ADDN/ALTN AND SPL REPAIRS TO JCOS/OR MD ACCN AT KALIMPONG UNDER GE 867 EWS.

Amount

Dismantling of plain or corrugated steel sheeting, any gauge and thickness including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling of plain or corrugated Asbestos cement, any gauge and thickness including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based steel sheet of approved profile of corrugation, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, eaves board, ridges, hips,valley gutters, drip and straight flashing cladding to wall etc, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

M&L for roughening the surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc including for brushing neat cement slurry @ 3 Kg per square meter complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 25 mm thick plain cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate) as in leveling coarse for tile floor complete all as specified and directed by Engineer-in-Charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick premium quality conforming to IS-13712, grade B-II(a) (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick premium quality conforming to IS-13712, grade B-II(a) (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surfaces such as dado/skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing rubbish off the complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick premium quality conforming to relevant IS (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

M&L 300 x 200 x 7 mm thick coloured glazed ceramic tiles fixed as in vertical surface such as risers of steps, skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 15 mm thick rendering in CM 1:4 finished even and rough complete all as specified and directed.

M&L for machine cut Kota stone slab flooring, 17-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing and exposed edges of Kota stone shall be rounded complete over and including 20 mm thick screed bed or bedding layer in CM 1:6 finished even and rough all as specified and directed.

M&L for machine cut Kota stone slab as in vertical surfaces such as dado/skirting, 17-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing and exposed edges of Kota stone shall be rounded complete over and including 10 mm thick rendering in CM 1:4 finished even and rough all as specified and directed.

M&L 17 - 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete over and including 20 mm thick screed bed or bedding layer in CM 1:6 finished even and rough all as specified and directed.

M&L for 50 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection/path laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M/L for 10mm thick rendering in CM 1:3 on other than fair faces of brick or concrete surfaces of internal walls in sunken slab finished even and fair with WPC.(WPC measured separately).

M&L for first layer of slurry of cement at the rate of 0.488Kg/Sqm mixed with acrylic based polymer modified cementitous composite compound at the rate of 0.253kg/Sqm this layer will be allowed to air cure for 4 hours,second layer of slurry of cement at the rate 0.242 kg/Sqm mixed with acrylic based polymer modified cementitous composite compound at the rate of 0.126 kg/Sqm.this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours including 200 micron thick polythene film pasted with the help of adhesives shall be provided over above treatment.NOTE:The rate includes preparation of surface,treatment and sealing of all joints,corners,junctions of pipes and masonary within polymer mixed slurry.This treatment shall be provided after provision of pipes and masonary within polymer mixed slurry.This treatment shall be provided after provision of cement plaster mixed with WPC and synthetic fibers while concrete is still green complete all as specified and directed by Eng-In-Charge.Make: STP/Dr Fixit sunken treatment/psdilite eqavalent.

M&L for PCC (1:5:10), type E2, using 40mm graded stone aggregates as in foundations, filling and mass concrete complete all as specified and directed

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels, drains including all necessary form work complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including cutting of reinforcement as required to facilliate demolition complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type A1 1:1½:3 (20mm graded crushed stone aggregate) as in Chajjas and the like complete all as specified and directed.

Use & Waste of formwork to Chajjas, chullah hoods, troughs and similar items including edges rough finished surfaces complete all as specified and directed.

S&F of TMT bars 10 mm dia and over, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

S&F of TMT bars 6 mm to 8 mm dia, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Taking down cement plaster on brick or stone masonry surfaces of walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, rendering finished even and smooth (without using extra cement) complete complete all as specified and directed.

M&L 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:4 on external wall finished even and fair mixed with integral water proofing compound @ 3% by weight of cement or in the manner specified by the manufacturer and in the proportions indicated all as specified and as directed. Note:-WPC will be measured and paid separately as supply only.

Supply only integral water proofing compond all as specified and as directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as on ceiling and finished fair and even without using extra cement complete all as specified and directed.

