above plinth level up to floor V level in : Cement mortar 1:4 (1 cement : 4 Coarse sand)

2 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of

required size, approved shade, colour and texture laid over 20 mm thick base cement mortar

1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give

high gloss finish etc. complete at all levels.

8.2.2 Granite stone slab of colour black, Cherry/Ruby red

8.3 Providing edge moulding to 18 mm thick marble stone counters, Vanities

etc., including machine polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-Charge.

8.4 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and

drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. Mtr 144.60 144.60 568.55 82,212.33

8.5 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen

platform, vanity counter and similar location in marble/ Granite/ stone work, including

necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc.

26.86 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid

door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer

of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/

rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)

fabricated with miter joints after applying PVC solvent cement and screwed with full body

threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw

withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58

N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A

category with property of being termite/borer proof, water/moisture proof and fire retardant

and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length

complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners

shall be paid for separately).

9.12 Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm

thick in doors, windows and clerestory window shutters. (Area of opening for glass panes sqm 30.24 30.24 176.40 5,334.34

excluding portion inside rebate shall be measured).

26.88 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid

decorative type flush door shutter of required size comprising of virgin polymer of K value 58-

60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat

husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having

minimumdensity of 650 kg/cum and screw withdrawal strength of 1800

N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity

850 N/mm2 and resistance to spreadof flame of Class A category with property of being

termite/borer proof, water/moisture proof and fire retardant. WPC to

be laminated with PVC foil of minimum 14 microns thick ofapproved design pasted with hot

melt adhesive on both facesof shutter and fixing with stainless steel butt hinges of

requiredsize with necessary full body threaded star headed counter sunk S.S screws, all as

per direction of Engineer-In- Charge.

(Note: stainless steel butt hinges and necessary S.S screws

shall be paid separately)

26.88.1 30 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

26.82.2 35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of door shutter to be measured). sqm 235.62 235.62 462.35 108938.91

9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). sqm 315.62 315.62 106.70 33,676.65

3 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm

1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

9.74 Providing and fixing bright finished brass tower bolts (barrel type) with

necessary screws etc. complete :

9.74 Providing and fixing bright finished brass tower bolts (barrel type) with

necessary screws etc. complete :

9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary

screws, etc. complete.

9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door

closer (having brand logo with ISI, IS: 3564, embossed on the body, door weight upto 36 Kg.

to 80 Kg. and door width from 701 mm to 1000 mm), with double speed adjustment with Each 24.00 24.00 983.15 23,595.60

necessary accessories and screws etc. complete.

9.88 Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a

pair of lever handles of approved quality with necessary screws etc. complete. Each 147.00 147.00 998.35 1,46,757.45

9.89 Providing and fixing chromium plated brass night latch of approved quality including necessary

screws etc. complete. Each 147.00 147.00 952.80 1,40,061.60

9.92 Providing and fixing chromium plated brass handles with necessary screws etc. complete:

9.127 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss /

matt / suede finish with high density protective surface layer and reverse side of adhesive

bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved

9.147A Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead

free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded

profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10

mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design

duly reinforced with galvanized mild steel section

made of required shape & size as per CPWD Specification, uPVC extruded glazing beads,

interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM

gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head,

comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS

1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc.

Profile of frame, sash & mullion (if required) shall be mitred cut and fusion

welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing

hardware and drainage of water etc. After fixing frame the gap between frame and adjacent

finished wall shall be filled with weather proof silicon

sealant over backer rod of approved size and quality, all complete as per approved drawing

conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel

reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-

in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with /

without high performance coatings as per design requirements and conforming to IS: 3548 &

IS: 16231 shall be paid separately.Note:- Structural design proof checked from a Government

Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed >

45 m/sec as per IS 875 — Part 3

(ii) Sites with structure height more than 20m for all wind speeds

9.147.A4 Three track three panels sliding window with two glazed & one wire mesh panels with

Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.

9.147.A4.1 Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen

sash (25 mm & above) x (50 mm & above) with zinc alloy (Zamak) powder coated touch locks sqm 522.54 522.54 10,993.55 57,44,569.62

with hook. (Height upto 1.2 metre).

4 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

9.149 Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC

casement window with necessary screws etc. complete. each 60.00 60.00 231.05 13,863.00

9.153 Providing and fixing steel (white power coated) crescent lock for uPVC

sliding window/ door with necessary screws etc. complete. each 300.00 300.00 198.30 59,490.00

STEEL WORK 0.00 0.00

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,

including cutting, hoisting, fixing in position and applying a priming coat of approved steel Kg. 7525.80 7525.80 133.70 10,06,199.46

primer all complete:

10.27 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10

mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head,

comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame ,

concrete/ masonry, etc. as per direction of Engineer-in-charge.

10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels,

plates etc., including welding, grinding, buffing, polishing and making curvature (wherever

required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing

the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts

etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement

as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel

members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

10.29 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat

15x3 mm and nuts & bolts complete.

10.29.2 Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness

with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns

epoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should

have protective guard film of 25 micronsminimum to avoid scratches during transportation and

should besupplied in single length upto 12 metre or as desired by Engineer in-charge. The sqm 374.00 374.00 738.65 2,76,255.10

sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM

seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost

ofpurlins, rafters and trusses and including cutting to size and shape

wherever required.

FLOORING 0.00 0.00

8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved make, in all colours, shades except burgundy,

bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed

with pigment of matching shade complete.

11.39 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more

(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of

approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement

mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/ sqm

including grouting the joints with white cement and matching pigments etc., complete.

11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar

1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting

the joints with white cement and matching pigments etc. The tiles must be cut with the zero 0.00 0.00

chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge,

clips of required thickness, leveling system and rubber mallet for placing the tiles gently and

11.41A.1 Double charge vitrified tile polished finish of size 0.00 0.00

5 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

11.46 Providing and laying Vitrified tiles in different sizes (thickness to be specified by

manufacturer), with water absorption less than 0.08 % and conforming to |.S. 15622, of

approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of

cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm

including grouting the joint with white cement & matching pigments etc.

11.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear

as well as curvilinear portions of the building all complete as per the architectural drawings

with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement

: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry 0.00 0.00

admixed with pigment of matching shade including rubbing , curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

11.56.1 Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent Sqm 212.50 212.50 4,481.30 9,52,276.25

ROOFING 0.00 0.00

12.21 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone

aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3

fine sand) as per standard design : In 75x75mm deep chase

12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet

1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) each 13.00 13.00 298.25 3,877.25

and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

12.52.3 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of

Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated

with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized

polyester on the back side with all edges sealed with the face side PVC film which goes Sqm 283.00 283.00 2,215.15 6,26,887.45

around and wraps the edges and is bonded to the edges and the back side metalized

polyester film so as to make the tile a completely sealed unit.

FINISHING: 0.00 0.00

13.1 12 mm cement plaster of mix :

13.12 18 mm cement plaster in two coats under layer 12 mm thick cement plaster

1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement

plaster 1:6 (1 cement : 6 fine sand).

Neat cement punning

13.21 Extra for providing and mixing water proofing material in cement per bag of

plaster work in proportion recommended by the manufacturers.

13.22 Extra for plastering exterior walls of height more than 10 m from ground level for every

additional height of 3 m or part thereof.

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved

brand and manufacturer, over the plastered wall surface to prepare the surface even and sqm 4618.00 4618.00 156.05 7,20,638.90

smooth complete.

13.83 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to achieve even shade and colour.

6 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

16.91 Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot

path, park & lawns driveway or light & traffic parking etc. of required strength, thickness &

size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern

over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of

inter locking paver blocks into the sand bedding layer through vibratory compaction by using 0.00 0.00

plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and

pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications

& direction of Engineerin- Charge

16.91.1 60mm thick Cement concrete paver block of M-35 grade with approved colour, design &

16.78 Construction of granular sub-base by providing close graded Material conforming to

specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers

to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor

grader on prepared surface and compacting with vibratory power roller to achieve the desired

density, complete as per specifications and directions of Engineer-in-Charge.

16.78.1 With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

16.10 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity

after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating

with road roller including making good the undulations etc. and re-rolling the sub grade and

disposal of surplus earthwith lead upto 50 metres.

16.80 Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse

and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm,

aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per

specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to

be determined during trial length construction, concrete strength not to be less than 10 Mpa at cum 59.40 59.40 4,148.65 2,46,429.81

7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a

mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc.

complete as per direction of Engineer_x0002_in- charge.

16.75 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching

plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum

dewatering process and finally finished by floating, brooming with wire brush etc. complete as

per specifications and directions of Engineer-incharge. cum 59.40 59.40 9,823.80 5,83,533.72

(The panel shuttering work shall be paid for separately).

(Note:- Cement content considered in this item is @ 330 kg/cum.

Excess/less cement used as per design mix is payable/ recoverable separately).

16.46.1 Providing and filling in position rubberized bitumen hot sealing compound for sealing of Per cm

expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Width per

Using grade 'A' sealing compound conforming to IS: 1834 cm width 786.00 786.00 8.65 6,798.90

16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement

concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1

cement: 3 coarsesand), including making joints with or without grooves (thickness of joints

except at sharp curve shall not to more than 5mm), including making drainage opening

wherever required complete etc. as per direction of Engineer-in-charge (length of finished

kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved

by Engineer-in-charge).

ALUMINIUM WORK:

7 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

25.3 Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-

sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as

required and specified,comprising of an outer heat strengthened float glass 6mm thick, of

approved colour and shade with reflective soft coating on surface # 2 of approved colour and

shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide,

dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all sqm 189.02 189.02 3,718.70 7,02,908.67

complete for the required performances, as per the Architectural drawings, as per the

approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs

shall be assembled in the factory/ workshop of the glass processor.

21.8 Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing

weather silicon sealant over backer rod of approved quality as per architectural drawings and

direction of Engineer-in-charge complete.

21.8.1 Upto 5 mm depth and 5 mm width metre 923.20 923.20 96.75 89,319.60

21.15 Providing and fixing aluminium casement windows fastener of required length for aluminium

windows with necessary screws etc. complete.

21.15.1 Anodized (AC 15) aluminium each 176.00 176.00 89.40 15,734.40

WATER PROOFING:

22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed

portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS 2645 in recommended proportions including rounding off junction of vertical

and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water

proofing compound in recommended proportion including rounding off junction of vertical and

horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be

100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

22.14.1 Grading roof for water proofing treatment, cement concrete 1:2:4 with 20mm nominal size cum 71.10 71.10 8,042.30 5,71,807.53

Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three

layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l

Type ll), having one side decorative lamination and other side balancing lamination, including

IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright

finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge

Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with

one side decorative lamination other side balancing lamination Grade-I (exterior grade) in

shelves with screws and fittings wherever required, edges to be sealed with PVC edge

bending tape 2.00 mm thick of approved brand (fittings to be paid separately).

Pre-laminated with decorative lamination one side and other side balancing lamination exterior

Grade - I MDF Board 18 mm thick confirming to IS:14587

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe

shutters, including fixing with necessary screws etc. complete.

