ADDITION/ ALTERATION AND SPECIAL REPAIRS TO QUARTER NO P-16A AND P-16C AT NOFRA AT INS MANDOVI UNDER GE (P) NAVY MANDOVI

Amount

BUILDING PORTION

Taking down cement or cement lime plaster, any description on stone/ PCC block/ brick wall or top of chajja including raking out joints, hacking for key, scrubbing down with water etc and removal of debris to outside of INS Mandovi area including filling of open joints in cement mortar 1:6 complete all as specified and directed.

M & L for dubbing out average 20 mm thick on irregular face of external and internal wall surfaces (when specifically ordered in writing) in CM 1:6 complete all as specified and as directed.

M & L for rendering 15 mm thick in two layers in cement mortar 1:3, 10 mm thick first layer and 5 mm thick outer layer mixed with WPC as per manufacturer's instructions on fair faces of brickwork or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: WPC shall be measured and paid separately.

Supply only integral waterproofing compound complete all as specified and directed.

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 5 mm thick in cement mortar 1:3 on ceiling surfaces finished even & smooth, without using extra cement complete all as specified and directed.

M & L for preperation of newly plastered wall surfaces, ceiling cornices etc, making surface smooth by applying 1 mm thick ready mix putty where ever required and applying two coats of acrylic emulsion exterior paint of approved shade, over a coat of primer, including necessary scaffolding complete all as specified and directed.

M & L for preparation of newly plastered wall surfaces, priming with alkali resistant priming paint, applying 1 mm thick wall care putty wherever required and distempering with two coats of distemper oil emulsion, white or tinted, complete all as specified and directed.

M & L for complete removal of existing treatment including preperation of old lastered wall surfaces preparatory to distempering, applying 1 mm thick acrylic wall care putty, priming the surface with alkali resistant priming paint and distempering with two coats of distemper oil emulsion, white or tinted complete all as specified and directed.

M & L for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M & L for preparation of old plastered ceiling surfaces and applying two coats of white wash complete all as specified and directed.

M & L for preparation of old decorative wall surfaces, ceiling cornices etc by brooming, scrapping down dust particle, smoke soot, moulds, moss and efforescent salts etc, making surface smooth by applying ready mix putty where ever required and applying two coats of acrylic emulsion exterior paint complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises to a distance exc 250 m and not exc 1000 m, spread and levelled, complete all as specified and directed.

M & L for 15mm thick screed bed or bedding layer of cement mortar 1:3 for laying floor finishes for kota stone complete all as specified and directed.

M & L for rendering 10 mm thick on fair faces of brick work or concrete vertical surfaces in cement mortar 1:4 complete all as specified and directed.

M&L vitrified ceramic tiles light shade 600 x 600 x 10 mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles all as specified and directed

M & L for providing non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for providing for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for providing machine cut kota stone slab flooring 20 - 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for providing granite (of any type) tiles, 20mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including griding and polishing complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed.

M & L for providing vitrified ceramic tiles, light shade, 600 x 600 x 10 mm thick (square/rectangular), polished, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for providing non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for glazed ceramic coloured tiles in vertical surface, 350 x 250 x 7 mm/ 450 x 350 x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 sqm each, with shutters (without taking off shutters from the frames) complete all as specified and directed..

Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4.0 sqm each, with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 2nd class hard wood plain, framed, panelled shutters (any number of panels), 40mm thick, with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: fitted to chowkats complete all as specified and directed.

S & F 2nd class hard wood, 30 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and directed.

M&L for 2 coats of painting with synthetic enamel paint over a coat of pink Primer on new wooden surfaces of any description, not otherwise descri-bed, over 10cm width or girth including preparation of new surfaces.

M & L for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S & F 100 mm X 63 mm size factory made FRP door frame, with 2mm thick FRP lamination, core made of polyurethane foam/ high density (more than 40kg per cubic meter) and cellular foam done in situ, frame fixed on either side with 3 Nos MS flat iron 25mm x 3mm, cut to size and made to shape, fixed with hold fast after necessary tarring and sanding including provision of second class wooden blocks to hold the fittings and fixed as per manufacturer's instructions complete all as specified and directed. Note: Size of the chowkats shall be inclusive of 2mm thick FRP lamination.

