SPL REPAIR TO BLDG NO T-26 (SR/BLDG-06/22-23), SPL REPAIR TO BLDG NO T-34 (SR/BLDG-07/22-23) AND PRON OF OVERHEAD PROTECTION SHED (MINOR-16/22-23) AT ASC BN SA UNDER GE JORHAT.

Amount

NOTES :The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Excavation in post holes not exceeding 0.5 cum and getting out and returning filling in, ramming earth in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good in hard/dense soil.

Material and labour for Plain Cement Concrete M-10(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

Reinforced Cement Concrete M-20 (Nominal mix) using 20 mm graded stone aggregate as in beams and Lintel Beam complete all as specified and directed.

Reinforced Cement Concrete M-20 (Nominal mix) using 20 mm graded stone aggregate as in chajja complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves for flat surfaces

Use and waste of formwork to chajjas and similar items including edges.

Material and labour for TMT Bars Fe 500D over and icluding 10mm dia cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Material and labour for High strength steel TMT bars Fe 500D of 6 mm dia and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia

Dismantling plain/corrugated steel sheeting, any guage, thickness including eves gutter / rain water pipe complete & removal all as specified

Dismantling steel work including gates, rafter, purlin, roof truss etc complete all as specified & as directed.

Dismantling timber scantling 40 Sqcm and over in section, in any position (Unframed work) complete all as specified and as directed.

Material and labour for mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality- A incl welding, nuts and bolts complete all as specified and directed.

Material, labour and fixed Rolled mild hollow steel sections steel of grade YSt 310 conform to IS 4923-1997 in roof trusses (framed), trussed, purlins, bracing and fastenings including distance pieces, cleats etc.complete all as specified and as directed. Note:- The steel trusses shall be provide as per TD no CESZ/STD/26.

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material and labour for mild steel screw bolts (machine made) with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 22.5 cm and not exceeding 30 cm long, dia of neck 16 to 20 mm complete all as specified and as directed

Material & labour of Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W (Gde- E- 250) quality- A complete all as specified and as directed

Material and labour for GI Frame work for seamless ceiling comprising of GI perimeter channel 0.55mmm thick with two unequal flanges of 20 and 30mm and web of 7 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended form soffit at approx 900mm centre to entre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre, sutiable type GI wire hanging arrangement with adjuster all as specified in in SSR part-II page no 184to 186 and including 4mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer and including taking down existing false ceiling complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing

Material and labour for old Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for old brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Material and labour for Precast cement concrete block masonry with Precast PCC 1:3:6 type C1 solid blocks, 10 cm thick (with plain or interlocking joints as directed), setting in CM 1:6, complete, in walls.complete all as specified and as directed.

Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Supply only integral liquid water proofing compound complete all as specified and directed.

Material and labour for Preparation of new surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for preparation of new surfaces and and applying 2 coats of cement based paint over a coat of alkali based primer complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors, sunken floor and paving complete all as specified

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for75 mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Plain Cement Concrete M-15(Nominal Mix) using 12.5 mm graded stone aggregate as in making good window opening, lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

Material & Labour of vitrified ceramic tiles,double charged dark coloured shade, 10 mm thick of square/rectangular area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 15mm thick screed bed layer in CM (1:4)complete all as specified and as directed.

All as per item No __ here-in-before but to vertical surfaces such as skirting over and including 10mm thick rendering in CM (1:3) complete

Material & Labour Material and labour for outdoor, antiskid, vitrified paving tiles, of size 300mmx300mmx10mm laid in floors, set and jointed in cement mixed with pigment to match tile colour over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. not exceeding 1.50 Sqm each complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B-1 using 20mm graded crushed aggregate as in filling in holdfast/ filling in pressed steel frame etc including necessary form work complete all as specified and directed.

Supply and fixing of Solid PVC Double door frame of size 50mm x 95mm made out of 5mm wood grain printed colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

Supply and fixing of Factory made solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles), 2,4, or 6 raised panel design with 2 mm thick Moulded prelam PVC sheet on the front face and 2 mm plain colour prelam PVC sheet on back face with particle board core.

Supply and fixing Factory made solid panel wire guage PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling wii be wire guage. The wire guage shall be wrappedon an additional square 8 mm MS solid tube.This tube shall be welded to MS tube. The wire guage shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing

Supply and fixing of steel windows with side hung shutters including hinges projecting type with steel handle and steel peg stay complete with gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of steel windows with side hung shutters including hinges box type with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing in repairs of sheet glass 4 mm thick ordinary quality fixed to aluminum door & window in squares in each pane of required size complete all as specified and as directed.