9.114.1 Double strip (horizontal type) Each 48.00 48.00 39.70 1,905.60

TOTAL OF SCHEDULE ITEM 7,13,77,049.49

NON-SCHEDULE ITEM

8 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

MR-3 Providing and applying surface Stone textured finish with 100% natural granite & ceramic

protection coating of approved shade or approved equivalent make) comprising of water-

borne, penetrating, water repellent EM- primer & super durable water based acrylic silicon

resin clear and super durable dirt and dust resistant protection coat of FSI Clear coat, which

shall be highly water repellant, Anti-algae & anti-fungal in nature to external wall surfaces. The

coating shall also cover hairline cracks with application method which includes one coat of El

primer, one coat of Stoney, all in approved colour and texture. It shall also include preparation sqm 1513.60 1513.60 2,762.31 41,81,032.42

of surface, appropriate primer coat etc. applied as per manufacturer's & project consultant

instructions. Scaffolding and staging shall be allowed as required. The finish shall be in

natural colour/ non pigmented, water repellant, resistant to ultra violet, alkali and condensate

formation . All hairline cracks/ crazing shall be covered & shall ensure good breathability for

the substrate. Finished work would be to the satisfaction of the Engineer in charge.

MR-4 Providng and fixing powder coated/Anodized finish aluminium louvers made up of aluminium

alloy 6063-T5/ T6 at the external and internal service shafts with frame and other necessary

accessary fittings, fixtures as per the approved design and drawing etc. The minium blade sqm 378.40 378.40 5,652.00 21,38,716.80

thickness shall be of 1.2 mm. aluminium section shall be as per the site requirement, shaft

MR-5 Providing and fixing of clay tiles of size-225+-5x70+-5 mm on the plastered surface using tile

adhesive and filling the gap with mortar at all heights and making any pattern as per 3D sqm 1135.20 1135.20 3,966.00 45,02,203.20

design or approval from the client.

MR-6 Modular Kitchen

1 Base Cabinet -:

Providing and Fixing the Factory made modular kitchen having Single bowl sink with drain

board and cooking platform of 18 mm thick granite with double molding at facia of approved

shade with back panel of 6mm thick BWP Ply including both side balancing fabric finish

laminate and Internal Cabinet i.e Non Visible Sides.

Top, Bottom and Shelfs are of 18mm thick BWP Ply Including Both side balancing fabric

finish laminate. Front Shutters and Visible Side Should be of 18mm thick BWP Ply including

front side 1mm thick Decorative Matt/High Gloss Finish Laminate of approved make and Back

Side Balancing Fabric Finish Laminate.

Cabinet To be made in minifix with all fixtures as per requirement.

All Edges of Internal Cabinet and Shutters shall be finished with PVC Edge Banding Tape of

required size with the hot melt adhesive by throughfeet machine.

2 Fitting & Fixtures -:

1. Cabinet Hinges Slip On Soft Close Hinge Full Overlay/Half overlay as per requirement of 2

Hole with a opening angle shutter.

2. Gola J/C Profile on under counter cabinet shutters shall be provided of approved colour and

3. Pvc Cutlery fixed as per Size Requirement.

4. Innotech Drawers/ Slim Ergo Drawer System, Grain Trolly etc. 4''/8'' as per the requirement

having anthracite colour. Every slim ergo system shall be of weight capacity 30 kg.

5. Glass Tray, Plate Tray of approved quality and of size as per requirement at site 6. Shutter

Dustbin of 14L Black and silver finish of Approved Quality and brand. Job 12.00 12.00 31,673.00 3,80,076.00

7. PVC Legs and Skirting of 100mm Height to be provided below the counter of kitchen

cabinets with desired finish.

8. shall be used wherever required as per drawings.

9. GTPT of SS 304 grade Shall be provided as per drawings.

10. Bottle Organiser shall be provided.

11. 4 Burner Built in Toughened/Tempered Glass Hob with auto electric ignition technology

shall be provided as per drawing .

12. Heavy Duty Soft Close Drawer Channels with carrying capacity of min 30 Kg

9 Digitally signed by JAYA

DSR 2023 DESCRIPTION Unit Qty-Block (A) Qty Rounded Rate DSR Amount

3 Overhead Cabinet -:

The overhead factory made counter of kitchen shall be made in 18mm thick BWP Ply

including both side balancing fabric finish laminate and Internal Cabinet i.e Non Visible Sides,

Top, Bottom and Shelfs are of 18mm thick BWP Ply Including Both side balancing fabric finish

laminate. Front Shutters and Visible Side Should be of 18mm thick BWP Plyincluding front

side 1mm Thk Decorative Matt/High Gloss Finish Laminate of Approved Make and Back Side

Balancing Fabric Finish Laminate. Cabinet To be made in minifix with all fixtures as per

requirement using 2 head Multi boaring machine. Job 12.00 12.00 80,373.00 9,64,476.00

All Edges of Internal Cabinet and Shutters shall be finished with PVC Edge Banding Tape of

required size with the hot melt adhesive by throughfeet machine.

1. The partitions shall be provided in each cabinet for storage purpose as per the drawings.

2. The Aluminum handle profile 50mm shall be provided for all the glass shutters to give a

3. The Chimney having Airflow Capacity of 1200 CMPH or above with features like mood

light, auto clean mode, touch and gestures control.

MR-7 Prepartion of all detail architetural drawings, MEP drawings, structural drawings based on

concept drawing provided and its vetting from NIT/IIT or Govt. engineering college/Univerisity

(a) Preparation of all Architetural GFC drawings and its approval from EIC/Client. Job 1.00 1.00 3,10,000.00 3,10,000.00

(b) Preparation of all services/MEP GFC drawings and its approval from the EIC/Client Job 1.00 1.00 3,10,000.00 3,10,000.00

(c) Preparation of all structural drawings and its vetting from NIT/IIT or Govt. engineering

college/Univerisity.

(d) Preparation of external drawings including services, roads other than buildings.

TOTAL OF NON-SCHEDULE ITEM 1,40,50,656.42

10 Digitally signed by JAYA

DSR - DESCRIPTION OF ITEM DSR-2023 AMOUNT

2023 /NS RATE (RS.) (RS.)

ITEM No. SANITARY FIXTURE

17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole

basin mixer of approved quality and make, including painting of fittings and

brackets, cutting and making good the walls wherever required:

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single

hole basin mixer

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983

with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and

brackets, cutting and making good the walls wherever required :

17.10.1 Kitchen sink with drain board

17.22A Providing and fixing CP Brass 32mm size Bottle Trap of

approved quality & make and as per the direction of Engineerin- Each 72 1034.80 74505.60

17.22 B Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make

as approved by Engineer in charge.

a) 15 mm nominal dia Each 48 6940.75 333156.00

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior

glass (of approved quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass screws and washers

17.34 Providing and fixing toilet paper holder :

18.21 Providing and fixing uplasticised PVC connection pipe with brass

18.21.1 30cm length

18.21.1.1 15mm nominal bore Each 96 85.00 8160.00

18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet

18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931

18.49.1 15mm nominal bore Each 48 506.80 24326.40

18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of

approved quality conforming to IS:8931

18.53.1 15mm nominal bore Each 96 574.30 55132.80

18.53A Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of

approved make and quality as per direction of Engineer-in-charge. Each 192 74.80 14361.60

SUB TOTAL( SANITARY FIXTURE) 1005169.20

NS-1 Providing and fixing Wall Hung water closet with Half frame & Consealed

flushing cistren ,flush plate, along with all accessories , complete in all respect as Each 48 23420.21 1124170.01

per the direction of Engineer-in-Charge.

NS-2 Providing and fixing C.P. brass 2 Way bib cock with Health Faucet ABS with Rubbit

Cleaning System 1.25 m Long SS Flexible Tube & ABS Wall Hook as per direction Each 48 3452.35 165712.58

of Engineer-in-charge.-

NS-3 Providing and fixing single lever sink mixer (wall mounted) complete in all respect

NS-4 Providing and fixing waste coupling 32 mm dia SS complete in all respect Each 48 363.90 17467.00

NS-5 Providing and fixing soap tumbler holder (Brass) complete in all respect Each 48 867.75 41652.08

NS-6 Providing and fixing ss towel rod complete in all respect Each 48 1026.37 49265.90

NS-7 Providing and fixing Stainless steel grating with frame for floor traps or drains of

required pattern complete in all respect Each 60 1089.27 65356.45

NS-8 Providing and fixing Flash touch-free infrared hand dryer complete in all respect

NS-9 Providing & Fixing of Grab bar size U-type 600X600 mm pipe O.D 32 mm ,

thiickness 2 mm of non slipping grip as per standard specification of use in

disabled toilet complete with brackets suitable for wall installation as per Each 12 16030.83 192369.91

approved sample complete in all respect.

NS-10 Providing & Fixing of Grab bar straight CP brass size 300 mm pipe O.D 32 mm ,

thiickness 2 mm of non slipping grip as per standard specification of use in

disabled toilet complete with brackets suitable for wall installation as per Each 12 1736.67 20840.07

approved sample complete in all respect.

NS-11 Providing & Fixing of Grab bar straight CP brass size 600 mm pipe O.D 32 mm ,

thiickness 2 mm of non slipping grip as per standard specification of use in

disabled toilet complete with brackets suitable for wall installation as per Each 12 2980.09 35761.07

approved sample complete in all respect.

SUB TOTAL( NS-SANITARY FIXTURE) 2284714.04

SOIL ,WASTE & VENT PIPES AND FITTINGS

17.35 Providing and fixing soil, waste and vent pipes :

17.35.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside

17.35.2.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside

17.37 Providing and fixing M.S. holder-bat clamps of approved design to

Sand Cast iron/cast iron (spun) pipe embedded in and including

cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size),

including cost of cutting holes and making good the walls etc. :

17.38 Providing and fixing bend of required degree with access door, insertion rubber

washer 3 mm thick, bolts and nuts complete.

17.38.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per

17.38.2.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per

17.39 Providing and fixing plain bend of required degree

17.39.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside

17.39.2.3 Hubless centrifugally cast (spun) iron pipe epoxy coated inside & outside Each 8 252.50 2020.00

17.43 Providing and fixing single equal plain junction of required degree with access

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

17.43.1.2 Sand cast iron S&S as per IS - 3989 Each 16 925.70 14811.20

17.44 Providing and fixing single equal plain junction of required degree :

17.44.1.3 Hubless centrifugally cast (spun) iron epoxy

coated inside & outside as per IS:159 Each 16 581.45 9303.20

17.56 Providing and fixing terminal guard :

17.56.1.3 Hubless centrifugally cast (spun) iron epoxy

coated inside & outside as per IS:15905 Each 32 427.80 13689.60

17.56.2.2 Sand Cast iron S&S as per IS-3989 Each 11 404.75 4452.25

17.57A Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe

17.57A.1 100 mm dia

17.57A.1. SS 304 grade coupling with EPDM rubber gasket Each 96 432.05 41476.80

17.57A.2 75mm dia

17.57A.2. SS 304 grade coupling with EPDM rubber gasket

17.59 Providing and fixing M.S. stays and clamps for sand cast iron/

centrifugally cast (spun) iron pipes of diameter :

17.60 Providing and fixing trap of self cleansing design with screwed down or hinged

grating with or without vent arm complete, including cost of cutting and making

good the walls and floors :

17.60.1 a) 100 mm inlet and 100 mm outlet

17.60.1.3 Hubless centrifugally cast (spun) iron epoxy

coated inside & outside as per IS:15905

17.60.2 b) 100 mm inlet and 75 mm outlet

17.60.2.3 Hubless centrifugally cast (spun) iron epoxy coated

inside & outside as per IS:15905 Each 1 591.40 591.40

17.61 Cutting chases in brick masonry walls for following diameter sand cast iron/

centrifugally cast (spun) iron pipes and making good the same with cement

concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm

nominal size), including necessary plaster and pointing in cement mortar 1:4 (1

cement : 4 coarse sand) :

SUB TOTAL( SOIL, WASTE & VENT PIPES) 945488.08

NS-12 Providing and fixing Clean out plug with clamp complete in all respect Each 16 814.75 13036.06

NS-13 Providing and fixing uPVC SCH-80 pipe for waste wash basin to loor trap with

fittings complete in all respect

NS-14 Providing and fixing 100 x 75 x50 mm multy inlet (smart) floor trap hubless

including cost of cutting and making good the walls and floors :

NS-15 Providing and fixing Multy Inlet (100x50) hubless Pipe including cost of cutting

and making good the walls and floors :

SUB TOTAL NON SCHEDULED ( SOIL, WASTE & VENT PIPES) 76910.52

18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00

m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete

as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20 mm nominal outer dia Pipes Mtr 12 335.00 4020.00

18.7.3 25 mm nominal outer dia Pipes Mtr 66 401.55 26502.30

18.7.4 32 mm nominal outer dia Pipes Mtr 85 518.75 44093.75

18.7.5 40 mm nominal outer dia Pipes Mtr 52 702.95 36553.40

18.7.6 50 mm nominal outer dia Pipes Mtr 22 934.15 20551.30

NS-16 Providing and fixing CPVC SCH-80 pipe (3/5 mtr) 65 mm nominal outer dia Pipes

18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clampsat 1.00 m

spacing. This includes jointing of pipes & fittings with onestep CPVC solvent

cement and the cost of cutting chases and making good the same including

testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

18.8.1 15 mm nominal outer dia Pipes Mtr 131 497.80 65211.80

18.8.2 20 mm nominal outer dia Pipes Mtr 98 537.60 52684.80

18.8.3 25 mm nominal outer dia Pipes Mtr 58 627.25 36380.50

18.8.4 32 mm nominal outer dia Pipes Mtr 32 739.30 23657.60

18.10 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting

and making good the walls etc.