S & F factory made panelled FRP door shutter, 30 mm thick with 2 mm FRP lamination top rail of size 30 x 150 mm; lock rail & bottom rail of size 30 x 150 mm with 12 mm thick panels of FRP section of box type construction as per IS 4020, core made of polyurethane foam / high density (more than 40 kg per cubic meter), cellular foam done in-situ and fixed in position as per manufacturer's instructions and including the 03 nos 100 mm long butt hinges, 02 nos aluminium anodised 200 mm long barrel tower bolt, 02 nos aluminium anodised 150 mm size bow handles and 01 no aluminium alloy anodized sliding door bolt with hasp and staple (bolt type) complete all as specified and directed.

Taking down steel tubing and connections of 15 mm dia bore complete all as specified and directed.

Taking down steel tubing and connections of 20 mm dia bore complete all as specified and directed.

Supplying and laying of CPVC pipes of 20 mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed.

Supplying and laying of CPVC pipes of 25 mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed.

S & F aluminum powder coated window/ ventilator shutter including frame, any type (sliding or open-able) and other similar work etc, fabricated, by using sections, including necessary arrangement to receive 4mm thick sheet glass or wire mesh with aluminium channel beading, stainless steel screws, rollers, maruti lock including the cost of rubber gasket / rubber beading, rollers, maruti lock etc, fixing frames complete all as specified and directed. Note: Weight of rubber gasket / beading rollers, maruti lock will not be measured with weight of aluminium shutter. Note: Sheet glass & wire mesh shall be measured and paid separately.

S & F powder coated aluminium grill of design DG-104 pattern, made out of 10mm dia rod fixed with and including standard aluminium frame of 'F' section of size 23.4 x 15.3 x 1.4 mm thick all as per manufacturer's instructions complete all as specified and directed.

S & F 4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares exc 0.5 sq. m in each pane complete all as specified and directed.

S & F 4 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples on wooden doors complete all as specified and directed.

S & F in repairs curtain rails of anodised aluminium alloy with fixing brackets, stops, rollers etc complete all as specified and directed.

S & F in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm dia bore complete all as specified and directed.

S & F in repairs pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe of 15 mm dia bore complete all as specified and directed.

S & F in repairs bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm dia bore complete all as specified and directed.

S & F PVC connections of size 15 mm, 450 mm long with PTMT nuts complete all as specified and directed.

S & F in repairs PTMT soap dish of approximate size 160 x 160 x 90 mm embedded in wall complete all as specified and directed.

S & F in repairs brass, tubular towel rail, chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S & F in repairs wash basins, vitreous China, white, flat back, 550 x 400 mm size including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S & F in repairs wash basins, vitreous China, white, flat back, 630 x 450 mm size including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S & F in repairs PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets and 32 mm dia flush pipe of polyethylene of low or high density or PVC and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed.

S & F 2 in 1 health faucet with hook, chromium plated, with 1.5 m tube complete all as specified and directed.

S & F in repairs brass chromium plated shower rose, 125 mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S & F in repairs ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 25 mm dia bore complete all as specified and directed. (minimum weight 25 mm - 455 gm)

S & F ball valves to CPVC pipe of 25 mm dia bore complete all as specified and directed.

S & F in repairs tank adaptor to CPVC pipe of 25 mm dia bore complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S & F 75 mm dia bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 110 mm dia bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

M & L for PVC (SWR) multi floor trap of 75 mm dia outlet, with grating including jointing with solvent cement, fixed in repairs, complete all as specified and directed.

S & F 50 mm dia high density polyethylene (HDPE) pipes of pressure rating 6kgf/cm2 fixed complete to walls, ceilings or in floors including necessary fittings complete all as specified and directed.

S & F PVC (SWR) bends of 110 mm dia bore, any radius, with acess door complete all as specified and directed.

S & F PVC (SWR) bends of 75 mm dia bore, any radius, with acess door complete all as specified and directed.

S & F PVC (SWR) junction single (single T) of 110 mm dia bore, equal or unequal, with acess door complete all as specified and directed.

