GE 861 EWS-57/2022-2023

Amount

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar including all arches quoins etc but excluding ashlar facing, dressed stone work & precast concrete articles etc complete all as specificed and directed.

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed.

Demolition of cement reinforced concrete (reinforcement cut as required to facilitate demolition) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed.

Taking down chowkat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed.

Taking down of shutter any description area exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed.

Dismantling timber scantling unframed 40 sq cm and over in section in any position, complete all as specified and directed.

Dismantling of timber scantling under 40 Sqcm, fixed in any position in fillet rails, posts rafters purlin etc complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Dismantling boarding of any description, fixed in any position with nails, complete all as specified and directed.

Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar, complete all as specified and directed..

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc. 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m, in soft/loose soil and making good surfaces, complete all as specified and directed.

Returning filling in (soil) including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified and directed.

PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

RCC M-25 design mix using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides and soffits of floor or roof beam haunching , lintels, cantilevers shelves including supports overhangs etc also splays between floors and beams, etc complete all as specified and directed.

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

MS TMT bars 6-8mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

Hard core of broken stone or boulders of guage exc 63mm but n. exc 100mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:4, complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified.

15mm thick rendering on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified.

10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

75mm thick PCC 1:2:4, type B-1 (using 20mm graded crused stone aggregate) as in floors, finished even and smooth without using extra cement, complete all as specified.

50mm thick PCC 1:4:8 type D-2 (40 mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc., complete all as specified and directed.

Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

75mm thick PCC 1:4:8 Type D-2 (40 mm graded stone aggregate) as in sub-base of floors, complete all as specified and directed.

Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed.

60mm thick factory made machine pressed precast concrete, glossy finished coloured interlocking paver block with grey cement and pigment, any shape, size and design as approved by Engr-in charge confirming to IS 15658-2006, M-35 grade, complete all as specified and directed.

80mm thick factory made machine pressed precast concrete, glossy finished coloured interlocking paver block with grey cement and pigment, any shape, size and design as approved by Engr-in charge confirming to IS 15658-2006, M-40 grade, complete all as specified and directed.

Sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 300mm x 6-7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Vitrified tiles 10 mm thick, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed and including 10mm thick rendering in cement mortar 1:4 to receive, complete all as specified and directed.

Rolled mild steel in roof trusses (framed),trussed ,purlins,crane girders,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.

Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, etc., and similar small articles, conforming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10cm but n exc 15cm long and dia of neck 16mm to 20mm complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 15cm but n exc 30cm long and dia of neck 25mm, complete all as specified and directed.

35mm thick, 2nd class softwood factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.

35mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

6mm thick plywood, grade BWR, type BB, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in walls with nails to timber frame, complete all as specified and directed.

20mm thick, 2nd class hardwood boarding in any situation (except flooring or skirting) planed one side with butt joints and fixed with nails supplied and fixed "as in eves board", complete all as specified and directed.

2nd class softwood, as in scantling and similar work, clean sawn, timber fixed in position, complete all as specified and directed.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 6 Sqcm but n exc 13 Sqcm complete all as specified and directed.

0.63mm thick galvanised corrugated mild steel sheeting with two corrugated side lap fixed with L type or J type hook bolts in roofs, walls etc. with grade of zinc coating 275, complete all as specified.

Description all as per item No 60 here in before but except sheet complete all as specified.

0.80mm thick plain galvanised mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plaind steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

250mm size mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed.

100mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed.

150mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.

125mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.

100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

75mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed.

S&F in repair 300mm size MS helical door spring including roller & roller plate, complete all as specified & directed.

Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

All as per the description of item No. 74 here-in- before but except tubing.

Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, flat back of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm dia brass chromium plated waste fitting with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, seat cover and fixing bolts, flushing cistern and flush pipe & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and as directed.

10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets (fixed in repair), complete all as specified and directed.

S & F in repair PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S & F repair 15mm bore pillar tap, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repair 15 mm bore brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixeds, complete all as specified and directed.

S & F in repair 15mm bore bib tap, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F in repairs 15mm bore stop valves, fancy type, chromium plated with long long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.

Preparation of old plastered surfaces of wall and applying one coat of cement base paint, complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Preparation of old surfaces of walls including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper on walls, complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old painted steel surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody for reuse if serviceable or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Concealed Point wiring complete with 1.5 sqmm 1100 graded PVC FRLS (Multistrand) insulated unsheathed copper conductor single core multi strand flexible cable maintaining colour coding (Phase- Red/yellow/Blue, Neutral- Black), including single core multistranded copper conductor 1.5 sqmm size cable (green colour) as earth continuity wire connected to common earth dolly to modular concealed box and white cover plate of required nos and required size for housing switches, sockets etc for one light / fan/ bell point controlled by one switch one way including modular concealed box and white cover plate of required nos and size finishing of slots by means of cement mortar 1:3 making good to existing surface of the wall and touching with three coats of existing colour of wall and making good disturbed surface complete, complete all as specified and directed.

All as per srl item No-95 here in above but for one 3 pin 5A socket outlet independent controlled by one switch, complete all as specified and directed.

All as per serial item No-95 here-in-before but for 3 pin 15 Amps socket outlet independent board with 2.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specified and directed.

Switch piano flush button types 6 Amp, single pole, one way complete all as specified and directed.

Switch socket combination 2 in 1, 3 pin, 6 Amp flush type, universal, complete all as specified and directed.

Switch socket combination 2 in 1, 3 pin, 6 and 16 Amp, flush type universal, complete all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular suitable for batten fittings, complete all as specified and directed.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/ Polycarbonate, isolated body, complete all as specified and directed.

LED lamp 7 W, complete all as specified and directed.

LED lights fitting 1x18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

MCB Distribution board , 240 volts TPN , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 8 ways, IP-43 protection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

MCB, SP, AC, 240 volts "C" series capacity of 06 to 32 Amps, 10kA and making connections, complete all as specified & directed.

MCB, SPN, AC, 240 volts "C" series capacity of 40 to 63 Amps, 10kA and making connections, complete all as specified & directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by (-) 9.0%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

M/S SHEIKH FEROOZ AHMAD

M/S Manzoor Constructions

JANDOO AND CO.

NAJAR ENTERPRISES