Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹92.1 CrAccepted-AOC 14 BILASIPARA P O P S BILASIPARA DIST DHUBRI ASSAM PIN 783348 | DHUBRI | ASSAM | 783348 | ₹92.1 Cr | 1 | Accepted-AOC Awarded to substantially responsive bidder |
| Sl No | Description | Qty | Unit | SHREE GAUTAM CONSTRUCTION CO. LTD. L1 |
|---|---|---|---|---|
| 1.01 | Construction of Annex Building of Assam Water Centre under Assam Integrated River Basin Management Program (AIRBMP) Project, adjacent to new ASDMA Headquarters | 1 | Nos | 95,99,21,903.65 ₹96.0 Cr |
Updated dates
Tender Value
₹89.5 Cr
EMD Value
₹1.8 Cr
Closing Date
29 Dec 2025, 2:00 pmClosed
Chief Executive Officer, FREMAA
4th Floor, Assam Water Center Kundil Nagar, Basistha, Guwahati - 781029
Construction of Annex Building of Assam Water Centre under Assam Integrated River Basin Management Program (AIRBMP) Project, adjacent to new ASDMA Headquarters
2025_DoWR_48542_1
FREMAA_CW8_ANNEX BUILDING
Open Tender
Civil Works - Building
540 days
Basistha, near Assam Water Centre, Guwahati
Please refer Tender documents.
5 documents required · 5 mandatory
₹0
₹1.8 Cr
Yes
Basistha, Guwahati, Assam
13 Mar 2026
18 Nov 2025
29 Dec 2025
18 Nov 2025
29 Dec 2025
15 Dec 2025
18 Nov 2025 - 4 Dec 2025
3 Dec 2025
63A TPN MCCB with 5 HP Three phase star delta starter with overload relay and single phase preventer . Each of these compartment shall contain indicating lamp with ON/ OFF/ TRIP status for fan air washer.
BoQ_Ver4.0
Name of the Bidder/ Bidding Firm / Company :
PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)
NUMBER #
SUB HEAD - EARTH WORK
Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5m, as directed by Engineer-in-Charge: All kinds of soil
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. All kinds of soil
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m
Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil.
Supplying chemical emulsion in sealed containers including delivery as specified Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
CONCRETE WORK
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources)
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
R C C WORK
Centring and shuttering including strutting, propping etc. and removal of form for :
Foundations, footings, bases of columns, etc. for mass concrete.
Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
Shelves (Cast in situ)
Lintels, beams, plinth beams, girders, bressumers and cantilevers
Columns, Pillars, Piers, Abutments, Posts and Struts
Stairs, (excluding landings) except spiral-staircases
Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like
Edges of slabs and breaks in floors and walls: Under 20 cm wide
Weather shade, Chajjas, corbels etc., including edges
Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick
Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick
Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landings, beams and balconies (Plan area to be measured)
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections
DESIGN MIX CONCRETE
Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.
Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works upto plinth level
Concrete of M25 grade with minimum cement content of 330 kg /cum
Concrete of M30 grade with minimum cement content of 350 kg /cum
Concrete of M35 grade with minimum cement content of 370 kg /cum
Concrete of M40 grade with minimum cement content of 390 kg/cum
Concrete of M50 grade with minimum cement content of 410 kg/cum
All works above plinth level upto floor V level
Concrete of M25 grade with minimum cement content of 330 kg /cum
Concrete of M30 grade with minimum cement content of 350 kg /cum
Concrete of M35 grade with minimum cement content of 370 kg /cum
Concrete of M40 grade with minimum cement content of 390 kg/cum
Concrete of M50 grade with minimum cement content of 410 kg/cum
Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints. 200 mm wide
Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning/ self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with an universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer's pre-engineered selfcentering arrangement that freely rotates I moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -inCharge. (Material shall conform to ASTM 6063). Floor Joint of 100 mm gap
Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-InCharge. The joints shall be of extruded aluminum base members, self aligning/ centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall conform to ASTM 6063). Wall Joint of 100 mm gap
Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates an universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer's pre-engineered self-centering arrangement that freely rotates I moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall conform to ASTM 6063). Roof Joint of 100 mm gap
BASE ISOLATOR
Design, Manufacture, Supply, Installation & Testing of Lead Rubber Bearings (LRB) in combination with PTFE Slider of approved make for base isolation system of seismic isolator to meet system adequacy requirements based on load combinations as per approved structural design. The base isolation system shall enable the structure to safely displace under seismic loading in all horizontal directions. Bearings shall be manufactured from high-density natural rubber with integral mounting steel plates of desired shape and size, and shall include a lead core of specified diameter as per design. All steel plates shall have a minimum of 3 coats of epoxy paint (total DFT not less than 200 microns) or hot-dip galvanizing as per specifications. Bearings shall support the design vertical load, sustain the maximum design displacement, and absorb earthquake-induced accelerations. Sizes of LRB may vary among manufacturers, however design criteria, performance requirements, and mechanical properties shall conform to structural calculations and relevant standards (AASHTO, EN 15129, ISO 22762, IS 1893, IRC-6 as applicable). Rate shall include : Complete design verification and shop drawing preparation. Factory Type Tests (hysteresis, compression, shear) and Routine / Production Tests (dimensional check, bonding test, material certificates). Third-party witnessing (if specified) and submission of test reports. Supply, packing, transport to site, installation, grouting, alignment, and OEM supervision. All incidental works as per manufacturer’s specifications an
d direction of the Engineer-in-Charge.
The size of the bearing are as per following :
650 mm dia , Axial load capacity 5000 KN
800 mm dia , Axial load capacity 14880 KN
Slider 1 , Axial load capacity 10000 KN
Slider 2 , Axial load capacity 20000 KN
BRICK WORK
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.
Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm/230mm/300 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
STONE WORK
Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)
CLADDING WORK
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby Red
Area of slab upto 0.50 sqm
Area of slab over 0.50 sqm
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF /Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.
WOOD AND PVC WORK
Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).
Supplying, fitting, fixing Stainless Steel fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished ) b) Tower Bolt
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
Supplying, fitting, fixing Stainless Steel fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished )
quality conforming to IS : 2046 Type S including cost of adhesive of approved quality. 1.0 mm thick.
Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.
Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).
Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 -part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover
Providing and fixing ball bearing for rolling shutters.
Extra for providing mechanical device chain and crank operation for operating rolling shutters.
Exceeding 10.00 sqm and upto 16.80 sqm in the area
Exceeding 16.80 sqm in area
Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes
Providing and fixing mild steel round holding down bolts with nuts and washer plates complete
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete
In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
Providing and fixing M.S. tube hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube
Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
FLOORING WORK
62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Dark shade pigment using ordinary cement
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of ce
ment mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
(A) Double charge vitrified tile polished finish of size
ment mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.
Size of Tile 600 x 600 mm
Size of Tile 600 x 1200 mm
(B) Glazed Vitrified tiles Matt/Antiskid finish of size
Providing and fixing removable raised/ false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame workmand G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100 mm x 100mm x 3 mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16 mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80 mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip non-combustible Portland cementitious core mixed with light weight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm. The panel is to withstand a Concentrated Load of 363 kgs applied on area 25 mm x 25 mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product.
450 mm Finished Floor Height (FFH).
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Polished Granite stone slab colour of Black, Cherry/Ruby Red
Broken China Ceramic Flooring:- Providing and laying flooring/dado/skirting with broken glazed China ceramic tiles of approved colour and shade, set over 20 mm thick cement mortar bed in 1:4 (1 cement : 4 coarse sand), joints filled with white cement mixed with matching pigments to give an even shade, rubbing, polishing and finishing complete as per direction of Engineer-in-Charge.
FLOCKED Textile Carpet Flooring: - "Providing & Fixing of Flocked textile floor of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of 4.3 mm and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, anti-microbial treatment, with resilient waterproof backing, anti allergic which is certified by British allergy foundation. The carpet should have permanent static contro. The work should be carried out by the authorized installer of the Company in India. Carpet should be laid on zero leveled surface. Carpet should be stick with SR 998 on the floor.
SPC Flooring:- Providing and laying Stone Plastic Composite (SPC) Flooring of thickness 4 mm (minimum) having wear layer of not less than 0.5 mm, density not less than 2000 kg/m³, abrasion resistance AC3/AC4 grade, slip resistance R9 minimum, fire rating class Bfl-S1, formaldehyde emission E1 grade, and water absorption less than 0.1%. The flooring shall be multi-layered comprising UV coating, wear layer, decorative film, SPC rigid core (limestone + PVC composite) and IXPE/EVA underlayment (where specified). Tiles/Planks shall be of approved shade, finish and size (minimum 600×600 mm for tiles or 1220×180 mm for planks), laid over a clean and level sub-base using click-lock system / adhesive as per manufacturer’s specification, including necessary expansion ga
ps, complete in all respects as directed by Engineer-in-Charge.
PU (Polyurethane Resin) Flooring:- Supplying and laying of chemical resistant, antimicrobial, Polygiene® HACCP International Certified 4mm thick Polyurethane resin heavy duty flooring in approved colour having temperature resistance of 90˚C at 4mm thickness and chemical resistance properties, trowel applied smooth matt coloured finish, Microbial/fungal resistant incorporates Polygiene a performance based antimicrobial additive which inhibits the growth of bacteria, fungi, moulds and mildew. Non-tainting and non-dusting, over the scratch coat of Pu concrete the scratch coat cured system shall exhibit the following properties: Fire Resistance BS476:Part 7 ,Surface Spread of Flame: Class 2 (indicative),Slip Resistance TRRL Pendulum Slip Test Dry 70 Wet 25Impact Resistance BS8204 Part1 Cat: A (<0.5mm),Coefficient of Thermal Expansion ASTM C531: 5.70 x 10-5 oC-1Water Permeability Nil–Karsten test (impermeable)Vapour Permeability ASTM E96:905g/m/24hrs (at 4mm thick),Abrasion Resistance Taber Abrader: 0.1g loss per 1000 cycles (1kg load using CS17 wheels)Compressive Strength >55 N/mm2 (BS6319)Flexural Strength >20 N/mm2 (BS6319)Tensile Strength >12 N/mm2 (BS6319) Bond Strength Greater than cohesive strength of 25N/mm2 concrete. >1.5 MPa. Substrate requirement of Concrete or screed substrate should be a minimum of 25N/ mm2, free from laitance, dust and other contamination grinding/scarifying . The substrate should be surface dry and free from rising damp and ground water pressure. Providing line marker ( upto 100mm wide ) in approved colour and coving of 50mm X 50mm using Epoxy resin based coving mortar at all the wall to floor junction as per approved shop drawing and direction of engineer in charge.
ROOFING WORK
Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick
(minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.
Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening“for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint,for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.
Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointingcompounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.
GYPSUM FRMR Board False ceiling:- Providing and fixing Fire, Moisture & Rodent Resistant (FRMR) Gypsum Board False Ceiling of 12.5 mm / 15 mm thick FRMR gypsum board conforming to IS: 2095 (Part I & III) and ASTM C 1396, including providing and fixing G.I. framework made
of perimeter channels 20 x 27 x 0.5 mm, intermediate channels 45 x 15 x 0.9 mm and ceiling sections 80 x 26 x 0.5 mm (all galvanized with zinc coating 120 gsm as per IS: 277) suspended from the soffit with G.I. cleats, anchor fasteners and suspension rods at required spacing, and fixing the gypsum boards with 25 mm long drywall screws at 230 mm c/c, including jointing and finishing with jointing compound, jointing tape in three layers, sanding to smooth finish, making necessary cut-outs for light fittings, diffusers, grilles, sprinklers, etc. (but excluding the cost of fittings), all complete as per drawing, specification and direction of the Engineer-in-Charge.
Acoustic Ceiling:- Providing & fixing Compressed Polyester fibre acoustical panels, 9 mm thick acoustic polyester fibre pad pasted on 16 mm thick perforated wooden panels by rubber based adhesive for rigid fixation. The Polyester fibre acoustic panels to be backed with black acoustic fleece. Total thickness of the Composite Acoustic panel will be 25 mm. All joints of Polyester fibre acoustic panel should have dowel connection to avoid any sagging /unevenness. All Polyester fibre acoustic panels should be should be fixed on GI ‘Z’ clamp made out of 1 mm thick GI sheet of size 30 mm x 30 mm collar and 50 mm high to match with the installed GI frame. The edges of the polyester fibre pad to be taper cut by special purpose machine to produce a ‘V’ joint at all four ends. The Polyester fibre acoustic panel of size 600 mm x 600 mm / 600 x 1200 mm, with a perforated pattern of dia. 08/10 mm or as per acoustic design / Architects approval for better absorption. The polyester fibre to be chemically treated for fire retardancy. GI perimeter channels of size 0.5mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending GI intermediate channels of size 45mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angles of width 25mm x 10mm x 0.5mm thick fixed to soffit with GI cleats and steel expansion fasteners. Ceiling section of 0.5mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in a direction perpendicular to the intermediate channel at 457mm c/c. 25mm tapered egde (confirming to IS: 2095-1996: Part-I) is then screw fixed to ceiling section with 25mm drywall screws at 230mm c/c. Screw fixing is done mechanically with drilling machine with suitable attachment complete in all respect as per drawing and direction of Engineer-in-Charge.
Aluminium Baffal Ceiling Providing and fixing wooden finish U Baffle Aluminium panel ceiling of different colours and finish supplied by approved manufacturers, consisting of panel size 50 mm width X 100 mm deep using 0.6 mm thick, panel length upto 4 mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance Aluminium alloy AA 3005 (Al. Mg) for higher strength and good roll forming characteristics. Aluminium panels shall be chromatised for maximum bond between metal and paint enamelled twice under high temperature, Exposed side with a full primer and finish coat on a Continuous Paint Line. Panels shall be clipped to a baked enamelled Aluminium carrier of 30 mm wide x 47 mm high x 0.5 mm thick, Black Colour coated, one leg of the carriers with cut outs to hold the panels in a module of 150 mm. Panel carrier shall be suspended by means of threaded rod at a distance of 1.8 mtr c/c. Actual distance of threaded rod/carrier might vary and to be calculated based on the actual drawing and site condition. The measurements shall be wall to wall without any deductions for lights, diffuses, columns etc. Ceiling area above U Baffle should be painted in black colour or any other colour as per the architect for better aesthetics before fixing this system.
Aluminium Metal False Ceiling 300 x 1200 Perforated Aluminium clipin perforated metal ceiling system consisiting of 300 x 1200mm clipin tile of powder coated Aluminium in 0.7mm thickness with beveled edge in white colour 60 microns powder coating with standard perforataion of 1.8mm dia. The back of the tile should have black accoustical fleece. The NRC should be 0.50. Installation: To comprise 3000mm long ‘C’ channels spaced at 1200mm centres securely fixed to the structural soffit by support clamp & approved hangers. The last hanger at the end of each C channel should not be greater than 600mm from the adjacent wall.providing and fixing ‘L’ wall angle of size 19x19mm mm made of 0.4 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm centre to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.5 mm thick from the soffit with help of soffit cleat 30x25x1.4 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier
FINISHING WORK
12 mm cement plaster of mix : 1:6 (1 cement : 6 fine sand)
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement : 6 fine sand)
18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) and a top layer 6mm thick cement plaster 1:3 (1 cement: 3 coarse sand) finished rough with sponge.
6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)
Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.
per bag of 50kg cement used in the mix
Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.
Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre
Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
Finishing walls with Acrylic Smooth exterior paint of required shade : Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm.
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats
Dry Wall Partition Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12 mm thick Ply board + 6 mm ply+1 mm thick laminated sheet.
Acoustical wall Panelling (Wooden Fabric):- Providing & fixing Compressed Polyester fibre acoustical panels, 9 mm thick acoustic polyester fibre pad pasted on 16 mm thick perforated wooden panels by rubber based adhesive for rigid fixation. The Polyester fibre acoustic panels to be backed with black acoustic fleece. Total thickness of the Composite Acoustic panel will be 25 mm. All joints of Polyester fibre acoustic panel should have dowel connection to avoid any sagging /unevenness. All Polyester fibre acoustic panels should be should be fixed on GI ‘Z’ clamp made out of 1 mm thick GI sheet of size 30 mm x 30 mm collar and 50 mm high to match with the installed GI frame. The edges of the polyester fibre pad to be taper cut by special purpose ma
chine to produce a ‘V’ joint at all four ends. The Polyester fibre acoustic panel of size 600 mm x 600 mm / 600 x 1200 mm, with a perforated pattern of dia. 08/10 mm or as per approved acoustic design for better absorption. The polyester fibre to be chemically treated for fire retardancy as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-( latest edition at the time of execution ) for excellent results. The system will be installed with a 42 mm thick acoustic backing of Tissue fibre paper laminated Rockwool density 64 kg/cum, confirming to IS 8183 ( latest edition at the time of execution ) to achieve 0.9 NRC value. GI Frame consisting of 0.5mm thick GI channel of size 50 x 38 mm, fixed horizontally alongwith wall and between vertical columns at locations . Gap between two horizontal channels should be 600mm c/c. G.I Channel to be fixed firmly with approx. size fasteners to hold the weight of wall frame & wall panels properly Complete with all accessories as required at sitein all respects as per approved shop drawing, manufacturers specifications & directions of Engineer-in-Charge . All makes and models of items/samples shall be approved by the Engineer-in-Charge prior to the installation.
Luster Paint:- Providing and applying Luster Paint of approved brand and shade on wall surface, after preparing the base with wall putty/POP, primer, and undercoat as per manufacturer’s specifications. Application shall be in two or more coats by brush/roller/spray to achieve uniform shade and finish, complete in all respects as directed by Engineer-in-Charge.
DISMANTLING AND DEMOLISHING WORK
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
ROAD WORK
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres
Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).
Supplying and stacking at site.
90 mm to 45 mm size stone aggregate
63 mm to 45 mm size stone aggregate
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30
Supply, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.
Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. With granite stone of all colour except black, cherry/ruby red of area less than 0.50 sqm.
60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.
80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.