M&L for two coats of old bound distemper over a coat of priming coat on newly prepared wall surfaces, including 3 mm thick layer of wall care putty (Birla white or equivalent) all as specified and directed..

M&L scrapping of existing treatment and applying two coats of thin layer of wall care putty (Birla white or equivalent) and then applying two coats of oil bound distemper over a coat of priming coat after preparation of wall surfaces complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash on walls complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of wall and applying one coat of white wash as in wall complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash as in ceiling complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash as in ceiling complete all as specified and directed.

Material & Labour for prepration of new wall plastered surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over a 3mm thick wall care putty and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surface complete all as specified and directed.

Material & Labour for completely removal of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over a 3mm wall care putty and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surface complete all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position (framed work) all as specified and directed.

Dismantling timber fillets, rails, posts rafters purlins etc under 40 Sqcm in section fixed in any position complete all as specified and directed.

S&F GI frame work of size 605 x 605 mm, for seamless celing comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed.

S&F PVC False ceiling with light weight PVC hollow section pannel made of 1 mm thick and over all thickness of panel 7mm thick and 200 mm wide strips of colour - teak/wood grain/Melamine finish, fixed in new false ceiling grid made of Aluminum/G.I/M.S/wood complete all as specified and as directed. Note:- New false ceiling grid of aluminium/GI/MS/wooden if provided shall be measured and paid separately.

S&F of joist, channel, angle, flat iron or Tee sections, fixed independently with connecting plates, etc confirming to Fe 410-W (Gde 250 quality A) complete all as specified and directed.

Demolition of brick work or stone/boulder masonary, built in lime mortar including all quions, arches, pillars etc, but excluding ashler facings, dressed stone work and precast concrete articles.

M&L for brick work with sub class 'B' bricks , using old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in same opening after Resecuring or easing & adjusting complete all as specified.

Taking down chowkhats or frame not exc 1.50 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frame exc 1.50 and not exc 4 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered , put together with glue, pinned at joints complete all as specified and directed.

S&F pressed steel frame of size 125 x 60mm for door with one or more rebates including necessary fixing, lugs, hinges,lock ,strike plate, etc complete all as specified.

S&F pressed steel frame of size 105 x 60mm for door with one or more rebates including necessary fixing, lugs, hinges,lock ,strike plate, etc complete all as specified.

S&F 35 mm thick (batten thickness) second class hard wood , plain, framed panelled shutters (any number of panels), with panels of 12 mm thick timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density wood particle board with commercial face veneers complete all as specified and directed. (Note :- The dimension of the various components or parts of shutters shall be as specified in clause 8.24 (a) of MES SSR 2009 Part I)

S&F 35 mm thick (batten thickness) second class hard wood, glazed and Skelton shutters, open rebated and prepared to receive glass, gauge, etc , divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded with cut mitred beds for securing glass etc, supplied and fitted to chowkhats complete all as specified and directed. (Note :- The dimension of the various components or parts of shutters shall be as specified in clause 8.24 (a) of MES SSR 2009 Part I)

S&F of solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube as per specification and drawing given in clause 8.B.3 of SSR -2010 (Part-II Rates) complete all as specified and directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing given in clause 8.B.2 of SSR -2010 (Part-II Rates) complete all as specified and directed.

S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete complete all as specified and directed.

S&F steel window or ventilator fixed type with glazing bar complete complete all as specified and directed.

M&L for 19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work fixed in repair complete all as specified and directed.

M&L for external teak wood lipping, 6mm thick fixed with nails for 19 mm thick Prelaminated particle board

M&L for 12 mm thick block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work including exposed surfaces finished with external teak wood lipping, 6 mm thick fixed with nails fixed in repair complete all as specified and directed.

M&L for external teak wood lipping, 6mm thick fixed with nails for 12 mm thick block boards.

S&F of small fittings such as brackets of any type latch and hinge block, shaped door window stops and the like in second class hard wood article not exc 200 cucm each complete all as specified and directed.

