PERIODICAL SERVICES IN CERTAIN BUILDINGS AT TECHNICAL AREA AND REPAIR/MAINT OF PUMP SETS, DOSING PUMPS LT PANELS AT PUMP HOUSES AND ALLIED WORKS IN DOMESTIC AREA AND REPAIR/MAINT OF LT DISTRIBUTION SYSTEM INCLUDING REPLACEMENT OF DISTRIBUTION PANELS

Amount

Preparation of surfaces incl brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts over all decorated plastered or un plastered surfaces of wall incl cornices etc and applying one coat of white wash upto four storie build, complete all as specified and as directed.

All as per item No 1 here in before but applying two coats of white washing complete all as specified and as directed.

All as per item No 01 here in before but applying one coat of white washing on ceiling complete all as specified and as directed.

All as per item No 01 here in before but applying two coats of white washing on ceiling complete all as specified and as directed.

All as per item No 1 here in before but applying one coat of cement base paint on walls complete all as specified and as directed.

All as per srl item No 1 here in before but applying two coats of cement base paint on walls.

All as per item No 1 here in before but applying one coat of oil bound distemper on wall complete all as specified and as directed.

All as per item No 1 here in before but applying two coats of oil bound distemper on wall complete all as specified and as directed.

All as per item No 1 here in before but applying one coat of oil bound distemper on ceiling complete all as specified and as directed.

All as per item No 1 here in before but applying one coat of exterior emulsion paint on plaster surfaces of walls/ chajja/band/facia/balcony etc and walls at any type upto four storied bldg complete all as specified and as directed.(Shade - Dark Green/Camoflague/as directed)

Preparing of previously painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

All as per item No 11 here in before but applying two coats of synthetic enamel paint complete all as specified and as directed.

Preparing of previously painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

All as per item No 13 here in before but applying two coast of synthetic enamel paint complete all as specified and as directed.

Writing letters or figures (Block. Roman, Italic or Indian) exc. 15cm and n. exc. 30cm high complete all as specified and as directed.

Preparation of previously treated wooden surfaces of any description not other wise described but not exceeding 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L for preparation of old polished surface of any description, width or girth including cleaning and applying one coat of french polishing, complete all as specified and as directed.

Taking down cement plaster on brick/concrete surfaces of any description in any position incl racking out joints, hacking for key scrubbing down with water etc and removing rubbish off the premises, complete all as specified and as directed.

M&L for rendering 15mm thick in CM (1:4) on faces of brick work or conctete surfaces finished even and smooth without using extra, complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick or concrete surface finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for applying two coats of cement base paint over a coat of alkali resistence primer on wall including preparation of new surfaces of walls, complete all as specified and as directed.

M&L for applying two coats of oil bound distemper over a coat of wall primer over a coat of 1mm thick wall putty on wall including preparation of new surfaces of walls, complete all as specified and as directed.

M&L for preparation of old treated steel surfaces of roof of any description over 10 cm girth or width and applying one coat of antisol roof paint complete all as specified and directed

S&F in repairs for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm lbut n exc 10cm long for CGI/PPGI/AC roofing, complete all as specified and as directed.

Complete removal of existing treatment on walls by brooming down or steel wire brushing/scrapping down smoke shoot, moulds, moss and effervescent salt, complete all as specified and as directed.

M & L for 2mm thick wall care putty on wall, complete all as specified and as directed.

M & L for finishing walls with acrylic smooth exterior paint of required (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (Shade - Dark Green/ Camoflague/as Directed), complete all as specified and as directed.

M & L for finishing walls with textured exterior paint of required shade as approved by GE (two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm, complete all as specified and as directed.

Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and as directed

M & L for distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour as approved by GE complete as per manufacturer's specification (two or more coats), complete all as specified and as directed

M & L for disconnecting all electric and water supply connections and other related items and lifting the unserviceable VT/ Submersible pump and motor of capacity upto 20 HP, 3 phase, 415 V, 10 staging by mechanical/manual method and dismantling the column pipe line, shafts stage and keeping the same in safe custody for reuse including transportation of the defective pump set and motor from pump house to workshop for repair and back and lowering and re-installation the same on exisisting position after necessary repair including testing, complete all as specified and as directed.

M & L for dismantling the unserviceable parts and burnt out copper winding from pump and motor of capacity from 12.5 HP upto 20 HP, 3 phase, 415V, 10 staging and rewinding the motor with supper enamelled copper wire of suitable gauge including heating, varnishing, replacement of defective spare parts, re-assembling and painting the motor with two coats of supper enamelled paint and carrying out necessary tests in presence at site, complete all as specified and as directed. (Note:- (a) Spare/parts, copper winding wire will be measured & paid seperately as supply only. (b) Labour charge for fixing parts shall deemed to be included in the unit rate.

Supply only copper winding wire with supper enamelled copper wire of suitable gauge as per capacity/rating of motor, complete all as specified and as directed.

Taking down the unserviceable parts from the pump and motor of capacity from 12.5 HP upto 20 HP, 3 phase, 415 V including over hauling, servicing/cleaning throughly discharge/ suction cases, impellers, shaft and re-assembling pump carefully including servicing the motor by varnishing, insulating the motor winding , cleaning and painting the parts with two coats water proofing supper enamelled paint after preperation of surfaces manualy including repair/replacement of unservicable parts as required at site etc and re-assembling/re-installing the pump, complete all as specified and as directed. (Note:- (a) Spare / parts shall be measured & paid seperately as supply only items (b) Labour charge for fixing parts shall deemed to be included in the unit rate.

M & L for machine work to the worn out portion of motor rotor shaft of motor from 12.5 HP upto 20 HP capacity including metalling, cutting, polishing and checking the accuracy on the lath machine, complete all as specified and as directed.

M & L for machine work to the worn out portion of thrust bearing of motor from 12.5 HP upto 20 HP capacity including metalling, cutting, polishing and checking the accuracy on the lath machine, complete all as specified and as directed.

M & L for machine work to the worn out portion of submersible pump shaft of capacity above 12.5 HP upto 20 HP capacity including metalling, cutting, polishing and checking the accuracy on the lath machine, complete all as specified and as directed.

M & L for machine work to the worn out portion of gun metal impeller submersible pump of capacity upto 20 HP capacity including metalling, cutting, polishing and checking the accuracy on the lath machine, complete all as specified and as directed.

Supply only thrust bearing plate for carbon TB assembly suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only bearing bush rubber for motor shaft suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only motor shaft sleeves (stainless steel) suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only thrust bearing assembly carbon suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only gun metal bush for motor shaft suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only motor sand guard suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only oil seal suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only motor bearing housing suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only copper end ring suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only motor coupling key suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only motor coupling suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only pad for thrust bearing made out of carbon suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only stud nut stainless steel suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only circlip lock for motor suitable for submersible motor of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only gun metal bush for suction case suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only gun metal bush for discharge case suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only bearing sleeves stainless steel suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only mild steel stud for bowl assembly suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only neck ring gun metal suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only gun metal bush for stage casing suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only gun metal impeller suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only key for impeller suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only pump shaft stainless steel suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only sand guard suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only stage casing bowl suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only coupling with key for pump and motor suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only pump non return valve, cast iron suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only allen screw suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only adjustable cap (top cap) suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only half coupling suitable for submersible pump of capacity upto 20 HP, 3 phase, 415V, complete all as specified and as directed.

Cutting the worn out portion of the existing column pipe of size upto 100mm bore and threading the same thread on the same pipe by machanically, complete all as specified and as directed.

