CLEANING AND REPAIR SEWAGE LINE SEPTIC TANK MANHOLES IN AKASH AND MARU VIHAR AT AF STN SURATGARH

Amount

BOQ (CLEANING AND REPAIR OF SEWAGE LINE, SEPTIC TANKAND MANHOLES IN AKASH & MARU VIHAR AT AF STN SURATGARH )

Cleaning of all blockages of Nahni traps/floor traps/bottle traps, blockages of WC's, 100 mm dia CI pipe upto 1st manhole/GT in shafts, vertical CI soil/waste pipe stacks, CI Tee/door bends etc to maintain sewage system by employing Safaiwala from 0900 hours to 1700 hours with permissible lunch break at Akash Vihar, OMQ and Maru Vihar,officers mess on daily basis with manual/pressure cleaning pump and flexible rods and other necessary mechanical equipments all as directed by Engr-in-Charge. Note : (i) Supervisors should received everyday complaint through MES Complaint register for Akash Vihar (SMQ, OMQ ) and Maru vihar. (ii) Penalty in case not attending to each complaint during same working day will be recovered from contractor @ Rs.100 per complaint. (iii) Rate included for all necessary T&P for Mechanical cleaning / manual cleaning shall be provided by Contractor. (iv) The Disposal of mud/silt, sludge & other debris retreived from cleaning time should remove outside of MOD premises complete all as specified and directed by Engr-in-Charge (v) If necessitated by JE/Engr-in-Charge/ GE, contractor will provide to attend the complaints as required on Sunday/ holidays.

Cleaning of pipe drains by rodding 150 mm internal dia of drain pipe upto 3.0 mtr in depth and removal of sludge/silt/liquid mud sand (in foul conditions) etc out of MOD premises including testing of drains by filling the pipe with water, complete all as specified and directed by Engr-in-Charge (Depth to be measured from existing level to invert level of pipe) complete all as directed and specified by Engr-in-Charge.

All as per item No 2 above but cleaning of 200 mm internal dia of drain pipe depth upto 3.5 metre complete all as directed and specified by Engr-in-Charge.

Dewatering/desilting manholes of any size, upto 1.50 metre depth and removing all solid/semi solid waste matter or silt residue both organic and inorganic in nature (by manual or mechanical system at contractor’s discretion) including removing RCC manholes covers and refixing the same after making the manhole fully functional, complete all as specified and directed by the Engineer-in-Charge. Note:- Rate included for Removing of all solid/semi solid waste material out side to MOD land during same day of cleaning.

Dewatering/desilting manholes of any size, depth exc 1.50 metre and not exc 5 metre and removing all solid/semi solid waste matter or silt residue both organic and inorganic in nature (by manual or mechanical system at contractor’s discretion) including removing RCC manholes covers and refixing the same after making the manhole fully functional, complete all as specified and directed by the Engineer-in-Charge. Note:- Rate included for Removing of all solid/semi solid waste material out side to MOD land during same day of cleaning.

Cleaning of Grease trap tank by taking out the sludge mud/silt etc and removing to outside of MOD premises complete all as specified and directed by Engr-in-Charge

Removing all deposited Clay/slit/muds/Cobbels/solid or semisolid waste or any other type of deposition upto 3 meter deep for cleaning in existing drain bed of culverts over the drain including cutting of small bushes, small tree girth not exc 30 cm and removal of muddy soil including small bushes, small trees girth not exc 30 cm including removal of RCC drain cover of any size and refixing the same under foul conditions including disposal of the excavated material duly covered during transportation out of MoD area, complete all as specified and directed by the Engineer-in-Charge.

De-watering of septic tanks/soakage wells of any size and any depth by pumping with trolley mounted pump sets including carrying the waste water in closed containers and unloading it out side the MoD land at location shown by Engr-in-Charge at a distance n. exc 15 km from the starting point including removing the existing manholes cover and replacing the same, septic tanks/soakage wells of any size/depth complete all as specified and as directed by the Engr-in-Charge Note:- (i) Hydraulically driven high pressure pump, capacity of 295L/min at 135 bar. (ii) Hydraulically driven high pressure pump, having 1850 cum/hr Suction Pressure. (iii) Rear hydraulic driven hose reel with 120m jetting hose. (iv) Proper safety of the operator during operation. (v) Rate shall be deemed to included in quoted rate.