S&F 50 mm size butt hinges, medium weight , cold rolled, mild steel complete all as specified and directed

M&L for IInd class hard wood plain fillets.area exc.3 and exc. 6 Sqcm square, rectangular or triangular in section, clean sawn, secured with nails or bradsbut bullnosed, splayed, chamfered or rounded on one edge or face

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in bed blocks for grouting hold fasts , coping, filling in pressed steel chowkat or similar work including necessary form work as required complete all as specified and directed.

S&F mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars,barred iron doors, ladders, framed balusters, walk ways, railings and similar work confirming to Fe-410-0 or Fe 310-0 complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight , stainless steel complete all as specified and directed

S&F 100 mm size butt hinges, medium weight , cold rolled, mild steel and fixed in repair complete all as specified and directed

S&F of continuous (piano) hinges mild steel bright finish or electro galvanised 30 mm width of flaps complete all as specified and directed.

S&F of 150 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed all as specified and directed.

S&F of 150 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed in repair complete all as specified and directed.

S&F of 200 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed all as specified and directed.

S&F of 200 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed in repair complete all as specified and directed.

S&F 125 mm size Aluminium handles, cast type, anodised and all as specified and directed.

S&F 150 mm size Aluminium handles, cast type, anodised and all as specified and directed.

S&F 150 mm size Aluminium handles, cast type, anodised and fixed in repair complete all as specified and directed.

S&F of 300 mm long aluminium alloy, anodised sliding door bolts with haps staple(bolt type), and fixing clips of sheet, cast or extruted sections and fixing bolt and sliding bolts of extruted sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F of 300 mm long aluminium alloy, anodised sliding door bolts with haps staple(bolt type), and fixing clips of sheet, cast or extruted sections and fixing bolt and sliding bolts of extruted sections or cast aluminium alloy and fixed in repair complete all as specified and directed.

S&F of 100 mm size haps and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&FStainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&FStainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples fixed in repair complete all as specified and directed.

S&F in repairs decorative type drapery curtain rod (curtain rails), of 25 mm dia powder coated with fixing brackets, stops, rollers etc complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane complete all as specified and directed.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty in square not exc 0.50 sqm in each pane complete all as specified and directed.

M&L preparation of new wooden surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of old wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L preparation of old steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F of PVC low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet, ball valve, float valve, bends brackets, rawl plug, brass screws handle etc complete having BIS description mark with IS-2731 with and including suitable size of MS brackets, plug, screw all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc, and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with water closet of any type all as specified and directed.

S&F in repairs water closet (squatt pattern) of vitreous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe anti syphonic pipe etc complete including P or S trap set in and including necessary lean cement concrete complete all as specified and directed.

S&F in repairs vitreous china wash basin white of any pattern, flat back of size 550mmx400mm (excluding taps), waste, chain and plug including waste pipe ,suitable size of brackets and making good the damaged walls as per existing wall finish complete all as specified and directed

S & F pillar tap Fancy Type cast copper alloy 15mm bore with capstan head, chromium plated, screwed down high pressure, with or with out lettered "Hot" or "Cold" with long screw shank and fly nuts, screwed for iron pipes.

S&F in repairs of 1mm thick stainless steel sink with drainage board kitchen or laboratory type with waste pipe, plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F 40mm waste coupling of CP (half or full threaded) . (Minimum weight 60 gms)

S&F in repair Brass chromium plated shower rose with or without swivel joints 125 mm size , including fixing to steel pipe or unioncomplete all as specified and directed.

S&F in repair 15 mm bore PVC connection 450 mm long with two brass chromium plated brass nuts and PVC washers complete all as specified and directed.

S&F in repairs angle, stop valve 15 mm bore, chromium plated, fancy type, with wall flange, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Taking up or down 15 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

S&F of 15 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed,

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth on stone walls complete all as specified and directed.

S&F in repair 15 mm bore chromium plated bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs grating doom 100mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

S&F in repairs kitchen plate rack made out of stainless steel 0.50 mm thick sheet with partitions and size of rack 800 x 250 x900 mm with shape and pattern as per sample kept in Sample room of GE Office complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail of 20mm dia D' type 60cm long between flanges complete all as specified and directed.