Internal work-Exposed on wall

18.10.4 32 mm dia nominal bore Mtr 15 667.00 10005.00

18.10.5 40 mm dia nominal bore Mtr 15 811.90 12178.50

18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and

18.12.4 32 mm dia nominal bore Mtr 118 540.30 63755.40

18.12.5 40 mm dia nominal bore Mtr 110 617.05 67875.50

18.12.6 50 mm dia nominal bore Mtr 20 762.15 15243.00

18.13 Making connection of G.I. distribution branch with G.I. main of following sizes by

providing and fixing tee, including cutting and threading the pipe etc. complete :

18.13.1 25 to 40 mm nominal bore Each 2 911.90 1823.80

18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved

quality (screwed end) :

18.17.1 25mm nominal bore Each 7 622.40 4356.80

18.17.1 A 20 mm nominal bore Each 1 539.95 539.95

18.17.2 32mm nominal bore Each 10 689.60 6896.00

18.17.3 40mm nominal bore Each 4 826.10 3304.40

18.17.4 50mm nominal bore Each 2 1026.65 2053.30

18.17.5 65 mm nominal bore Each 1 1742.15 1742.15

18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure,

with plastic floats complete :

18.18.2 20 mm nominal bore Each 2 462.50 925.00

18.19 Providing and fixing gun metal non- return valve of approved quality

(screwed end) :

18.19.3 40 mm nominal bore

18.19.3.1 Horizontal Each 1 952.60 952.60

18.19.4 50 mm nominal bore

18.19.5 65 mm nominal bore

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage

tank, IS : 12701 marked, with cover and suitable locking arrangement and making

necessary holes for inlet, outlet and overflow pipes but without fittings and the

base support for tank

SUB TOTAL( WATER SUPPLY) 686421.43

NON SCHEDULED ( WATER SUPPLY )

NS-20 Self-priming close-coupled centrifugal pumps with built-in ejector system,

coupled with a Asynchronous, squirrel cage rotor, IE2 efficiency class ,

enclosed construction in aluminum casing, external ventilation, Protection:

IP55. / 415 or 230 V / 50 Hz, Class 155 (F) insulation. Performances

according to EN 60034-1. ,Maximum ambient temperature: 40°C. , (-

Single-phase version: 220-240 V 50 Hz, 2 poles with built-in automatic set 2 37581.42 75162.84

reset overload protection. Three-phase version: 220-240/380-415 V 50 Hz),

with SS body , SS 304 impeller & with fill & drain plug , with mechnical seal

complying to Mechanical seal with mounting dimensions according to

SUB TOTAL NON SCHEDULED ( WATER SUPPLY) 75162.84

RAIN WATER PIPING

12.44 Providing and fixing to the inlet mouth of rain water pipe cast iron

grating 15 cm diameter and weighing not less than 440 grams. Each 12 54.70 656.40

12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS

: 5382, leaving 10 mm gap for thermal Expansion,(i) Single socketed pipes.

12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories

for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,

including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for

thermal expansion.

12.42.1 Coupler

12.42.2 Single push fit Coupler

12.42.3 Single tee with door

12.42.6 Shoe (Plain)

12.43 Providing and fixing unplastisized PVC pipe clip approved design to unplastisized

PVC rain water pipes by meanes of 50x50x50 mm hard wood plugs,screwed with

M.S screws of required length,including cutting brick and fixing in cement morter

1:4(1 cement:4 coarse sand) and making good the wall etc complete.

SUB TOTAL( RAIN WATER PIPING) 68375.60

SEWERAGE & DRAINAGE

19.1 Providing,laying and jointing glazed stoneware pipes class SP-1 with stiff mixture

of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including

testing of joints etc. complete :

19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse

sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes

including bed concrete as per standard design :

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10

graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes

including bed concrete as per standard design :

19.3.2 150 mm diameter S.W. pipe Mtr 280 743.10 208068.00

19.3.3 200 mm diameter S.W. pipe Mtr 244 873.50 213134.00

19.4 Providing and fixing square-mouth S.W. gully trap class SP-1

complete with C.I. grating brick masonry chamber with water tight

C.I. cover with frame of 300 x300 mm size (inside) the weight of

cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per

standard design:

19.4.1 100x100mm size 'P' type

19.4.1.1 With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C.pipes with collars

jointed with stiff mixture of cement mortar in theproportion of 1:2 (1 cement : 2

fine sand) including testing of joints etc. complete :

19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1

cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),

foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone

aggregate 40 mm nominal size), inside plastering 12 mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement

and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) finished with a floating coat of neat

cement complete as per standard design :

19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. coverwith frame (light duty)

455x610 mm internal dimensions,total weight of cover and frame to be not less

than 38 kg(weight of cover 23 kg and weight of frame 15 kg) :

19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 10 12770.55 127705.50

19.8 Extra for depth for manholes :

19.8.1 Size 90x80 cm

19.8.1.1 With common burnt clay F .P .S. (non modular) Mtr 1 8825.40 8825.40

19.9 Constructing brick masonry circular type manhole 0.91 m internaldia at bottom

and 0.56m dia at top in cement mortar 1:4 (1 cement: 4 coarse sand), inside

cement plaster 12 mm thick with cementmortar 1:3 (1 cement : 3 coarse sand)

finished with a floating coatof neat cement, foundation concrete 1:3:6 mix (1

cement : 3 coarsesand : 6 graded stone aggregate 40 mm nominal size), and

makingnecessary channel in cement concrete 1:2:4 (1 cement : 2 coarsesand : 4

graded stone aggregate 20 mm nominal size) finishedwith a floating coat of neat

cement, all complete as per standard

19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation)

560 mm internal diameter conforming to I.S. 12592, total weight of cover and

frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering,

shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at

the external surface shall be paid for separately) :

19.9.1.1 With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

19.16 Providing orange colour safety foot rest of minimum 6 mm thickplastic

encapsulated as per IS : 10910, on 12 mm dia steel barconforming to IS: 1786,

having minimum cross section as 23 mmx25mm and over all minimum length 263

mm and width as 165 mm withminimum 112 mm space between protruded legs

having 2 mm treadon top surface by ribbing or chequering besides necessary

andadequate anchoring projections on tail length on 138 mm as perstandard Each 58 553.70 32114.60

drawing and suitable to with stand the bend test and chemical resistance test as

per specifications and having manufacture's permanent identification mark to be

visible even after fixing, including fixing in manholes with 30x20x15 cm cement

concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm

nominal size) complete as per design.

19.21 Making connection of drain or sewer line with existing manhole

including breaking into and making good the walls, floors with cementconcrete

1:2:4 mix (1 cement : 2 coarse sand : 4 graded stoneaggregate 20 mm nominal

size) cement plastered on both sideswith cement mortar 1:3 (1 cement : 3 coarse

sand), finished with afloating coat of neat cement and making necessary channels

forthe drain etc. complete :

19.21.1 For pipes 100 to 250 mm diameter Each 1 810.45 810.45

Providing sand cast iron drop connection externally for 60 cm drop

from branch sewer line to main sewer manhole including inspectionand cleaning

eye with chain and lid, sand cast iron drop pipe andbend encased all-round with

cement concrete 1:5:10 (1 cement :5 fine sand : 10 graded stone aggregate 40

mm nominal size) withall centering and shuttering required, cutting holes in walls

19.22 andmaking good with brick work in cement mortar 1:4 (1 cement : 4coarse sand)

plastered with cement mortar 1:3 (1 cement : 3coarse sand) on inside of the

manhole wall, lead caulked jointsbetween sand cast iron pipes and fittings, stiff

cement mortar 1:1(1 cement : 1 fine sand) joints between sand cast iron tee

andS.W. pipe, making required channels complete as per standarddesign and

specifications :

19.22.2 150 mm dia sand cast iron drop connection

19.27 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in

cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast

R.C.C. horizontal grating with frame complete as per standard design :

19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

SUB TOTAL( SEWERAGE & DRAINAGE) 1477890.45

2.6 Earth work in excavation by mechanical means (Hydraulic excavator)/manual

means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on

plan) including getting out and disposal of excavated earth lead upto 50 m and lift

upto 1.5 m, as directed by Engineer-in-charge.

2.6.1 All kind of soil Cum 51 177.50 9059.32

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding 20cm in depth, consolidating each Cum 28 196.00 5393.76

deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m

2.10 Excavating trenches of required width for pipes, cables, etc includingexcavation

for sockets, and dressing of sides, ramming of bottoms,depth upto 1.5 m,

including getting out the excavated soil, and thenreturning the soil as required, in

layers not exceeding 20 cm in depth,including consolidating each deposited layer

by ramming, watering,etc. and disposing of surplus excavated soil as directed,

within a leadof 50 m :

2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm dia Mtr 456 352.15 160580.40

SUB TOTAL( EARTH WORK)

Sl. No. Descriptions Unit Qty Rate (Incl. 18% GST) Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper

conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable

GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface /

34 1.11 recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 Point 14 ₹ 1,803.00 ₹ 25,242.00

sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/

35 1.12 recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable Meter 400 ₹ 373.00 ₹ 1,49,200.00

for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/

36 1.13 recessed medium class PVC conduit along with 2 Nos. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable Meter 100 ₹ 587.00 ₹ 58,700.00

for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper

conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned

copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but

59 1.24 excluding modular plate etc. as required. ₹ -

65 1.24.6 Telephone socket outlet Each 48 ₹ 168.00 ₹ 8,064.00

66 1.24.7 TV antenna socket outlet Each 48 ₹ 168.00 ₹ 8,064.00

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

Digitally signed by JAYA

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess

etc. as required.