PILE WORK
Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) : 750 mm dia piles
Empty boring for specified diameter piles from ground level to cut-off level. h) Pile Dia. 750 mm
Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. Single pile above 50 tonne and upto 100 tonne Safe capacity
Initial test (Test Load 2.5 times the Safe capacity) Initial test – minimum 1.5% of total pile per building
Routine test (Test Load 1.5 times the Safe capacity) Routine test 1.5% of the total number of piles in each Block. However, locations of test piles shall be decided by the Client
ALUMINIUM WORK
Casement Aluminium Door Frames – Single Rebate Doors Providing and Fixing of
Door Frames made of A2Z series High-performance prefabricated factory-made system Aluminium with powder coating of 60-70 microns. Section for frame should be of 101.60mm x 44.45mm with rebate of 44mm for shutter with wall thickness of 4mm thick. All frame corners shall be joined/assembled using self-locating corner cleats (No screwing at corners shall be allowed). 4 Nos Hinges will be there for shutters. (Make: A2Z Infra Solutions/Lilli Windows/Reyners/BWS Windows)
Casement Aluminium Door Frames – Single Rebate Doors Providing and Fixing of Door Frames made of A2Z series High-performance prefabricated factory-made system Aluminium with powder coating of 60-70 microns. Section for frame should be of 100mm x 45mm with rebate of 40mm for shutter with wall thickness of 3mm thick. All frame corners shall be joined/assembled using self-locating corner cleats (No screwing at corners shall be allowed). 4 Nos Hinges will be there for shutters. (Make: A2Z Infra Solutions/Lilli Windows/Reyners/BWS Windows)
For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)
Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness
Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
Casement Aluminium Doors – Single Rebate Doors Providing and Fixing of Doors made of A2Z series High performance prefabricated factory made system Aluminium with powder coating of 60-70 microns. Section for outer frame should be of 73.2mm x 50mm, section for glass shutter for door should be of 92.5mm x 58mm. All frame corners shall be joined/assembled using self-locating corner cleats (No screwing at corners shall be allowed). Double glazed hermetically sealed glazing in aluminium doors should be provided with 5mm toughened glass on both the sides, having 10mm airgap including EPDM gasket, perforated aluminium spacers, desiccants, sealant, etc. Weather silicon sealant of reputed make to be used to make glazing watertight. The system should be tested for Air tightness, water penetration as per standards. Multi point locking system along with hardware of reputed make including hinges for all the door shutters, complete for finished item of work. (Make: A2Z Infra Solutions/Lilli Windows/Reyners/BWS Windows)
Providing and Fixing of ventilators made of A2Z series High performance prefabricated factory made system Aluminium with powder coating of 60-70 microns. Section for outer frame should be of 40mm x 39mm, section for glass shutter and mullion should be of 54mm x 40mm. All frame corners shall be joined/assembled using self-locating corner cleats (No screwing at corners shall be allowed). Double glazed hermetically sealed glazing in aluminium doors should be provided with 5mm toughened glass on both the sides, having 10mm airgap including EPDM gasket, perforated aluminium spacers, desiccants, sealant, etc. Weather silicon sealant of reputed make to be used to make glazing watertight. The system should be tested for Air tightness, water penetration as per standards. Single point locking system along with hardware of Hivik/Pego make including hinges for all the shutters, complete for finished item of work. (Make: A2Z Infra Solutions/Lilli Windows/Reyners/BWS Windows)
System Aluminium Factory made Double Rebate Windows with Grill and Mesh Providing and fixing of A2Z Series Double rebate windows & ventilators made of High-performance factory-made system Aluminium windows with powder coating of 60-70 microns. Section for Outer frame should be of 139.80mm x 27.99mm, Glass shutter frame shall be of 75mm x 52mm, Mesh shutter frame shall be of 71mm x 30mm, Mullion size 139.80mm x 67mm, Double Glazed beading shall be of 20mm x 25mm. 24mm DGU (Double Glazed Unit) of 6mm Solar Glass + 12mm Airgap + 6mm Solar Glass shall be used in all the windows & ventilators. Stainless Steel Wire Mesh shall be used in Wire mesh Shutters. 10mm Sq bar M.S. Grill/Guard bar with 125mm c/c shall be fixed in between glass & mesh shutter. All frame corners shall be joined/assembled using self-locating corner cleats (No screwing at corners shall be allowed). All Hardware shall be used from a reputed brand, weather silicon shall be used for filling the gap between window opening & window Frame complete in all respect including all taxes. (Make: A2Z Infra Solutions/Lilli Windows/Reyners/BWS Windows)
Design, Supply, fixing, coordinating Automatic sliding door operator/Mechanism/Driver to hold 12 mm Toughened glass of approved make, Microprocessor control panel with adjustable parameters for opening and closing speed, self-learning, reversing when obstruction is encountered, hold open time and opening and closing force. Clause of protection IP 20, The system
WATER PROOFING WORK
(A) FOUNDATION & STITCH SLAB WATER PROOFING
Providing and applying waterproofing treatment for 'Raft Slab' by using 1.2mm thick HDPE fully bonded sheet membrane complying to BS8102:2009. The HDPE shall be virgin HDPE & not recycled, thickness of bare HDPE shall not be less than 0.8 mm coated with pressure sensitive adhesive layer and a trafficable granular top layer. The HDPE membrane shall have the following typical properties: 1. Tensile Strength : >25 Mpa ( as per ASTM D412) 2. Puncture Resistance: >1000N±5% (as per ASTM E154) 3. Elongation: >500% 4. Peel adhesion to concrete: >880N/m (as per ASTM D903 Modified) 5. Resistance to Hydrostatic Head: >70 mtr (as per ASTM D751-06(2011) 6. UV exposure test (60 days): No change 7. Lap Joint Strength : 1500N/m (as per ASTM D1876). HDPE membrane shall be installed over the entire PCC area with standard 75 mm selvedge laps and end laps overlaid with membrane HDPE Sealed Tape as per manufacturer's instructions. The rates are inclusive of necessary surface preparation required to lay the membrane and installation of membrane as per manufacturer methodology approved by client. Hot applied materials or protective screed shall NOT be permitted. The HDPE membrane shall be approved from a third party lab certifying the above mentioned properties.
(B) RETAINING WALL WATER PROOFING
Providing and applying waterproofing treatment using hybrid polyuria/polyurethane system. Polyuria will be hybrid polyuria/polyurethane, rapid curing and highly resilient fully bonded cured to membrane having a mixed density of 1.02g/l. Minimum recommended coverage rate is 1.5ltr/sqmtr in 2 coats to achieve a total DFT of 1.5mm. The cured membrane shall exhibit: 1) Tensile strength ASTM D412 : >13 MPa 2) Shore A Hardness: 80 3) Elongation ASTM D412 : >450% 4) Abrasion( 1kg, CS 10 wheels, ASTM D 4060): 1.3 mg/1000 cycles 5) Service temperature: -20⁰C to +80⁰C 6) Resistant to Fire (EN13501-1)-Class E,d0 7) Crack bridging not less than 3mm. 8) Manufacturers shall provide Certificate for Zero VOC, resistance to fire, 25 years life expectancy test certificate. It must be applied utilizing plural heated high-pressure spray proportioning machine/spray gun such as those manufactured by WIVA/Graco or equivalent spray proportioning equipment. It must be applied utilizing plural heated high-pressure spray proportioning machine/spray gun such as those manufactured by WIVA/Graco or equivalent spray proportioning equipment. Well cleaned, levelled, & well dry concrete surface shall be primed with Nitoprime 31, applied at consumption of 250gms/Sqm, followed by application of Polyuria, using spray machine applied at consumption of 1.5litres/Sqm in two coats for 1.5mm DFT . Coating shall be applied from parapet to parapet and to be terminated at least 300mm above FFL or as per site conditions. Termination: Termination shall be done by providing a groove cut of 6mm x 6mm and later sealing the same with Nitoseal PU40, all complete as per manufacturer methodology. System includes surface preparation using surface grinder or suitable means to receive w.p coating, making of coving using Nitobond SBR admixed PMM at all wall-floor corners, application and termination all complete as per manufacturer's specification and methodology.
Construction joints (During casting of Retaining Wall): Supplying and installing a high performance synthetic hydrophilic elastomeric water stop of 25mm x 10mm. The water stop shall have an unrestrained volumetric expansion of upto a maximum of 200% and must be able to withstand a hydrostatic head of 100 meters (10 bar). The water bar shall have BBA certification. The water stop shall be used at locations such as : (i) starter joint: Junction of raft and retaining wall. (ii) At all other locations like construction joints as shown in the drawings and installed in accordance with manufacturer's recommendations.
Tie rod holes treatment: Removing all loose particles and dust from hole, cleaning it with compressed air and bring hole to SSD condition before treating hole with polymer modified mortars like Renderoc HSxtra or approved equivalent and cure it with water based curing compound. In case of pvc sleeves, sleeves shall first be removed, prior to treating with Renderoc HSXtra or approved equivalent. For Holes, where rebar is used as tie bar, the same shall be at least 25mm deep from the surface & later the hole should be fixed with polymer modified mortar.
Casement Aluminium Doors – Single Rebate Doors Providing and Fixing of Doors made of A2Z series High performance prefabricated factory made system Aluminium with powder coating of 60-70 microns. Section for outer frame should be of 73.2mm x 50mm, section for glass shutter for door should be of 92.5mm x 58mm. All frame corners shall be joined/assembled using self-locating corner cleats (No screwing at corners shall be allowed). Double glazed hermetically sealed glazing in aluminium doors should be provided with 5mm toughened glass on both the sides, having 10mm airgap including EPDM gasket, perforated aluminium spacers, desiccants, sealant, etc. Weather silicon sealant of reputed make to be used to make glazing watertight. The system should be tested for Air tightness, water penetration as per standards. Multi point locking system along with hardware of reputed make including hinges for all the door shutters, complete for finished item of work. (Make: A2Z Infra Solutions/Lilli Windows/Reyners/BWS Windows)
Construction Joint & Crack Treatment: Chase open construction joints in v shape of 15mm x 15mm using suitable means, later cleaning the same using water jet and applying a bond coat of Nitobond SBR or approved equivalent mixed with cement and water in a ratio of 1:1:3(Water : Polymer : Cement), followed by filling of Nitobond SBR admixed PM
Design, Supply, fixing, coordinating Automatic sliding door operator/Mechanism/Driver to hold 12 mm Toughened glass of approved make, Microprocessor control panel with adjustable parameters for opening and closing speed, self-learning, reversing when obstruction is encountered, hold open time and opening and closing force. Clause of protection IP 20, The system
M or approved equivalent in the groove, including, filling, finishing, curing all complete as per the direction of Engineer In-Charge. In case of structural cracks, injection grouting shall be carried out either using Cementitious Grout or Low viscous epoxy grout, depending upon the kind of cracks.
Injection Nozzle Packing: Drilling and fixing injection packers in RCC members for cementitious grouting, drilling holes in structural members at the intervals as per recommendations/ requirements, cleaning the holes by air blower prior to fixing nozzles. Insert 12 mm dia, 50-75 mm long PVC or equivalent injection packers in cleaned holes with fast setting mortar like Renderoc Plug or equivalent. Cut the packers by cut of wheel after completion of grouting without damaging structural elements and later filling the same using Nitobond SBR Latex admixed PMM or approved equivalent.
Injection Grouting: Supplying & applying plasticised expanding grout admixture cementitious grouts of approved make having Chloride content - Nil as per BS:5075 , Typical unrestrained expansion of upto 4% in general. The admixture should be mixed @ 225 gms per 50kg of cement, as per manufacturers specification and as directed. The cost is inclusive of providing and fixing of nozzles and grout (including cement) consumed.
Protection: Supplying and applying 10mm thick dimple board for protection as per manufacturer's recommendation followed by backfilling. Backfilling should be done in stages and shall be free from any rock/stone/brick/metal to avoid any damage to the waterproofing and drain board.
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying a) First layer of slurry of cement @ 0.488 kg/sum mixed with water proofing cement compound @ 0.253 kg/sum. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sum mixed with water proofing cement compound @ 0.126 kg/sum. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge :
With average thickness of 120 mm and minimum thickness at khurra as 65 mm
TANKS WATER PROOFING Protection coating internal - STP
Providing, mixing and applying Thixotropic pitch membrane of approved make by brush or spray to give uniform finish. The material should be a high build, pitch extended epoxy amine adduct, two pack system, specifically designed to provide a tough, impermeable and corrosion resistant film. Minimum mixed volume solid content is 65% and material shall be applied @ coverage rate of 1.5 m2/lit (including wastage)in two coats to achieve a total DFT of 350 Microns. By virtue of two component faster rates of application are possible using airless spray equipment maintaining minimum nozzle pressure of 140 bar with an orifice size of 0.65 - 0.79mm is suitable for application. Up to 5% by volume Nitoflor Sol may be added to ease spray application. system includes surface preparation and application as per approved methodology.
Providing, mixing and applying approved make epoxy coating and applied by authorised applicator. Approved epoxy coating should be 100% (volume of solids) solvent free epoxy resin system designed for potable water retaining structures. Minimum recommended rate of application is 0.25-0.30 lit/Sqm to achieve a total DFT of 200 microns. Product shall be CFTRI approved and cured film shall comply with the requirements of IS: 9833 - 1981. system includes surface preparation and application as per approved methodology.
Surface Preparation: RCC Surfaces must be clean, even and sound concrete. Remove all oil, dirt, laitance, protrusions(by light grinding) and other contaminants manually to attain a fairly smooth surface.
Coving: Coving at the junction of Horizontal and vertical offsets with CM 1:4 mixed with Nitobond SBR at the dosage of 10% by weight of cement.
STRUCTURAL GLAZING AND ALUMINIUM COMPOSITE PANEL
Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.
Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:
Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.123) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) p
rovided and fixed in position, shall be measured in sqm.
(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.
Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.
Providing and Fixing – Clay Façade Panelling system in approved shade, finish, size and in thickness of 15mm. The clay panels shall have Flexural Strength /Modulus of rupture ≥ 9 N /mm2 in accordance to ISO – 10545 ‐4 with breaking strength ≥ 550 N in accordance to ISO 10545‐4. The panels should have water absorption ≤ 4 % in accordance to ISO – 10545‐3. The surface scratch hardness value i.e., Moh’s scale should be Minimum 6 in accordance to ISO ‐10545‐2. The clay panels should have inherent properties of being resistant to stains and chemicals. The material should be Class I material in terms of reaction to fire in accordance to EN 13501‐1 / ASTM E136. The entire system should be certified by an approved third‐party structural consultant for a minimum structural proof load test with positive & negative wind pressure of 5kPA. The cladding panels shall be fixed on to existing cured plastered surface substrate wall treated with one or two coats of primer with appropriate Aluminium rectangular hollow section vertical members framework of 25mm X 50mm (2mm thick) which shall be spaced out in accordance to the dimensions of the panel with minimum spacing of 600mm. The framework shall be attached through L shaped aluminium connectors of 25mm X 37mm (2mm thick) to the substrate walls. The manufactured panels shall have an evenly controlled factory – made groove for resting on to a continuous aluminium rail profiles throughout their length. The profiles are designed and manufactured for starter piece, intermediate and an inverted starter profile for the top piece. Aluminium rail profile shall ensure uniform and precision joints and shall be factory finished with Super Durable powered coated colour in approved RAL shade. All fixtures, and screws shall be corrosion free i.e., all rail profiles, cleats to be used should be made of 6063 T6 alloy grade and all screws used should be of Zinc Plated of M/s Hilti, Worth, Klimas, Patta or equivalent. The groove of the width can be chosen i.e., 1.7mm, 3mm, 6.5mm, 12.6mm or 20mm. The corners junctions to be neatly treated with adequate aluminium closed ‘L’ corner shaped pieces in required length in similar shade coated with factory finished Super Durable Powder, to the clay façade panel. Alternatively, the corners junctions can be treated as regular corner fixing or Mitred corner fixing. All fixing details and drawings to be provided by vendor and to be duly approved by Engineer in charge at project and the work to be carried out as per direction of the Engineer‐ in charge.
New Technologies and Materials
Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
Frame size 50 x 100 mm
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick
Horticulture Work
Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
Supplying and stacking sludge at site including royalty and carriage up to 5 km (sludge measured in stacks will be reduced by 8% for payment).
Supplying and stacking at site dump manure from
approved source, including carriage up to 5 km Complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20mm
Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
Providing and fixing M. S. tree guard 50 cm square in plan, height 1.40 metre above ground level and 0.50 metre below ground level. The vertical members shall consist of four nos of angle iron of size 25x25x5 mm 1.9 long, one at each corner and 8 nos flat iron of size 25x5 mm 1.4 long. The vertical members shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground , including refilling the earth, compaction etc. complete. The tree guard shall be painted with two coats of paint of approved brand and manufacture over a coat of primer, complete in all respect.
Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light, watering with sprinkler and maintenance for 30 days or more till the grass establish properly as per direction of officer-in-charge.
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)
Trees Plant
Shrubs Plant
Hedge Plant
Providing and stacking of Alstonia scholaris of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Cassia javanica of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Erythrina indica of height 150-165 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Lagerstroemia thorelli of height 150-165 cm. in poly bag of size 25 cm as per direction of the officer-in-charge
Providing and stacking of Nauclea cadamba (Kadam) of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Peltophorum species of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.
Providing and stacking of Pongamia glabra (Papri) of height 120-135 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Spathodea campanulata of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Terminalia arjuna of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.
Providing, stacking and Displaying Areca Palm having ht. 1.20 m to 1.50 m with 5 to 6 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot and as per direction of the officer-in-charge
Providing and stacking of Foxtail palm ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bag as per direction of the officer-in-charge.
Providing, stacking and Displaying Rhapis Palm having ht. 45 cm to 60 cm with 5 to 7 suckers, well developed, full of fresh and healthy leaves in 25 cm size of Earthen pot / Plastic pot and as per direction of the officer-in-charge.
Providing and stacking Clerodendrum inerme having ht. 25 cm to 30 cm multi branched in 25 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.
Providing and stacking Duranta Golden, having ht. 15 cm to 20 cm bushy shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.
Providing and stacking Euphorbia milli hybrid variety, having ht.30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 20 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-incharge.
Providing and Stacking of Minia erecta plant of height 45 cm to 60 cm multi branches well developed in poly bag of size 20 cm as per direction of the officer-in-charge.
Providing and stacking Portulacaria afra (Jade plant ) with 5 to 6 branches in 20 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.
Providing and stacking Cuphea chinensis of ht. 20 cm to 30 cm full of branches and healthy foliage in 15 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.
Providing, stacking and Displaying Ruellia dwarf of different colour well developed with fresh & healthy foliage with bloom in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.
Providing, stacking and Displaying Zephyranthes sp. (Rain lily) having 8 to 10 plants with bloom, in fresh & healthy foliage well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
Transplantation of Trees Transplantation of trees with in a distance of 2km including excavation around existing tree, pruning of branches, lifting, loading and transportation of existing tree, digging pits for placing tree at new place, adding manure, sand, fertilizer, hormones and bio fertilizer to it. Levelled and neatly dressed and disposal of surplus materials from old existing and new sites to designated place. Each tree should be firmly secured to the stake so as to prevent excessive movement, flooding with water, treatment of roots, rope and gunny bags as per direction of the officer incharge. T&P and all required materials shall be arranged by the contractor and nothing extra shall be paid on this account. (a) Girth of tree shall be measured at a height of 1m above ground level.
Girth of trees upto 50cm.
Girth of trees beyond 50cm and upto 90cm.
Girth of trees beyond 90cm and upto 150cm.
Girth of trees beyond 150cm.
PLUMBING WORK
SANITARY INSTALLATIONS
Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
Supply, Receiving, Storing & Fixing of vitreous China Sanitary fixturs and CP fitting and other accessaries for Handicapped toilet Hindware Cat no. 70002 (Matrix Set-1). Each Matrix Set shall comprised (Wash Basin 65 x 35 with one pair mounting brackets, EWC & Cistern complete with fittings & seat cover, one no hinged ra
il 76 cm and five nos of grab rails 60 cm). complete all respect.
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern
Providing and Fixings stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. White Agaria Marble Stone
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer
Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: White glazed fire clay kitchen sink of size 600x450x 250 mm
Supply, Receiving, Storing & Fixing of CP brass wall mounted sink mixer with C.P. wall flange, swinging spout complete as required with flow rate of 6.0 LPM complying to Green Building requirements.
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
Semi rigid pipe 40 mm dia
Flexible Pipe 40 mm dia
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Providing and fixing toilet paper holder : C.P. brass
Supplying, Installation, Testing and Commissioning of surface mounted satin-finish type 304 stainless steel jumbo roll toilet tissue dispenser complete.
Providing, fixing, Testing and Commissioning of CP brass two way bib cock with wall flange including, necessary flange, cutting and making good he walls / floors wherever required complete.
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Supplying, Installation, Testing and Commissioning bright polish stainless steel surface mounted coat hooks complete.
Supplying, Installation, Testing and Commissioning of Towel Ring fixed with CP brass screw complete.
Supplying, Installation, Testing and Commissioning of Soap Dish fixed with CP brass screw complete.
Providing, fixing, Testing and Commissioning surface mounted soap dispenser with horizantal tank , corriosion resistant valve dispense and 1.2 litre capacity soap refill window including cutting and making good the wall wherever required.
Providing, fixing, Testing and Commissioning of CP brass two way bib cock with wall flange including, necessary flange, cutting and making good he walls / floors wherever required complete.
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Supplying, Installation, Testing and Commissioning of Stainless Steel body tissure paper dispenser complete.
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore
Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge.
AIR VALVE & WATER METER (BULK TYPE)
Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :
50 mm dia
80 mm dia
100 mm dia
Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :
80 mm dia nominal bore
100 mm dia nominal bore
Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 :
Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 15 mm nominal bore
Providing, fixing, Testing and Commissioning automatic Aerosol Dispenser with wooden cleats and C.P. brass screws including cutting and making good the wall wherever required.
Supplying, Installation, Testing and Commissioning of Drinking Water station with wall mounted RO unit ( 100 LPH) capacity with water cooler of 80 ltr/hr. cooling capacity and 120 ltr storage capacity & ss storage tank made of pure Stainless steel body, without rusting , without corrosion. including externallly mounted thermostat to make it easy to set water temperature, wth extra large SS wate tray prevent spalashing and ensures fast drainage of water , auto cut facilitie , over load compressor protection, electricl supply internal wiring etc. to complete the work.
Providing and fixing in position storage type automatic electric water heater pressure / non pressure type thermostatically controlled, single phase, vertical wall mounted of with thermostats, inner container of stainless steel complete with 1 Mtr three core flexible cord with plug, non-return valve and pressure release valve complete including fixing and testing complete in all respect (to the approval of Engineer-In-Charge). 25 ltrs.
INTERNAL WATER SUPPLY
Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Exposed on wall
15 mm outer dia pipe
22 mm outer dia pipe
28 mm outer dia pipe
35 mm outer dia pipe
42 mm outer dia pipe
54 mm outer dia pipe
65 mm dia
80 mm dia
Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps at 1.00m spacing and also including cutting of chases and making good the walls including testing of joints complete as per direction of Engineer -in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Concealed Pipe
18.86A.1 15.88 mm outer dia Pipe.