S&F in repairs 75 mm size PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S & F SWG gully trap size 150 x 150 mm square or round mounted type ‘S’, setting and jointed with solvent cement complete all as specified.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs Soap dish, CP, fixed to plugs with chromium plated brass screws complete all as specified and directed

Demolition and breaking up old broken , PVC (SWR) , Cast Iron, AC, SWG soil waste and vent pipe of 75/100/110 mm bore including accessories set in cement mortar and removing rubbish from site as directed by Engineer-in-Charge complete all as specified and directed.

S&F of 110 mm PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F of 75 mm PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) junction single (Single T) equal or unequal with access door jointing with solvent cement complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) junction single (Single T) equal or unequal with access door jointing with solvent cement complete all as specified and directed.

S&F of 110 X 75 mm bore PVC (SWR) reducer including jointing with solvent cement complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified and directed.

M&L for coloured & polished Chequered cement concrete tiles 30cm x 30cm x 25mm thick,set, jointed and pointed in neat cement slurry as in floors includig 20mm thick screed bed CM(1:6) all as specified and directed.

Taking down copper/aluminium point wiring (light fan, Socket or power ) Complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, light fitting etc, removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors, etc. as directed by the Engineer – in - Charge.

Disconnection and taking down distribution boards, switch fuse unit, , enclosure for MCB including MCB's of any type and size and keeping aside for reuse of serviceable one.

Material and labour for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core multi stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC casing and capping not less than 20mm size, medium grade with all necessary fittings, surface wiring , for light / E/fan/Bell point controlled by one switch including 1.5 Sq mm PVC insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes (concealed type in permanent bldg and surface in temporary bldg or as directed ) for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover ,for housing switches, socket outlet, regulator etc. complete all as specified or directed including testing on completion.

All as per item No132 here – in – before but for one 3 / 5 -pin switch socket outlet 5 amps on independent board.

All as per item No 132 here-in-before but One 3 pin socket outlet 5 Amps on the same board with other switchs with cables 1.5 Sqmm size.

All as per item No 132 here – in – before but for one switch socket outlet 15 Amps on independent board with 2.5 Sqmm multi stranded and 2.5 Sq mm stranded (for earth) PVC insulated un-sheathed copper cable.

Supply and fix switch piano flush button, single pole, 5 amps, one way all as specified and as directed.

Supply & Fixing Bell, AC 230 Volts single pole including mounting block all as specified and as directed.

Supply & fixing Bell push flush type, 5 Amps button complete all as specified and directed..

Supply & Fixing ceiling rose surface bakelite 65 X 50 mm three terminal all as specified and as directed.

Supply and fix switch socket combination 2 – in – one, 3 Pin / 5 Pin, 5 amps flush type all as specified and as directed.

Supply and fixing switch socket combination 2 – in – one 6 Pin , 5 / 15 amps flush type universal all as specified and as directed.

S & F Energy efficient LED tube light fitting not less than 4", not less than 1x22 watt, with bipin holders, connector block, CCT - 6500K, system output lumen not less than 2000lm, extruded aluminium housing with high quality Polycabonate diffuser, wide voltage protection range 140V-270V including connecting up with PVC insulated 3 core sheathed 0.5 sqmm copper conductor two numbers PVC mounting blocks for fixing of fitting complete all as specified and as directed.(Make : Philips, Model - TMC 501, TMC 501P 1XT-LED 22W P3241 or equivalent make of Havells/M/s Simoco Telecommunications (South Asia) Ltd/ M/S Jaquar & Company Pvt Ltd / M/s HPL Electric & Power Ltd /M/S Eveready Industries India Ltd / M/S Crompton Greaves Consumer Electricals Ltd/ M/S Halonix Technologies Pvt Ltd / M/S Century LED Ltd (Brand MAGIK) /M/S C&S Electric /M/s Panasonic Life Solutions India Pvt Ltd (Brand: Panasonic)/ M/s Dhanashree Electronics Ltd (Brand: RASHMI) / M/s SORIL Infra Resources Limited/ M/s Syska LED Lights / M/s Surya Roshni Limited (External / Internal)/ M/s Orient Electric Limited (a CK Birla Group Company)

