Improvement and retrofitting to various LWSS / GWSS under Jal Shakti Section Arki in Tehsil Arki Distt. Solan (HP)

Amount

Excavation in foundation, trenches etc. earth work in all type of soil such as pick work, jumper work, blasting work kankar,mooram singles including decomposed soft and hard rock etc. upto all heights stacking the excavated earth not more than 3 metres clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths and sides of foundation etc.consolidating each deposited layer by raming and watering and then disposing of all surplus excavated earth upto all leads and lifts as directed by the Engineer in charge complete in all respects.

Providing and laying cement concrete 1:4:8(1 Cement :4Sand : 8 graded stone aggregate 40mm nominal size)and curing complete excluding the cost of form work in foundation and plinth including all carriage of materials upto all leads and lifts complete in all respect.

Providing and laying cement concrete 1:6:12(1 Cement :6 Sand : 12 graded stone aggregate 40mm nominal size)and curing complete excluding the cost of form work in foundation and plinth including all carriage of materials upto all leads and lifts complete in all respect.

Providing and laying cement concrete work 1:2:4(1 Cement :2 Sand: 4 graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

foundation,footings and bases of columns etc. including all leads and lifts complete in all respect.

In columns, pillars,posts and strutus square, rectangular or polygonal in plan including all leads and lifts complete in all respect

Suspended floors, roofs,landings,shelves and their supports,balconies,beams, and girders,bressumers and cantilevers upto floor two level including all leads and lifts etc.complete in all respects.

Stair cases (except spiral stair cases) excluding landing i/c preparation of surface including carriage of materials up to all leads and lifts complete in all respects.with sloping or stepped soffits excluding landings including all leads and lifts complete in all respect.

Providing and laying cement concrete 1:3:6(1 Cement :3 Sand : 6 graded stone aggregate 20mm nominal size)and curing complete excluding the cost of form work in foundation and plinth including all carriage of materials upto all leads and lifts completein all respect.

Providing and laying cement concrete 1:1:2 (1cement :1 sand : 2 graded stone aggregate 20 mm nominal size) & curing complete excluding the cost of form work & reinforcement for reinforced concrete work in :-

foundation ,footing,bases of columns and the like and mass concrete including all leads and lifts complete in all respect.

walls(any thickness but not less than 0.10 meters thickness) attached pilasters ,buttresses, plinth and string courses etc. from top of foundation level upto floor two level including all leads and lifts complete in all respect.

Flat surface such as soffits of suspended floors,roofs,landings and the like floors etc. upto 200mm in thickness including all leads and lifts etc.complete in all respects.

Arches upto floor two level beyond 6.00 meters including all leads and lifts complete in all respect.

Providing and laying cement concrete in M 30 design Mix aggregate 20mm nominal size)and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :-

foundations ,footings bases of columns and the like and mass concrete work complete in all respects

Walls any thickness (but not less than 0.10meter thickness) including attached pilasters,buttresses plinth and string courses etc. from top of foundation(level) upto floor two level including all leads and lifts etc.complete in all respects

Providing form work with mild steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for insitu reinforced concrete work and plain concrete work in:

Foundation ,footings,basis of columns etc. and mass concrete including all leads and lifts complete in all respect.

columns, pillars,posts and strutus square,rectangular or polygonal in plan including all leads and lifts complete in all respect

Beams, cantilevers,girders and lintels sides and soffits of beams, beam haunchings, cantilevers,bressumers and lintels not exceeding 1.00 meters in depth r including all leads and lifts complete in all respect

Flat surfaces such as soffits of suspended floors,roofs,landings and the like floors etc. upto 200mm in thickness including all leads and lifts etc.complete in all respects.

Vertical surfaces such as walls(any thickness )partition and the like including attached pillasters, buttresses plinth and string courses and like including all leads and lifts etc. complete in all respects.

Slopping or battering surfaces including folded plates where inclination to horizontal does not exceed 30 degree including all leads and lifts complete in all respect

Edges of slab including all leads and lifts complete in all respects

Stair cases with sloping or stepped soffits excluding landings including all leads and lifts complete in all respect

Prov.form work of ordinary timber plankings so as to give a rough finish i/c centring, shuttering,strutting & propping etc. ht.of propping & centring below supporting floor to ceiling not exceeding 4 mts. & removal of the same for insitu-reinforced concrete & plain concrete work in :-

Arches beyond 6.00 mtr. Span i/c carriage of materials up to all leads and lifts

Providing RCC work smooth finishing of the exposed surface with cement mortor 1:3(1Cement:3Sand) including carriage of materials upto all leads and lifts complete in all respects.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level including cost of binding wires and carriage of materials upto all leads and lifts complete in all respects.

Half brick masonry in common burnt clay building bricks in Cement motor 1:4(1 Cement 4 sand) including all leads and lifts complete in all respect.

2nd class bricks.

Providing and fixing pressed steel door,frames , manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jamb block jamb,beed and if required angles threshold of mild steel angles of section 50x25mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means adjustable lugs with split and tails to each jamb including steel but things 2.5mm thick with guards lock strike plate and shock as specified and applying a coat of applying steel primer after pretreatment of the surfaces directly by the Engineer in charge.

Profile - A

Profile- B

Profile- C

Providing and fixing panelled and glazed shutters for doors windows and clearestory windows including black enameled iron butt hinges with necessary screws 40mm thick 2nd class deodar wood including all leads and lifts complete in all respect.

Providing and fixing wire gauge shutters using galvanised MS wire gauge of IS gauge designation 85 G with wire of dia 0.56 mm for doors windows clerestory windows including bright finished black enameled iron hinges with necessary screws 40mm thick 2nd class deodar wood including all leads and lifts complete in all respect.