Cutting and uprooting grass, vegetation shrubs, bushwood undergrowth, roots and trees not exceeding 30 cm girth surrounding manholes, gully trap, bend, wall pipe and overhead tank etc and levelling of ground around the manholes and removing rubbish to a distance exc 50 mtr and not exc 250 mtr and clear the site, complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and paving not exc. 15 cm thickness (below or above ground level), including removal of rubbish in low lying area, complete all as specified and directed by the Engineer in Charge.

Plain cement concrete (1:3:6), type C-2, using 40 mm graded mechanically crushed stone aggregates as in foundation filling and mass concrete, complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete (1:2:4) type B-1, using 20mm graded crushed stone aggregate as in Surface channels, drains and similar works, complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete (1:2:4) type B-1, using 20mm graded crushed stone aggregate as in coping, bands etc like incl weathering, slightly rounded or chamfered throating as directed incl form work (straight or curved) and finish all exposed surface facing of concrete , complete all as specified and directed by Engineer-in-Charge.

Extra for forming fair finished drain or channels n.exc 30 cm inner girth in cement concrete, using extra cement including form/moulds mittred/stopped end etc , complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre deep in soft/loose soil for foundations etc. or for cesspits etc. or for manholes not exc. 10 Sq. m on plan and not exc. 1.5 metre in depth or for shiftling existing sewage lines and getting out , complete all as specified and directed by the Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick, in soft/loose soil, complete all as specified and directed by the Engineer-in-Charge.

Removing excavated material to distance exceeding 250 metre but not exceeding 500 metre and depositing where directed at level not exceeding 1.5 metre above the starting point in soil, complete all as specified and directed by the Engineer-in-Charge.

Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc & removing debries out of MoD land, complete all as specified and directed by the Engineer-in-Charge.

Brick work with sub class 'B' , straight or curved on plan not exc 6m mean raidus built in cement mortar 1:6 , complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick walls or stone wall including raking out joints, hacking for key, scrubbing down with water etc., any description, including removal of rubbish in low lying area ,complete all as specified and directed by the Engineer in Charge.

Rendering 15 mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered wall surfaces and applying two coats of exterior acrylic emulsion paint (wheather proof) in camouflaging patterns over and including one coat of primer(antifungal), complete all as specified and directed by the Engineer-in-Charge.

Preparation of plastered wall surfaces i.e leveling/ edging the distrurbed places/edges using necessary filling compund of 3 mm thick (1.5mm in two coat) Birla / JK wall care putty to obtain smooth regular/ even finish using sand paper complete all as specified and directed by the Engineer-in-Charge.

Preparation of old surfaces of walls/ceiling including brooming down or steel wire brushing scraping down smoke soot, moulds mass and efflorescent salt and trading oil and greasy spots and applying two coat of oil bound distemper (approved shed) over one coat of primer complete all as specified and directed by Engr in charge.

Preparation of old surfaces of walls including brooming down or steel wire brushing scraping down smoke soot, moulds mass and efflorescent salt and trading oil and greasy spots and applying two coat of exterior acrylic emulsion (weather proof treatment) in camouflaging patterns (approved shed) over one coat of primer complete all as specified and directed by Engr in charge.

Water proofing layer with 604 Dr. fixit primeseal meets requirements of ASTM D 1227-87, Type-III standerd dilute with water in proportion of 2:1 and stir until a uniform consistency is achived and surface shall be clean all latitance, loose material, oil, grease etc and priming to external wall/ internal wall and ceiling as per manufaacture instruction complete all as directed by Engineeer-in-Charge.

Demolition of cement concrete (reinforced) of any description and in any position, (reinforcement cut as required to facilitate demolition), complete all as specified and directed by the Engineer in Charge.

Precast reinforcement cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate in man holes covers slabs/Shelves as in slabs supported on walls, beams and columns, in floors, roofs, landings, deck slabs and in shelves and like including necessary form work, complete all as specified and directed by Engineer-in-Charge.

Mild steel TMT bars 10mm dia and over cut to length bent shape as required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S, complete all as specified and directed by Engineer-in-Charge.