Supply, Fixing, Testing & Commsioning of IP66 & IK09 integral LED Bulk Head luminaire with housing made of Pressure Die Cast alumunium & Optical cover made of Opal Polycarbonate for glare free lighting . System Lumen Output of minimum 600 lumens. Power Consumption should not exceed 10W (Including Driver Loss). For Glare free lighting luminaire should be with Opal diffused Polycarbonate complete all as specified and as directed. Make : Philips, Cat part No. WT 202W LED 6S CW PSU S2 PC or equivalent make of M/s Simoco Telecommunications (South Asia) Ltd/ M/S Jaquar & Company Pvt Ltd / M/s HPL Electric & Power Ltd /M/S Eveready Industries India Ltd / M/S Crompton Greaves Consumer Electricals Ltd/ M/S Halonix Technologies Pvt Ltd / M/S Century LED Ltd (Brand MAGIK) /M/S C&S Electric /M/s Panasonic Life Solutions India Pvt Ltd (Brand: Panasonic)/ M/s Dhanashree Electronics Ltd (Brand: RASHMI) / M/s SORIL Infra Resources Limited/ M/s Syska LED Lights / M/s Surya Roshni Limited (External / Internal)/ M/s Orient Electric Limited (a CK Birla Group Company)

Supply and fixing wall mounted LED luminare, not less than 1x 10 watts with glass shed, prewired with holder, including one 10 watts LED lamp, complete all as specified and as directed.Make :Havells City 3 Cat No .LHDL0616099 or equivalent make of Philips/Bajaj/ M/s Simoco Telecommunications (South Asia) Ltd/ M/S Jaquar & Company Pvt Ltd / M/s HPL Electric & Power Ltd /M/S Eveready Industries India Ltd / M/S Crompton Greaves Consumer Electricals Ltd/ M/S Halonix Technologies Pvt Ltd / M/S Century LED Ltd (Brand MAGIK) /M/S C&S Electric /M/s Panasonic Life Solutions India Pvt Ltd (Brand: Panasonic)/ M/s Dhanashree Electronics Ltd (Brand: RASHMI) / M/s SORIL Infra Resources Limited/ M/s Syska LED Lights / M/s Surya Roshni Limited (External / Internal)/ M/s Orient Electric Limited (a CK Birla Group Company)

Supply and fixing lamp holder insulated body with back plate for batten fitting all as specified and as directed.

S & F in LED retro fit lamp B-22 holder base with poly carbonate body and aluminium heat shrink of 5 W complete with tube rod all as directed.

Supply and fixing Sheet metal enclosure for MCB TPN DB’s, Phosphatised Powder Painted Double door 200 amp rated, Triple pole and neutral link of 4 way 415 volt AC including provision of MCCB, 4 Pole, 63 Amp, 16 KA complete all all as specified and directed.Make- M/s C&S Electric Ltd/M/s Novateur Electrical & Digital Systems (Optipro) /Legrand/Siemens/Schneider.

Supply and fix MCCB, Tripple Pole & Neutral, 63 Amps, 415 volts, 50 Hz, 16kA complete all as specified and directed. Make- M/s Larsen & Toubro Ltd/M/s Havells India Ltd MCB (Brand-Max3, EURO-II), MCCB (Brand- HIM & HIX)/M/s Panasonic Life Solutions India Pvt Ltd (Switch Gear: Panasonic)

Supply and fixing Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 200 Amps rated Single pole and neutral linkof 8 way 240 Volts AC complete all all as specified and directed.Make- M/s C&S Electric Ltd/M/s Novateur Electrical & Digital Systems (Optipro) /Legrand/Siemens/Schneider.