18.86A.2 22.22 mm Outer dia pipe
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards
with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Coupling/Socket
For 15 mm outer dia pipe
For 22 mm outer dia pipe
For 28 mm outer dia pipe
For 35 mm outer dia pipe
INTERNAL WATER SUPPLY
Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Exposed on wall
15 mm outer dia pipe
22 mm outer dia pipe
28 mm outer dia pipe
35 mm outer dia pipe
For 42 mm outer dia pipe
INTERNAL WATER SUPPLY
Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Exposed on wall
15 mm outer dia pipe
22 mm outer dia pipe
28 mm outer dia pipe
35 mm outer dia pipe
For 54 mm outer dia pipe
INTERNAL WATER SUPPLY
Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Exposed on wall
15 mm outer dia pipe
22 mm outer dia pipe
28 mm outer dia pipe
35 mm outer dia pipe
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Reducer
54 mm outer dia pipe
65 mm dia
80 mm dia
For 22 mm x 15 mm outer dia pipe
Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps at 1.00m spacing and also including cutting of chases and making good the walls including testing of joints complete as per direction of Engineer -in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Concealed Pipe
18.86A.1 15.88 mm outer dia Pipe.
18.86A.2 22.22 mm Outer dia pipe
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards
with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Coupling/Socket
For 28 mm x 15 mm outer dia pipe
For 15 mm outer dia pipe
For 22 mm outer dia pipe
For 28 mm outer dia pipe
For 28 mm x 22 mm outer dia pipe
For 35 mm x 22 mm outer dia pipe
For 35 mm x 28 mm outer dia pipe
For 42 mm x 22 mm outer dia pipe
For 42 mm x 28 mm outer dia pipe
For 42 mm x 35 mm outer dia pipe
For 54 mm x 28 mm outer dia pipe
For 54 mm x 35 mm outer dia pipe
For 54 mm x 42 mm outer dia pipe
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Sleeve/Slip Coupling/ Socket
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge.. Elbow 90°
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Equal Tee
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Reducing Tee
For 35 mm x 22 mm outer dia pipe
For 35 mm x 28 mm outer dia pipe
For 42 mm x 22 mm outer dia pipe
For 54 mm x 28 mm outer dia pipe
For 54 mm x 42 mm outer dia pipe
For 35 mm x 15 mm outer dia pipe
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Equal Tee
For 54 mm x 22 mm outer dia pipe
For 35 mm x 22 mm outer dia pipe
For 35 mm x 28 mm outer dia pipe
For 42 mm x 22 mm outer dia pipe
For 54 mm x 28 mm outer dia pipe
For 54 mm x 42 mm outer dia pipe
For 35 mm x 15 mm outer dia pipe
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Equal Tee
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Female Thread Tee
INTERNAL WATER SUPPLY
Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Exposed on wall
15 mm outer dia pipe
22 mm outer dia pipe
28 mm outer dia pipe
35 mm outer dia pipe
For 15 mm outer dia x 1/2” nominal dia threaded
INTERNAL WATER SUPPLY
Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Exposed on wall
15 mm outer dia pipe
For 22 mm outer dia x 1/2” nominal dia threaded
For 35 mm x 22 mm outer dia pipe
For 35 mm x 28 mm outer dia pipe
For 42 mm x 22 mm outer dia pipe
For 54 mm x 28 mm outer dia pipe
For 54 mm x 42 mm outer dia pipe
For 35 mm x 15 mm outer dia pipe
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Equal Tee
For 22 mm outer dia x 3/4” nominal dia threaded
For 42 mm x 22 mm outer dia pipe
For 54 mm x 28 mm outer dia pipe
For 28 mm outer dia x 1/2” nominal dia threaded
For 35 mm x 22 mm outer dia pipe
For 35 mm x 28 mm outer dia pipe
For 42 mm x 22 mm outer dia pipe
For 28 mm outer dia x 1” nominal dia threaded
For 35 mm outer dia x 1/2” nominal dia threaded
Supplying, Installation, Testing and Commissioning of surface mounted satin-finish type 304 stainless steel jumbo roll toilet tissue dispenser complete.
For 35 mm outer dia x 1-1/4” nominal dia threaded
For 42 mm outer dia x 1-1/4” nominal dia threaded
For 54 mm outer dia x 1-1/2” nominal dia threaded
For 54 mm outer dia x 2” nominal dia threaded
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Female Thread Connector/ Adapter
For 35 mm outer dia x 1/2” nominal dia threaded
For 42 mm outer dia x 1-1/2” nominal dia threaded
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Male Thread Connector/ Adapter
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Cap
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Pipe Bridge
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Male Union
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Female Union
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Female Transition Elbow / FTE
Providing & fixing Auto Air vent for water supply risers, suitable for pressure not less than 15 Kg/Sq.cm. 25 mm dia
Supplying, Installation, Testing and Commissioning of motorised valve PN 1.6 of approved quality suitable for high or low pressure complete in all respects.
40 mm dia
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Male Union
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
15 mm dia
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Male Union
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
20 mm dia
25 mm dia
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
32 mm dia
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
SOIL, WASTE, VENT & RAIN WATER PIPES
25 mm dia
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
32 mm dia
Providing and fixing soil, waste and vent pipes :
Sand cast iron S&S pipe as per IS: 1729
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989
75 mm dia
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including
Thermstatic Mixing Valve for Hot and Cold Valve Supply , Installation, testing and Commissioning of Adjustable thermostatic mixing valve. Size DN 20 (from DN 20 to DN 50). Connections 3/4” (from 3/4” to 2”) M (ISO 7/1) with union. Dezincification resistant alloy body. PPSG40, PSU obturator (DN 20). Stainless steel springs. EPDM seals. Maximum hot water inlet temperature 90°C. Minimum hot water inlet temperature 50°C. Maximum cold water inlet temperature 25°C. Minimum cold water inlet temperature 5°C. Adjustment range from 35°C to 65°C. Maximum working pressure (static) 14 bar. Maximum working pressure (dynamic) 5 bar. Minimum working pressure (dynamic) 0,2 bar. Accuracy ±2°C. Minimum temperature difference between hot water inlet and mixed water outlet to ensure optimal performance 15°C. Equipped with tamper-proof temperature locking device
cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :
For 100 mm dia pipe
For 75 mm dia pipe
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.
Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905
For 75 mm dia pipe
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.
Providing and fixing plain bend of required degree.
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Providing and fixing double equal plain junction of required degree.
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Male Union
Providing and fixing double equal plain junction of required degree.
100x100x100x100 mm
75x75x75x75 mm
Providing and fixing single equal plain junction of required degree :
75x75x75x75 mm
Sand cast iron S&S as per IS - 1729
Sand cast iron S&S as per IS - 3989
Providing and fixing double unequal plain junction of required degree :
100x100x75x75 mm
Providing and fixing single unequal plain junction of required degree :
100x100x75x75 mm
75x75x75x75 mm
Sand cast iron S&S as per IS - 1729
Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905
65 mm offsets
With 100 mm dia pipe
With 75 mm dia pipe
130 mm offsets
Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe
SS 304 grade coupling with EPDM rubber gasket
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :
Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
100 mm inlet and 100 mm outlet
Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905
100 mm inlet and 75 mm outlet
Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :
Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6 mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe.
Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe)
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc. Internal work - Exposed on wall
32 mm dia nominal bore
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
40 mm dia nominal bore
50 mm dia nominal bore
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
40 mm dia nominal bore
Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc. Internal work - Exposed on wall
Supplying, Installation, Testing and Commissioning of uPVC, P or S trap of self cleansing design with / without vent. arm Setting in cement concrete 1:2:4 mix complete including cost of cutting & making good the Wall / Floors wherever required. 110 mm inlet & 110 mm outlet
Providing & fixing PVC inlet fitting with one or more inlets fabricated from 110 mm outer dia UPVC pipe and solvent welded sockets and fixed to UPVC Trap and set in cement concrete as per drawing complete
Providing & fixing pvc reducer of required size floor drain of 110 x 63 mm set in cement concrete as per drawing complete
Providing and fixing SS grating of approved quality and colour. Circular type 127 mm nominal dia with 34 mm waste hole.
Making Khurra 45 x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C sheet 1m x 1m x 400 microm, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand ) and a coat of neat cement, rounding the edage and making and finishing the outlet complete.
Providing and fixing SS grating of approved quality and colour. Circular type 127 mm nominal dia with 34 mm waste hole.
EXTERNAL SEWERAGE AND STORM WATER DRAINAGE
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kind of soil Pipes, cables etc, exceeding 80mm dia but not exeeding 300 mm dia
Providing and fixing SS grating of approved quality and colour. Circular type 127 mm nominal dia with 34 mm waste hole.
Providing, laying and joining in position HDPE DWC (Double Wall Corrugated) and conforming to I.S. 16098 of required grade SN-4 and suitable for the respective working pressures with all fittings and specials, e.g. couplings, tees, bends, reducers, screwed adapters, flanged tail pieces, etc., jointing as per manufacturers recommendations, all complete including trenching, backfilling & pressure testing etc. (For Sewer & Storm water line).
150 mm dia
Providing and fixing SS grating of approved quality and colour. Circular type 127 mm nominal dia with 34 mm waste hole.
200 mm dia
250 mm dia
300 mm dia
500 mm dia
Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6 mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe.
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round HDPE. pipes including bed concrete as per standard design:
450 mm dia
Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete ( FOR ROAD CROSSING)
600 mm dia
Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :
0.91 m deep with SFRC cover and frame (heavy duty, HD20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m
Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) f
inished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :
1.68 m deep with SFRC Cover and frame (heavy duty HD_x0002_20 grade designation) 560 mm internal diameter conform_x0002_ing to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 ce_x0002_ment : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :
With Sewer bricks conforming IS : 4885
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m :
With Sewer bricks conforming IS : 4885
Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
EXTERNAL WATER SUPPLY (WITH GARDEN IRRIGATION)
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work
Providing, fixing, Testing and Commissioning of CP brass two way bib cock with wall flange including, necessary flange, cutting and making good he walls / floors wherever required complete.
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
15 mm nominal dia Pipes
Providing, fixing, Testing and Commissioning of CP brass two way bib cock with wall flange including, necessary flange, cutting and making good he walls / floors wherever required complete.
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
20 mm nominal dia Pipes
32 mm nominal dia Pipes
40 mm nominal dia Pipes
65 mm nominal dia Pipes
80 mm nominal dia Pipes
100 mm nominal dia Pipes
150 mm nominal dia Pipes
Providing and fixing CI sluice valve with cap comlete with bolts, nus, rubber insertions etc. the price of required with will be seperately )
Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular)bricks of class designation 7.5
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular)bricks of class designation 7.5
Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular)bricks of class designation 7.5
Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design bricks of class designation 7.5 With common burnt clay F.P.S (non modular)bricks of class designation 7.5
Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular)bricks of class designation 7.5
Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373
Providing and fixing enclosed type water meter (bulk type) conforming to IS: 2373 and tested by muncipal board complete with bolts,nuts, insertions etc. (The tails pieces if required will be paid separately)
Providing and laying D.I. specials of class K-12 suitable for push-on jointing as per IS : 9523 : Up to 600 mm dia
Quintal
Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and the cost of rubber gasket :
100 mm dia pipes
Joint
150 mm dia pipes
200 mm dia pipes
250 mm dia pipes
300 mm dia pipes
Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K - 9 conforming to IS : 8329 :
100 mm dia Ductile Iron Double Flanged
150 mm dia Ductile Iron Double Flanged
250 mm dia Ductile Iron Double Flanged
300 mm dia Ductile Iron Double Flanged
GARDEN IRRIGATION SYSTEM
Providing and fixing UPVC (Unplasticized Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23 °C) for pipes from 1/2" to 2". Schedule 40 Pipe to be used from 2-1/2" to 6". Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, brushings etc. including t
ransition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only UPVC solvent cement conforming to ASTM F-493 with fabricated & subsequently hot dip galvanized clamps / MS (2 coats of enamel paint over a coat of primer) supports as required / directed at site including cutting and fixing the same with anchor fastners, including painting the exposed pipes with one coat of desired shade of enamel paint. All termination points for installation shall have brass termination fittings. The rates to include for chasing in brick masonry / PCC for internal water supply pipes and making good the same in 1:4 cement mortar, cleaning the debris and carting outside the site premises.( for irrigation)
25mm dia
32mm dia
40mm dia
50mm dia
65mm dia
Supply, installation, testing & commissioning of slim seal wafer type butterfly valves class (PN 1.6) with stainless steel (SS) disc complete with matching flanges, EPDM rubber insertion, nuts, bolts and washer etc. of following sizes. (IS: 13095) complete in all respects as directed by Engineer-incharge complete as per standard design. 65mm dia nominal bore
Supply, installation, testing & commissioning of 20 mm PVC RQRC hydrant valve (PN1.0) with PVC lid complete in all respects as directed by Engineer-incharge complete as per standard design.
Providing and fixing 20 mm PVC Keys for hydrant valve complete in all respects as directed by Engineer-incharge complete as per standard design.
300 x 300mm and 500mm deep with 300x300 mm size (inside) water tight FRP cover with frame of grade C-250 (25 T) as per required color coding, fixed in cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) or as per manufacturer recommendation complete in all respects including cutting and making good the wall wherever required and as per satisfaction of Engineer in charge.
PUMPS AND EQUIPMENTS
Supplying, installing, testing and commissioning single stage, submersible centrifugal pumps of closed coupled construction with CI body & cast iron (C.I) impeller connected to a fully submersible water/oil cooled motor suitable to operate with 380-415 volts 3 phase 50 cycles AC power supply with class F insulation and built -in temperature protection, pump connector unit with rubber diaphram & bend, vertical discharge pipe, guide pipe, stainless steel chain/rope, water -proof power cable and level controller complete in all respects for fixed installation.
Pump Room Drainage Pumps - Discharge 5.4M3/Hr Head 22 m Approx. Elec. Load. - 3.5kw 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation
Supplying, installing, testing and commissioning single stage, submersible centrifugal pumps of closed coupled construction with CI body & cast iron (C.I) impeller connected to a fully submersible water/oil cooled motor suitable to operate with 380-415 volts 3 phase 50 cycles AC power supply with class F insulation and built -in temperature protection, pump connector unit with rubber diaphram & bend, vertical discharge pipe, guide pipe, stainless steel chain/rope, water -proof power cable and level controller complete in all respects for fixed installation.
STP area drainage pumps -D1 Discharge 5.4M3/Hr Head 20 m Approx. Elec. Load. - 1.5kw 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation
Providing and fixing horizontical/vertical monobloc centrifugal pumping set Vertical/Horizotal multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS-316 shaft, C.I. Base & head,connected to a IE3 TEFC motor (with mechanical seal) suitable for 400/440 volts, 3 phase, 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating for each pump including necessary structual supports, clamps, bolts, nuts washers and 1:2:4 plain cement concreate (PCC) foundations. Vendor to submit performance curves, dimension detail and technical catalogue of the proposed model for review and approval.
Filter Feed Pump ( 1 Set = 1 working + 1 standby) Location - Plumbing Plant Room Capacity 5.4M3/HR Head 35 m HP/kw Load 5 hp
Irrigation Water Transfer Pump ( 1 Set = 1 working + 1 standby) Location - STP Plant Room Capacity 200 lpm Head 65 m HP/kw Load 5.0 hp
Variable Frequency Drive System: PUMPS Variable Speed Hydro-booster System for domestic water supply :Compact self contained Hydro-booster system comprising of following : In-line, vertical multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS316 shaft, SS-304L/C.I. CED Base coating & head TEFC IE4/IE5 magnetic motor (IE5 is preferable motor for Suitable duties, if duties is not available in IE5 motor then you can quote pump with IE4 motor) with mechanical seal with Company fitted with company compliance certificate. Vendor to submit performance curves and technical catalogue with all GA Drawing of the proposed model for review and information. Panel mounted PLC and HMI Based Precharged diaphragm pressure vessel FRP of suitable size (minimum 100 ltrs capacity) for the system mentioned below with charging connection, connected to outlet header with necessary flanges, gaskets, isolating, valves, nuts/bolts etc. complete.
(iii) Control Panel with IP54 enclosure Class & overload relays and MCBs should confirm specifications. Indications for pumps start, trip, low level trip, healthy supply should be provided in the panel. Single VFD with Cascading arrangment should be provided in the panel, Control Panel should be Equipped with inbuilt PLC
(iv) Pressure switches bellow type fitted with micro switch and having maximum pressure and differential scale should confirming to BS-6134 standards and IP55 protection class.
(v) Pumps should be connected to MS Galvenised Suction & Discharge Header
Hydropneumatic system as described above and as under given capacities:
For supplying DWS to all areas Capacity for Each Pump : 4.2m3/hr Head 70mtr HP/Load 10KW Pressure vessel - Min. 100 liters or as per manufacturer recommendation 2 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation)
For supplying FWS to all areas Capacity for Each Pump : 2.4m3/hr Head 70mtr HP/Load 5KW Pressure vessel - Min. 100 liters or as per manufacturer recommendation 2 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation)
For supplying Irrigation Water Pump Capacity for Each Pump : 10m3/hr STP Room ( Basement level) Head 55mtr HP/Load 5KW Pressure vessel - Min. 100 liters or as per manufacturer recommendation 2 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation)
Water Treatment Feed pumps - (P1) For feeding raw water to water treatment plant and store in domestic water tank Capacity for Each Pump : 5.4m3/hr Plumbing Pump Room ( Basement level) Head 35mtr HP/Load 5KW Pressure vessel - Min. 100 liters or as per manufacturer recommendation 2 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation)
MULTIGRADE PRESSURE SAND FILTER: (For Domestic Water)
Location - Plumbing Plant Room Supply, installation, testing & commissioning of vertical self supporting multi grade pressure filter (MGF) (Dual media filter) fabricated from MS sheet as per IS Code, pressure gauges at inlet & outlet, sample cock, air vent valve with piping, GI face piping distribution pipe with diffuser on top, CI butterfly valves and all accessories, with initial charge of filter media for filter, painting inside with food grade epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint complete with bypass arrangement including piping and valves (3 Nos.) of required size.
Capacity/Flow rate : 5.4 M3/hr Filtration rate/velocity : 15 M3/M2/hr Max. operating pressure : 3.5 kg/Sq.cm Test pressure : 5.5 kg/Sq.cm Suggested diameter : 800 mm
ACTIVATED CARBON FILTER: (For Domestic Water)
Location - Plumbing Plant Room Supply, installation, testing & commissioning vertical self supporting Activated Carbon Filter (ACF) fabricated from M.S. Sheet as per IS Code, pressure gauge at inlet & outl
SOFTENER
Supplying, installing, testing and commissioning of softener of welded construction fabricated from 6mm thick mild steel plates, as per BS Code, lined internally with 3mm thick natural rubber (Shore hardness 60O-80 and continuity test with electrical resistance testing to be done. The vender shall submitted the certificate of having tested the same and externally with approved paint over 2 coats of red oxide primer top and botom dished ends of 6 mm thickness with frontal piping (M.S. fabricated flange pipe work lined internally with rubber similar as for main vessel) and valves back wash fittings and filter media etc. Softener shall be suitable for flow rate and specifications given below with regeneration period of 10 hrs and shall include standard fittings like manhole cover pressure gauges. Sampling cock rinse drain bolts, nuts & rubber gasket etc. complete. The softener plant shall include brine tank of M.S. welded construction lined internally with rubber similar as main vessel and capable of regenerating the softening plant. The brine tank shall have overflow & drain, outlet fitting complete regeneration assembly comprising of power valve, ejector, brine suction valve and all associated pipe work. A density meter for brine shall be included.
Salt Saturation Arrangement: The brine tank shall be provided with salt saturation arrangement (with air agitation) comprising of GI. Perforated (Min. 1 inch.) pipe grid laid in the bottom of brine tank, one no. positive discharge air blower of required capacity, valve & NRV on blower and GI pipe interconnection from blower to grid complete.
Supplying, installing, testing and commissioning electronic chlorine solution dosing system comprising of F.R.P/ chemical grade HDPE solution tank of 200 litres capacity electronic dosing pump of capacity 0-4 LPH against 4.5 Kg/Sq.cm dosing valves, flexible teflon tube pipes etc. complete for dosing of chlorine solution into water on line.
Providing and fixing mild steel (MS) puddle flanges of required size with 5mm thick mild steel (MS) plate including necessary welding as per details shown on drawings and directions of Engineer-in-charge for water tanks.