S & F PVC (SWR) junction single (single T) of 75 mm dia bore, equal or unequal, with acess door complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M & L for providing 75 mm thick cement concrete 1:3:6 type C-2 (using 40mm graded aggregate) as in plinth protection, finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M & L for providing chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors (over plinth protection) with grey cement and pigments complete all as specified and directed.

M & L for chipping, removing carefully concrete work using low impact hammer, breaking without damaging the structure & cleaning and disposing off debris outside the premises complete all as specified and directed. Note: Hard concrete shall not be removed by force.

M & L for cleaning existing reinforcement with wire/ rotary wire brush, making the surfaces free of loose material, rust spalls, dirt etc, applying two coats of alkaline rust converting primer FEOVERT, confirming to ASTM-B-117, on rebars, with time interval of 6 hour between each coat) and applying protective coating of IPNET-RB complete all as specified and directed.

M & L for injecting of cement slurry grout in 1:2 ratio (1 part cement, 2 parts water) including super plsticizer (Supercom-100) 250 ml/50 kg into prefixed nozzles in the walls and slabs by means of pump at a pressure of 0.5 Kg/cm2 till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled complete all as specified and directed. Note: Mixing shall be done using mechanical mixer continuously stirring mechanically to keep cement particles in suspension.

M & L for injecting low viscosity MONOPOL (3-5 cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories, till nozzles refuse to accept the grout, including mixing of material components (Part a & b) in quantities as per manufacturer's instruction by weigh batching, grouting by maintaining the pressure at exit (0.5 to 1.0 kg/cm2) by monitoring pressure guage at exit, grouting the material through prefixed nozzles in the structural elements @ 100ml per nozzle and repeating the process for all the nozzles (beam and columns) complete all as specified and directed.

M & L for drilling and fixing Rohibb Teflon nozzles in RCC structural members, including drilling holes of 12mm dia, 50 to 100mm deep holes in structural members at intervals of 500 center to center in staggered manner and carrying out the work as under complete all as specified and directed. (i) Cleaning of holes : Holes shall be cleaned by air blower prior to fixing nozzles. (ii) Fixing of nozzles : 12mm dia Rohibb Teflon nozzles shall be inserted in cleaned holes. External end of nozzles to be machine cut to receive outlet of grouting gun. Nozzles shall be fixed inside the holes by applying thixotropic epoxy putty to ensure complete sealing. The system shall be cured for min 12 hrs. (iii) Cutting of nozzles : Nozzles shall be cut by chisel after completion of grouting without damaging structural elements.

M & L for rendering 5 mm thick over gunniting / concrete surface in cement mortar 1:4 and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for providing and applying jacketing around columns with micro concrete (Molith-MC) M40 including lifts, shuttering, drilling holes and fixing shear anchor complete all as specified and directed. Note: Reinforcement shall be measured and paid separately. (Quoted rates shall be deemed to be inclusive of jacketing, formwork and micro concrete)

M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S & F brass rat tail rod patern springs, 300 mm long, including roller and roller plate complete all as specified and directed.

S & F aluminium anodised, barrel tower bolts of extruded section and 200 mm length complete all as specified and directed.

S & F extruded aluminium alloy handles, 200 mm long, fabricated type, anodised complete all as specified and directed.

S & F 100 mm long butt hinges, stainless steel complete all as specified and directed.

S & F floor door stopper of aluminium alloy body and tongue, anodised with hard draw steel spring, 150mm overall length of cover plate complete all as specified and directed.

S & F mild steel clamps; hold fasts; wall ties and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M & L for providing PCC 1:3:6 type C1 using 20mm garded stone aggregate, for fixing hold fast complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S & F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete for Gde Fe 410 (E-250 quality-A) complete all as specified and directed.

S & F in repairs sinks made of stainless steel 1 mm thick, kitchen or laboratory with plugs, washers and wastes; includding bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, of overall size 495mm x 420mm and of bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs stainless steel plate/ utensil rack of 900 x 600 x 300mm size made of 1 mm thick steel including high quality hooks for hanging utensils complete all as specified and directed.