77 1.28 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. ₹ -

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing

and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing

and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as

89 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. Each 14 ₹ 112.00 ₹ 1,568.00

Installation, Testing and Commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with

1.5 sq. mm FRLS/HFFR PVC insulated, copper conductor, single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch

etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing

the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,

99 2.3 complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including ₹ -

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet

steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din

bar for mounting MCBs (but without MCBs and incomer ) as required .(Note : Vertical type MCB TPDB is normally used

where 3 phase outlets are required.)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of

112 2.10 following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. ₹ -

114 2.10.2 Single pole and neutral Each 10 ₹ 643.00 ₹ 6,430.00

Digitally signed by JAYA

117 2.10.5 Triple pole and neutral Each 1 ₹ 1,301.00 ₹ 1,301.00

Supplying and fixing following rating, Double pole, 240 V, isolator in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing following rating, Double pole, (single phase and neutral), 240 volts, residual current circuit breaker

125 2.14 (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning ₹ -

etc. as required

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous

enamelled white on both sides, and with inscription in single red colour on front side as required.

135 Hot Dipped Galvanized Iron Cable Tray ₹ -

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less

than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from

the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

137 4.6.1 100 mm width X 50 mm depth X 1.6 mm thickness Meter 10 ₹ 754.00 ₹ 7,540.00

138 4.6.2 150 mm width X 50 mm depth X 1.6 mm thickness Meter 20 ₹ 803.00 ₹ 16,060.00

139 4.6.3 225 mm width X 50 mm depth X 1.6 mm thickness Meter 20 ₹ 991.00 ₹ 19,820.00

140 4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness Meter 30 ₹ 1,062.00 ₹ 31,860.00

145 EARTHING ₹ -

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover

plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with

147 5.4 cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required. Set 4 ₹ 8,351.00 ₹ 33,404.00

Supplying and laying 6 SWG G.I. wire at 0.50 Meter below ground level for conductor earth electrode, including connection/

termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/

151 5.9 terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. Meter 50 ₹ 160.00 ₹ 8,000.00

nut bolt & spring washer spaced at 50mm)

152 LIGHTNING CONDUCTOR ₹ -

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top,

with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

154 6.2 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. Each 4 ₹ 422.00 ₹ 1,688.00

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut

bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as

required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as

required.(For vertical run)

Digitally signed by JAYA

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck

nuts and spring washers etc. complete as required.

161 6.11 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. Meter 10 ₹ 221.00 ₹ 2,210.00

162 6.12 Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. Meter 10 ₹ 96.00 ₹ 960.00

163 LIGHTING CONTROLS ₹ -

Supplying, Installation, Testing and commissioning of Passive Infrared (PIR) technology based occupancy sensor having high

performance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 3

meter and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete

Supplying, Installation, Testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor with day

light dimming(lighting level shall be regulated as per availability of natural day light in an area along with occupancy

165 7.2 detection.) having high performance, regulating programmable type, suitable for connected load upto 10Amp , for Each 2 ₹ 9,670.00 ₹ 19,340.00

mounting height up to 3 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming

at site etc. complete as required.

166 LED LIGHT AND FAN ₹ -

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt )

Supplying, Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD

type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the

requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -

50C to 400C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI

>80,UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of

minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K / 6500°K

(As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the

specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System

lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS

shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C)

Powder coated die cast /Extruded aluminium Body including trim

Digitally signed by JAYA

LED Down lighter (COB Type) (System lumen efficacy ≥105 < 120 lm/Watt ).

Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) COB

Type of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency

>85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge

protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P.F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating)<

19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours

with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM

(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and

Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen

printing on housing Complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper

conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105

and <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.

Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of

aluminium housing such that LED junction temperature shall not rise above 90°C)

Powder coated die cast /Extruded aluminium Body including trim with Aluminium Reflector

LED Panel light 2x2 ft. (System lumen efficacy ≥105 <120 lm/Watt)

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS :

10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60

hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD <

10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,

Driver & electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends as per

LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard

Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall

181 8.6 be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete ₹ -

in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and

earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 &

LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as

approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED

junction temperature shall not rise above 90°C).

Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

Digitally signed by JAYA

LED Batten light (System lumen efficacy ≥105 <120 lm/Watt).

Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and

construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with

Short & Open circuit protection, THD < 10%, P.F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time

(LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT

3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power

consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word

186 8.9 Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq ₹ -

mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥105 <120 lm/Watt)

Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body

with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz,

Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency

>85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI

EMC As per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project

requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning

Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K /

4000°K / 5700°K /6500°K (As per ANSI Bin),SDCM (Standard Deviation Colour Matching) <5, Maximum power consumption

should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external

connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output .LM79 & LM80 Test report and all

testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-

Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature

shall not rise above 90°C)

Digitally signed by JAYA

LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy ≥105 <120 lm/Watt).

Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die cast aluminium body with built

in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC,

frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5,

Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage

protection, EMI-EMC as per CISPR -15, lenses for beam angle 30 deg-120deg as per the application and the project

requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with

70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K /4000°K / 5700°K

195 8.15 /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more ₹ -

than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with

1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year

OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output .LM79 & LM80 Test report and all testing required for LED

fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C)

200 Solar outdoor LED light ₹ -

Supplying, installation, Testing & Commissioning of the integrated type solar PV lighting system on the existing pole

structure, comprising of 30 watt, 6V Mono Passivated Emitter and Rear Contact (PERC) Solar Panel (minimum efficiency

21%), Pulse with modulation (PWM)/Maximum Power point tracking (MPPT) charge Controller in the box with a sleek

appearance and a sturdy structure, is weather-proof, and is simple to install, With Lithium- Iron Phosphate Battery

(LiFePO4), charging time 8-10 hours, Battery backup time 12 hours (minimum), LED fixture watt 30 watt, Input voltage: 12V

DC , Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency

>85%, IP-66,IK-08, CRI >70 , under voltage and over voltage protection, Electro Magnetic Interference (EMI) Electro

Magnetic Compatibility (EMC) As per CISPER 15 A, lenses for beam angle as per Illuminating Engineering Society of North

America (IESNA) type I/II/III as per the width of the road and the project requirement, Correlated Colour Temperature (CCT)

5700°K (As per American National Standard Institute (ANSI Bin)) , life time (LED,Driver & electrical circuitary) of 50K hours

201 8.21.2 lamp buring hours till the 70 % of initial Lumen maintained as per LM80 extrapolation IES TM-21-11 report, automatic swich Nos. 1 ₹ 23,100.00 ₹ 23,100.00

on/off, Alliuminium or Acrylonitrile Butadiene Styrene (ABS body), can be installed on a pole or wall. System lumen efficacy

>120 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. All as

per pre approved by Engineer in-charge complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as required, complete with mounting structure for the

battery and accessories suitable for withstand wind storm speed as per the site location. (Thermal management: heat sink

of aluminium housing such that LED junction temperature shall not rise above 90°C).

30 Watt (System lumen efficacy >120 lm/Watt)

Digitally signed by JAYA

Brush Less Direct Current (BLDC) Fan with Remote

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of

insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper

winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as

per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control

9.1 and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance

more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/c

external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as

9.1.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) Each 36 ₹ 2,882.00 ₹ 1,03,752.00

9.1.4 1400mm, service value ≥ 6.0 CM/Min/Watt, air delivery 245 CM/Min (Minimum) Each 12 ₹ 2,913.00 ₹ 34,956.00

Brush Less Direct Current (BLDC) Fan without Remote

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of

insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper

winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as

202 9.2 per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control ₹ -

and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance

more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c

external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as

203 9.2.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) Each 12 ₹ 2,695.00 ₹ 32,340.00

204 MV CABLE LAYING ₹ -

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground

205 10.1 including excavation, sand cushioning, protective covering and refilling the trench etc as required. ₹ -

207 10.1.2 Above 35 sq. mm and upto 95 sq. mm Meter 30 ₹ 475.00 ₹ 14,250.00

208 10.1.3 Above 95 sq. mm and upto 185 sq. mm Meter 30 ₹ 497.00 ₹ 14,910.00

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size

210 10.2 direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective ₹ -

covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing

RCC/ HUME/ METAL pipe as required.

217 10.5.2 Above 35 sq. mm and upto 95 sq. mm Meter 20 ₹ 72.00 ₹ 1,440.00

218 10.5.3 Above 95 sq. mm and upto 185 sq. mm Meter 30 ₹ 97.00 ₹ 2,910.00

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on

cable tray as required.

221 10.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Meter 20 ₹ 53.00 ₹ 1,060.00

222 10.8.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) Meter 20 ₹ 109.00 ₹ 2,180.00

Digitally signed by JAYA

223 10.8.3 Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) Meter 20 ₹ 138.00 ₹ 2,760.00

224 10.8.4 Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) Meter 30 ₹ 226.00 ₹ 6,780.00

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate

225 10.9 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including Each 10 ₹ 683.00 ₹ 6,830.00

inscription duly engraved as required.

226 MV CABLE JOINTING & END TERMINATION ₹ -

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC

insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

MISC. ITEMS ₹ -

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with

246 15.14 cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. ₹ -

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level)

including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as

286 26.1 Online UPS - Input supply: Single Phase, Output Supply : Single Phase ₹ -

Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) ON LINE

Uninterrupted Power Supply (UPS) system suitable for Single Phase input, Single Phase output AC Supply. The UPS shall

include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600

VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static

Bypass switch along with provision for manual bypass, suitable isolation transformer for additional protection against

neutral faults etc. The UPS systems shall be Microprocessor based Digital Control, using Insulated Gate Bipolar Transistor

(IGBT)'s both for the rectifier & inverter with PWM (Pulse Width Modulation) Technology. The quality of design,

287 manufacturing and inspection process should confirm to the relevant Inter-national standards such as IEC/EN/VDE. The ₹ -

operating efficiency of the UPS systems shall be >95% at 100% non-linear loads. Current total harmonic distortion (ITHD)/

total demand distortion (TDD) on the input grid shall be < 5% at 100 %load. (The required LC filters shall be included in UPS

cost), extreme power factor kit to be include to limit the input pf to 0.99 and output power factor shall be unity (i.e. kw

rating of the UPS shall be kva rating x 1 ) however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor

loads. UPS shall be suitable for incoming supply AC single phase 160-270V 50 Hz and delivering output AC supply true sine

wave single phase 220/230/240 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins and 150% for 1 minute.

Digitally signed by JAYA

Operating temperature 0 to 40 deg C, Relative humidity 0-95% non condensing, noise level less than 60db at 1 meter

distance, Protection for Under voltage, over voltage, abnormal output voltage, battery over charging, output over current,

short circuit, battery deep discharge , 10 KV surge. Display for watt/VA,Amp and Voltage power parameters etc. UPS shall

comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be

a Voltage and Frequency Independent (VFI) type UPS (as per standard IEC 62040-1, 2 & 3) . The UPS should be with IGBT

288 Based Inverter Technology, Communication RS232/RS485/SNMP port open protocol for BMS integration as per approved by ₹ -

Engineering in charge. Required battery racks, DC breaker of suitable rating and interconnecting copper conductor cable of

suitable size and connectors and all required accoseries are inclusive in the cost. The UPS should have QR code which should

contain drawing, test report OEM manual, Geo- Tag of manufacturing location etc

Supplying, Installation, Testing & Commissioning of following capacity passenger Machine room less (MRL) lift with

regenerative drive as per CPWD General Specification for Electrical Works (Part-III Lift & Escalator) 2003, BIS Codes, NBC

2016 as amended upto date having provision for barrier free access as per Harmonised Guidelines & Standards for Universal

Accessibility in India - 2021 of MoHUA, serving different floors in the lift shaft as per detailed specifications enclosed and as

under including all other equipment and accessories complete as required:-

(i) Speed-1 MPS

(ii) Floors- (G+2)

(iii) Travel -12 Meters (approx.)