25mm dia (4mm wall thickness)
32mm dia (4mm wall thickness)
40mm dia (4mm wall thickness)
50mm dia (4mm wall thickness)
65mm dia (4mm wall thickness)
80mm dia (4mm wall thickness)
100mm dia (4mm wall thickness)
150mm dia (4mm wall thickness)
200mm dia (4mm wall thickness)
WTP PANEL Design, manufacture, supply, installation, testing and commissioning of the Plumbing panel, front operated, cubicle construction, Floor mounted type, fabricated out of 16 swg thick CRCA Sheet, Compartmentalized with hinged lockable doors, dust and vermin proof, Powder coated of approved shade, Cable alley, inter-connections, having Switch gear and accessories mounting, internal wiring, earth terminals, Top/ Bottom cable entry, numberings etc. suitable for operation of 415 volts, 3 phase, 50 Hz, AC Supply with enclosure protection class IP 54 complete as required and as specified with the following:
SEWAGE TREATMENT PLANT Design, supplying, installing, testing & commissioning of Sewage Treatment cum Effleunt Treatment Plant for 60 KLD STP + 10 KLD ETP electro mechanical system based on MBBR technology. (excluding all Civil & construction work)
Anticipated effluent parameters before treatment: PH 7.5 - 8.5 BOD 250-400 mg/lt TSS 200-450 mg/lt. COD 600-800 mg/lt. Phosphorus 8-10 mg/lt Total Nitrogen 30-35 mg/lt Oil & Grease upto 50 mg/lt Laundry & OT Effluent Characterstics - 10 KLD pH - 6.0 – 10.0 BOD5 - 200 – 300 Mg/L S. Solids - 150 – 200 Mg/L COD - 800 – 900 Mg/L Desired Sewage discharge standard at UF are as below: PH 6.5 – 8.5 BOD5 Less than 10 Mg/L S. Solids Less than 10 mg/l COD Less than 50 Mg/L Total Nitrogen Less than 10 mg/l Oil & Grease Less than 10 mg/l Sewage treatment plant shall include the following Civil Units : (Client Scope)
Bar Screen Chamber for STP
Oil & Grease Chamber
Sewage equalization tank
Effluent Collection Tank
Coagulation Tank
Flocculation Tank
Primary Tube Settler for ETP
Anoxic Tank
MBBR Tan
SST Tanks
Chlorine Contact Tank
Sludge Holding Tank
Irrigation Water Tank
Flushing Water Tank
Soft Water Tank
Sump Pit
Supply, installation, testing & commissioning of 2 Nos SS 304 Perforated Coarse Type Bar Screen Size 600mm x 800mm with suitable garbage lifting arrangement.
Supply, installation, testing & commissioning of 2 Nos Stainless Steel Perforated, Corrugated Bar Screen with suitable lifting arrangement (size 500 mm wide x 500 mm high approx)
Supply, installation, testing & commissioning of level switch. (Required in equalization tank, chlorine contact tank, sludge holding tank ). Make: Elcare/Cirrus/Baumer
Supply, installation, testing & commissioning of Submersible, non clogging type pumps capable of handling solids minimum 20 mm having CI casing & impeller with SS Shaft complete with mechanical seal & all accessories, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock. Pumps shall have following duty and Cost shall be inclusive of PVC Flexible Pipe 40mm dia , rope for lifting pump from sump to outside.:
Submersible Sewage Transfer Pumps for STP (1W+1S) Flow Rate (each) = 5 m3 / hr Head = 8-10 Mtr Make : Willo/Grundfos/Lubi/KSB
Submersible Sewage Transfer Pumps for ETP (1W+1S) Flow Rate (each) = 1 m3 / hr Head = 8-10 Mtr Make : Willo/Grundfos/Lubi/KSB
Plant room sump pump Flow Rate (each) = 6 m3 / hr Head = 12-15 Mtr Make : Willo/Grundfos/Lubi/KSB
Providing and fixing horizonal,centrifugal sludge recirculation pump . The pumps shall have CI casing, CI Impeller with mechanical rotary shaft seal. Motor to be suitable for including all necessary piping valves and other accessories complete as required. Solid Handling capacity 7mm
Sludge Recirculation Pump (Anoxic To MBBR) (1W+1S) Capacity : 16 Cum/hr. Head :8-10 mtrs. Make : Grundfos/M&P/Lubi
Sludge Transfer Pump (1W+1S) Capacity : 3 Cum/hr. Head :8-10 mtrs. Make : Grundfos/M&P/Lubi
Air diffusion system shall include the following:
Supply, installation, testing & commissioning of twin lobe, rotary Air blower capable of delivering 120 cum/hr of free air at required pressure driven through “V” belt or directly coupled through flexible coupling to a TEFCmotor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. (Blower Make- Everest/ AEW/Beta, Motor Make: Kirlosker/CG/Bharat Bijle) Air Blowers Flow Rate (each) = 120 m3 / hr @ 5000mmwg
Air piping in uPVC complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, paint,supports & clamps, puddle flanges etc cutting chases & making good the wall wherever required. Contactor to submit detailed P & I indicating their proposal.
Non-clog type air dispersion system capable of handling required 3-5/8-10 cfm of air with oxygen transfer efficiency. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily. (Coarse and Fine bubble membrane diffusers. (Make : Rehaue/ Ecologix/OTT) Note: Air dispersion system shall be provided for MBBR Tank, Equalization Tank and Sludge Holding Tank.
Providing and fixing all interconnecting piping (as described below) and isolation control valves for making the system complete. The piping material shall be MS 'B' class. MS Epoxy : Non submerged air piping & pumped effluent riser ( non-submerged) uPVC: Submerged air line. uPVC Piping : Interconnecting pipe line after delivery header of pump / filter Make : Jindal-Hissar/Tata/Supreme/Astral/Prince
Supply, installation, testing & commissioning of Anoxic mixer for Anoxic Tank. 2 Nos. (1W+1S) Make: Accua Itly/Toro/ATE/Sulzer/Grundfos
Supply of MBBR media consisting of recyling PE carrier modules with Surface not less than 400 M2/M3 of suitable capacity and as per manufacturer's recommendation for Reactor tanks alongwith suitable sludge removal arrangement either by pumps or air lifting pumps. Make : MM Aqua/Cooldeck/One Point
Supply, installation, testing and commissioning of PVC tube deck settling media to be installed in primary and secondary tube setller tank alongwith suitable sludge removal arrangement either by pumps or air lifting pumps. Make : MM Aqua/Cooldeck/One Point
Supplying, installing, testing and commissioning of dosing system consisting of one HDPE tank of 100 litres capacity with a positive displacement diphragm dosing pump having variable flowrate of 0-12 lph, 2 Nos. (1W+1S). The motor shall be suitable for operation at 240 V/single phase/50 Hz. Supply. The pump shall be supplied complete with necessary polypropylene piping, valves, strainers, low level switch and injection fittings. The pump shall be speed & stroke control. Make Dosing Pump: Grundfos/Prominent/Toro
Supplying, installing, testing & commissioning of horizontal centrifugal water pumps CI Head & Base, CI Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer (with by-pass) at suction. Mechanical seal, suitable vibration elimination pads of approved design, drain pipe with valve (25 dia) for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply. Make:Grundfos / M&P/Lubi
Filter feed pumps: (1W+1S) Capacity : 5 Cum/hr. Head :30 mtrs.
Softner pumps: (1W+1S) Capacity : 4 Cum/hr. Head :25 mtrs.
Softner Water Transfer pumps: (1W+1S) Capacity : 5 Cum/hr. Head :55 mtrs.
Irrigation Water Transfer pumps: (1W+1S) Capacity : 5 Cum/hr. Head :35 mtrs.
Supplying, installing, testing and commissioning of MSFRP vessel filter with all necessary accessories. Filter shall be suitable for minimum working pressure of 5 kg / cm2 and shall include media, standard fittings like pressure gauges, sampling cock, rinse drain, vacuum breaker etc. Make: Thermax/Ion Exchange/Ecologix/Neerway
Multigrade pressure sand filter Capacity : 5 Cum/hr. Filteration velocity : 15 cum/hr/sqm HOS : 1800 mm filtering sand, anthracite, pebbles and gravel media
Activated Carbon Filter Capacity : 5 Cum/hr. Filteration velocity : 15 cum/hr/sqm HOS : 1800 mm filtering sand, anthracite, pebbles and gravel media
Supply, installation, testing and commissioning of Hydraulic Operated Filter Press of Plate size 450x450mm, 17 Plates, interconnecting piping and poly dosing system, 2 Nos. (1W+1S). Filter Press Make : Auro/Ecologix/Sachin Dosing Pump: Grundfos/Prominent/Toro
Supply, installation, testing & commissioning of positive displacement type screw slurry pump with MS casing, SS-strator with internal rubber lining, gland packing seal, solid handling capacity upto 7 to 10% of the effective percentage of sludge and direct drive with motor. (1W+1S) Sludge Feed Pump Capacity : 1 m3/hr Head : 30 mtrs. Make : Roto/Rotomac
Supply, installing, testing & commissioning of ultravoilet dis-infection unit. The unit shall have over 99.9 % bacterial reduction from inlet to outlet. The dis-infection chamber shall be constructed of SS 316L on all welted parts. The UV lamp shall be of low pressure mercury vapour type with hard glass enclosure, the sockets shall be water tight & vibration resistant. The lamp life shall be rated for 6000 hours. (1W+1S). Qty : 2 Nos. Flow Rate : 6 m3/hr Dosing Pump: Alfa Mumbai/ Sukruit/One Point
Providing and fixing water softener fabricated MSRL. M.S. plate on dished ends (
For 54 mm outer dia x 2” nominal dia threaded
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Female Thread Connector/ Adapter
For 35 mm outer dia x 1/2” nominal dia threaded
Supplying, Installation, Testing and Commissioning of surface mounted satin-finish type 304 stainless steel jumbo roll toilet tissue dispenser complete.
Quality of Steel as per IS:2062 Grade B, thickness as per ASME Section 8) complete with initial charge of filter media and resins, face piping accessories, diaphragm valves of approved specifications, MSRL Brine tank, piping testing and commissioning complete with resins of approved quality and make and regeneration assembly complete with valves, ejector, brine suction valves and piping. (Bidder must indicate type and quantity of resin used and quantity of salt required per regeneration). All internal parts of the softener shall be rubber lined as per approved specifications. Make: Thermax/Ion Exchange/Ecologix/Neerway Raw water hardness 600 Mg/L Treated water harness 50 Mg/L Regeneration Period 40 KL Capacity : 4 m3/hr each
Providing, fixing, Testing and Commissioning of CP brass two way bib cock with wall flange including, necessary flange, cutting and making good he walls / floors wherever required complete.
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Flushing Water Transfer Pumps
Variable Speed Hydropneumatic System for Domestic Water Supply Distribution to Terrace Water Storage tank : Supply installation testing & Commissioning of Factory fitted & supplied package type (Skid Mounted) compact self contained Hydropneumatic system comprising of following : In-line, multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base & head TEFC motor (with mechanical seal) Vendor to submit performance curves dimension detail and technical catalogue of the proposed model for review and approval. Make: Wilo / Grundfos / Lubi/KSB Capacity/Flow rate : 7.5 m3/hr. of each pump Pumping Head : 55 -60 m 1 Set : 2 Nos. pump (1w+1s) Flushing Water Transfer Pumps to overhead tanks
Instrumentation Supply and fixing of following instrument :
Providing and fixing full bore type Electro-magnetic flow meter of suitable dia designed at maximum speed of 3-4 m/sec at the sewage inlet and outlet Make : Krone Marshal/Toro/Hach/E&H
Providing, installing, testing and commissioning of Online digital type pH meter. Make : Forbes Marshal/Toro/Hach/E&H
Supplying, Installation, Testing and Commissioning of surface mounted satin-finish type 304 stainless steel jumbo roll toilet tissue dispenser complete.
Quality of Steel as per IS:2062 Grade B, thickness as per ASME Section 8) complete with initial charge of filter media and resins, face piping accessories, diaphragm valves of approved specifications, MSRL Brine tank, piping testing and commissioning complete with resins of approved quality and make and regeneration assembly complete with valves, ejector, brine suction valves and piping. (Bidder must indicate type and quantity of resin used and quantity of salt required per regeneration). All internal parts of the softener shall be rubber lined as per approved specifications. Make: Thermax/Ion Exchange/Ecologix/Neerway Raw water hardness 600 Mg/L Treated water harness 50 Mg/L Regeneration Period 40 KL Capacity : 4 m3/hr each
Providing, fixing, Testing and Commissioning of CP brass two way bib cock with wall flange including, necessary flange, cutting and making good he walls / floors wherever required complete.
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
Providing and fixing of suitable size pressure gauge boudron type glycerin filled. Make : H Guru
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)
Supplying, installing, testing & commissioning of Cables , Conector, Cable Trays, to make Electrical Installation Complete. Cable Make: Polycab/Finolex/National or equivalent Cable Tray Make: Super/Slotco/MEM
Providing, installing, testing and commissioning of Ultra Filtration (UF) system for further polishing treated effluent and capable of producing 3000 litre / hour of polished water meeting the requirements . The system shall be complete with UF Feed Pumps (1W+1S), Membranre Flushing Pumps (1W+1S) in SS 316, Cartridge Filters, 0-12 LPH Dosing Pump (2W+2S), UF Membranes Flushing , complete instrumentation for automation, PLC+HMI and monitoring, Rotameters, Pressure Gauges, interconnecting pipework, electrical cabling and switchgear, all complete as described in Scope of Work enclosed herewith. Membrane MOC - PVDF, Membrane Type :- Pressure Feed Mambrane 25 micron cartridge type, Out to in process Dosing Pump Make: Grundfos/Prominent/Toro PANEL Make: Ambit/Bew/SPC/Adlec/Tricolite/Neptune Pump Make : Willo/Grundfos/Lubi/KSB Membraine Make: Qua/Dow/Torray
FIRE FIGHTING PUMPS
Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (a) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. (b) Suitable HP squire
ll cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (c) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 88 m Head
CONTROL PANELS Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter- connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :
Flextra 150 expansion joints use an integral sleeve support on the retaining ring, and has a wide arch for greater movements. 150 dia
PIPES & ACCESSORIES
Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150mm dia
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
65 mm dia
200 mm dia (wall thickness 6.3 mm)
Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80mm
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal
Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :
Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required :
Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 mm dia
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gunmetal
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30m
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gunmetal
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :
2 way-100 mm dia M.S. Pipe
4 way - 150 mm dia M.S. Pipe
Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :
Pendent Sprinkler
Upright Sprinkler
Horizontal side wall sprinkler
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.
100mm dia
150mm dia
Providing, fixing, testing & commissioning of ins
tallation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of following sizes as required : 150mm dia
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.
Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.
Providing, fixing, testing & commissioning of MS Air Cushion Tank on top of riser fabricated from 6mm thick MS plate, 200 mm in diameter and 1.2 m in height with dished ends fabricated from 8mm thick MS plate with Air release valve with stop cock, flanged inlet connection and drain arrangement with 25mm dia valve, pressure gauge with gun metal stop cock complete with all accessories as required and conforming to IS 4736-1968.
Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.
Providing and fixing fully glazed MS fully welded construction double leaf door shutter for fire hydrant station fabricated from MS 50x50x6 mm angle iron frame, fixed to wall and hinged MS 40x40x5 mm angle iron door shutter with required MS sash bars for glazing Fire Door Approximate size 2100x900 mm.
Providing and fixing Weather proof hose cabinets for yard hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos. 15m long hose, 1 No branch pipe and one fireman's axe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.75mx0.6 mx 0.25 m).
Note: (a) For Cabling, earthing and cable trays please refer to DSR (E&M) (b) For digging of hard & soft soil please refer to DSR (Civil)
GAS FLOODING SYSTEM
Clean Gas Fire Suppression Systems 1x80 Itr completele CCOE approved high pressure seamless BIS 7285 approved Cylinders having 80 ltr capacity, UL/FM/VDS approved FK5-1-12 clean agent gas with UL/FM/VDS listed valve assembly and electric solinoid switch. The system also to be fitted with low pressure supervisory switch for monitoring cylinder pressure gauge with safety burst disc safety cap, elbow and other accessories, mounting bracket, container straps, NRV , Pressure operated control head which shall allow for pressure actuation of gas mounted, manually operated actuator to actuate the gas flooding process with the help of a lever, flexible rubber hose with wire bralded enforcment to route the gas from the storage cyinder to the discharge piping, to be connected to the discharge outlet of gas cylinder valve & to be terminated at the system piping or discharge manifold, Flexible actuation hose complete as required. Discharge nozzle, 180/360 degree. Designated to provide proper flow rate & distribution FK5-1-12 gas to flood the hazard area as per latest NFPA 2001 requrement. Piping ASTM grade A 106 schedule 40 with fittings & supports and Gas Release Panel compatible to Fire Alarm System .
10 LB capacity Novec 1230/FK5-1-12 , DLP Assembly with automatic valve mounted on DOT approved cylinder, push in connector for tube,10LB Novec 1230/FK5-1-12 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.
Linear pneumatic heat Detection Tube with all necessary fittings & supports.
Master Control Unit with Audio Visual Alarm With Wiring to Make Complete System Operational. The Control Panel Should have Provision for integration with Fire Alarm/ SCADA/ BMS System
Master Control Unit with Audio Visual Alarm With Wiring to Make Complete System Operational. The Control Panel Should have Provision for integration with Fire Alarm/ SCADA/ BMS System
FIRE EXTINGUISHERS
Providing and fixing mechanical foam type (ISI marked) fire extinguishers consisting of welded M.S. cylindrical body squeeze lever discharge valve 30 cm long high pressure discharge hose, discharge nozzle, suspension bracket as per ISI marked finished externally with red enamel paint and fixed to wall with brackets complete with internal charger. Capacity 9 lit.
Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed conforming IS : 15683:2006
4.5kg capacity cylinder
22.5 kg (Trolly Mounted)
Providing and fixing water based CO2 type extinguishers consisting of welded M.S. cylindrical body, squeeze lever discharge valve 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:934 finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. Capacity 6.5 KG
Providing and fixing ISI marked portable fire extinguishers of the following type. Dry Chemical Powder ABC type of 6 Kg as per IS:15683
ELECTRICAL WORKS
CHAPTER-1-WIRING
WIRING IN PVC CONDUIT
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
Point
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC Insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with. 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
Wiring for MCB controlled (looped) light point/fan point/exhaust fan point/ call bell point with 1.5 sq. mm FRLS PVC Insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with. 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Note : Wiring for Corridor and Staire case Group C
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
2 x 6 sq. mm + 1 x 6 sq. mm earth wire
2 x 10 sq. mm + 1 x 6 sq. mm earth wire
2 x 16 sq. mm + 1 x 6 sq. mm earth wire
4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire
4 X 6 sq. mm + 2 X 6 sq. mm earth wire
4 x 10 sq. mm + 2 x 6 sq. mm earth wire
4 x 16 sq. mm + 2 x 6 sq. mm earth wire
LED Down lighter (SMD Type) (System lumen efficacy >135 lm/Watt)
Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round /square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K / 6000°K /6500°K (As per ANSI Bin) , SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminum Body including trim
12 -15 watt (12 watt)
12 -15 watt (15 watt)
LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt)
Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm)
LED Batten light (System lumen efficacy ≥120 <135 lm/Watt)
Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range 15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20
, CRI >80 , Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends,CCT 3000°K / 4000°K / 5700°K /6000°K /6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm)
Brush Less Direct Current (BLDC) Motor Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal (Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as reqd 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)
Supply, Installation, Testing and Commissioning of Ceiling / Recessed LED light Fixtures / Exhaust Fan etc. as mentioned below :
10 W LED Mirror Light
10 Watt LED Bulkhead Light
55/80W LED Lowbay/HIghbay Light
10 W LED Mirror Light
Exhaust Fan (300 mm Dia. Heavy Duty with louver shutter)
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fluxing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fluxing 3 pin 5/6 A modular socket outlet, connections etc. as required.
Supplying and fixing suitable size Gi box with modular plate and cover in front on surface or in recess, including providing and foxing 2 nos 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
Supplying and fixing suitable size Gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
Supplying and fixing brass batten/ angle holder including connection etc. as required.
Supplying and fixing call belli buzzer suitable for single phase, 230 V, complete as required.
Providing and fixing extra conduit down rod of 20 mm dia, 2 X 10 cm length, wiring with 2 X 1.5 sq. mm FRLS PVC Insulated, copper conductor, single core cable including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be lanored)
Installation, testing and commissioning of celling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.
Supplying and fixing extra down rod of 10 cm length G.I. pipe,15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)
Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)
Supplying & fixing suitable size Gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 Amodular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.
CHAPTER-2-MCCB, MCB & DB'S
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board 240 V. on surface récess, complete with toned copper bus bar, neutral bus bar, earth bar, din bar interconnections, powder painted including earthing etc as required. But without MCB/RCCB/Isolator)
8 way, Double door
12 way, Double door
Supplying and foxing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with linned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
6 way (4+18), Double door
), Double door
Supplying and fixing of following ways surface recess mounting. vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note: Vertical type MCB TPOB is normally used where 3 phase outlets are required.)