Dismantling of 150 mm bore SGSW drain pipes, with PCC haunching jointed in cement mortar and taking out of trenches if required and removal of existing sludge, complete all as specified and directed by the Engineer-in-Charge.

Plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes of 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed by the Engineer-in-Charge.

Salt- glazed stoneware drain pipe grade ‘A’ 150 mm bore, ISI marked jointed with cement mortar, laid in trenches and tested including pipe fittings such as bend, junction etc. of same grade, complete all as specified and directed by the Engineer-in-Charge.

Cutting into walls of existing manholes for connecting new drain pipe 150mm dia bore, making good to wall in CM (1:3)/ PCC (1:2:4) after inserting pipe, cutting out benching & forming branch channel in cement concrete (1:2:4) type B-1, reforming benching as required and rendering smooth finished, including removal of rubbish outside MoD land, complete all as specified and directed., complete all as specified and directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tilling including cement morter bedding (but not backing ),and removing serviceable tiles to store and rubbish off the premises , complete all as specified and directed by Engineer-in-Charge

Chequered cement concrete Coloured tiles 30cm x 30cm x 20mm thick set jointed and pointed in neat cement slurry in floors with in grey cement and pigment over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed by Engineer-in-Charge. Make- NITCO/UNISTONE/JOHNSON

First quality glazed ceramic coloured tiles of (300x200mm) x 7 mm thick, laid on vertical surfaces such as skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles ,complete all as specified and directed by the Engineer in Charge.

Granite (any type) 14-16 mm thick, work (table rubbed and polished) as in skirting/dado including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed of 10 mm thick in CM 1:4, complete all as specified and directed by the Engineer in Charge.

100 mm bore Cast Iron soil, waste and vent pipe, Spun pipe, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn laid in trenches or in floors, as in repair, complete all as specified and directed by the Engineer in Charge.

75 mm bore Cast Iron soil, waste and vent pipe, Spun pipe, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn laid in trenches or in floors, as in repair, complete all as specified and directed by the Engineer in Charge.

50 mm bore Cast Iron soil, waste and vent pipe, Spun pipe, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn laid in trenches or in floors, as in repair, complete all as specified and directed by the Engineer in Charge.

100 mm bore Cast Iron bend (any radius), diminishing piece or taper (larger bore measured), as in repairs, complete all as specified and directed by the Engineer in Charge.

75 mm bore Cast Iron bend (any radius), diminishing piece or taper (larger bore measured), as in repairs, complete all as specified and directed by the Engineer in Charge.

75 mm bore Cast Iron Tee/branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, as in repairs, complete all as specified and directed by the Engineer in Charge.

75 mm dia Cast Iron floor trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), as in repairs, complete all as specified and directed by the Engineer in Charge.

75 mm dia Cast Iron nahani trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate), as in repairs, complete all as specified and directed by the Engineer in Charge.

125 / 110 mm size PVC (SWR) gully trap, setting and jointing with solvent cement, as in repairs, complete all as specified and directed by the Engineer in Charge.

Demolition of cement concrete (un-reinforced) any description and laid in any position, complete all as specified and directed by the Engineer in Charge.

Plain cement concrete (1:5:10), type E-2, using 40 mm graded mechanically crushed stone aggregates as in filling of sunken floor and mass concrete, complete all as specified and directed by Engineer-in-Charge.

Rendering 20 mm thick in cement mortar 1:4 on sunken portion of floor / walls, finished the surface even and smooth with using extra cement, complete all as specified and directed by Engineer-in-Charge.

40 mm thick cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggreagate) as in floor finished even and smooth with using extra cement, complete all as specified and directed by Engineer-in-Charge.

M&L applying for Dr. Fixit bathseal system over the sunken portion floor of bathroom/toilet/kitchen, with the products in the "Kit' as per Item No 51.01 to 51.03, complete all as directed by Engineer-in-Charge. Note:- (i) Work Shall be carried out only authrosied applicator. (ii) In the case of non execution of work within 3days after demolition of sunken portion of toilet recovery will be effected 1000 Rs per day .

Dr. Fixit Bathseal Tape- Bituminous two sided adesive tape for wrapping around pipes inserted through wall and floor of existing sunken portion complete all as directed by Engineer-in-Charge.