Supply and fixing MCB Single pole and neutral upto 40 Amps capacity 10 KA 240 Volts 50 HZ. conforming to IS/IEC 60898-1 2002, integrated label holder, Sliding bottom clamp,suitable protection complete all as specified and directed . Make- M/s Larsen & Toubro Ltd/M/s Havells India Ltd MCB (Brand-Max3, EURO-II), MCCB (Brand- HIM & HIX)/M/s Panasonic Life Solutions India Pvt Ltd (Switch Gear: Panasonic) /Legrand/Siemens/Schneider.

Supply and fix MCB/Isolator single pole (SP), 10 kA of 6 Amps to 32 Amps capacity 240 Volts. conforming to IS/IEC 60898-1 2002, integrated label holder, Sliding bottom clamp,suitable protection complete all as specified and directed . Make- M/s Larsen & Toubro Ltd/M/s Havells India Ltd MCB (Brand-Max3, EURO-II), MCCB (Brand- HIM & HIX)/M/s Panasonic Life Solutions India Pvt Ltd (Switch Gear: Panasonic) /Legrand/Siemens/Schneider.

M&L for sub main wiring along with earth wire of size two run of 6 sq mm + one run of 6 Sq mm earth wire single core PVC insulated FRLS cable with stranded copper conductor FRLS including drawing into 25 mm rigid non-metalic PVC conduit concealed in wall.(Note Two run of 6 Sqmm and one run of 6 Sqmm wire including one run of 25 mm dia cunduite shall be measured as one unit length including taking down of old servicible sub main wiring.

Taking down KWH and keep in safe custody and refixing the same as including necessary electric connection from main to KWH meter and KWH meter to out going distribution board.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating lement upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc including necessary electric/water connection grouting of MS fastener of suitable size complete all as specified and directed .

S&F metal plug socket single pole and neutral encloser with two pin earth plug with 01 No MCB SP 20 Amp, C series complete all as specified.

M&L for making hole in the existing wall/building without distrubing to existing infrastructure for fixing of exhaust fan complete including making good to match with the existing specification complete all as directed .

Supply and Fixing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed. Make : M/s Havells India Ltd/Crompton/Usha/Havells/Bajaj/Orient.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m bellow normal ground level, connected to galvanized earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI med grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC 1 : 3 : 6 type C-1 , 50 mm thick pre cast RCC 1 : 2 : 4 type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar ,GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 5 of MES SSR Part-I and as directed.

S&F LED security light suitable for 35 W LED with pressure di cast housing with epoxy power coated drak graphite grey colour finish , Prismatic ploycarbonate cover with individual LED lenses, IP65 by using 25mm dai GI bracked fixed on wall by means of nuts, botls and clamps. Make : M/s Simoco Telecommunications (South Asia) Ltd/ M/S Jaquar & Company Pvt Ltd / M/s HPL Electric & Power Ltd /M/S Eveready Industries India Ltd / M/S Crompton Greaves Consumer Electricals Ltd/ M/S Halonix Technologies Pvt Ltd / M/S Century LED Ltd (Brand MAGIK) /M/S C&S Electric /M/s Panasonic Life Solutions India Pvt Ltd (Brand: Panasonic)/ M/s Dhanashree Electronics Ltd (Brand: RASHMI) / M/s SORIL Infra Resources Limited/ M/s Syska LED Lights / M/s Surya Roshni Limited (External / Internal)/ M/s Orient Electric Limited (a CK Birla Group Company)/Philips/Wipro/Bajaj/Havells.

M&L in repairs for sub main wiring along with earth wire of size two run of 4 sq mm + one run of 4 Sq mm earth wire single core PVC insulated cable with stranded copper conductor FRLS including drawing into 25 mm rigid non-metalic PVC casing caping on wall.(Note Three run of 4 Sqmm including one run of 25 mm dia conduite shall be measured as one unit length including taking down of old servicible sub main wiring.

Note 1:- (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/ amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected.

JAYSHREE CONCERN

MS MAYA PRAKASH GOEL AND SONS

C. M. AGARWAL AND CO

DEEP CHANDRA JOSHI

MANOJ JINDAL

S K ENTERPRISES

GEETA CONSTRUCTION