S & F in repairs PTMT bathroom mirror cabinet of size 600mm x 450mm x 200mm including all necessary arrangements for fixing to wallcomplete all as specifeid and directed. Make: Shakthi Cat Pt No SB -155 or Water Tec/ or equivalent make

SEWAGE DISPOSAL

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/ disintegrated rock complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/ disintegrated rock complete all as specified and directed.

Removing excavated material to a distance n exc. 50 m and depositing where directed complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or PVC) of 150/ 160 mm dia, set in cement mortar, complete all as specified and directed.

M & L for concrete bed to drain pipes of 160 mm bore including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:3:6 type C2 complete all as specified and directed.

S & F PVC (SWR) pipes of 160 mm dia bore, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M & L for pre-cast cement concrete block masony with solid blocks of precast cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate), exc 10cm in width and set in cement mortar 1:6 complete all as specified and directed.

M & L for pre-cast cement concrete block masony with solid blocks of precast cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate), exc 10cm in width and set in cement mortar 1:6, except block complete all as specified and directed.

M & L for providing cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; copings, benching to manholes, kneelers, apex stones, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

M & L for providing precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throating etc. and setting in mortar 1:4 complete with joints to match complete all as specified and directed. Note: Reinforcement steel shall be measured and paid separately under relevant item of Schedule 'A'.

S & F mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

INTERNAL ELECTRIFICATION

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc to match existing surface complete all as specified and directed.

Taking down DB, main switch, sheet metal enclosure etc complete all as specified and directed.

Taking down submain wiring complete all as specified and directed.

M & L for point wiring complete with 1.5 Sqmm 1100 volts grade single core PVC insulated FRLS unsheathed cable with multistranded copper conductor confirming to IS-694, Part II, ISI marked, drawn through and including medium grade PVC conduit of size not less than 25mm dia, ISI marked with all accessories, concealed in wall/ ceiling, sunken switch / terminal box 1.12 mm thick, suitable for 3mm thick laminated hylem sheet or plastic masonite laqminated sheet top cover fixed with chromium plated brass screws for fixing switches, sockets, regulators etc., and including providing 1.5 sqmm 1100 volts grade single core PVC insulated FRLS unsheathed cable with multistranded copper conductor in green colour as earth continuity conductor connected to common earth dolly for the following complete all as specified and directed. Note: Quoted rate shall be deemed to be inclusive of cutting chasis in wall/ floor/ ceiling and making good disturbed surface with PCC work and paint etc.

One light point controlled by one switch

One ceiling/ exhaust fan point controlled by one switch

One socket outlet 5 Amp on same board with other switches

One socket outlet 5 Amp on independent board

One bell point

M & L for point wiring complete with 2.5 Sqmm 1100 volts grade single core PVC insulated FRLS unsheathed cable with multistranded copper conductor confirming to IS-694, Part II, ISI marked, drawn through and including medium grade PVC conduit of size not less than 25mm dia, ISI marked with all accessories, concealed in wall/ ceiling, sunken switch / terminal box 1.12 mm thick, suitable for 3mm thick laminated hylem sheet or plastic masonite laqminated sheet top cover fixed with chromium plated brass screws for fixing switches, sockets, regulators etc., and including providing 2.5 sqmm 1100 volts grade single core PVC insulated FRLS unsheathed cable with multistranded copper conductor in green colour as earth continuity conductor connected to common earth dolly for one 3 pin 15 Amps switch socket combination on independent board complete all as specified and directed. Note: Quoted rate shall be deemed to be inclusive of cutting chasis in wall/ floor/ ceiling and making good disturbed surface with PCC work and paint etc.

S & F in repairs switch piano, 5 amp, single pole, one way, flush type, complete all as specified and directed.

S & F in repairs lamp holder PVC/ polycarbonate type with cord grip cap suitable for batten fittings complete all as specified and directed.

S & F in repairs bell buzzer/ Ding dong 240 Volts complete all as specified and directed.

S & F in repairs bell push, flush type 5 Amps complete all as specified and directed.

S & F in repairs switch socket combination 5 pin and 5 Amps, flush type complete all as specified and directed.

S & F in repairs switch socket combination 5 pin and 15 Amps, flush type complete all as specified and directed.