(iv) Stops & opening- 3 stops and 3 openings

(v) Controller: A.C. variable voltage & variable frequency

(vi) Automatic rescue device (ARD) complete with dry maintenance free batteries as required.

vii) Operation: Microprocessor based single automatic push button/simplex selective collective/duplex collective selective

with/without attendant

(viii) Power-415 Volts+10%, 3 phase, 50 Hz, 4 wires system

(ix) Car Enclosure: Stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish) on all sides and stainless steel

decorative ceiling with fans (indirect throw) and LED fitting.

(x) The car flooring should be smooth and antiskid as approved by engineer-in-charge.

(xi) Type of doors

(a) Car: Power operated, centre opening horizontal sliding stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline

(b) Landing doors: stainless steel scratch proof .

Digitally signed by JAYA

(xii) A hand rail not less that 600mm long at 900mm above floor level to be fixed adjacent to control panel in the lift car.

(xiii)Voice announcement system in the car to announce the position of the elevator in the hoist way as the car passes or

stops at floor served by the elevator.

(xiv) Closed loop Control System, protection against power fluctuation, self diagnostic control, Landing doors 2 hours Fire

rated, Overload detection and protection, Overspeed Governer, Dot Matrix LED D & P Indicators In Car & Landings, BMS

Compatibility, tamper proof infrared curtain covering almost the entire height of the lift car door, Alarm horn, Anti Nuisance

Operation, CCTV camera system with 4 MP IP camera, suitable NVR and HDD for 30 days storage backup , Firemen switch,

2/3 way intercom, Emergency Stop Switch with battery backup for fan and light fitting for 1 hour, pit ladder. ₹ -

(xv) The lift doors shall have a vision panel to enable persons with hearing impairment to signal for help or assistance in the

event of an emergency.

(xvi) An appropriate technological support be provided (Through emergency messaging |services or alarms etc.) to respond

to the emergency requirements of person with hearing impairment or deafness.

(xvii) In case of failure of ARD or other electronic devices, a provision of manual rescue be provided

SOLAR WATER HEATING SYSTEM

Supply, Installation, Testing & Commissioning of Flat Plate collector (FPC) Solar Water Heating System comprising of solar

flat plate collector ISI Marked made of copper sheet/copper tube, absorber toughened glass cover and aluminium extruded

channel confirm to IS: 12933 (Part 1,2,3&5). The system shall have temperature gauges, strainer, water meter 2 nos., cold

and hot water tank. The system shall have suitable electric backup complete with control and power wiring etc., as

1. Cover plate: cover plate shall be toughened glass and thickness of 4.0 mm (min) conforming to section -1 of IS: 12933(pt-

2)/2003 the solar transmittances of the cover plate shall be minimum 82 percent at near normal incidence.

2. Collector box: collector box shall be made of aluminium sections. The type grade, size, and finish of the material used

shall be as per section-2 of IS: 12933 (pt-2)/2003: the minimum thickness of aluminium shall be as under:

16.2 a. Channel section for sides 1.6 mm ₹ -

b. Sheet for bottom 0.7 mm

c. Support for glass retaining 1.2 mm

d. Sheet for entire body 1.0 mm

The insulation of collector box shall be minimum 0.96 sq.m 0C/W for back insulation and minimum 0.48 m square degree

c/w for side insulation conform to sec. 4 of IS 12933 (Part – 2) / 2003. (b) Gaskets and grommets: gaskets and grommets

shall conform to Sec. 5 of IS 12933 (pt-2)/2003.

Digitally signed by JAYA

3.Absorber Shall Consist of riser, Header and Sheet for absorber. The Diameter of header shall be 25.4 + /-0.5mm and

thickness 0.71mm. The Diameter of riser shall be 12.7 + /-0.5 mm and thickness 0.56mm and made of copper only. The

distance between the risers from centre to centre shall be 120mm. type grade, size , workmanship and finish of the material

used shall be as per section- 3 of IS : 12933 (pt -2 ) /2003 the sheet for absorber shall be of copper sheet 34 gauge/copper

tube (at least 10 nos.)

4.Riser and header assembly designed for working pressure up 245 k pa (2.5 kg/ cm square) shall be tested for leakage at a

minimum hydraulic pressure of 490 k pa (5 kg/ cm square). Sheet for absorber shall be made of copper only. Type Grade,

size, workmanship and finis of the material used shall be per Section -3 of IS: 12933 (pt -2) /2003. ₹ -

5.HDPE/LDPE cold water tank and hot water tank shall be dully erected on MS angle /channel duly painted with dual coats

of enamel paint. The overall structure of solar collector plate module shall be design to with stand wind velocity of 100 kms

/hr (minimum) or more as per site.

6.Hot water tank : The tank capacity shall be minimum 1.25 time the rated capacity of system. Inner tank material shall be

stainless steel SS 316, as per IS 1730 GRADE SS304-2B. Hot water shall be insulated with high density injected PUF

insulation: 50 mm, of 50 mm thickness between inner and outer tank ensures maximum heat rotenone ever season.

7. Suitable nos. ISI Marked electrical heaters along control panel, suitable breaker all protections, and all safety provisions

so as to achieve 600C temperature rise in an hour. The range of thermostat shall be upto 800C.

TOTAL AMOUNT AS PER DSR (Rs.) ₹ 91,71,271.72

TOTAL AMOUNT AS PER DSR (Rs.) ₹ 91,71,271.72

1 MR-1 Electrical Floor Panel ₹ -

Supplying, installation, testing & commissioning of cubical type LT Indoor Panel Board for 415V, 3 Phase, 4 Wire,

50 Hz AC supply system of suitable size fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick

for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for

7.1 powder coating in approved shade, having 300 A capacity extensible type four strip aluminium bus bars of high ₹ -

conductivity, DMC / SMC bus bar supports, bottom base channel of MS section not less than 75 mmx 50 mm x 5

mm thick, entire panel shall have a common GI earth bar 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections

from main bus bar to switch gears with required size of aluminium bus bars and control wiring with 2.5 sq. mm.

PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c providing and fixing of following ₹ -

switchgear and components complete as required.

1) 315 A, FP, 25 kA, thermo magnetic release type MCCB with

spreader link & ROH - 01 No.

2)1 set of 150/5 A ratio CTs ₹ -

3)1 Set of LED type indicating lamps(RYB) with 2 Amps SP

MCBs for Instrument Protection

4)Multi Function Meter -1 no ₹ -

(II) Busbars and their ratings ₹ -

400 A 4 strip aluminum busbars - 100 % Neutral ₹ -

2) 1 Phase Energy Meter- 14 Nos

3) 63 A, DP, MCB 10 kA - 03 Nos

Digitally signed by JAYA

S/I/T/C of 1.1 KV grade PVC insulated PVC sheathed XLPE Aluminium conductor armoured cable conforming to IS:1554 Part-

I of the following sizes.

Supply, Installation testing & Commissioning of 400 MM Sweep Size 1350:RPM Aerodynamic Blade Design for High Air

MR- 3 Delivery Anti - Rust Protection 100% Copper Motor Wall Fan with Thermal overload protection, minimum 3 Speed Settings Nos 1 ₹ 3,600.00 ₹ 3,600.00

and Pull Chord Mechanism for easy control

Supply and fixing of 7.0 Mtrs G.I. Octagonal Pole (70 mm A/F(Top) x 130 mm A/F (Bottom) single arm for street light with

base plate of 250 x 250 x 16 mm, 4 nos. 600 mm long M20 foundation bolts & hardwares (suitable reinforcements to be

inserted in the foundation and 40mm x 2 nos. GI pipes for In/Out of maincables) Any other accessories etc. required

complete in all respect as per direction of Engineer in charge. The pole shall also be provided with recessed lockable GI

junction box of suitable size and flush door and MCB at the bottom with properstrengthening for the cutout of the door

opening of junction box.

Supplying,installation,testing and commissioning of LED 10 watt mirror light fitting With extruded polycarbonate

housing, High optically efficient diffuser, above wash basin complete with all accessories etc. directly on wall,

including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core

cable and earthing etc. as required.

SITC of wall surface mounting bed Lamp, CR Body/White Diffuser having Warm Light bulb of IP 20 protection and IK 07 etc

complete in all respect.

MR-7 SITC of 10 W Study Light 5700k, SS Body, IK 07 Complete in all respect. Each 12 ₹ 1,850.00 ₹ 22,200.00

Supply of Exhaust fan 300 mm sweep metal body with 50 HZ 230 volt ac complete with all respective

MR-9 SITC of 10 W, Bulk Head 5700k, IP 56, IK 08 Cpmplete in all respect Each 10.00 ₹ 1,620.00 ₹ 16,200.00

Supply, Installation, Testing, & Commissioning (SITC) of 10-litre capacity Gyster of 4 to 5-star rated, 2 kW electric

storage water heater with glass-lined tank, 8-bar pressure rating, PUF insulation, Incoloy heating element, and all

standard safety features and accessories as per technical specifications and the direction of the Engineer-in-

Supply and laying of 3 core 25 sq mm XLPE insulated, copper conductor cable, 1100 Volt grade. Shall conform to

IS 694: 2010 (latest edition) for flexible cables, and IS 8130 for conductors.

Total (NS) amount Rs. ₹ 25,20,399.40

Digitally signed by JAYA

DSR 2025 Descriptions Rate (Incl.

Sl. No. Unit Qty Amount (Rs.)

FIRE FIGHTING SYSTEM

(a) Supplying, installation, testing and commissioning of electric driven terrace pump

conforming to IS 12469: 2019 suitable for automatic operation and consisting of

following, complete in all respects, as required: (Terrace Pump)

(b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body &

bronze impeller with stainless steel shaft, mechanical seal as required.

(c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415

1 27.4 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, ₹ -

horiziontal foot mounted type with Class-'F' insulation, conforming to IS-12615:

(d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts

etc.as required.

(e) Suitable cement concrete foundation duly plastered and with anti vibration pads.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming

to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges,

4 27.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable ₹ -

clamp/support frame and painting with two or more coats of synthetic enamel paint

of required shade complete as required :

Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe

conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers,

9 27.8 nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable ₹ -

clamp/support frame and painting with two or more coats of synthetic enamel paint

of required shade complete as required :

Supplying and fixing single headed internal hydrant valve with instantaneous

Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked

conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as

14 27.9.2 Single headed Stainless steel Each 4 ₹ 6,632.00 ₹ 26,528.00

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with

15 27.11 bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets ₹ -

conforming to IS 13095 of following sizes as required :

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304)

with orifice of required size to be fitted between flange & landing valve of external

and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2

complete as required.

Providing, installation, testing and commissioning of non-return valve of following

27.14 sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers

etc.as required :

Providing, installation, testing and commissioning of stainless steel Y-strainer

27.15 fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes

with stainless steel flange.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and

19 27.16 female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as ₹ -

21 27.16.2 Stainless Steel (Grade 304) Each 6 ₹ 4,667.00 ₹ 28,002.00

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post

office red, conforming to IS 884 complete with the following as required.

(a) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2

as per IS: 12585

(b) 20 mm nominal internal dia gun metal globe valve & nozzle.

(c) Drum and brackets for fixing the equipmets on wall.