Material and labour for Stainless steel wire cloth, 0.43 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Material and labour for Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Material and labour for Aluminum handles type anodised 150mm size complete all as specified and as directed

Material and labour for Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Material and labour for Floor door stopper of SS body and tongue, anodised, with hard drawn steel spring of size 150 mm, fixed in floor complete all as specified and directed.

Supply and fixing of end finials for drapery rod and including closed type stainless steel all brackets fixed on wall complete all as specified and directed.

Supply and fixing in repairs Stainless Steel drapery road (1 mm thick stainless steel section outer dia 25 mm with bracket, ring & fancy side holders complete all as directed by Engr-in-Charge

Material and labour for preparation of new steel surface and applying Painting 1 coat of black bituminous paint on steel and iron surfaces of any description over 10 cm in width or girth including preparation and one coat of red oxide primer complete all as specified and as directed..

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR E/M PORTION (Sl No __ to ____)

Taking down carefully unserviceable copper / aluminium point wiring (light, fan, bell socket or power) including all fittings such as switches, socket, ceiling roses , regulators and switch boxes etc complete and making good the disturbed surfaces complete all as specified and as directed.

Material and labour for concealed point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing complete switch for One light/fan/bell point controlled by one way switch. Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

All as per item no60here-in-above but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item no 60 here-in-above but above but for one 5 amp socket independent complete all as specified and as directed.

Material and labour for concealed point wiring complete with 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing 3 pin socket outlet 15 Amp independent:- Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

Supply and fixing of switch piano flush single pole one way 5 amps complete all as specified and as directed.

Supply and fixing switch socket outlet multipurpose 3 pin 15 Amps /5 Amps controlled by one switch.

Supply and fixing switch socket outlet multipurpose 3 pin 5 Amps /5 Amps controlled by one switch.

Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed.

Material and labour for point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for one light/fan point controlled by one switch complete all as specified and as directed.

Material and labour for Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 6 amps on independent board complete all as specified and as directed.

Material and labour for Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSH copper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly for one 5 amps socket outlet on same board with other switch complete all as specified and as directed.

Materials and Labour for Point wiring with 4.00 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 4.0 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 16 amps on independent board complete all as specified and as directed. NOTES FOR ITEM NO 68 to 71:- Flush steel terminal box, inner plate and front plates shall be measured and paid seperately. Cutting chases and making good in walls shall be deemed to be included in the unit rate.

Material and labour for Metal flush box 2 modular complete all as specified and as directed.

Material and labour for Metal flush box 3 modular complete all as specified and as directed.

Material and labour for Metal flush box 8 modular complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 2 modular complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 3 modular complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 8 modular complete all as specified and as directed.

Material and labour for Modular switch 6 Amp single pole one way complete all as specified and as directed.

Material and labour for Modular switch 16 Amp single pole one way complete all as specified and as directed.

Material and labour for Modular socket 16/6 Amp 3 pin combined shattered complete all as specified and as directed.

Material and labour for Modular socket 6 Amp 2/3 pin combined shattered complete all as specified and as directed.

Material and labour for Modular Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed.

Material and labour for Blanking plate SP with incoming contact complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 20Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 120 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No CCS-100-20-65-HL2-DP-NWH of Crompton/ BCLAB 20W WH LED P of Bajaj or equivalent model of make list as given in PS as approved by GE.

Supply & Fixing of LED street light fitting ( Building Security light) of 35Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with 110 Lumen per watt and electronic driver with efficiency > 85% . The light fitting shall be fixed on wall/pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer and including taking up old light fitting complete all as specified and as directed Make:- Model No- TRP-400-35-57-SL-LM-NSR of Crompton Greave/ NXT P 36L WH CR PC SD of Bajaj or equivalent model of make list as given in PS. Notes : GI pipe bracket and clamps shall be deem to be included above quoted rate..

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and necessary connecting PVC insulated Flexible cable for connection from ceiling rose to fan and connecting complete all as specified.

Supply and Fixing exhust fan 240V, 300mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium lowers and shutters fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 4 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.

Supply and fixing in repair of sheet metal enclosure for MCBs to be used triple pole & nutral double door 6Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.

Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.

Supply and fixing MCB DP 40 to 63 amps 240 volts 10KA breaking capacity.

Supply and fixing MCB FP 40 to 63 amps 415 volts 10KA breaking capacity.

Supply and fixing of sub main wiring with two single core 6.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 6.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Supply and fixing of sub main wiring with two single core 4.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 4.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts check nuts and washers of galvanised iron using GI 4 mm dia wire as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 40mm dia GI medium grade earth lead protection pipe, CI frame and cover, wire, copper lugs etc mesh, chorcoal and common salt in alternatee layer complete all as specified and directed .

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.