Fabrication assembly in situ G-3/L type glued insulated joints for broad gauge 60 Kg/52 Kg with all contractor's materials, to and from transportation of material, octroi etc. Complete as per instructions contained in manual for glued insulated rail joints in the section of Khalilabad - Bansi in connection with Khalilabad - Bahraich new line project of Lucknow Division of N.E. Railway.

Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or "V" whichever is less, where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-2 of Chapter-3, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. 10.3 Bid Capacity: The tender/technical bid will be evaluated based on bid capacity formula detailed in Annexure-3 of Chapter-3. The statement of existing commitments and balance amount of ongoing works should be submitted as per Annexure-E attached with tender document. 10.4 No Technical and Financial credentials are required for tenders having value up to Rs 50 lakh. 10.5 Credentials if submitted in foreign currency shall be converted into Indian currency i.e., Indian Rupee as under: The conversion rate of US Dollars into Rupees shall be the daily representative exchange rates published by the Reserve Bank of India or entity authorized by RBI to do so for the relevant date or immediately previous date for which rates have been published. Where, relevant date shall be as on the last day of month previous to the one in which tender is invited. In case of any other currency, the same shall first be converted to US Dollars as on the last day of month previous to the one in which tender is invited, and the amount so derived in US Dollars shall be converted into Rupees at the aforesaid rate. The conversion rate of such currencies shall be the daily representative exchange rates published by the International Monetary Fund for the relevant date or immediately previous date for which rates have been published.

Tenderers who fulfil requisite eligibility criteria mentioned in forgoing Para shall participate the tender. Details as per Annexure-1 of Capter-3 is required to be submitted. Only RDSO approved firm participate in this tender. 10.0Eligibility Criteria: 10.1Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of the tender. In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b (1): Separate completed works of minimum required values shall also be considered for due fulfilment of technical eligibility criteria for different components. (b)(2) In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b)(3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contract of or through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfil technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract.

Similar nature of work means: - "Fabrication and laying of in situ Glued Joints of RDSO approved design and drawing in Railway projects."

In addition to above, documents listed below are also required to be submitted with the offer:- (i)History Sheet of tenderer as per proforma given in Annexure -A (ii)Details of construction machineries, tools and plants, vehicle etc. available on hand and proposed to be utilised in work as per Proforma given in Annexure-B. (iii)Details of technical and other personnels available on hand and proposed to be engaged as per Proforma given in Annexure-C (iv) Details of works completed during previous seven financial years and current year by the tenderer (s) as per Proforma given in Annexure-D. (v) Details of works in hand/progress of the tenderer(s) as per Proforma given in Annexure-E. (vi)Declaration regarding association of railway officer(s) with tenderer(s) as per Proforma given in Annexure-F (vii) List of court cases during previous three years as per Proforma given in Annexure-G. (viii) List of arbitration cases during previous three years as per Proforma given in Annexure- H. (ix)Broad plan of execution of this work within the stipulated completion period as per Proforma given in Annexure-I. (x) Other credentials/facilities of the firm/contractor in Annexure-J. (xi) Declaration regarding visiting site of the work Proforma as given in Annexure-K (xii) Constitution of Firm, Proforma as given in Annexure-L. (xiii)Details of Real Time Gross Saving (RTGS)/National Electronic Fund Transfer (NEFT) Proforma as given in Annexure-M.

Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.