4 way (4+12) Double door
12 way (4+36), Double door
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve. miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, lesting and commissioning etc, as required
Single pole
Single pole and neutral
Double pole
Triple pole
Triple pole and neutral
Supplying and fixing 40 A to 250 A rating, 240/415 V, 10 /15 kA, "C" curve. miniature circuit breaker or MCCB (Thermal magnetic based release) suitable for inductive load of following poles in the existing MCB/MCCB DB complete with connections, testing and commissioning etc, as required
40/63 A Single pole MCB, 10 KA
40/63 A Double pole MCB, 10 KA
40/63 A Tripple pole MCB, 10 KA
40/63 A Four pole MCB , 10 KA
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc, as required
Supplying and foxing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.
Supplying and foxing 25A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess. with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
Supplying and fixing 30 A. 415 V. TPN Industrial type socket outlet with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc as required
Providing and fixing MV. danger notice plate of 200 mm X 150 mm. made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides and with insonption in single red colour on front side as required
Providing and fong HT danger notice plate of 250 mm X 200 mm made of mild steel, at least 2 mm thick and vitreous enameled white on both sides and with insomption in single red colour on front sida as moured
CHAPTER-3-RISING MAINS & BUS TRUNKING
Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains/Bus Duct for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required.
500 A, Isc= 30kA for 1 sec
630 A, Isc= 50kA for 1 sec
1250 A, Isc 50kA for 1 sec
1600 A, Isc= 50kA for 1 sec
Supplying, installation, testing & commissioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without МССВ/АСВ) сomplete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required
500 A, Isc= 35kA for 1 sec
630 A, Isc 50kA for 1 sec
Supplying, installation, testing & commissioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required 125 A, Isc 15kA for 1 sec / 100 A
Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.
100 A16KA PMCCB
125 A36KA FPMCCB
630 A 50KA, FPMCCB
CHAPTER-4-CABLE TRAYS
Hot Dipped Galvanized Iron Cable Tray
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.
150 mm width X 50 mm depth X 1.6 mm thickness
300 mm width X 50 mm depth X 1.6 mm thickness
450 mm width X 50 mm depth X 2.0 mm thickness
600 mm width X 50 mm depth X 2.0 mm thickness
900 mm width X 62.5 mm depth X 2.0 mm thickness
Providing and Laying of Factory Fabricated G.I. Raceways with removable cover, suitable size of junction box of following sizes of raceway in floor / surface including fixing arrangement, cutting of existing floor finish level, hook, etc complete as required.
100x38x1.6x2 -1Comp 2.5Mtr 275GSM
225x38x1.6x2 -3Comp 2.5Mtr 275GSM
250x38x1.6x2 -3Comp 2.5Mtr 275GSM
CHAPTER-5-EARTHING
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coke and salt as required.
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with Gl thimble etc. as required.
Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt &
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spring washer spaced at 50mm)
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
Providing and fixin
g earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.
Providing and fixing earth bus of 50 mm X 5 mm GI strip on surface for connections etc. as required.
CHAPTER-6-LIGHTNING CONDUCTOR
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
Jointing copper / G.I. tape (with another copper/ GI tape, base of the finial or any other metallic object) by riveting/ nut bolting/ sweating and soldering etc as required.
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.
Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
Supply, Installation, Testing and Commissioning of Lightning Counter with LCD screen and all allied accessories as per site requirement.
CHAPTER-7-MV CABLE LAYING
Supplying of the following sizes of 1.1 kv aluminium conductor XLPE insulated and PVC sheathed armoured cable as per IS: 7098:1988 (Part‐I) with upto date amendments.
3.5CX300 SQMM AL
Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
Supply, Installation, Testing and Commissioning of Lightning Counter with LCD screen and all allied accessories as per site requirement.
CHAPTER-7-MV CABLE LAYING
Supplying of the following sizes of 1.1 kv aluminium conductor XLPE insulated and PVC sheathed armoured cable as per IS: 7098:1988 (Part‐I) with upto date amendments.
1CX70 SQMM Copper
Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
Supply, Installation, Testing and Commissioning of Lightning Counter with LCD screen and all allied accessories as per site requirement.
CHAPTER-7-MV CABLE LAYING
Supplying of the following sizes of 1.1 kv aluminium conductor XLPE insulated and PVC sheathed armoured cable as per IS: 7098:1988 (Part‐I) with upto date amendments.
1CX16 SQMM Copper
Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
Supply, Installation, Testing and Commissioning of Lightning Counter with LCD screen and all allied accessories as per site requirement.
CHAPTER-7-MV CABLE LAYING
Supplying of the following sizes of 1.1 kv aluminium conductor XLPE insulated and PVC sheathed armoured cable as per IS: 7098:1988 (Part‐I) with upto date amendments.
3.5CX185 SQMM AL
3.5CX150 SQMM AL
3.5CX120 SQMM AL
3.5CX95 SQMM AL
3.5CX70 SQMM AL
3.5CX50 SQMM AL
3.5CX150 SQMM AL
3.5CX120 SQMM AL
3.5CX95 SQMM AL
3.5CX70 SQMM AL
3.5CX35 SQMM AL
4CX25 SQMM AL
3CX25 SQMM AL
4CX16 SQMM AL
4CX10 SQMM AL
4CX6 SQMM AL
4CX25 SQMM AL (Fire Survival)
3CX25 SQMM AL (Fire Survival)
3CX120 SQMM AL (Fire Survival)
3.5CX185 SQMM AL (Fire Survival)
3.5CX300 SQMM AL (Fire Survival)
4CX16 SQMM Cu
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
Upto 35 sq. mm
Above 35 sq. mm and upto 95 sq. mm
Above 95 sq. mm and upto 185 sq. mm
Above 185 sq. mm and upto 400 sq. mm
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonary open duct as required.
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required.
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.
Upto 35 sq. mm (clamped with 1mm thick saddle)
Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)
Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.
Supplying and making cable route marker with cement concrete Each 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.
Providing and fixing health faucet with 1 m ss braided hose pipe and swivel hook including all fittings complete.
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.
Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
CHAPTER-8-HT CABLE LAYING / SUPPLY
Supply, loading, transportation, unloading at site, storages at site, shifting from storage place to site of following sizes of 11KV grade conforming to IS amended upto date and as per specifications. 3C X 240 sq.mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/HUME/METAL pipe as required. Above 120 sq. mm and upto 400 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonary open duct as required. Above 120 sq. mm and upto 400 sq. mm
CHAPTER-9-MV CABLE JOINTING & END TERMINATION
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ X 35 sq. mm (32mm)
3½ X 50 sq. mm (35mm)
3½ X 70 sq. mm (38mm)
3½ X 95 sq. mm (45mm)
3½ X 120 sq. mm (45mm)
3½ X 185 sq. mm (57mm)
3½ X 300 sq. mm (70mm)
4 X 16 sq. mm (28mm) / 4 X 10 sq. mm /4 X 10 sq. mm
4 X 25 sq. mm (28mm)
3 X 25 sq. mm (28mm)
CHAPTER-10-HV CABLE JOINTING & END TERMINATION
supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required: 240 sq. mm
supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required: 240 sq. mm
CHAPTER-14-MISC. CIVIL ITEMS
Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required
Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement: 2 fine sand) including trenching (75 cm deep) and refilling etc as required.
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.
120 mm dia (OD-120 mm & ID-103 mm nominal)
200 mm dia (OD-200 mm & ID-175 mm nominal)
CHAPTER-15-LIGHTING CONTROLS
Supplying, installation, testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor with day light dimming(lighting level shall be regulated as per availability of natural day light in an area along with occupancy detection.) having high preformance, regulating programmable type, suitable for connected load upto 10Amp for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.
Supplying, installation, testing and commissioning of Microwave technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10Amp, for mounting height up to 2.6 mtr and for 5m X 20m coverage area along with necessary fixing ar
rangements i/c programming at site etc. complete as required.
PUBLIC ADDRESS SYSTEM
Supplying, Installation, testing & commissioning of 6 Zone, Voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation as required.
Supplying, installation, testing & commissioning of 6W ceiling speaker complete as required.
Supplying, installation, testing & commissioning of 6W wall mounted speaker complete as required.
Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface /recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable Single pair, 2-core, 1.5 sqmm
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm
Supply, Installation, Testing & Commissioning of 42U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.
Providing and fixing of self illuminated / auto glow "EXIT" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 400 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site etc. complete as required.
Supply, Installation, Testing & Commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.
Supply, installation, testing and commissioning of Audio Mixer as per site requirement.
DATA , VOICE & Wi-Fi SYSTEMS
Supply, Installation, Testing & Commissioning of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimu 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75 mmX75 mm)
Supply , Installation , Testing and commissioning of 6 Fiber Multimode (OM4), Low Smoke Zero Halogen, 50/125 Fiber Cable, Indoor/Outdoor Fiber Cable with LSZH Tight Buffered Fibers, Non Jelly (Jel Free), Armaid Yarns, LSZH Inner Jacket, Corrugated ECCS Tape Armor, UV-LSZH Outer Jacket, IEC 60332-3-22 Flame Rated, Overall Nom. Diameter < 12.5mm, Crush Resistant 2200N/100mm, Tensile Strength 2100N, Operating Temperature : -20 to + 70 Deg C, Max. Attenuation @850nm & 1300nm : <= 3.5dB/km & <= 1.5dB/km Respectively, Black Color Fiber etc complete etc as reqd.
Supplying, installation, Testing and commissioning of following capacity 24 port Layer 2 indoor Network Switch having features and specifications etc. as mentioned here under: At least 24 X RJ-45 Gigabit Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking architecture by having Switching capacity of min. 168Gbps and packet forwarding rate of 125Mpps or higher, 16K MAC table. Console Port, USB port, Stacking support of min. 8 units per stack. Internal dual AC Power supply, STP, RSTP, MSTP, BPDU Filter, BPDU Restriction, Min. 9K Jumbo Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD Groups 1K or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ß ß-in-ß VLAN Trunking, DHCP Snopping, Server, server Screening. RADIUS , TACACS ß ß WRED, 802.1p. ACL: MAC based, IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client, LLDP, LLDP-MED, OAM, Dying Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV surge protection on all Gigabit Ethernet ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required.
24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each copper port supporting 802.3at PoE+ min.
24 port Layer 2 Non-PoE Network Switch
Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, Non- Plenum, Horizontal (solid) Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL etc. complete as required. 1 Run of cable
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm
Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.
Copper Patch Cords of length 1m (3ft)
Copper Patch Cords of length 3m (10ft)
Supplying and fixing Patch Cord of Optical Fiber Multi Mode or Single Mode LC to LC Fiber Duplex having high precision ceramic ferrule with good concentricity, Fiber corning single mode G652D, Cable Type 2mm with Mechanical specification Apex Offset < 50 µm, Fiber Height + 100 nm, E nd-face radius of Curvature 7mm < R <25mm, Repeatability < 0.2 db, Working ambient Temperature 5°C to +50° C, Storage Temperature 10° C to +50° C, Length -- 2meter, Type -- LC-LC Duplex etc complete as required.
Supply and fixing following port Rack Mount loaded LIU with pigtail, Front-mounted cable saddles for jumper management, suitable to manage both splices and terminations, Pre-assembled shelves in multiple configurations, Rubber fiber slotted bracket built-in, metal splice shelf to protect the fibers, 2 fiber spools built- in for 900 µm tight buffered fiber storing, Capable of storing up to 3 metres of 900 µm tight buffered fiber per adapter, emovable front and rear covers for better access to interior of LIU, Should be Single / Multi mode LC Type fully loaded. Accessory kit consists of cable ties, mounting ear screws, and spiral wrap tube etc complete as required.
12 Port LIU
24 Port LIU
Supply, Installation, Testing & Commissioning of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimu 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.
Supply , Installation , Testing and commissioning of loaded 24 port CAT6A U/UTP Jack Panel 24-Port 1U Universal Modular Straight Patch Panel preloaded with cable support Bar (with slots to tie individual cable properly at the Support Bar), Stainless Steel Rear Metal Frame, Individual Port Transparent Shutter and Labelling, UL 1863 Complied, CRC Metal with Black Powder Coated, RoHS Compliant, Individually Replaceable Port IO, (Shuttered IO not recommended, because when shutter gets malfunctioned then entire IO is of no use), for CAT6A cable
termination. For DATA etc complete etc as reqd.
Supply, Installation, Testing & Commissioning of Core Switch should have the 24 x 1/10G/25G ports fiber ports should have 2 x 40/100G QSFP+ ports, 3.6 Tbps of switching capacity, 16GB DRAM and 16GB Flash/Storage, The switch should support 128K IPv4 routes and 64K IPv6 routes entries in the routing table, 64K multicast routes, stacking bandwidth 160Gbps .
Supply, Installation, Testing & Commissioning of Core Switch should have the 24 x 1/4G/10G ports fiber ports should have 2 x 10/25G QSFP ports, 3.6 Tbps of switching capacity, 16GB DRAM and 16GB Flash/Storage, The switch should support 128K IPv4 routes and 64K IPv6 routes entries in the routing table, 64K multicast routes, stacking bandwidth 160Gbps .
Supply, Installation, Testing & Commissioning of MM fiber Modules 1000BASE complete etc as reqd. 5year Hardware replacement warranty.
Supplying and fixing 42U Rack with 6 inch Castor wheels and front brake Floor Standing Rack with Main Frame Pillar of 1.6mm CRCA Sheet with removable side panels, L- Shape adjustable Vertical Mounting Rail of 2mm with 'U'Marking completely knocked-down condition (CKD) Shape, fitted with 4 number cooling fans, minimum 8nos two line cable entry/exit provision at top and bottom with rubber protection, Front door 5mm Toughened Glass with MS frame or MS perforated with lock, Rear MS vented or perforated door, Powder coated Color- RAL- 7035 or black, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc. complete as required.
Supplying and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm CRCA Sheet, completely knocked-down condition (CKD) Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking, Minimum 2 cable entry/exit provision at Top and bottom with rubber protection, Front 5mm Toughened Glass with lock, wall mounting kit, Powder coated Color- RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc. complete as required.
9U Rack
15U Rack
IP-PBX SYSTEM (Wi-Fi)
Supplying, Installation, Testing and commissioning of indoor Wireless Access Point for High density use having features and specifications etc. as mentioned here under- WiFi6 802.11ax 574Mbps (2.4GHz) + 2402Mbps (5GHz), WIFI 6 Certified, 1 x RJ45 console port, MG 2.5G LAN POE Port, factory reset, WPA/WPA2/WPA3™ Personal/Enterprise, WEP 64/128-bit, SSID broadcast disable, MAC address access control, Internal RADIUS server, SNMP, Customizable Captive Portal, Auto Channel, Works as Access Point, WDS, WDS with AP, Wireless Client ., Web (HTTP), Secure Socket Layer (SSL), Traffic control, Support ATF/Fast Roaming/Band Steering, Supports enhanced security – WPA-PSK/WPA2-PSK/WPA3-PSK and RADIUS client, and Cipher negotiation, and MAC/ IP ACL for networks, Certifications: MTCTE, CE, FCC. Works as Standalone, Compatible with S/W & H/W Controller with addtional features like - Real-Time Monitoring and Alerts, Rich Advanced Features, Centralized Device Management, Role-Based Administration, Real-Time Monitoring, VLAN and Access Control, Auto RF Management and Bandwidth Optimization, Multi-SSID and Captive Portal Authentication.OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required.
Supplying, Installation, Testing and commissioning of indoor Wireless Controller having features and specifications etc. as mentioned here under- The network controller shall be a dedicated hardware appliance designed for centralized management of wireless access points, It must support the management of up to 500 networking devices, The system should be on-premise, ensuring data privacy and complete control over network configurations. It must include an intuitive user interface for real-time monitoring, device discovery, firmware upgrades, scheduling, and mass configuration deployment. Features such as role-based administration, multi-site management. AP to controller communication shall be use of industry standards-based (IEEE or IETF) CAPWAP or any tunneling protocols as per guidelines of DoT.The controller should support Layer 2 and Layer 3 device discovery, VLAN configuration, MAC ACL groups, IGMP snooping, and bandwidth optimization. Automatic radio frequency (RF) management and access policy enforcement are required for reliable wireless performance. The solution must offer a comprehensive dashboard with network topology, floor plan views, client and device lists, and alert notifications. For authentication, it should support a range of methods including local database, external RADIUS, LDAP, and passcode or MAC-based access. It should provide detailed traffic analytics, logs, and customizable reporting for network visibility and planning. Firmware and configuration backup and restoration functions must be available, with USBbased log storage supported. Physical specifications should include a compact form factor with a minimum of one 2.5G Ethernet port and USB 3.0 port, and it must be MT
CTE,CE, FCC, and RoHS certified. The controller should operate reliably within a 0°C to 40°C temperature range and 10–90% non-condensing humidity. /Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required.
IP-PBX SYSTEM
Supplying, installation, testing and Commissioning of IP based voice communication system with 04 Port Voicemail, 04 Port FXS, 04 Port FXO, 1 PRI Trunk lines (30 Channels) Circuit with CLIP Facility, min 100 IP users License with provision for further additions, 100 analog users, 01 Number IP based Operator Console, 100 Party Conference, Speed Dial, Music on Hold, Internal/ External ring difference, Call Barring, Call Pickup, Redundant server in active -Active mode and as per technical specification including supporting accessories etc complete as required. The system should have valid TEC GR approval from DoT.
Supplying, Installation, Testing & Commissioning of Type 1 IP Phone having 2 VoIP account, 120 x40 DOT matrix screen with backlight, Full HD duplex speaker phone, IPV6, Gigabit Etherent, PoE etc. complete as required.
Supply, Installation, Testing & Commissioning of Type 2 IP Phone with 4 Voip accounts, 4 line keys, 3.5-inch (480x320) Colour Screen display with backlight, GigE, colour displays for 6 DSS keys, 2 x Gigabit Ethernet , PoE.
MATV SYSTEMS
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75 mmX75 mm)
Supplying and fixing following size/ Splitter Box alongwith with all allied accessories as required.
CHAPTER-15-LIGHTING CONTROLS
Supplying, installation, testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor with day light dimming(lighting level shall be regulated as per availability of natural day light in an area along with occupancy detection.) having high preformance, regulating programmable type, suitable for connected load upto 10Amp for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.
Splitter Box - 2 way
Splitter Box - 4 way
ADDRESSABLE TYPE FIRE DETECTION AND ALARM SYSTEM
Supplying, installation, testing & commissioning of Central graphical Fire Alarm management system to centrally monitor and operate the fire alarm system complete as required to complete the job.
Supplying, installation, testing & commissioning of Repeater panel with 320 character / Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required to complete the job.
Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector (Smoke Detector) complete with base and all allied faciltiy as per requirement complete as required to complete the job.
Supplying, installation, testing & commissioning of intelligent addressable thermal Detector with rate of rise cum fixed temperature thermistor complete with base as required & as per requirement.
Supplying, installation, testing & commissioning of addressable Beam detector with short circuit isolator (inbuilt or separate) complete with emitter and reciever including connections with remote test features etc complete as reqquired.
Supplying, installation, testing & commissioning of intelligent addressable multi criteria detector complete with base as required & as per requirement.
Supplying, installation, testing & commissioning of Fault isolator complete with base as required to complete the job.
Supplying, installation, testing & commissioning of addressable manual call point complete as required.
Supplying, installation, testing & commissioning of addressable horns cum Strobe complete as required.
Supplying, installation, testing & commissioning of response indicator on surface/recessed MS box having two LED, metallic cover complete with all connections etc as required.
Supplying, installation, testing & commissioning of fire fighter phone jack complete as required as required.
Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.
Supplying, installation, testing & commissioning of addressable Fire Control Module complete as required.
Supplying, installation, testing & commissioning of addressable Monitor Module complete as required.
Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.