Dr. Fixit bathseal Grout - Non Shrink expansive cementitous free flowing grout for filling gaps around bathroom pipes to fill in the gaps besides pipes complete all as directed by Engineer-in-Charge.

Dr. Fixit bathseal 2K WPC - Acrylic elastomeric cementitious waterproof coating for sunken portion Floor and walls in bathroom of existing sunken portion complete all as directed by Engineer-in-Charge.

CPVC 32mm pipes SDR 11 and plain CPVC SDR 11 for sunken spout pipe as in repair, complete all as directed by Engineer-in-Charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit writing etc and making good, cutting exc 10cm and n exc 20cm girth complete all as directed by Engineer-in-Charge.

Taking up or down 15 mm bore steel tubing with connections or fittings from wall, ceiling and floor etc., and removal from site, complete all as specified and directed by the Engineer in Charge.

Taking up or down 20 mm bore steel tubing with connections or fittings from wall, ceiling and floor etc., and removal from site, complete all as specified and directed by the Engineer in Charge.

CPVC 16mm dia pipes SDR 11 and plain CPVC SDR 11 including necessary fitting (Brass elbow, Brass Tee, Union) on walls/ceiling or laying in floors complete all as specified by Engr-in-charge. Make-Apollo/Finolex/Astral

Steel water tubes, 20 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors, complete all as specified and directed by the Engineer in Charge.

PVC valveless, syphonic action type flushing cisterns 10 ltrs capacity, low level, white, with inlet ball valves, float and handle including brackets and pvc flush pipe 32 mm dia for low level, fixed as in repair, complete all as specified and directed by the Engineer in -Charge Make-Cera/hindware/parryware

Vitreous china squatting pan Orissa pattern size 580x440mm white with integral foot rest (exclusive flusing cistern& flush pipe) including cast iron 'P' or 'S' trap of 100 mm bore pipe fixed in PCC 1:2:4 type B-2 and necessary lime concrete, fixed as in repairs, including making good the surface to match with existing floor finish fixed as in repair ,complete all as specified and directed by the Engineer in Charge. Make :- CERA/HINDWARE/PARYWARE.

Vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts flushing cistern and flush pipe) including plastic seat cover white and mild steel chromium plated aluminum hinging devices, connected to drains outlet, fixed as in repairs,complete all as specified and directed by the Engineer in Charge. Make-Cera/hindware/parryware

Bib taps fancy type chromium plated ,15 mm cast copper alloy with crutch handle or butter fly handle screwed down , screwed for iron pipe and fixed as in repair, complete all as specified and directed by the Engineer in Charge. Make -Jaquar/Hindware/prayag

Stop valve 15 mm dia cast copper alloy, angular decorative fancy type chromium plated, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair , complete all as specified and directed by Engineer-in-Charge. Make-Cera/hindware/parryware

Pillar taps, 15 mm bore cast copper alloy chromium plated fancy type, with capstan heads, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe fixed as in repair, complete all as specified and directed by the Engineer in Charge. Make-Cera/hindware/parryware

Chromium plated brass shower rose 125 mm bore of rim with swivel joint fixed as in repairs ,fancy type suitable for 15 mm bore pipe including shower arm chromium plated 15 mm dia, 195 mm long with bend of 45 degree including fixing to steel pipe or union, complete all as specified and directed by Engineer-in-Charge Make-Cera/hindware/parryware

Stainless steel grating 125mm dia fixed in repairs, complete all as specified and directed by Engineer-in-Charge

Grating round 125mm size of PTMT (minium weight 50 gram) fixed in repair , complete all as specified and directed by the Engineer in -Charge.

Wash basins, vitreous china, white, flat back of size 550x400 mm with pedestal including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets fixed as in repair , complete all as specified and directed by the Engineer in Charge. Make :- CERA/HINDWARE/PARYWARE.

SFRC manhole cover slabs medium duty of any shape and siz required and 65mm thick, fixed as in repair, complete all as directed by the Engr-in-charge.

Contract Amount shall be derived after affecting the amount of Schedule of Credit in General Summary on serial page No 15 of tender documents.

AK CONSTRUCTION

M/s JUGAL KISHORE MISHRA AND SONS

M/S Shree Ram Enterprises