S & F in repairs LED tube light fitting 1 X 20 watt, 220V AC decorative box type with driver and holder, including LED tube light, connecting with three core flexible copper conductor cable of suitable size from ceiling rose to fitting duly mounted on PVC block with steel screw complete all as specified and directed.

S & F in repairs LED tube light fitting 1 X 10 watt, 220V AC decorative box type with driver and holder, including LED tube light, connecting with three core flexible copper conductor cable of suitable size from ceiling rose to fitting duly mounted on PVC block with steel screw complete all as specified and directed.

S & F in repairs LED bulbs, 9 Watt, warm white complete all as specified and directed.

M & L for taking down and refixing ceiling fan after replacement of capacitor, rubber bush, fixing clamp and painting with white colour synthetic enamel paint complete all as specified and directed.

S & F in repairs MCB SP 6 to 32 Amps, 240 Volts, 'C' series, complete all as specified and directed.

S & F in repairs ceiling rose, 2 to 3 terminal, surface bakelite, 65X50 mm, complete all as specified and directed.

S & F sheet metal enclosure for MCB's (D.B), double door, TPN 4 way, 415 Volts, with suitable rated busbar complete all as specified and directed.

S & F in repairs MCB TP, 63 Amps, 415 Volts, 'C' series complete all as specified and directed.

S & F in repairs MCB TPN, 50 Amps, 415 Volts, 'C' series complete all as specified and directed.

S & F in repairs exhaust fan, 300 mm sweep single phase 230/240 volt AC supply 50 HZ, PVC body with louvers, with suitable MS Bracket, nuts, bolts and fixing arrangement, including resizing holes and PCC work as per site requirement complete all as specified and directed. Make :- Bajaj Maxima 300mm or equivalent as specified in List of Manufacturers

S & F in repairs exhaust fan, 300 mm sweep single phase 230/240 volt AC supply 50 HZ, metal body with louvers made of iron and aluminium flaps, with suitable MS Bracket, nuts, bolts and fixing arrangement, including resizing holes and PCC work as per site requirement complete all as specified and directed.

M & L for submain wiring with four runs of 6 sqmm single core multistranded PVC insulated unsheathed cable 1100 Volts with copper conductor and one run of 6 sqmm single core PVC insulated unsheathed cable 1100 Volts with copper conductor as continuous earth wire drawn through and including rigid PVC conduit of suitable dia concealed in wall/ceiling with all accessories such as tees, elbows, junction boxes, reducers etc as required and connecting to existing main switch board/ distribution board and testing on completion complete all as specified and directed. Note: Four runs of 6 Sqmm cable, one run of 6 Sqmm earth wire and one run of PVC conduit shall be measured as unit run.

M & L for submain wiring with two runs of 4 sqmm single core multistranded PVC insulated unsheathed cable 1100 Volts with copper conductor and one run of 4 sqmm single core PVC insulated unsheathed cable 1100 Volts with copper conductor as continuous earth wire drawn through and including rigid PVC conduit of suitable dia concealed in wall/ceiling with all accessories such as tees, elbows, junction boxes, reducers etc as required and connecting to existing main switch board/ distribution board and testing on completion complete all as specified and directed. Note: Two runs of 4 Sqmm cable, one run of 4 Sqmm earth wire and one run of PVC conduit shall be measured as unit run.

S & F sheet metal enclosure earth plug and socket, single pole and neutral with two pin including one single pole MCB 20 Amps 240 Volts complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground, earth pit not less than 2.25 m below ground level, with top edge of plate not less than 1.5 m below ground level, connected to 4mm dia GI earth wire by means of bolts, nuts, check nuts and washers of galvanised steel including neccessary earthwork and excavation in any strata, PCC chamber in PCC 1:3:6 type C2, 20 mm dia light grade GI pipe for protection of earth strip and GI wire, chamber cover etc all as per electrical plate No. 3 of SSR Part-I including connections with earth testing point complete all as specified and directed. Note: On testing after completion if the desired earth resistance is not obtained, earthing shall be redone at no extra cost.

SHREE SAI LABOUR CONTRACT CO-OPERATIVE SOCIETY LTD

STAR FABRICATION

SHIVRAJ CONSTRUCTIONS

M/S. M M S ENTERPRISES

M/S NAGINENI RANGA RAO