CCTV (IP VIDEO SURVEILLANCE) SYSTEM
Supplying Installation Testing and Commissioning of 5/6MP IP IR Dome Camera having following specifications and features etc :- 1)Type of Camera: Dome Camera 2) Image Sensor: 1/2.8" or
better progressive Scan CMOS get color image even at night condition 3) Signal System: PAL/NTSC 4) Minimum Illumination: 0.008Lux@ F1.4, AGC ON, 0 lux with IR or better 5) Imaging: 1/3s to 1/30000s Shutter Support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. 6) On Screen Display: Camera should display Camera title, Date & Time in live & recorded video both. 7) Signal to Noise Ratio: > 50 dB 8) Day & Night: True Day & Night High Performance Mechanical IR cut filter with auto switch, IR Source Inbuilt IR LED's with effective distance upto 50 Mtrs integrated IR 30 Mtrs for colour view in night. 9) Video Compression (Minimum): H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 10) Wide Dynamic Range: WDR (120dB or more) 11) Digital Noise Reduction: DNR (2D/3D) On/Off 12) Streaming: Triple streaming, configurable 13) Video Streaming & Frame Rates: Triple streaming, configurable Main stream: 5/6MP @25/30 fps, Sub streams: D1@25/30 fps or better 14) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser 15) Profile Management: User configuration import, export 16) Security: User Authentication, Water Marking 17) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto 512 GB. It should be supplied with minimum 128GB memory Card. 18) Recording Management: Format SD, overwrite, storage management, video to NAS device,
19) Edge Analytics : Tripwire, Intrusion, Motion Detection 20) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection; memory card state detection; memory space detection 21) Alarm Support: It should have 1/1 Alarm In/ Out Port 22) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external Mic. and Speaker (As per site requirement) with G.711U/A/ G.711Mu/AAC/ G.726 audio compression 23) Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast, 24) System Capability: ONVIF 25) VMS: Camera shall support open source VMS 26) Cyber Security: trusted boot, AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs, , account lockout, video encryption, IP/MAC filtering, HTTPS, trusted upgrade. 27) Ethernet: 1 RJ 45 10/100 Ethernet port 28) Power Input: The camera should support simultaneous dual power input 12 VDC (via power adapter) and PoE to ensure continuous operation in the event of a failure in one power source. 29) Power Requirement: 12VDC/24VDC/PoE (802.3af)/ePoE 30) Enclosure: IP67 weather proof, IK10 31) Operating Condition: Ambient Temperature:- (- ) 05°C to 50°C, humidity 95% (max) (non-condensing) 32) IR life: 40000 hours or higher 33) Video Bit rate: 32 KBPS - 8 MBPS or better 34) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS 5MP/6MP IP IR 2.7 to 4 mm ~12 to 13.5mm or better Varifocal Motorized lens Dome Camera.
Supplying Installation Testing and Commissioning of 5MP/6 MP IP IR Bullet Camera having following specifications, type of lens and features etc :- 1) Type of Camera: Bullet Camera 2) Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night condition 3) Signal System: PAL/NTSC 4) Minimum Illumination: 0.006Lux@ F1.4, AGC ON, 0 lux with IR or better 5) Imaging: 1/3s to 1/30000s, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multizone Privacy Masking, HLC, Digital Watermarking. 6) On Screen Display: Camera should display Camera title, Date & Time in live & recorded video both. 7) Signal to Noise Ratio: > 50 dB 8) Lens Type & Focus: as given below. 9) Day & Night: True Day & Night High Performance Mechanical IR cut filter with auto switch, IR Source Inbuilt IR LED's with effective distance upto 50 Mtrs integrated IR and 30 Mtrs for colour view in night. 10) Video Compression (Minimum): H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 11) Wide Dynamic Range: WDR (120dB or more) 12) Digital Noise Reduction: DNR (2D/3D) On/Off 13) Streaming: Triple streaming, configurable 14) Video Streaming & Frame Rates: Triple streaming, configurable Main stream: 5MP/6MP @25/30 fps, Sub streams: D1@25/30 fps or better 15) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser 16) Profile Management: User configuration import, export 17) Security: User Authentication, Digital Water Marking 18) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto 512 GB. It should be supplied with minimum 128GB memory Card. 19) Recording Management: Format SD, overwrite, storage management, video to NAS device,
20) Edge Analytics: Tripwire, Intrusion, Motion Detection 21) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection; memory card state detection; memory space detection 22) Alarm Support: It should have 1/1 Alarm In/ Out Port 23) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external Mic. and Speaker (As per site requirement) with G.711U/A / G.711Mu/AAC/ G.726 audio compreesion 24) Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast, 25) System Capability: ONVIF 26) VMS: Camera shall support open source VMS 27) Cyber Security: trusted boot, AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs, account lockout, , video encryption, IP/MAC filtering, HTTPS, trusted upgrade. 28) Ethernet: 1 RJ 45 10/100 Ethernet port 29) Power Input: The camera should support simultaneous dual power input 12 VDC (via power adapter) and PoE to ensure continuous operation in the event of a failure in one power source. 30) Power Requirement: 12VDC/24V DC/PoE (802.3af)/ePoE 31) Enclosure: IP67 weather proof, IK10 32) Operating Condition: Ambient Temperature:- (-)05°C to 50°C, humidity 95% (max) (non-condensing) 33) IR life: 40000 hours or higher 34) Video Bit rate: 32 KBPS - 8 MBPS or better 35) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS 5MP/6MP IP IR 2.7 to 4 mm ~12 to 13.5mm or better Varifocal Motorized lens outdoor Bullet Camera.
Supply , installation , testing and commissioning of 5 MP PTZ Bullet camera (outdoor type) in metal body with continues 360° pan for both indoor and outdoor with 30x Minimum & 12x Digital Zoom or better,Lens 4.3-129 mm or better, Image Resolution 1920 x 1080 or better in H.264 and Motion JPEG, Day & Night, IP66 and Edge Storage Built in SD card slot with support upto 64 GB with Class 10 speed Autotracking , Mounting brackets are included.
Supply, installation, testing and commissioning of 64 Channel NVR 96 TB (12x8 TB), Total HDD slot: 8,Free HDD slot: 0,Out-of-the-box storage: 160 TB after RAID 6, hot swappable Enterprise Class HDD,Factory RAID level: 6, RAID levels: 0, 1, 5, 6, 10, Operating system Microsoft® Windows® 10 Enterprise, Operating system drive: 240 GB SSD, Recording rate up to 1.5 Gbit/s, Up to 2 x 800 W hot-plug redundant power supplies,2x USB 2.0,1x USB 3.0,2x VGA,2x iDRAC dedicated Ethernet port,2x RJ45 1 Gbps,Humidity 20–80% RH (non-condensing),10 °C to 35 °C,IEC/EN/UL 60950-1, IEC/EN/UL 62368-1, EN 62311, NOM-019-SCFI-1998,NDAA
Supply , Installation , Testing and Commissioning of 4K 65" LED Professional Display Panel, brightness:
350 cd/m2, Input/Output: 2x HDMI Input, 1xUSB, Audio Input/Outpot, Control: 1xRJ-45(Ethernet), 20 watt inbuilt speaker, 5 meter HDMI cable complete etc. as required.
Supply, installation, testing and commissioning of joy stick as per Specification with connectivity complete as required.
Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.
Supplying, Installation, Testing and commissioning of CAT6A Copper Information Outlet (IO) with face plate of color as per site requirement, should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and Components should be from same OEM to maintain compatibility and interoperability etc. complete as required.
Supply, Installation, Testing & Commissioning of Weather Proof Outdoor Enclosure suitable for LIU ,PDU & Switches.
Supplying and fixing of following sizes of PVC Flexible conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
High Side Electrical Works
11 KV HT PANEL &11 KV HT ISOLATOR PANEL Supply, Installation, Testing and Commissioning of indoor type floor mounted metal clad, 11 kV, 630A VCB 3 Way HT Panel with totally enclosed, expendable & electrically interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as per specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and closing breaker suitable for use on 11kV, 3Phase, 50Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained electrically interlocked rack in and rack out mechanism, air insulated & encapsulated copper bus bars of 630Amp capacity, breaker featured with mechanical ON/ OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 4NO + 4NC and equipped with following switchgears and accessories i/c connections suitable for 3Cx 240*sq.mm and Outgoing shall be suitable for 3Cx 240*sq.mm as mention in SLD. XLPE 11kV cable (cable entry from bottom, end termination with heat shrinkable jointing material etc. as required . (Note - Cost of end termination not included in this item.)
INCOMER - consisting of followings- 1 set 1 no's of 600 Amp. TP VCB with earth switch. 1 No. 11KV/110Volts PT Class 0.5 accuracy and 200VA burden with 1 No. VAF (0-12 kV), digital type, and protection HRC fuse for HT metering upto 15kV on incomer. 1 No. 11kV/240Volts PT Class 0.5 accuracy and 200VA burden for incomming supply. 1 No. Microprocessor based numerical relay with O/L, E/F and highset S/C protection compatible. Breaker control switch 240 V AC spring charging motor Set of ON/OFF/TRIP indicating lamps. Clear lamp for Trip Circuit healthy supply. Aux. relays for Anti Pumping & indication. Trip Circuit spervision relay. Master Trip Circuit Relay Under/Over Voltage, Under/Over Frequency Relay IDMT Earth Current and Over Current Fault Relay Digital electronic Trivector meter with RS 485 port. Dual core dual ratio 3 CTs 120/ 60/5A of 15VA burden and accuracy Class -0.5 for metering and class 5P10 for protection. BUSBAR 600Amp TP copper Bus Bar.
OUTGOING - 2 Set - each consisting following 1 no's of 600 Amp. TP VCB with earth switch. 1 No. 11KV/110Volts PT Class 0.5 accuracy and 200VA burden with 1 No. VAF (0-12 kV), digital type, and protection HRC fuse for HT metering upto 15kV on incomer. 1 No. 11kV/240Volts PT Class 0.5 accuracy and 200VA burden for incomming supply. 1 No. Microprocessor based numerical relay with O/L, E/F and highset S/C protection compatible. Breaker control switch 240 V AC spring charging motor Set of ON/OFF/TRIP indicating lamps. Clear lamp for Trip Circuit healthy supply. Aux. relays for Anti Pumping & indication. Trip Circuit spervision relay. Master Trip Circuit Relay Under/Over Voltage, Under/Over Frequency Relay IDMT Earth Current and Over Current Fault Relay Digital electronic Trivector meter with RS 485 port. Dual core dual ratio 3 CTs 60/ 30/5A of 15VA burden and accuracy Class -0.5 for metering and class 5P10 for protection.
11 KV HT PANEL (3 Way HT VCB Panel)
Supply, Installation, Testing and Commissioning of indoor type floor mounted metal clad, 11 kV, 630A VCB Isolator HT Panel with totally enclosed,expendable & electrically interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as per specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and closing breaker suitable for use on 11kV, 3Phase, 50Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained electrically interlocked rack in and rack out mechanism, air insulated & encapsulated copper bus bars of 630Amp capacity, breaker featured with mechanical ON/ OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 4NO + 4NC and equipped with following switchgears and accessories i/c connections suitable for 3Cx 240*sq.mm and Outgoing shall be suitable for 3Cx 240*sq.mm as mention in SLD. XLPE 11kV cable (cable entry from bottom, end termination with heat shrinkable jointing material etc. as required . (Note - Cost of end termination not included in this item.). Protection relays shall also includes as mentioned in SLD. 11 KV HT ISOLATOR PANEL
CHAPTER-3-TRANSFORMER 11/0.433 KV, 3 Phase, 50 Hz outdoor/ indoor mounting (Mineral oil filled)
Supply, installation, testing and commissioning of following capacity (continuous loading) BEE 5 Star rated (Corresponding Level as per BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor applications with On Load Tap Changer (OLTC) on HV side having AVR relay and Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote and manual operation of OLTC HV side in range of +5% to -15% in steps of 2.5%, having cable end boxes on HV side suitable for 3x300 sqmm XLPE cable of 11 KV grade, including bus trunking arrangement on LV side including supplying and laying of copper conductor multicore control cable from transformer to HT breaker/panel for safety tripping, complete with all accessories and safety provisions as per relevant IS Code including first filling of filtered dehydrated oil, i/c supplying and grouting of suitable M.S. Channel with all accessories and transformer shall be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI Marked and as per CPWD specifications complete in all respects etc as required at site.
The maximum flux density in any part of the core and yoke at rated voltage and frequency shall be such that the flux density with + 12.5 percent combined voltage and frequency variation from rated voltage and frequency does not exceed 1.9 Tesla. The permissible temperature-rise shall not exceed 35 dg.C for oil and 40 dg. C up to 200 KVAand 40 dg.C for oil and 45 dg. C for above 200 KVA for winding. Inside of tank shall be painted with varnish or liquid resistant paint. For external surfaces one coat of thermo setting powder paint or one coat of epoxy primer followed by two coats of polyurethane base paint shallbe used. IS: 1180 (Part 3) shall be referred to for paint thickness for normal to medium corrosive atmosphere. For highly polluted atmosphere and special application external paint work shall be as per direction of Engineer-in-Charge. Design ambient condition : a) air temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as per location of site, d) Altitude as per location/site. Noise level Shall not exceed limits as per NEMA TR
-1 with all accessories running measured as per IEC 551 / NEMAstandard. The transformer should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc. Marking Each transformer shall be provided with rating plate made of anodized aluminum/ stainless steel material securely fixed on the outer body, easily accessible,as per IS: 1180 Part-3. The entries on the rating plate shall be indelibly marked.
Fitting and Accessories : The following fittings shall be provided:- a) Two earthing terminals with the earthing symbol b) Oil level gauge indicating oil level at minimum, 30°C and maximum operating temperature; c) Air release device (for non-sealed type transformers) d) Rating and terminal marking plates; e) Silica gel breather f) Drain-cum-sampling valve (¾″ nominal size thread, IS 554) preferably steel with plug for three phase transformers; g) Thermometer pocket with cap; h) Oil filling holes having (1¼″ nominal size thread) with cover (for sealed type transformers without conservator); i) Lifting lugs for the complete transformer as well as for core and winding assembly; j) Pressure relief device or explosion vent above 200 kVA; k) One filter valve on the upper side of the tank (for transformers above 200 kVA); l) Unidirectional flat rollers (for transformers above 200 kVA); m) Inspection hole (fortransformers above 200 kVA); n) HV side neutral grounding strip (where one of the HV bushing terminal is connected to earth) o) Buchholz relay for transformers above 800 kVA. p) Arcing horns or suitable rating lightning arrestors for HT side – 3 Nos. q) Bird guard; r) Oil temperature indicator and winding temperature indicators for transformers above 200 kVA with suitable tripping mechanism above permissible limit s) Jacking pads (for transformer above 1600 kVA); t) Additional Neutral separately brought out on bushing for earthing. u) Magnetic oil level gauge (for transformer above 1600 kVA) with low oil level alarm contact; v) Non return valve (for conducting pressure test); w) Pressure relief device or explosion vent x). Monogram Plate y) Inspection cover z). Detachable type radiators with top and bottom shutoff valve. aa) Oil Conservator with Oil level indicator, minimum level marking and drain plug for all transformers of capacity 50 KVA and above. bb) Necessary hardware, clamps, lugs etc. for termination on HV/MV etc. for all transformers.
CHAPTER-4-AUTOMATIC POWER FACTOR CORRECTION (APFC) PANEL
(A) Incomers Suitable capacity MCCB/ACB (Upto 300 KVAR, MCCB and above 300 KVAR, ACB ) Microprocessor base with O/C, S/C, E/L release of TPN 50KAbreaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED Indicating Lamp set along with required Instruments and accessories with extended rotary handel and door interlocking arrangement. Current rating of the Incomer in ampere shall be APFC Panel rating in KVAR x 1.4 x 1.5 or Nearest higher standards rating.
CHAPTER-5-UPS
Online UPS- Input supply: Three Phase, Output supply: Three Phase Supplying, installation, Testing & Commissioning of of following capacity at full load (Unity Power Factor) at operating temperature 0 to 40 deg C, Relative humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot swappable (allow for the replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of moduels requird for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch alongwith provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence correction. The UPS systems offered are to be of the latest technology with Digital Control Microprocessor based for reliable operation using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design, manufacturing and inspection process should confirm to the relevant International standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while operating on battery mode and delivering quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load. (The required LC ( inductor (L) and a capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non condensing, noise level less than 60db at 1 meter distance, protections: Input Under voltage over voltage, abnormal out voltage, battery over charging, output over current, short circuit protection, battery deep discharge protection, 10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. Communication RS232/RS485/SNMP port open protocol for BMS integration, all hardware & software for iOT Communication as per approved by Engineering in charge. Required battery racks and interconnecting copper conductor cables of suitable size and connectors and all required accoseries are inclusive of the cost). This system must provide a means for logging and alarming of all monitored points plus email notification. Forced air-cooling with integral inbuilt fans with redundancy (if one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1 meter distance.
The system shall be in compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display Panel (minimum) (In-build 5 inch or more LC Display / LED ) to display : a) Input: Voltage, current, Frequency. b) Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current. d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage. f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up to 3000 events like: Over temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data: No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode of Operation /Battery Mode of Operation / Bypass feeding the load / UPS Fault /Battery charging and discharging, overload, battery voltage and battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over, Under Voltage, Over Load and short circuit, Over Temperature. The UPS should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc.
80KVA (Each Power module shall be < 25 KVA)
10KVA (Each Power module shall be < 10 KVA)
CHAPTER-6-DIESEL GENERATOR SET
Design, fabrication, loading, unloading as directed by Engineer-in-Charge, supply, installation, testing and commissioning of 3 phase 415 volts 50 cycle per second, following rating Air Cooled silent type (weather proof acoustic enclosure) DG Set 1500 RPM prime duty, radiator cooled Diesel Generator Sets. The engine shall be completed with turbo charger, flywheel to suit flexible coupling with guard, air cleaner, fuel pump, variable speed electronic governor, fuel filter, lub oil filter and pump, primary water circulating pumps, battery charger, 12/24 volt batteries of compatible capacity, MS battery stand and instrument panel comprising of switch with key, lub oil pressure gauge, battery charging voltmeter, safety control for low lub oil pressure with tripping etc. and DG controller eqv. to PCC-3.3or eqv. The DG set shall be provided with day oil tank inside the canopy as per standard capacity of the manufacturer. The alternator shall be self excited, self regulated, brushless and continuously rated at 0.8 P.F., 3 phase 415 volts, 50 cycle per second, 4 wire system and shall be provided with static excitation unit. DG set shall be compatible with Gas fuel. Dual fuel (Diesel and Gas) shall be used as fuel as per latest norms. Alternator insulation shall be class 'H' suitable to withstand tropical conditions and shall generally comply with latest upto date amendment to IS Code. The overload capacity shall not be less than 110% of rated capacity for 1 hour in every 12 hours. The DG Sets shall be mounted on a fabricated rigid common base frame with anti-vibration mountings to provide 98% vibration isolation. The DG set shall include all accessories, fittings, instruments and standard tool kit complete as per specification and as required including control cabling. The cost shall include providing and fixing adaptor box for cable termination as required.
(F) Exhaust System: Dry exhaust manifold with hospital type exhaust silencer and catalytic convertor. " (G) Starting System: 12V/24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable numbers of batteries (180 AH capacity lead acid SMF type) as required as per specifications. The battery shall be housed inside the acoustic enclosure of DG Set. " (H) Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere and the temperature rise inside the enclosure, noise level outside enclosure. The acoustic enclosure should be suitable for cable connection/connection through bus-trunking. Such arrangements on acoustic enclosure should be water proof & dust-proof conforming to IP-65 protection. The enclosure shall be as per CPCB IV + or better norms etc. and as per CPWD specifications." (I) AMF Panel: Free standing floor mounted IP 42 automatic mains fail
ure control panel including auto by-pass, suitable for KVA as below for silent type DG set complete with relays, timers, set of CTs for metering & protection and energy analyser to indicate currents, phase and line voltages, frequency, power factor, KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase & Total), KW & provision for overload, short circuit, restricted earth fault, under frequency, power (aluminum) and control (copper ) cabling of suitable size upto 15 meter between AMF panel, LT Panel and DG Set including connection interconnection etc. as required, all complete and inter locking and communication/ Ethernet /RS485/SNMP port open protocol for BMS integration including suitable software, the panel shall be of DG Set OEM make etc. as per approved by Engineering in charge and including the following:
750 kVA Diesel / Gas Generator Set
CHAPTER-15- ELECTRICAL VEHICLE CHARGER
Supply, Installation, Testing and commissioning of EV charging stationAs per specifications and in Compliance to relevant IS codes etc. Light EV AC Charger (Mode-3) Power : 7 kW, Input power supply: 1phase 230 +10% Volt, output supply: 230 Volt AC, Frequency:50 Hz +/-3%, Operational temperature range : -25 to 55 degree C (outdoor), -5 to 55 degree C(Indoor)., RH upto 95%, Charging Device as per IS-17017-22-1 EV-EVSE Communication: as per relevant IS Codes, Bluetooth Low Energy, one Charge Point Plug/ Socket as per IS60309 and IS-17017-2, Vehicle Inlet/ Connector As per EV manufacturer, suitable for 2 Wheelers and 4 wheelers. Indoor use: at least IP41; Outdoor use: at least IP44. Mechanical Strength :protection of the external enclosure against mechanical impact shall be IK08 according to IEC 62262.O/L,S/C protection. Insulation Resistance > 1 M Ω. Cable Length: 7.5 m. RCD having a rated residual operating current not exceeding 30 mA; Separate RCD for multiple outputs. Telecommunication port of the EV supply equipment according to IS 13252 (Part 1) : 2010. OCPP(Open charge point protocol) 1.6J upgradable to ocpp 2.0. Device Should follow 17017 series of IS codes in general and the installation of the system shall comply with relevent IS Codes.