(d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal

25 27.18 internal diameter size nozzle conforming to IS 903 suitable for instantaneous ₹ -

connection to interconnect hose pipe coupling as required:

27 27.18.2 Stainless Steel (Grade 304) Each 2 ₹ 3,402.00 ₹ 6,804.00

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm

in height with air release valve on top and flanged connection to riser, drain

28 27.20 arrangement with 25 mm dia gun metal wheel valve with required accessories, Each 1 ₹ 19,402.00 ₹ 19,402.00

pressure gauge and painting with synthetic enamel paint of approved shade as

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as

33 FIRE DETECTION AND ALARM SYSTEM ₹ -

Supplying, installation, testing & commissioning of manual call boxes of MS

34 28.1.3 construction in surface/recess with stainless steel chain & hammer assembly Each 4 ₹ 513.00 ₹ 2,052.00

complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning of manual call box of ABS type in

35 28.1.4 surface/recess with stainless steel chain & hammer assembly complete with glass Each 8 ₹ 444.00 ₹ 3,552.00

and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to

make announcement, mounted in M.S. box (16 SWG) with hinged cover plate &

suitable for operation with amplifier i/c line matching transformer etc. complete as

Supplying, installation, testing & commissioning fire alarm sounder with facility to

make announcement, mounted in A.B.S. box with hinged cover plate & suitable for

operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning of main control and indicating panel

made out of 16 SWG MS sheet to accommodate the following items duly powder

coated in approved colour with louvers for ventilation, locking arrangement, audio

and visual indication for fire alarm and public address system, monitoring system

including connections, interconnections etc complete as required.

10 Zone panel for fire alarm system 250 Watt amplifier racks suitable for operation

on 230V AC/24V DC supply conforming to IEC-268-3 complete with all accessories as

required - 2 Nos.(one to act as standby)

Talk back master station with LED PTT (press to talk) push button for operation on

230V AC/24 V DC supply conforming to IEC-268 for simplex mode of

operation/communication suitable for 20 Nos.talk back unit -1 set.

Announcement control desk suitable for selection of different zones selectively and

ON ALL CALL switch with visual indication etc. complete as required -1 set.

Amplifier change over switch for inter changing amplifier -1 No.

Monitor panel for loudspeaker complete with output selector, ON/OFF switch, fuse,

visual indications etc. complete as required- 1 No.

Gooseneck microphone with stand and ON/OFF switch- 1 No.

Main ON/OFF switch, fuse indication lamps, DC and AC voltmeters & ammeters,

terminal blocks etc. complete as required -1 set.

Battery charger trickle cum boost to take complete load of fire alarm & PA system

complete with all accessories including providing & fixing of 2 nos.12 volt, 60 AH each

sealed maintenance free batteries -1 set.

Supplying, installation, testing & commissioning of addressable phone control

module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point

complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe

complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset

complete as required.

Supplying, installation, testing & commissioning of intelligent interface unit BACnet/

Modbus protocol i.e. supplying communication links between building management

system and fire alarm control panel complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated

with annealed copper conductor having glass mica fire barrier tape covered by an

45 28.5. extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and Meter 100 ₹ 386.00 ₹ 38,600.00

LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank,

18.48 Civil ISI : 12701 marked, with cover and suitable locking arrangement and making

Vol-II necessary holes for inlet, outlet and overflow pipes but without fittings and the base

support for tank.

47 Total (DSR) Amount Rs. ₹ 10,08,172.00

48 NON Schedule tems

49 Tarrace Pump Panel

Design, manufacture, supplying, fixing in position, testing and commissioning of the

following front operated cubicle type, front access 2mm thick mild steel sheet, free

standing, dust and vermin proof, switchboard with IP42 protection with hinged and

lockable doors complete with interconnections, tinned copper crimping lugs, bonding

to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system and

50 MR-1 suitable for a fault level of 25 MVA symmetrical at 415 volts. MCC for Fire Fighting Each 1 ₹ 92,850.00 ₹ 92,850.00

Pumps at Terrace

i) All interconnecting power & control wires/cables suitable size within the panel

and from panel to motors , pressure switches, level switches, cable Tray, pipes

etc. including brass glands termination within fire pump house and earthing as

per specifications.

Total (NS) Amount Rs. ₹ 92,850.00

Rate (Incl. 18%

Sl. No. DSR 2025 /MR Descriptions Unit Qty Amount (Rs.)

Supplying Installation Testing and Commissioning of 4MP IP IR Dome Camera having following

specifications and features etc :-

1) Signal System: PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date &

Time in live & recorded video

2)Image Sensor: 1/2.8" or better progressive ScanCMOS to get color image even at night

condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night

High Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt

IR LED's with effective distance upto 50 meter or better and 30 meter for colour view in night, Imaging:

1/3s to 1/30000s electronic shutter support, Auto Gain Control , White Balance- Auto, Back Light

Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking.

3) Compression (Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723

4) Wide Dynamic Range:- WDR (120dB or more)

5) Digital Noise Reduction:- DNR (3D) On/Off

6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream: 4MP

(2560×1440)25/30fps , Sub streams minimum: 720P@25/30 fps 7) Image Setting: Rotate Mode,

saturation, brightness, contrast, sharpness adjustable through client software or web browser, Edge

Analytics: Tripwire, Intrusion, Motion Detection

8) Cyber Security: AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security

logs, account lockout, video encryption, IP/MAC filtering, HTTPS, trusted upgrade

9) Onboard Storage: Camera should support built-in Micro SD/ SDHC/ SDXC Card slot upto 512 GB. It

should be supplied with minimum 128GB memory Card.

10) Recording Management: Format SD, overwrite, storage management, video to NAS device,

11) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection;

memory card state detection; memory space detection

12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS,

UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,

13) System Capability: ONVIF, Camera shall support open source VMS

14) Ethernet: 1 RJ 45 10/100 Ethernet port

2 15) Audio : It should support 1 x Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per

site requirement.

16) Power Input: The camera should support simultaneous dual power input—12 VDC (via power adapter)

and PoE (802.3af)—to ensure continuous operation in the event of a failure in one power source.

17) Power Requirement: 12VDC/24 VDC/PoE (802.3af)/ePoE

18) Housing/ Enclosure:- IP67 weather proof, IK10, Metallic body

19) Operating Condition:- Ambient Temperature:- (- )05°C to 50°C, humidity 95% (max) (non-condensing)

20) IR life: 40000 hours or higher

21) Video Bit rate: 32 KBPS - 8 MBPS or better

22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

4MP @ 25/30fps@1440P (2560 x 1440) Dome Camera with 2.8/ 3.6/ 6/8/12 mm fixed lens (as per site

Supplying Installation Testing and Commissioning of 4MP IP IR Outdoor Bullet Camera having following

specifications and features etc :-

1) Signal System: PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date &

Time in live & recorded video

2)Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night

condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night High

Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR

LED's with effective distance upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s

to 1/30000s electronic shutter support, Auto Gain Control , White Balance- Auto, Back Light

Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking.

3) Compression (Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723

4) Wide Dynamic Range:- WDR (120dB or more)

5) Digital Noise Reduction:- DNR (3D) On/Off

6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream: 4MP

(2560×1440)25/30fps Sub streams minimum: 720P@25/30 fps

7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client

software or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection

8) Cyber Security: AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security

logs, account lockout, video encryption, IP/MAC filtering, HTTPS, trusted upgrade

9) Onboard Storage: Camera should support built-in Micro SD/ SDHC/ SDXC Card slot upto 512 GB. It

should be supplied with minimum 128GB memory Card.

10) Recording Management: Format SD, overwrite, storage management, video to NAS device,

11) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection;

memory card state detection; memory space detection

12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS,

UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,

13) System Capability: ONVIF, Camera shall support open source VMS

14) Ethernet: 1 RJ 45 10/100 Ethernet port

6 15) Audio : It should support 1 x Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per ₹ -

site requirement.

16) Power Input: The camera should support simultaneous dual power input—12 VDC (via power adapter)

and PoE (802.3af)—to ensure continuous operation in the event of a failure in one power source.

17) Power Requirement: 12VDC/24 VDC/PoE (802.3af)/ePoE

18) Housing/ Enclosure:- IP67 weather proof, IK10, Metallic body

19) Operating Condition:- Ambient Temperature:- (- )05°C to 50°C, humidity 95% (max) (non-condensing)

20) IR life: 40000 hours or higher

21) Video Bit rate: 32 KBPS - 8 MBPS or better

22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

4MP @ 25/30fps@1440P (2560 x 1440) Outdoor Bullet Camera with 2.8/ 3.6/6/8/12 mm fixed lens (as

per site requirement)

Supplying Installation Testing and Commissioning of following Channel Network Video Recorder (NVR)

with camera licenses to record for all channels having specifications and features etc as mentioned below

1) Network Video Recorder Embedded/ Installed OS (Linux) along with Camera Licenses to record per NVR

and to provide a live view, storage and simultaneously Multi-channel playback of all IP camera or more

and must be ONVIF with minimum support of 384 Mbps incoming Bandwidth.

2) NVR should support video compressions : H.265 or better, H.264, MJPEG.

3) Must support 1 channel RCA Input, 2 channel RCA Output for Two-way Talk with G.711U/A, G.711u,

PCM, G726 audio compressions.

4) Intelligent auto power on when power resumes after power outage.

5) Storage: It should support minimum 8 SATA Slots with 20TB capacity/ Slot and RAID support of RAID

6) Connectivity Interface : 2 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x RS232, 1x eSATA Port

13 40.11 7) Backup Interface : Its should have 4 Nosx USB port (2x USB3.0, 2xUSB2.0) ₹ -

8) Video Output Ports: 2x HDMI and 2 VGA

9) Alarm Ports: It should have 16/8 Ch In/ Out ports to connect various type of external sensors and

output devices like hooter/ Siren etc.

10) Email & SMS Altert options: Option for SMS/ Email Alerts to minimum 5 designated mobile number

for power failure, HDD failure, vandalism, tempring, network disconnection and panic

11) Web & Mobile Application: Web, Mobile app ( For iPhone, iPad, Android Phone) for alerts and

12) Protocols: HTTP, HTTPS, TCP/IP, IPv4/IPv6, UDP, DHCP, DNS, SMTP, UPnP, IP Filter, PPPoE, FTP, DDNS,

Alarm Server, IP Search, Multicast, Auto Registration, ONVIF (Profile T, Profile S, Profile G), CGI, SDK and

OEM Cloud for remote monitoring without any public IP need.

13) Standards: CE, FCC, RoHS, BIS Certified

14) Power Supply : Should support AC100-240V, 50/60Hz Power supply.

15) Operating Condition : -5°C to 50°C, humidity 90% (max) (non-condensing)

16) The VMS application shall support all the features & functionalities of the offered cameras.

17) VMS should consist Licenses for all channels to record Cameras with General, motion detection,

intelligent, alarm and POS recording modes. VMS should be provided with Camera Licenses , with no

dependency of VMS licenses by binding with the MAC address of the cameras to achieve the functionality.

18) The NVR OEM shall be responsible for providing a mobile application compatible with both Android

and iOS devices, enabling remote monitoring and playback of cameras/NVR footage.

19) The OEM must provide its own DDNS server hosted in India, eliminating the need for a public IP

address for remote monitoring over the Internet.

20) Must support Continuous, Alarm, Motion, Instant, Panic Recording Mode

21) It should support Resolution: 32MP; 24MP; 16MP; 12MP; 8MP; 5MP; 4MP; 1080p; 720p; D1; CIF;

14 22) When alarm recording is enabled and an event occurs, you can click the alarm icon on monitoring ₹ -

page to view the alert details. The snapshot function is supported on monitoring and playback page

23) The Network Video Recorder (NVR) shall be configured to send email whenever a system message is

created or an alarm event occurs. The email server shall be a valid SMTP server. Each recipient email

address shall be configured to receive any combination of critical, warning, or informational messages or

alarm notifications. When an alarm occurs, the email message includes the NVR name, time of alarm and

a list of camera that is configured to record upon alarm

24) It should have Web and GUI interface.

