Ed.Ctp school improvement 2024-25 20.00

Amount

Chipping of concrete and roughening the surface cost and conveyance of all materials to site and all labour charges etc.. Complete

Special ceiling Plastering in Cement Mortor 1:3 Mix (one Cement, Three M- Sand ) 10mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications-10 m2.

Plain Cement Concrete 1:4:8 Mix (one Part of cement, four Part of M- Sand and Eight Part of aggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete as per TNDSS NO : 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge.

Plain Cement Concrete 1:1½:3 Mix (one Part of cement, One and half Part of M- Sand and three Part of aggrigate) using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc., complete as per TNDSS NO: 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge.

Clean removal of cement plaster from walls and racking out joints 20mm deep

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification- 100CFT

Plastering with cement mortar 1:3 (One part of Cement and three part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Dismantiling Pressed tiles & weathering course including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications

Supplying and Fixing of Solar Reflective Ceramic Tiles cost and conveyance of all materials to site and all labour charges etc.. Complete

Providing granolithic floor finish of 25mm thickness with plain cement concrete 1:2:4 (One Cement, Two crushed sand (M-Sand) and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Dadooing walls with ceramic tiles of sizes 300mm X 450mm X 8mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Dismantling and removing of old damaged Pantile or Mangalore Tiled Roof without Roof Timbers including cost and Conveyance of all materials to site and all labour charges for filling etc., Complete

Supply and fixing of Puff roof panels made up of minimum 0.30mm thick PPGI Corrugated sheet at the top over plain sheet at the bottom with a layer of rigid CFC Free Polyurethene Foam (PUF) of density 40kg +2kg/cm as insulation in between.The polyurethene foam shall conform to latest IS 12436.The minimum thickness PU foam layer shall be 29mm for 30mm thick PUF Panel .The PPGI sheet shall be of minimum 240 MP & Steel garde and shall have a zinc coating of minimum 120 GSM as per IS 277/1992,5-7 Micros of epoxy primer on both sides of the sheet and polyster top coat of 18-19 micros of one side/outer side.The PPGI sheet/PUF panels shall have a protective guard film of minimum 20-25 micros to avoid scratche tc finished panels during transfortation ,providing ridges or hips of with plain G.S Sheet fixed with polymer coated J or L hooks ,bolts and nuts 8mm dia G.I limpet and bitumen washers etc,complete excluding the cc of trusses ,purlines inclusive of cutting to the shape where ever required.

Painting the new walls two coats over one coat of priming with best Emulsion paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by the department officers etc., complete complying with standard specifications.

Manufacturing supplying and fixing of MILD STEEL DOOR made out of 50 x 50 x 6 mm M.S angle for outer frame,35 X 35 X 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets (18 G) with 5Nos, of stiffners using M.S.Flats of size 25 X 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase of Double shutters of 125 X 31 X 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 X 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers.

Manufacturing supplying and fixing of MILD STEEL Window made out of 40 x 40 x 6 mm M.S angle for outer frame, 35 X 35 X 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets ( 18 G ) with 5Nos,of stiffners using M.S.Flats of size 25 X 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase of Double shutters of 125 X 31 X 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 X 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Roofing with Galvanised Coruugated Iron Sheet of 0.8mm thickness - 10 m2

Painting one coats over the old iron work using ready mixed enamel paint including cost of all materials to site and all labour charges for mixing applying etc., Complete as per Standard Specifications Rate for 10 Sqm

supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Lower end) with 2 module 100W fan step regulator (Lower end) with 1 metre down rod on the existing fan clamp(sd485)

Supplying and Fixing of 7W / 9W LED Bulb cost and conveyance of all materials to site and all labour charges etc.. Complete

Supply and Fixing of PVC Screw Down Tap Heavy Type 20mm dia

Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,-1000 lit

supply and Fixing of 63mm PVC pipe 6kg /cm2 pipe connection works including cutting, threading and fixing charges etc.

GS CONSTRUCTION (BID ID -1176062)