MAIN LT PANEL AND SUB LT PANELS
Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of LT PANEL, fabricated out of 14 gauge CRCA sheet steel in cubicle compartmentised modular 3b construction, free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel, `T’ sections and / or flats wherever necessary. 16 gauge CRCA sheet steel shall be used for final distribution panels. 3 mm thick cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before powder coating as per specifications and final approved shade. 2 Nos. earthing terminals shall be provided for all distrtibution panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be provided in case of large panels.The Panel shall be IP-42 Protected. Approval shall be taken for each panel in the form of shop drawings before fabrication. Galvanised hardwares with zinc passivation shall be used in fabrication of panels. Incoming EDO Air Circuit Breaker
Transformer supply (1000KVA) (2 Nos.) Each have following : 1600 Amps 4 Pole Electrically operated fully drawout type air circuit breaker with ON/OFF/TRIP indicating lamps with MCB's and over current short circuit and earth fault microprocessor releases - 1 set. Intelligent multi function di
Outgoings : 800 amps TP+N EDO ACB microprocessor based, 50 KA with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 800/5 amps 15VA CT - 3 No. 800 amps TP+N MCCB microprocessor based, 50 KA with electronic energy meter (approved by SEB) with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 800/5 amps 15VA CT - 1 No. 630 amps TP+N EDO ACB microprocessor based, 50 KA with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 630/5 amps 15VA CT - 3 No. 5
00 amps TP+N EDO ACB microprocessor based, 50 KA with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 500/5 amps 15VA CT - 3 No. 400 amps TP+N MCCB microprocessor based, 50 KA with electronic energy meter (approved by SEB) with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 400/5 amps 15VA CT - 1 No. 250 amps TP+N MCCB Thermal Magnetic based, 25 KA with electronic energy meter (approved by SEB) with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 250/5 amps 15VA CT - 3 No. 160 amps TP+N MCCB Thermal Magnetic based, 25 KA with electronic energy meter (approved by SEB) with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 160/5 amps 15VA CT - 6 No. 125 amps TP+N MCCB Thermal Magnetic based, 25 KA with electronic energy meter (approved by SEB) with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos.125/5 amps 15VA CT - 1 No. 63 amps TP+N MCCB Thermal Magnetic based, 10 KA with electronic energy meter (approved by SEB) with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 63/5 amps 15VA CT - 3 No.
Notes: Load Synchronization& Load management and Interlocking shall be provided with PLC among all incomers air circuit breakers. Potential free contact shall be provided to remote starting facilities of each starter through BAS. All outgoing shall have digital Electronic energy meter RS-485 port. Wiring with space heater, thermostat and control MCB’s shall be provided all vertical sections of C/O panel. LED light shall be provide in each section of C/O PANEL Proper ventlation, cable support and Fire Barrier shall be provided. Gas supression system provision shall be provided. Suitable danger board shall be provided. Main LT Panel_as described above. -
MAIN LT PANEL
LIft Panel (Outdoor Type) Incomer 80 Amps 4 pole Thermal magnetic based MCCB 25 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 80/5 amps 15VA CT - 1 No. Ammeter and Voltmeter with 100 Amps TPN pole aluminum bus bars. Outgoing 4 Nos. 63 Amps TPN MCCB 10 KA
UPS Input panel (80 KVA) Incomer cum outgoing 160 Amps 4 pole microprocessor based MCCB 35 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 160/5 amps 15VA CT - 1 No.
UPS Input panel (10 KVA) Incomer cum outgoing 63 Amps 4 pole microprocessor based MCCB 25 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 63/5 amps 15VA CT - 1 No.
UPS Panel Incomer 160 Amps 4 pole microprocessor based MCCB 35 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 400/5 amps 15VA CT & 600 Amps TPN pole alumminium bus bars. : 3 Set 63 Amps 4 pole microprocessor based MCCB 35 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 63/5 amps 15VA CT & 600 Amps TPN pole alumminium bus bars. : 1 Set Outgoing 2 Nos. 160 Amps 4P MCCB 25 KA, Thermal magnetic based release 4 Nos. 63 Amps 4P MCCB 10 KA, Thermal magnetic based release
Ventilation Panel Incomer 500 Amps 4 pole Thermal magnetic based MCCB 35 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 500/5 amps 15VA CT - 1 No. & 600 Amps TPN pole alumminium bus bars. Outgoing 29 Nos. 63 Amps TPN MCB 10 KA 8 Nos. 32 Amps TPN MCB 10 KA
AC Panel-1 Incomer
630 Amps 4 pole microprocessor based MCCB 50 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 630/5 amps 15VA CT & 800 Amps TPN pole aluminium bus bars. Outgoing 11 Nos. 50 Amps TPN MPCB, 50 KA, with Star Delta Starter and all allied accessories as per requirement. (9 W (20HP)+2 Spare) 8 Nos. 40 Amps TPN MPCB, 50 KA, with Star Delta Starter and all allied accessories as per requirement. (6 W (2 Nos. 18HP +4 Nos. 16 HP)+2 Spare) 2 Nos. 32 Amps TPN MPCB, 50 KA, with Star Delta Starter and all allied accessories as per requirement. (1 W (14HP)+1Spare) 3 Nos. 25 Amps TPN MPCB, 50 KA, with Star Delta Starter and all allied accessories as per requirement. (2 W (10HP)+1Spare) 2 Nos. 20 Amps TPN MPCB, 50 KA, with DOL Starter and all allied accessories as per requirement. (1 W (6HP)+1Spare) Note : Rating of MPCB shall be as per Type - 2 Test.
AC Panel-2 Incomer 400 Amps 4 pole microprocessor based MCCB 35 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 400/5 amps 15VA CT & 500 Amps TPN pole alumminium bus bars. Outgoing 10 Nos. 40 Amps TPN MPCB, 50 KA, with Star Delta Starter and all allied accessories as per requirement. (8 W (3 Nos. 18HP +5 Nos. 16 HP)+2 Spare) 3 Nos. 32 Amps TPN MPCB, 50 KA, with Star Delta Starter and all allied accessories as per requirement. (2 W (12HP)+1Spare)
EV charging Panel Incomer 250 Amps 4 pole microprocessor based MCCB 35 KA as incomer with electronic energy meter with ON / OFF / TRIP indicating lights with control MCB’s with 3 Nos. 300/5 amps 15VA CT & 300 Amps TPN pole alumminium bus bars. Outgoing 17 Nos. 40 Amps SPN MCB 10 KA
SOLAR Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:-
a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 19%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. Note : Solar shall be Online integrated in main Grid. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required. Note : The contractor shall get designed suitable MS Structure GRID at terrace & parking area, for wind speed of 200 Km/hour and provide the same. Note : contractor has to supply and install all allied accessories as per site requirement to complete the job to be provided wihtout any extra charges.
External Lighting Works
LED Street light fixture, powder coated pressure die cast aluminum body (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4 5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP66,IK-10, CRI >80 , under voltage and over voltage protection,EMI EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard
complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). 50 watt
LED Flood Light, powder coated pressure die cast aluminum (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of Flood Light, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with Driver efficiency >85% Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP-66,IK-10, CRI >80 , under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle 30 deg 120deg as per the application and the project requirement deg., suitable tiltable fitting, life time (LED,Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). 150 watt
Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 4.5 metre and upto 6.5 metre
Supply of GI Pole (Above 4.5 metre and upto 6.5 metre) as conform to relevant IS Code including all allied accessories as per site requirement to complete the job.
Single Arm Pole
Double Arm Pole
Supplying of the following sizes of 1.1 kv aluminium conductor XLPE insulated and PVC sheathed armoured cable as per IS: 7098:1988 (Part‐I) with upto date amendments. 4X 10 sqmm Al .
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 10 sq. mm (28mm)
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm
BUILDING MANAGEMENT SYSTEM (BMS)
CENTRAL CONTROL SERVER Supply Installation Testing Commissioning of Central Control Server System comprising of Intel® Xeon® CPU E5-2640 x64 (or better) compatible with dual and quad core processors, Windows 11 (Professional, Enterprise, Ultimate, 64 bit), Windows Server 2013 R2 (Standard, Enterprise, 64 bit) 16 GB or more, Video card and monitor capable of displaying at 1024 x 768 resolution or better, Latest Microsoft Licence Version Operating System Loaded with MS OFFICE 2019 Professional, Word, EXCEL, Power Point, Outlook Express, Microsoft Team official version lifetime licences suitable for running BMS software complete etc. as required.
PC System Supply Installation Testing Commissioning of Client PC System comprising of PC Hardware with minimum11th Gen Intel® I7 processor CPU E5-2640 x64 (or better), compatible with dual and quad core processors minimum 3.1 Ghz and 8GB or higher RAM, Hard Drive Space of 256 GB SSD or better, Video card and monitor capable of 1920 x 1080 pixel resolution or better with Ethernet adapter (10/100/1000 Mbps with RJ-45 connector) with 2 GB or higher Graphics card suitable for BMS System complete etc. as required.
LaserJet printer Supply Installation Testing Commissioning of LaserJet printer having printing resolution 1200 x 1200 dpi, (dot/inch) or better, 21 to 30 ppm printing speed (LaserJet) complete etc. as required
LED Display Supplying, Installation, Testing and Commissioning of following size LED display (LED monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nits or better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on monitor screen and programmable with remote (remote shall be supplied with system), Key Board, Optical Mouse, etc. as required. 32 inch or larger
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 10 sq. mm (28mm)
Software for Building Management System : Supply Installation Testing Commissioning of Nesssary Software (UL listed) Packages co
AC Panel-1 Incomer
ntaining Building Management with Capability of Collection, Storage, Processing and Controlling all the Data. Software shall support Open Standard Protocols like XML, BACnet, Modbus, Lon works etc. and without the use of Proprietary Protocols, with Enterprise Level Database Like MS SQL complete Lifetime Licenced & capable to collect, store & access all points from Fire Alarm Systems, IT Systems, Automation Systems, HVAC System, Lift, Energy management, Water Management System, etc. to create & monitor historical & event data, event management data, alarm management data & reporting data, Email Alerts for Critical alarms for all the systems. The scope includes additional software required by BMS software (to enable a standard Web browser) to be resident on the DDC/client machine (manufacture-specific browsers shall not be acceptable). User log-on identification and password shall be required & a minimum three-layered security system(User interface Level, Application Level and Data Base Level) to be deployed for safety. The supplied computer software shall employ object-oriented technology (OOT) for representation of all data and control devices within the system. This data shall reside on a server for all database access (Systems requiring proprietary database and user interface programs shall not be acceptable). All components and controllers supplied under this contract shall be true “peer-to-peer” communicating devices (Components or controllers requiring “polling” by a Master / Global / Host to pass data shall NOT be acceptable). Physical connection of BACnet/MOD BUS devices shall be via Ethernet at all levels. The License must be provided by default. The BMS software shall be complete in all respect to cater the following different numbers of points managed in the installation. For Upto 500 point included
Touchscreen Color portable operator terminal Supply Installation Testing Commissioning of following sizes Touchscreen Color portable operator terminal capable of connecting to one of the controllers on the communication bus and view parameters of the complete system. The terminal should be capable of viewing /changing parameters and trends, the specified parameters as per requirement etc. as required. 7" Touch screen
DDC CONTROLLERS Supply Installation Testing Commissioning of IP Based DDC controller capable of fully “stand- alone” operation i.e. In theevent of loss of communication with other DDC’s or Control Station, they shall be able to function on their own. Thecontrollers shall consist of dual/quad core 32 bitmicroprocessors with EPROM based operating system onBACNET. The network Topology shall not allow single pointfailure. Each DDC on field level shall have embedded TCP/IP(10/100Mbps) connectivity so that it can be hooked into theLocal Area Network (LAN) provided by the client or ondedicated network . Each DDC can be accessed from theGraphical User Interface (GUI) or from a standard Webbrowser (WBI) by connecting the server alongwith inbuilt webbrowser. All controllers shall accept 230V+/- 10%, 50HzUninterrupted power supply provided by end user. Controllershall support DHCP addressing over Local Area Network(LAN) so that the static IP requirements get reduced however a single static IP shall be provided for system so that it can behosted on to internet in consultation with end user. Themicroprocessor based DDC’s shall be provided with powersupply, analoge to Digital and Digital to analoge converterswith memory and capacity to accommodate input/output (I/O)hardware points (with or without an expansion board). EachDDC should have own board and shall accept 0-10 V / 4-20mAinput signal having Minimum 20% spare capacity consideredfor expansion. Each DDC on field level should have minimum 128MB RAM & 64MB Flash memory. Following type of Allcontrollers should be mandatorily BTL approved with B-BC profile complete etc. as required. DDC Controller-Type-I (Support upto 32 Points)
EXPNSION IO MODULE Supply Installation Testing Commissioning of following type of input output (IO) expension module complete etc. as required.
I/O Module with 8 UIO channels
SOLAR Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:-
I/O Module with 8 UI channels
Enclosure for DDC Supply Installation Testing Commissioning of following sizes Powder coated wall mounted lockable and secure enclosure for DDC panel made of 16 SWG sheet steel IP -55 rated with proper internal mounting accessories for DDC such as DIN Rails, terminal block for cable terminations, well dressed for all internal cabling, ferruling, tagging etc. The DDC panels shall have power supply and connections for other peripheral equipment, switchgear protections, isolation transformer, e
arthing, relays, fuses, auxiliary power output socket & lamp etc. as required. 500X500X200 mm
Integration Unit Supply Installation Testing Commissioning following type 3rd party Integration unit to provide the interface between Ethernet LAN and the 3rd party field control devices or any other devices which need to be integrated. These shall also provide supervisory capability of functions over the devices connected to it. The purpose of using these units should be limited to integrate the devices only. The Unit must have two onboard Ethernet port, minimum 2/3 on board RS485 ports. The Integration unit should have inbuilt 4GB memory for program storage. The Unit must communicate over TCP/IP with communication speed of 10/100MBPS. The Integration unit should be capable of handling multiple protocol simultaneouslysuch as Bacnet, Modbus, SNMP restricted to single protocol. All integrators should be mandatorily BTL listed. The integration unit shall be housed in suitable size sheet steel enclosure made of 1.6mm thick CRCA sheet, lockable front door with glass, arrangement for cable entry and duly powder coated complete etc as required. Integrator for 500 Points
LED Street light fixture, powder coated pressure die cast aluminum body (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4 5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP66,IK-10, CRI >80 , under voltage and over voltage protection,EMI EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard
Field Devices Supply Installation Testing Commissioning of following Field Devices including connection etc. as required
Water Differential Pressure (DP) Switch for Pump Status.
High/Low Level Switch for Tank Level Monitoring
Air DP Switch for Fan Run Status.
Water Pressure Sensor . Accuracy:+/-0.3% FSL
Water Flow Switch
Audio Video System Commercial Proposal for 1stto 5 th Floor Conference Room [Dimension- 26.24ft (L) x 14.10ft (W) x 9.12ft (H)] / [Dimension- 25.62ft (L) x 10.41ft (W) x 9.12ft (H)] (Quantities are for 5 Conference Rooms)
Supply of GI Pole (Above 4.5 metre and upto 6.5 metre) as conform to relevant IS Code including all allied accessories as per site requirement to complete the job.
Audio Conferencing with Integrated Audio System
SITC of intregrated high impedence Class D Dual Zone Amplifier with output power of 2 x 120 W @ 70/100 V ; Frequency Response - 55 Hz - 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz) ; THD+N - ≤1 % (at full rated power); Channel Separation (Crosstalk) - ≤-60 dBV (below rated power, 1 kHz); A/D and D/A Converters - 24-bit / 48 kHz; Audio Latency - 10.4 ms - (any input to speaker output or aux output); THD <0.3% at rated power. Channel Separation ≤ –60 dBV (below rated power, 1 kHz), Dynamic range > 88 dB. Maximum Input Level : +10 dBV or better. 1 balanced page/priority input, 3 unbalanced line inputs; built in loudspaker EQs. Shall include output for expansion amplifier and remote controller (Wired) for source as well as volume control.
Supply of Ceiling microphone with automatic dynamic Beamforming technology, The beam will automatically detect the position of the person speaking and will follow the person around the room at all times. It should have 2 x Dante digital audio (Redundancy), Analog audio out (Phoenix 3-pin), and Ethernet for Control and PoE connectivity ports. The coverage of the ceiling microphone should be min 800 square feet or more. It should have a true voice lift feature to increase audio intelligibility above the ambient noise floor. It should support IT industry standards like IEEE 802.1x. It can be controlled through software that can control and monitor the microphone in any network. It should have min 100 dB SPL, 5ms latency, and min 90dBA or higher dynamic range. High-precision audio settings for maximum control, setting to exclude (min 5) and prioritize the areas of the room. It should certified from Microsoft Teams and Zoom Video conferencing applications. It should have UL 62368 certification (including UL 2043 testing and compliance) and safety certifications.
Supplying of the following sizes of 1.1 kv aluminium conductor XLPE insulated and PVC sheathed armoured cable as per IS: 7098:1988 (Part‐I) with upto date amendments. 4X 10 sqmm Al .
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 10 sq. mm (28mm)
Display System
Supply, Installation, testing and commissioning of 75" Interactive Display with Resolution of 3,840 x 2,160, Brightness (Typical) of 350 cd/m² (220 cd/m² with glass), Contrast Ratio of 4,000:1, Viewing Angle (H/V) of 178/178°, Response Time of 8 ms. with Latest Genration OPS
Supply, Installation, testing and commissioning of 13" (13.3" active area) FHD resolution 1920 X 1080, Multi touch, Battery free stylus with two short cut keys , Encryption AES 256 / RSA 2048, brightness 350 cd/m2, , Connectivity USB Type C To USB Type C, additional 2 year Warranty included
Supply, Installation, Testing and Commissioning of Push Pull Wall Mount Bracket for 55" to 86" Flat Panels, Max Loading Capacity - 50Kg
Supply, Installation, Testing and Commissioning of The conferencing processor shall have 4 mic/line inputs and 4 balanced output channels for analog audio signals, each independently controllable . The DSP shall contain 8 channels of acoustic echo cancellation (AEC), with multiple references, routable to analog and/or Dante® inputs. The DSP shall have 16 input and 16 output Dante digital audio channels, and an Ethernet connection for control and programming, integrated VoIP connection for 1 line, PTSN, USB audio and 4/8 digital output channels on an RJ-45 jack. The audio DSP shall be configurable signal processing, including : signal routing and mixing, equalization, filtering, dynamics, delay, conference room router, conference room combining, as well as control, monitoring, and diagnostic tools. The audio DSP shall control and proxy all expansion devices and other Dante endpoints. It should have following performance specs : Frequency Response-18 Hz to 20 kHz (+0.8 dB/-0.2 dB ref 1 kHz) THD+N < 0.003% @ +4 dBu (A-weighted/20 Hz to 18 kHz) Channel Separation (Crosstalk) < -105 dB at +4 dBu 1 kHz input signal Dynamic Range > 115 dB, A-weighted 20 Hz – 20 kHz, analog input to analog ou
Supply, Installation, testing and commissioning of Wireless 10" touch Panel. Should support Wi-Fi (802.11a/b/g/n/ac); dual band (2.4GHz and 5GHz); HT80 with MIMO, Bluetooth 4.2 technology, 500 nits brightness.
Supply, Installation, Testing and Commissioning of 10-Port Gigabit Smart Managed PoE Switch
Virtual Conference System
SITC of Full HD 1080p @ 60 frames per second PTZ Camera with minimum 20X Optical Zoom and FoV of minimum 57 deg, min 255 Presets.Camera should support simultaneous outputs through Ethernet, HDMI, 3G-SDI & USB 3.0, Audio In and can be controlled via RS232 & 422 In & Out & IP.Panning angle -170° ~ +170°, Tilting angle -30° ~ +90° . The tilting and panning speed of camera should be minimum 200° per second. Camera should support SRT, FreeD Protocol, PoE and Virtual USB Driver.Camera can be controlled and managed through centralised software on network. Quoted model should be BIS, CE, FCC & RoHS Certified with Test Lab Reports.
HDMI to USB-C UVC Video Capture & Camera auto Tracking device
Signal Power Management
Cable, Connector & Accessories
Supply, Installation,Testing & Commissioning of 12 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required.