25) Built-In Artificial Intelligence: NVR should have built-in AI :- - 2 Channel face detection and

recognition, - Minimum 4 Channel perimeter protection, - Minimum 8 Channel Smart Motion Detection

26) Face Recognition Database Capacity: It should support total Blacklist and Whitelist capacity of

Minimum 20,000 Faces or more with Face Detection speed of 12 face images/sec and facility to add

Name, gender, birthday, address, credential type, credential No., countries & regions and state to each

27) Face & Human Attributes Search: Search Pictures/ Video by Gender, age group, glasses, expressions,

face mask, beard, Top color, top type, hat, bag, age, gender and umbrella.

28) ANPR Capability: It should support ANPR Camera with License plate, plate color, vehicle body, vehicle

model, vehicle logo, calling, seatbelt, vehicle registration location etc vehicle attributes.

29) Alarm Notifications based on: Motion detection, video tampering, video loss, scene changing, PIR

alarm, Camera external alarm, Face detection, face recognition, perimeter protection (intrusion and

tripwire), ANPR, people counting, stereo analysis, crowd distribution, heat map, Disk Full, Storage Error, IP

Conflict and abnormal behavior of fan, cybersecurity exception

30) Alarm Notification should be linked with Recording, snapshots, Camera external alarm output, buzzer,

logs, presets and email.

31) General AI Based Search: Search Pictures by channel, time, event type, target classification (Fall

Detection, People Approach Detection, People No. Exception Detection, People Staying Detection,

Violence Detection.

32) Smart playback function: Should support smart search for the selected area in the video and smart

playback to improve the playback efficiency

33) VCA (Video Content Analytic): Should support multiple video contented analytics based on camera

34) Analytics by NVR: Perimeter protection and face recognation

32 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16/25/32(36),

2nd screen: 1/4/8/9/16

17 Hard Disk Drive ₹ -

Supplying, Installation, Testing and Commissioning following capacity Serveillance grade Hard Disk with

upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 inch form factor, SATA Interface,

BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA, VCCI, CB-Scheme, TUV, UL Certifications.

Supplying, installation, Testing and commissioning of following capacity 24 port Layer 2 indoor Network

Switch having features and specifications etc. as mentioned here under: At least 24 X RJ-45 Gigabit

Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking architecture by having

Switching capacity of min. 168Gbps and packet forwarding rate of 125Mpps or higher, 16K MAC table.

Console Port, USB port, Stacking support of min. 8 units per stack. Internal dual AC Power supply, STP,

RSTP, MSTP, BPDU Filter, BPDU Restriction, Min. 9K Jumbo Frame, LBD, IGMP Snooping V1/V2/V3, MLD

Snopping V1/V2. IGMP /MLD Groups 1K or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6

ND, VRRPv3, UDP Helper, ECMP. VLAN: 802.1Ǫ, Port based, Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN, VLAN

Trunking, DHCP Snopping, Server, server Screening. RADIUS , TACACS+ Authentication, ǪoS: 802.1P, 8

queues per port, ǪoS : WRR, Strict+WRR, WRED, 802.1p. ACL: MAC based, IPv4C IPv6, TCP/UDP Port

number, time based ACL, TFTP Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client,

LLDP, LLDP-MED, OAM, Dying Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV

surge protection on all Gigabit Ethernet ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC,

RoHS, MTCTE, OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication,

Government of India etc. complete as required

24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each copper port

supporting 802.3at PoE+ min.

Supplying, Installation, Testing and commissioning of small form-Pluggable (SFP) for Network Switches.

Must be hot Pluggable, RoHS Complaint, etc. complete as required.

23 39.6.1 1G SFP Single Mode/Multi Mode Each 2 ₹ 4,211.0 ₹ 8,422.0

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded. Must be of 1U

height with clear label holders and white label with the panel. 24 Ports Cat-6 Patch Panel should have

TL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6 Patch Cord should have ETL/UL

27 39.12 verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required. ₹ -

28 39.12.1 Copper Patch Cords of length 1m (3ft) Each 15 ₹ 151.0 ₹ 2,265.0

Supplying, Installation, Testing and commissioning of CAT6 Copper Information Outlet (IO) with face plate

of color as per site requirement, should have ETL/UL verification program certificate for compliance with

ANSI/TIA-568.2-D. All copper Cable and Components should be from same OEM to maintain compatibility

and interoperability etc. complete as required.

Supplying, Installation, Testing and commissioning of RJ45 Connector for CAT 6/6A Cables. RJ45 modular

31 39.16 plug supports 4 twisted pairs, 8 positions, 8 connectors. Housing: PC, UL94V-2, transparent color, Use for Each 10 ₹ 6.0 ₹ 60.0

24- 26 AWG stranded wires etc. complete as required.

Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted Pair Cable

in existing conduit/ on surface, ategory 6 Unshielded Twisted Pair, 4 pair should be complied as per

UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in

the range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C, Bending Radius : < 4 X

Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg etc. complete as required.

Supplying and drawing following core Multi mode Fiber Optic Cable having corrugated steel armoring,

leser optimize 50/125 µm with HDPE jacket, LSZH (Low smoke Zero Halogen), Tight-buffered or loose

tube, maximum attenuation: < 3.5 dB/km at 850 nm, < 1.5 dB/km at 1300 nm, bandwidth > 2000 MHz-km

at 850 nm, > 500 MHz-km at 1300 nm compliance and certifications: ISO/IEC 11801 Ed. 2.2, ANSI/TIA-568-

C.3, ITU-T G.651.1 RoHS compliant. Multi Mode Fiber shall be Central-loose tube filled with Thixotropic

jelly, duly following Standards: ISO 11801, IEC 60793-1/60794-1-2, ITU-T-REC G.652D and Telecordia GR-

37 39.20 20-core, High quality Electro Chromium Coated Corrugated Steel tape (ECCS ) and HDPE- Sheath, ₹ -

Operating ambient Temperature should be – 5 0C to +50 0C and Storage Temperature should be – 5 0C to

+50 0C, Maximum Attenuation ± 3.5 dB/km at Operational Wavelength 850 nm and ± 1.5 dB / km at

Operational Wavelength 1300 nm . type of fiber should be 50/125 / G.652D & Refractive Index should be

1.483/1.478, The value for Mode-filed,Cladding Diameter 50 ± 2.5 µm and 125 ± 1µm correspondingly i/c

splicing & marking etc complete as required.

38 39.20.1 6 Core Multi Mode Optical Fiber Cable Meter 500 ₹ 87.0 ₹ 43,500.0

Supply and fixing following port Rack Mount loaded LIU with pigtail, Front-mounted cable saddles for

jumper management, suitable to manage both splices and terminations, Pre-assembled shelves in

multiple configurations, Rubber fiber slotted bracket built-in, metal splice shelf to protect the fibers, 2

40 39.21 fiber spools built-in for 900μm tight buffered fiber storing, Capable of storing up to 3 meters of 900μm ₹ -

tight buffered fiber per adapter, Removable front and rear covers for better access to interior of LIU,

Should be Single / Multi mode LC Type fully loaded. Accessory kit consists of cable ties, mounting ear

screws, and spiral wrap tube etc complete as required.

Supplying and fixing Patch Cord of Optical Fiber Multi Mode or Single Mode LC to LC Fiber Duplex having

high precision ceramic ferrule with good concentricity, Fiber corning single mode G652D, Cable Type 2mm

with Mechanical specification Apex Offset < 50 µm, Fiber Height + 100 nm, End-face radius of Curvature

7mm < R <25mm, Repeatability < 0.2 db, Working ambient Temperature – 5 0C to +50 0C, Storage

Temperature – 10 0C to +50 0C, Length -- 2meter, Type -- LC-LC Duplex etc complete as required.

Supplying and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm CRCA Sheet,

completely knocked-down condition (CKD) Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking,

Minimum 2 cable entry/exit provision at Top and bottom with rubber protection, Front 5mm Toughened

Glass with lock, wall mounting kit, Powder coated Color- RAL- 7035, complied with UL & RoHS, 2 x 6

sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware mounting screws

packet of 20 x 1 number, etc. complete as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

49 1.21 surface/recess including cutting the wall and making good the same in case of recessed conduit as

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket,

bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in

ground (75 cm below ground level) including excavation and refilling the trench but excluding sand

cushioning and protective covering etc., complete as required.

55 Total (DSR) Amount Rs. ₹ 5,99,693.0

56 Non Schedule items

CPU: Supply, Installation, Testing & Commissioning of CPU with 13th Generation Intel Core i7-13700 Each ₹ 1,66,320.0 ₹ 1,66,320.0

57 MR-1 processor, Windows 11 Pro, Intel® UHD Graphics 770, 16 GB DDR5-4800 RAM, 1 TB SSD Solid State Drive, 1

Wired Keyboard, 1x VGA; 2x DisplayPort 1.4.

58 MR-2 42 inch LED Screen Each 1 ₹ 68,720.0 ₹ 68,720.0

Total (NS) Amount Rs. ₹ 2,35,040.0

DSR 2025 Rate (Incl. 18%

Sl. No. Descriptions Unit Qty Amount

Supplying, installation, Testing and commissioning of following capacity 24 port Layer 2 indoor Network

Switch having features and specifications etc. as mentioned here under: At least 24 X RJ-45 Gigabit Ethernet

Ports and additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking architecture by having Switching

capacity of min. 168Gbps and packet forwarding rate of 125Mpps or higher, 16K MAC table. Console Port,

USB port, Stacking support of min. 8 units per stack. Internal dual AC Power supply, STP, RSTP, MSTP, BPDU

Filter, BPDU Restriction, Min. 9K Jumbo Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP

/MLD Groups 1K or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ND, VRRPv3, UDP Helper,

ECMP. VLAN: 802.1Ǫ, Port based, Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN, VLAN Trunking, DHCP Snopping,

Server, server Screening. RADIUS , TACACS+ Authentication, ǪoS: 802.1P, 8 queues per port, ǪoS : WRR,

Strict+WRR, WRED, 802.1p. ACL: MAC based, IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP Client,

SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client, LLDP, LLDP-MED, OAM, Dying Gasp,

802.3ah, sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV surge protection on all Gigabit Ethernet

ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must be on

Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as

24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each copper port supporting

802.3at PoE+ min.