15mm thick cement plaster in single coat on rough side of brick/stone /concrete walls for interior plastering upto floor two level including arrises, internal rounded angles,chamfers and /or rounded angles not eexceeding 80mm in girth and finished even and smooth in :-

In Cement mortor 1:6(1 Cement :6 Sand)

20mm cement plaster in single coat on the rough side of brick/stone masonry for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and or rounded angles not exceeding 80mm in girth and finished even and smooth lincluding all leads and lifts complete in all respect

Cement motar 1:6(1 Cement : 6 Sand)

6mm cement plaster to ceiling including all leads and lifts complete in all respect

In Cement mortor 1:3(1 Cement :3 Sand)

White washing with lime on undecorated wall surfaces (two coats) to give an even shade including thoroughly brooming the surface to remove all dust dirt and other foreign matter complete in all respect.

Distempering(two coats) with oil bond washable distemper of approved brand and manufacture and of required shade or undecorated wall surface to given an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer including all leads and lifts complete in all respect.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces(two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials complete in all respect.

Pre cast terrazzo tiles 20mm thick (with marble chips of specified size laid in floor treads of steps and landing on a bed of 10mm average thickness cement mortar 1:6(1 Cement :6 Sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles(where ever required) silvery grey including rubbing and polishing complete in all leads and lifts complete in all respect.

In Skirting & riser ofsteps and dado in C.M 1:3 (1Cement : 3 Sand) jointed with white sulary, silver gray .

Applying priming coat over new wood and wood base surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter, sand papering and knotting etc.. With ready mixed paint brushing wood primer pink including all leads and lifts complete.

Painting two coat (excluding priming coat) on new wood and wood based surface with ready mixed paint brushing to give and even shade including cleaning the surface of all dirt,dust and other foreign matter sand papering and stopping etc. with white paint including all leads and lifts complete in all respect.

Painting two coat (excluding priming coat) on new wood and wood based surface with ready mixed paint brushing to give and even shade including cleaning the surface of all dirt,dust and other foreign matter sand papering and stopping etc. other than white including all leads and lifts complete in all respect.

Providing and fixing of M.S. grill of required pattern in wooden frame of window etc. with MS rounded headed bolts and nuts and screws plain grill including all leads and lifts complete in all respect.

Plain grill.

Stone soling properly hand packed filling interstices with spalls and consolidating with power road roller to the required gradient and camber including sperading watering and rolling of binding materials moorum or earth etc. 100mm spread thickness (finished work including materials and labour) as directed by thee Engineer- in Charge with in all leads and lifts complete in all respects.

Providing and fixing anodized aluminum sliding door bolts with nuts and screws complete in all respect.

Providing and fixing anodized aluminum tower bolts barrel type with screws etc. complete in all respect.

200mm x 10mm

Providing and fixing anodized aluminum handles complete in all respect.

Providing and fixing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm dia meters bolts nuts and wooden plug and embedding in cement concrete block 30x10x15cm 1:3:6(1 Cement :3 Sand: 6 graded stone aggregate 20mm nominal size) within all leads and lifts as directed by the Engineer in charge .

Providing plinth protection 50mm thick in cement concrete 1:3:6(1 Cement :3 Sand: 6 graded stone aggregate 20mm nominal size) including all leads and lifts complete in all respect.

Providing and fixing brick tiles over mumty roofs grouted with cement mortar 1:3 over a 12mm layer of cement mortar 1:3 and finished neatly ,within all leads and lifts and as directed by the Engineer in charge complete in all respect.

Steel work welded in built up sections, trusses and framed work including cutting, hoisting and fixing in position and applying a priming coat of red paint :-

In R.S joints angles tees etc. upto all leads and lifts complete in all respects.

In grating framed guard bars, ladders railing, brackets and similar works including all leads and lifts complete in all respect,.

Providing and fixing of finalax pipe 40mm dia under floor(for connection cables)including all fitting i.e. elbows,sockets etc.complete in all respect.

Laying and jointing in trenches GMS tube fitting inlet , Outlet, overflow & scoure(light class) (Earth work in trenches to be measured and paid for separately)including all leads and lifts complete in all respect.

40 mm dia. ( light class)

50 mm dia. ( light class)

65 mm dia. ( light class)

80 mm dia. ( light class)

Providing and fixing Gun metel wheel valve ISI marked superior quality including carriage of materials upto all leads and lifts complete in all respects.

50mm dia.

Providing and fixing CI Sluice valve (with hand wheel) as per IS:780- 1984 class -I upto 300mm dia(i/c brass spindle & as per 2906- 1984 class-II for dia > 300mm) complete with bolts, nuts rubber insertion etc. (the tail piece if required shall be measured & paid for separatly)

80mm dia.

Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia. & 180 mm deep(inside) with chained lid RCC top 1:2:4 mix (1 cement :2 sand :4 graded stone aggregate 20 mm nominal size) 100mm thick foundation concrete 1:5:10 mix (1cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1 :3 (1 cement : 3 sand) finished with a floating coat of neat cement i/c curing complete. 600 x 600 x 750 mm inside size With 150 mm thick walls of RCC 1:2 :4 (1 cement :2 sand :4 graded stone aggregate 20mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways including carriage of materials upto all leads and lifts complete in all respects.

Providing and fixing SFRC Man hole cover with frame having frames size of 560 mm internal dia.( Light duty) including carriage of materials upto all leads and lifts complete in all respects.

Manufacturing, supplying & fixing of M.S frame 35x35x5mm with M.S sheet man hole cover 1.66mm thick made of M.S Angle 25x25x5mm with locking arrangement with lock and painting with red oxide complete in all respects as per drawing & design with in all leads & lifts complete & as per the direction of the Engineer-in Charge.

HYDRAULIC ENGINEERING COMPANY

Raman Thakur Govt. Cont.