Integration & Programming
SITC- Audio-Video Conferencing System Commercial Proposal for Director (HIU) Room [Dimension- 12.66ft (L) x 14.43ft (W) x 9.12ft (H)] (Quantities are for 5 Director Rooms)
Supply, Installation, Testing and Commissioning of Autoframing Videobar for unified conferencing with 6 element array microphone having Static and adaptive dynamic beam-forming, 3 exclusion zones, acoustic echo cancellation, digital noise suppression. Supported resolutions: UHD 2160p (4K), 1080p, 720p, 960×480, 848×480, 640×480, 640×360, 432×240 (30 fps), 2 x 20Watt Stereo Amplifier. True One wire connection should support video over USB. Input ports: 1 x USB-C 3.0 (displaylink enabled), 1 x Analog audio input (stereo, 3.5 mm). Output ports: 1x HDMI for display. 1 x Gbps Ethernet and built-in WiFi for enterprise management features, Built-in camera with 120° FOV diagonal, 115° FOV horizontal, 80° FOV vertical. Camera shall be Digital PTZ type with 5X digital zoom, 8 megapixel sensor, 4K resolution, Auto white balance, Auto brightness, Digital noise reduction, Easily connect a smartphone via Bluetooth connectivity to use as a standalone speakerphone or stream music.
HDMI to USB-C UVC Video Capture & Camera auto Tracking device
Supply, Installation, Testing and Commissioning of 50-inch 4K Display with UHD 4K (3840 x 2160) Native Resolution, Ultra-Slim Depth and Uniform Bezels, 4000:1 Static Contrast Ratio, 500 nits Brightness, 24/7 Duty Cycle
Supply, Installation, Testing and Commissioning of Logic Swivel Wall Mount Bracket for 32" to 55" Flat Panels, Max Loading Capacity - 40Kg
Audio Video System Commercial Proposal for 2nd Floor Training Room [Dimension- 45.93ft (L) x 26.78ft (W) x 9.12ft (H)] (Quantities are for 2 Training Rooms)
Supply of Charging set with USB charger and 2 rechargeable battery packs for handheld and bodypack transmitter. It should charge 100% battery power in max. 3 hours charging time. Maximum operating time of 12 hours. Stackable and charging is through USB-C.
Supply, Installation, testing and commissioning of 85" Interactive Display with Resolution of 3,840 x 2,160, Brightness (Typical) of 350 cd/m² (220 cd/m² with glass), Contrast Ratio of 4,000:1, Viewing Angle (H/V) of 178/178°, Response Time of 6 ms. with Latest Genration OPS
43-inch 4K Display with UHD 4K (3840 x 2160) Native Resolution, Ultra-Slim Depth and Uniform Bezels, 4000:1 Static Contrast Ratio, 500 nits Brightness, 24/7 Duty Cycle
Supply, Installation, testing and commissioning of Push Pull Wall Mount Bracket for 55" to 86" Flat Panels, Max Loading Capacity - 50Kg
Supply, Installation, testing and commissioning of Ceiling Mount Suitable for 42" to 65" Flat Panels with 3ft to 5ft (3ft Fixed & 2ft Adjustable), Max Loading Capacity -50Kg
SITC of conferencing digital audio DSP with 32-bit fixed/floating-point DSP 456 MHz/ARM Cortex-A8 600 MHz processor or better with following features and specifications are required. The DSP shall have 12 balanced inputs and 8 balanced output channels for microphone or line-level analog audio signals, each independently controllable . The DSP shall contain 12 channels of acoustic echo cancellation (AEC), with multiple references, routable to analog and/or Dante® inputs. The DSP shall have Dante digital audio networking up to 64 x64 channels, an Ethernet connection for control and programming on an RJ-45 jack and VoIP connection for 2 lines, GPIO – 5x5 expandable general-purpose contro, PSTN and USB audio and 8 digital channels on an RJ-45 jack.It shall have IT web configuration p
SITC of 1:4 HDMI splitter with 18G 4K60 4:4:4 support.The splitter should be 1 in 4 out HDMI distribution amplifier/splitter, it should support HDMI 2.0 4K@60Hz 4:4:4 HDCP 2.2 Compliant. Each output should independently support automatic down‐scaling from 4K to 1080P. tSwitcher should support multiple HDR formats including HDR10 and Dolby Vision, it should also supports PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos, DTS‐HD Master Audio and DTS:X audio formats.
SITC of Recording, Streaming & Webcasting Hardware simultaneously, Built-in 4x HDMI & IP Inputs with 4x Line Inputs, 2x HDMI Outputs. The system should be capable to record upto any four inputs simultaneously in a single frame and as well as individual sources simultaneously. Should have minimum 1TB inbuilt storage and can be connected to local NAS storage. The system should be able to support minimum 3 unicast streams.The recorded files should have the option of time and date stamp.The device can be controlled and managed through centralised software on network .Quoted model should be CE, FCC & RoHS Certified with Test Lab Reports.
Digital Podium System
Supply of Digital Interactive Podium in Metallic Frame and Wooden Top with 21.5 inch Full HD (Electromagnetic Technology) Interactive Display with Battery free Electromagnetic Pen, with Motorized Tilting of the Interactive Panel, with provision to install Gooseneck Microphone, Interactive panel, Keyboard Tray and space to store AV equipment, Interactive display with full HD resolution of 1920x1080, Technology IPS LCD, Aspect ratio16:9, Brightness 200 cd/m2, Contrast ratio1000:1, Pen Type shall be Pressure-sensitive, Battery free with reverse side eraser functionality and cordless. Top connectivity plate with HDMI, USB x 2 and Power socket for external Laptop connectivity, built-in 4 x 2 HDMI Matrix Switcher with 4K@60Hz (4:4:4, 8- bit) as well as support for 16-bit Deep Colour, HDR (High Dynamic Range), 3D content, HD audio and other features defined by HDMI 2.0 specification and Audio De-embedder for internal connectivity.
Supply of 450mm Gooseneck microphone with a programmable microphone button (Toggle on/ off, PTM, PTT, and permanent on) and a bi-color LED ring for status indication. 450mm length, condenser capsule with cardioid pickup pattern, Frequency response: 50 Hz - 20 kHz, Maximum sound pressure level: 130 dB SPL, Connectivity: XLR 3M. It should have TTL-logic output for camera control feature.
Small Form Factor PC with Keyboard/Mouse
Supply, Installation, Testing & Commissioning of AI based Full HD 1080p @ 60fps Presenter PTZ Tracking Camera with Dual Camera- one PTZ Camera for Presenter Tracking and second fixed lens Panoramic Camera. PTZ Presenter Camera should support min 20X Optical Zoom and 12x Digital Zoom with Panning range of +170 deg to - 170 deg and Tilt Range of -30 to +90 Degrees, Field of View for PTZ Camera should be min 58 Degree and for Panoramic Camera min 85 Degree, camera should support simultaneous outputs through HDMI, 3G-SDI, USB 3.0 and IP with 1x Audio In and can be controlled via RS232 and IP. Should support multiple video streams with PIP. Tracking Camera should support Everywhere Tracking, Partition Tracking, Auto Framing & Gesture Control. Should support PoE and Virtual USB Driver.Camera can be controlled and managed through centralised software on network. Quoted model should be BIS, CE, FCC , Clickshare & RoHS Certified with Test Lab Reports.
SITC of HDMI to USB Capture device with 4K resolution through your system’s USB 3.0 port with an optional HDMI loop out that supports resolutions up to 4K @60Hz. an optional HDMI loop-out that supports resolutions up to 4K @60Hz.
SITC of 8-Port POE Switch
SITC of Ceiling/Wall Mount for Camera
Supply, Installation,Testing & Commissioning of 15 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required.
VRV Units :
OUTDOOR UNIT Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load. The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building) For Cooling or Heating or Both
Per HP
10 HP to 12 HP
14 HP to 22 HP
For 35 mm outer dia x 1/2” nominal dia threaded
Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS : 6911:2017 and conforming to EN-10312 standards with V-profile and with O-ring sealing gasket of EPDM material of required dia as per dirction of Engineer-in-charge. Female Thread Connector/ Adapter
For 54 mm outer dia x 2” nominal dia threaded
INDOOR UNIT- CASSETTE TYPE Supply, Installation, Testing and Commissioning of following minimum capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with synt
hetic washable media pre-filter, fan section with low noise fan /dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room requirement in auto mode. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)
INDOOR UNIT-HIGH WALL TYPE Supply, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)
INDOOR UNIT-DUCTABLE TYPE
INDOOR UNIT-HIGH WALL TYPE Supply, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)
Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted mid high static ductable type Indoor unit equipped with washable synthetic media pre filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) High Static Ductable units (minimum 49 to 77 Pascal external static pressure)
Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted high ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) High Static Ductable units (minimum 78 Pascal external static pressure)
REFNET JOINTS / HEADER JOINTS Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs
Indoor Units
Outdoor Multi Joint
COPEER REFRIGERANT PIPING Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : Note:- Refreigernt piping Qty shall be on the actual basis as per site condition & sizes shall be as per Manufacture & Unit & requirment. Note- (1)The Copper Piping & Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration pipiare kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.
6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm
9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm
12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm
15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm
19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm
22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm
25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm
28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm
31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm
34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm
38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm
41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm
Supply,Installation,testing and commissioning of corded remote controls as per drawing and specifications
Supply,Installation,testing and commissioning of centralised Digital remote controler as per drawing and specifications
Supplying, installing, testing and commissioning control cabling cum transmission wiring of 3 core x 1.5 sqmm copper in suitable conduits between indoor and out door unit including all acesseries.
Supply and transportation of R 410A Gas for the system.
Supplying, installing, and testing of outdoor unit Structure/stand as per ODU & Manufacture requirment
DRAIN PIPE Supplying, installing, testing and commissioning, rigid PVC (Drain) heavy duty piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation.
AIR DISTRIBUTION
AIR DISTRIBUTION (FOR AIR CONDITIONING AREAS) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Note:- UV coating & Mechanical protection shall be considered for exposed ducting insulation.
Thickness 0.63 mm sheet
Thickness 0.80 mm sheet
Thickness 1.00 mm sheet
Thickness 1.25 mm sheet
AIR DISTRIBUTION (FOR AIR CONDITIONING AREAS) Supply, installation, balancing and commissioning fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.(It shall be as per BIS standards)
Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.
Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.
Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.
SUPPLY / RETURN AIR DIFFUSERS
Supplying fixing testing commissioning of supply
air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.
Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.
Supply, installation, testing & commissioning of thermal insulated Flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications.
Supply and fixing of acoustic lining of supply air duct and plenumwith 25 mm thick resin bonded glass wool having density of 32 kg/m3 , with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.
Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. Above values should have pressure rating of 25 Bar minimum. 19mm
Supplying , Installation, Testing & Commissioning of Under/Over deck insulation material Supply and fixing of 32 mm thick FR, Class O, Tri-dimensional Closed Cell chemically Cross linked Polyethylene thermal insulation material. Volume percentage of Closed Cell not less than 90%.The Nominal Density of Material Should be 28±3 kg/m³, having a thermal conductivity of 0.031 w/m°k at 40°C,mean temperature. The material shall conform to BS 476 parts 6 & 7, in a manner to be classified as ‘Class O’ and CLASS 1 respectively. Material shall be supplied with factory laminated vapour barrier as aluminium foil on one side. Water Vapour transmission rate should not exceed 0.033g/24 hrs.m² as per ASTM E 96/ E 96 M-160 and water absorption should not exceed 0.021mg/cm² as per JIS K 6767:1999. Material should be Anti fungal as per ASTM G-21.Installation Procedure to be followed as guidlines of insulation manufacturer.
HI - WALL SPLIT SYSTEMS
Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R 407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electro technical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature). Inverter Type - Cooling only
2.0 TR with 5 Star BEE Rating
DUCTABLE TYPE SPLIT UNITS- INVERTER Supply, Installtion, Testing and Commissioning of air cooled ducted split type air conditioning machine with each having a capacity and details as mentioned below suitable for operation on R 32/R-410A /R-407 Green refrigerant comprising of Scroll type compressor hermetically sealed complete with automatic capacity, safety switches, lubrication system with min 5 year (OEM) warranty for both compressor and Printed Circuit Board (PCB) , Suitable capacity squirrel cage induction motor having class 'B' insulation suitable for operation on 415 + 10% volts, 50 Hz, A.C. supply for Blower motor, Necessary drive arrangement for blower motor, Matching Air cooled condenser with necessary fittings for refrigerant piping connections, necessary structural support for mounting condensers, Microprocessor based control panel complete with accessories, machine Isolation / disconnect switch, valves and accessories to inter connect compressor and condenser including pressure testing, vacuum. Necessary starters suitable for Indoor & outdoor unit complete with O/L ,U/V, phase reversal protection, single phase preventors i/c copper conductor control and power cable and drain pipe of suitable size and length etc complete as required. The total cooling capacity/heating capacity of tested unit shall have a capacity as per relevant IS code. The lab testing reports as per IS: 8148 shall be submitted from National Accreditation Board for Testing and Calibration Laboratories (NABL) accredited as per ISO/International Electro technical Commission (IEC) 17025 standards / Central Power Research Institute (CPRI)/Electrical Research and Development Association (ERDA)with Original Equipment Manufacturer (OEM) etc. complete as per CPWD specification as required.
8.5 TR (3.2 EER)
INLINE FANS Supplying, installing, testing and commissioning of INLINE FANS suitable for installing in any position in vertical or horizontal ducts. The casing shall be double skin, internally acoustically lined and constructed of galvanised steel. The fan shall be DIDW with forward curve impeller fitted with maintenance free external rotor motor. The motor shall be suitable for 220±5% /415±10% volt single phase /three phase 50 cycles AC supply & meeting criterion as per ASHRAE standard 90.1-2010 and high efficiency (IS 12615). Quoted price shall be inclusive of electronic speed regulator and wiring between fan & speed regulator for single phase fans. In case of 3 phase fans quoted price shall be inclusive of DOL starter panel (As per motor HP meeting our parameters) with cabling between starter panel and fan. The incoming power supply to speed regulator / starter panel shall be provided by electrical contractor. Fan along with cabinet should be AMCA certified. Noise level should not exceed 65 DB at 3 meter in room condition. PCC/RCC foundation with plaster, other mounting arrangement, Anti vibration arrangement of cushy foot mountings etc. complete in all respect shall be in contractor's scope.
PROPELLER FANS Supplying, installing, testing and commissioning of direct driven PROPELLER FANS for exhaust air as shown in drawings. Each fan shall be complete with permanent split capacitor or shaded pole motor, mounting plate with light weight type PVC /aluminium impellers with aerofoil contours for high efficiency & low noise and with wooden frames & gravity louvers for weath
200 mm dia 900 RPM fan suitable for 220 ± 5% volts 50 cycles, 1 phase AC supply.
400 mm dia 900 RPM fan suitable for 220 ± 5% volts 50 cycles, 1 phase AC supply.
VENTILATION FAN SECTION Installing, testing and commissioning of AIR HANDLING UNITS (FAN SECTIONS ONLY) with double skin construction as per specificatopns, each complete with squirrel cage induction motor (mounted internally), airfoil centrifugal fan belt drive and vibrations isolators.Motors shall be suitable for 415 +- 10% volts, 50 cycles , 3 phase AC supply an static pressure shall be as indicated . Fan-motor assembly (as whole) shall be statically & dynamically balanced to grade G6.3 as per ISO-1940/AMCA 204-3. All AHUS (Fan sections) shall be suitable for outdoor duty and complete with duct flexible connections and volume control damper . In additional all supply fans (SF) shall be provided with prefilter
AXIAL FLOW FANS Supply, Installation, Testing and Commissioning of Long Casing (motor should completely accommodated inside the casing) AXIAL FANS for exhaust air suitable for installing in any position in Horizontal or vertical. Fan shall be AMCA Certified. The motor shall be of class F/H (H class wherever specified in the item, to withstand a temperature of 250 degree celcius for 2 hours) suitable for 415 V ± 10% volts three phase 50cycle, AC supply & meeting criterion as per ASHRAE standard 90.1-2010 and high efficiency (IS 12615). The fan shall be equipped with mounting bracket Inlet & outlet cone required at discharge. all normal application fans shall be provided with sound attanuators of same make as fan at inlet & outlet. Calculation of sound reduction through attenutor is to be provuded by manufacturer. The fan shall be low RPM (less than 1450 RPM) and capacities shall be as follows:-
AIR WASHER - DOUBLE SKIN Supply, installation, testing and commissioning of double skin Air washer unit with 200 mm thick impregnated cellulose paper media (Celdek pads) of imported Origin of minimum 90% efficiency, factory assembled, distribution header, GI 'B' class piping, makeup, quickfill and drain connections, Butterfly/Gate valves for Pumps, make up, drain & quickfill connections of Sump, 2 Nos. pumps of suitable capacity (1W +1 S), Y strainers and necessary fittings etc.The quoted price shall also include GI frame and supporting structure for Celdek pads, washable synthetic fibre filters (of 90% efficiency down to 10 micron) and SS(18 gauge) sump,TEFC Motor (IP:55) Control panel complete with necessary Switchgear, Starters, metering, power and control wiring between Control panel and Motor/Pump etc. & drive unit complete with Pulley, Belts, Fresh air Louvers with bird screen (GI Construction) etc as per specification & as directed by Engineer- in-charge. Suitable PCC/RCC foundation with plaster, Antivibration arrangement of cushy foot mountings etc.in all respect shall be in contractor's scope.
DRY SCRUBBER (DOUBLE SKIN)
Supply, Installation, Testing and Commissioning of Scrubber each comprising of extract air intake section, electrostatic precipitation technology, dry type air cleaner to remove oil, smoke and fumes from exhaust air, as per the Specifications. Electrostatic section shall be made of 16 gauge galvanised sheet, high bake epoxy powder coated, washable type aluminium mesh filters, stainless steel spiked ionizers to create high voltage DC field, aluminum collector plates which should be alternatively charged positive and negative with large collecting area with 14" deep cell, to work as magnet for charged smoke and oil particles. Average efficiency of 90-95% in single pass as per ASHRAE test method. Electrostatic Precipitator should be able to charge particles from 0.01 micron to 10 microns through solid state power supply. Collector cell should be of permanent type and incorporate slide out facility for easy removal for cleaning. Power supplies shall be 100% solid state UL Listed, Module of capacity above 3000 CFM shall be equipped with Pulse width modulating (PWM).The system should be fitted with interlock switch for safety . The system should allow connection to a fan section to achieve 500 FPM velocity across the air cleaner.
Operating Voltage : 220V, 50 Hz Ionizing Voltage : 12.5 to 13 KVDC Collector Cell Voltage : 6 to 6.5 KVDC Power Consumption : Not more than 50W per cell.
Supplying, installing, testing and commissioning of SISW (Single inlet single width) centrifugal fan as per specification, with statically and dynamically balanced backward curved blades, galvanized steel housing, maintenance free bearings, belt driven complete with totally enclosed fan cooled squirrel cage induction motor, centrifugal fan belt drive and vibration isolators. Motor shall be suitable for 415±10% volts, 50 cycles, 3 phase AC supply & meeting criterion as per ASHRAE standard 90.1-2010 and high efficiency (IS 12615) . Minimum 20 mm (WC) external static pressure after fan outlet.
Supply, installing, testing and comm
400 Diameter Jet Fan at Basement
Supply, installing, testing and commissioning of CO Sensors in Basements with NO/NC contacts which will operate control panels of jet fans and all the CO sensors of each zone will be configured with all the jet fans of same zone. vendor shall be quote for CO sensor suitable number required as per CFD analysis.
PLC Panel Supply, Installation, Testing and Commissioning of PLC control panel complete with all required accessories as per specification .
Fresh air louvers (with Bird screen)
Exhaust air louvers(without Bird Screen)
Timer Display Sequential Timer-single phase- Supply, Installation, Testing and Commissioning of Auto Sequencing timer controller complete with enclosure/ accessories having facility for configuration of the same as per requirement for sequenced Start/Stop for Central control.
Timer Display Sequential Timer-Three phase- Supply, Installation,Testing and Commissioning of Auto Sequencing timer controller complete with enclosure/ accessories having facility for configuration of the same as per requirement for sequenced Start/Stop for Central control.
ASSOCIATED ELECTRICAL WORKS WITH HVAC SYSTEM
40A TPN MCB with 5.0 HP Three phase DOL starter starter with overload relay and single phase preventer . Each of these compartment shall contain indicating lamp with ON/ OFF/ TRIP status for fan sections/axial fans.
40A TPN MCB with 2.0/3.0 HP Three phase DOL starter with overload relay and single phase preventer . Each of these compartment shall contain indicating lamp with ON/ OFF/ TRIP status for fan sections/axial fans.
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Tendernotice_1.pdf
PDF • 0.97 MB
RFBAnnexBuilding.pdf
Tender Documents • 2.36 MB
Otherdwgsmerged.pdf
Additional Documents • 23.28 MB
AnnexPart2.pdf
Additional Documents • 29.82 MB
AnnexPart3.pdf
Additional Documents • 10.58 MB
BOQ_77349.xls
BOQ • 1.27 MB
Download all tender documents and submit your bid