7 39.3.2 24 port Layer 2 Non-PoE Network Switch Each 2 ₹ 86,163.00 ₹ 1,72,326.00

Supplying, installation, Testing and commissioning of following capacity 24 port Layer 3 Network Switch

having features and specifications etc. as mentioned here under: At least 20 X RJ-45 Gigabit Ethernet Ports

and additional 4 combo 10/100/1000 base-t/SFP Ports with additional 4 SFP+ ports non-blocking architecture

by having Switching capacity of min. 128Gbps and packet forwarding rate of 95Mpps or higher, 16K MAC

table. Console Port, USB port, Internal AC Power supply with operating temperature of 0 to +50 0C. Stacking

port with stacking support of minimum 8 units per stack. 48K Mac address, 9K or more Jumbo frame, ERPS

with enabling ring to converge in less than 50 ms from node or link failure, Static routing, Static, 6to4, ISATAP

and GRE, IPv6 Neighbor Discovery (ND), BGP, ISIS, MPLS, VRRP v2, OSPFv2/v3, PBR, Route Redistribution,

RIPv1/v2/ng, IP Helper all L3 Protocols should support from day 1 for both IPv6 and IPv4, 802.1x, Port security

8 39.4 , Radius C TACACS+ authentication C accounting, DAD, DAI, DoS attack prevention, SSH, Guest VLAN, IP Access Each 1 ₹ 1,93,791.00 ₹ 1,93,791.00

List, MAC Access List. Multicast: VLAN, PIM-SM, PIM DM, PIM- SDM, PIM-SMv6, DVMRP v3 and MSDP, IGMP

C MLD Snooping, Flow mirroring, IGMP C MLD Snooping Ǫuerier, Per-VLAN IGMP C MLD Snooping.SNMP,

Dual configurations, Multiple images, RMON, LLDP/LLDP-MED, sFlow, DHCP/BOOTP Client, IPv4/IPv6, Syslog

server, Debug command, 802.3ah Ethernet Link OAM, 802.1ag Connectivity Fault, Y.1731 OAM, 802.1Ǫbb

Priority- based Flow Control (PFC), Dying Gasp, Cable Diagnostics , 6 kV surge protection on all Gigabit

Ethernet ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must

be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as

Supplying, installation, Testing and commissioning of 10 Giga Bandwidth Data Centre Network Switch of 48

port Layer 3 having features and specifications etc. as mentioned here under: - ToR/EOR/Core Network

Switch 48x 10GbE SFP+, 6x 100GbE QSFP28, RPS, with Console Port, Management Port and 1 x USB 2.0 Type A

port, The switch must provide a switching capacity of no less than 2.16 Tbps and a forwarding rate of at least

1600 Mpps, ensuring non-blocking performance for high-bandwidth applications. It should support hot-

swappable dual power supply modules (AC or DC) for 1+1 redundancy and load sharing, as well as hot-

swappable, front-to-back airflow fan trays with N+1 redundancy to ensure continuous availability. IEEE 802.1X

support for port-based and MAC-based authentication should be available, along with integration for RADIUS

and TACACS+ authentication services. Guest VLANs, DoS prevention, and management access restrictions are

essential. SNMP v1/v2c/v3, syslog, sFlow, and support for autoconfiguration via DHCP. Support for OpenFlow

v1.4, Netconf/YANG, and LLDP is required for modern network automation. Support ONIE (Open Network

Install Environment), IEEE 802.1Q bb Priority-based Flow Control (PFC), OpenFlow v1.4, ERPS, IPv6 Tunneling,

IP interfaces and supported, VXLAN, Private VLAN, Multicast VLAN, Guest VLAN Double VLAN (Q-in-Q),

RoCEv2, PIM-SSM/SM, MSDP. Support High Availability with MLAG/VSS and Layer 2/3 VPNs Critical for Multi-

tenant, Virtualized, and Containerized Environments. BGPv4/v6, OSPFv2/v3, IS-IS, RIPng. VRRP, ECMP, BFD,

and route redistribution for high-availability routing. Support flexible routing domains and secure inter-

segment traffic flow. Certifications: CE, FCC, MTCTE, OEM/Product must be on Trusted Telecom Portal of

Department of Telecommunication, Government of India etc. complete as required.

Supplying, Installation, Testing and commissioning of small form-Pluggable (SFP) for Network Switches. Must

be hot Pluggable, RoHS Complaint, etc. complete as required.

11 39.6.1 1G SFP Single Mode/Multi Mode Each 4 ₹ 4,211.00 ₹ 16,844.00

12 39.6.3 10 G SFP + Single Mode/Multi Mode Each 12 ₹ 14,972.00 ₹ 1,79,664.00

Supplying, Installation, Testing and commissioning of indoor Wireless Access Point for High density use

having features and specifications etc. as mentioned here under- WiFi6 802.11ax 574Mbps (2.4GHz) +

2402Mbps (5GHz), WIFI 6 Certified, 1 x RJ45 console port, MG 2.5G LAN POE Port, factory reset,

WPA/WPA2/WPA3™ Personal/Enterprise, WEP 64/128-bit, SSID broadcast disable, MAC address access

control, Internal RADIUS server, SNMP, Customizable Captive Portal, Auto Channel, Works as Access Point,

WDS, WDS with AP, Wireless Client ., Web (HTTP), Secure Socket Layer (SSL), Traffic control, Support ATF/Fast

Roaming/Band Steering, Supports enhanced security – WPA-PSK/WPA2-PSK/WPA3-PSK and RADIUS client,

and Cipher negotiation, and MAC/ IP ACL for networks, Certifications: MTCTE, CE, FCC. Works as Standalone,

Compatible with S/W & H/W Controller with addtional features like - Real-Time Monitoring and Alerts, Rich

Advanced Features, Centralized Device Management, Role-Based Administration, Real-Time Monitoring, VLAN

and Access Control, Auto RF Management and Bandwidth Optimization, Multi-SSID and Captive Portal

Authentication. OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication,

Government of India etc. complete as required.

Supplying, Installation, Testing and commissioning of indoor Wireless Controller having features and

specifications etc. as mentioned here under- The network controller shall be a dedicated hardware

appliance designed for centralized management of wireless access points, It must support the management

of up to 500 networking devices, The system should be on-premise, ensuring data privacy and complete

control over network configurations. It must include an intuitive user interface for real-time monitoring,

device discovery, firmware upgrades, scheduling, and mass configuration deployment. Features such as role-

based administration, multi-site management. AP to controller communication shall be use of industry

standards-based (IEEE or IETF) CAPWAP or any tunneling protocols as per guidelines of DoT.The controller

should support Layer 2 and Layer 3 device discovery, VLAN configuration, MAC ACL groups, IGMP snooping,

and bandwidth optimization. Automatic radio frequency (RF) management and access policy enforcement are

16 39.10 required for reliable wireless performance. The solution must offer a comprehensive dashboard with network Each 1 ₹ 1,13,228.00 ₹ 1,13,228.00

topology, floor plan views, client and device lists, and alert notifications. For authentication, it should support

a range of methods including local database, external RADIUS, LDAP, and passcode or MAC-based access. It

should provide detailed traffic analytics, logs, and customizable reporting for network visibility and planning.

Firmware and configuration backup and restoration functions must be available, with USB based log storage

supported. Physical specifications should include a compact form factor with a minimum of one 2.5G Ethernet

port and USB 3.0 port, and it must be MTCTE,CE, FCC, and RoHS certified. The controller should operate

reliably within a 0°C to 40°C temperature range and 10–90% non-condensing humidity. /Product must be on

Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded. Must be of 1U height

with clear label holders and white label with the panel. 24 Ports Cat-6 Patch Panel should have TL/UL

verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6 Patch Cord should have ETL/UL

verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.

19 39.12.1 Copper Patch Cords of length 1m (3ft) Each 60 ₹ 151.00 ₹ 9,060.00

20 39.12.2 Copper Patch Cords of length 3m (10ft) Each 10 ₹ 227.00 ₹ 2,270.00

Supplying, Installation, Testing and commissioning of CAT6 Copper Information Outlet (IO) with face plate of

color as per site requirement, should have ETL/UL verification program certificate for compliance with

ANSI/TIA-568.2-D. All copper Cable and Components should be from same OEM to maintain compatibility and

interoperability etc. complete as required.

Supplying, Installation, Testing and commissioning of RJ45 Connector for CAT 6/6A Cables. RJ45 modular plug

26 39.16 supports 4 twisted pairs, 8 positions, 8 connectors. Housing: PC, UL94V-2, transparent color, Use for 24- 26 Each 60 ₹ 6.00 ₹ 360.00

AWG stranded wires etc. complete as required.

Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted Pair Cable in

existing conduit/ on surface, ategory 6 Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL

27 39.17 verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the range ₹ -

of 6.1mm nominal with Operating Temperature Range : -5° to +60°C, Bending Radius : < 4 X Cable Diameter at

–5°C ± 1°C and Pulling Force : 11.5Kg etc. complete as required.

Supplying and drawing following core Multi mode Fiber Optic Cable having corrugated steel armoring, leser

optimize 50/125 µm with HDPE jacket, LSZH (Low smoke Zero Halogen), Tight-buffered or loose tube,

maximum attenuation: < 3.5 dB/km at 850 nm, < 1.5 dB/km at 1300 nm, bandwidth > 2000 MHz-km at 850

nm, > 500 MHz-km at 1300 nm compliance and certifications: ISO/IEC 11801 Ed. 2.2, ANSI/TIA-568-C.3, ITU-T

G.651.1 RoHS compliant. Multi Mode Fiber shall be Central-loose tube filled with Thixotropic jelly, duly

following Standards: ISO 11801, IEC 60793-1/60794-1-2, ITU-T-REC G.652D and Telecordia GR-20-core, High

quality Electro Chromium Coated Corrugated Steel tape (ECCS ) and HDPE- Sheath, Operating ambient

Temperature should be – 5 0C to +50 0C and Storage Temperature should be – 5 0C to +50 0C, Maximum

Attenuation ± 3.5 dB/km at Operational Wavelength 850 nm and ± 1.5 dB / km at Operational Wavelength

1300 nm . type of fiber should be 50/125 / G.652D & Refractive Index should be 1.483/1.478, The value for

Mode-filed,Cladding Diameter 50 ± 2.5 µm and 125 ± 1µm correspondingly i/c splicing & marking etc

complete as required.

38 39.20.1 6 Core Multi Mode Optical Fiber Cable Meter 600 ₹ 87.00 ₹ 52,200.00

39 39.20.2 12 Core Multi Mode Optical Fiber Cable Meter 400 ₹ 109.00 ₹ 43,600.00

Supply and fixing following port Rack Mount loaded LIU with pigtail, Front-mounted cable saddles for jumper

management, suitable to manage both splices and terminations, Pre-assembled shelves in multiple

configurations, Rubber fiber slotted bracket built-in, metal splice shelf to protect the fibers, 2 fiber spools

40 39.21 built-in for 900μm tight buffered fiber storing, Capable of storing up to 3 meters of 900μm tight buffered fiber ₹ -

per adapter, Removable front and rear covers for better access to interior of LIU, Should be Single / Multi

mode LC Type fully loaded. Accessory kit consists of cable ties, mounting ear screws, and spiral wrap tube etc

complete as required.

Supplying and fixing Patch Cord of Optical Fiber Multi Mode or Single Mode LC to LC Fiber Duplex having high

precision ceramic ferrule with good concentricity, Fiber corning single mode G652D, Cable Type 2mm with

Mechanical specification Apex Offset < 50 µm, Fiber Height + 100 nm, End-face radius of Curvature 7mm < R

<25mm, Repeatability < 0.2 db, Working ambient Temperature – 5 0C to +50 0C, Storage Temperature – 10

0C to +50 0C, Length -- 2meter, Type -- LC-LC Duplex etc complete as required.

Supplying and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm CRCA Sheet,

completely knocked-down condition (CKD) Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking, Minimum 2

cable entry/exit provision at Top and bottom with rubber protection, Front 5mm Toughened Glass with lock,

wall mounting kit, Powder coated Color- RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power

distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc.

complete as required.

Supplying and fixing 24U Rack with 4 inch Castor wheels and front brake Floor Standing Rack with Main Frame

Pillar of 1.25mm Powder Coated CRCA Sheet with removable side panels, L- Shape adjustable Vertical

Mounting Rail of 2mm with 'U'Marking completely knocked-down condition (CKD) Shape, fitted with 4

number cooling fans, minimum 5nos two line cable entry/exit provision at top and bottom with rubber

protection, Front door 5mm Toughened Glass with MS frame or MS perforated with lock, Rear MS vented or

perforated door, Powder coated Color- RAL- 7035 or black, complied with UL & RoHS, 2 x 6 sockets 16A

power distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1

number, etc. complete as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess

including cutting the wall and making good the same in case of recessed conduit as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars,

58 15.14 jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as ₹ -

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend,

couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75

cm below ground level) including excavation and refilling the trench but excluding sand cushioning and

protective covering etc., complete as required.

Total (DSR) Amount Rs. ₹ 33,80,057.00

Non Schedule items

Software configration works like VPN and SQL Configration of the POE switch complete in all respect in line

with the existing Campus System

Total (NS) Amount Rs. ₹ 1,20,000.00