S & F mild steel column pipe, 100mm bore, heavy duty, having wall thickness 5.4mm (3.0m/1.524m long) both end threaded with one socket conforming to IS-1239 (part-I), 1979 including painting with two coats of black bitumenous paint over a coat of red oxide zinc chrome primer internally and externally (suitable for drinking purpose) including taking out old unserviceable pipe, complete all as specified and as directed.

M & L for cleaining and descaling the column pipe of 100mm bore by wire brush including painting the internal and external surface of column pipe with two coats of black bituminious paint over a coat of red oxide primer (suitable for drinking water) after preperation of old painted surfaces, complete all as specified and as directed.

M & L for cleaining and descaling the column pipe of 80mm bore by wire brush including painting the internal and external surface of column pipe with two coats of black bituminious paint over a coat of red oxide primer (suitable for drinking water) after preperation of old painted surfaces, complete all as specified and as directed.

Material and labour for flushing bore well at the site with air compressor of capacity 250PSI/1000 Cum and related accessories at least 60 hours till water discharge is free from sand and potable water and to achieve maximum discharge capacity, complete all as specified and as directed. Note: (i) Unit rate quoted under this items shall deemed to be inclusive cost of Necessary tools and equipments as required to the site of work and removing the same after completion of work.

Supply, installation, commissioning & testing of electric driven boster pump set 230Volt, 50 HZ single phase 1 HP with controller complete with base plate fixing arrangements as per manufacturer's instructions with proper arrangements and including necessary clamp, nuts, bolts, washers, reducers etc as required complete all as specified and as directed. The pressure booster system consists of a multistage centrifugal pump suitably assembled with automatic pressure control (pressure guage, pressure switch brass NRV and brass five way connector) and Pressure tank. The pressure Booster system is suitable where the main supply lines have low pressure and wherever boosting is required and wherever pressure need to be maintained. The pump will automatically switch ON/OFF to maintain the output pressure, complete all as specified and as directed. (Make-Krlosker/KSB/CRI) Note-Old u/s submersible pumpset shall be deposited to E/M store.

S & F PVC insulated, PVC sheathed, stranded copper conductor as in flat submersible water proof cable of size 04 sqmm 3 core 1100 volts grade including taking down old one, complete all as specified and as directed.

S & F in repair direct on line starter in sheet steel enclosure, type with single phase preventer, suitable for submersible pump motor of capacity 3-5 HP, 415V, 50 Hz, 3 phase, relay range 4-10 Amps, complete all as specified and as directed. (Make: L&T Cat No MU-G6DOL or equivalent model of make of Siemen's/ABB/Havells)

S & F in repair fully automatic star delta starter,in steel sheet enclosure type with single phase preventer suitable for submercible pump motor capacity 20 HP, 415 V, 50 Hz, 3 phase, relay range 20-32 Amps, complete all as specified and as directed. (Make: L&T Cat No MU-G20 HFASD or equivalent model of make of Siemen's/ABB/Havells)

S & F in repair digital display single phase, automatic motor controller with dry run in built water level controller, dry run auto reset timer, RTC based daily On/Off timer, OV/UV protection, water tank status indication, in steel sheet enclosure type with suitable for motor output 1-3 HP, complete all as specified and as directed. (Make: L&T Cat No MR-Gi (Auto) or eequivalent model of make of Siemen's/ABB/Havells)

S & F in repair single phase preventer suitable for 3 phase 415 V, 50 Hz, AC supply, complete all as specified and as directed. (Make: L&T/Siemen's/ABB/Havells)

Dismantling the unserviceable parts and burnt out copper winding from motor of capacity 3 HP, 3 phase, 415V, and rewinding the motor with supper enamelled copper wire of suitable gauge including heating, varnishing, replacement of defective spare parts, re-assembling and painting the motor with two coats of supper enamelled paint and carrying out necessary tests in presence of the Engineer-in-Charge as per IE Rule to establish functional ability/desired performance of the repaired motor to the entire satisfaction of Engineer-in-Charge and test result kept on office record duly signed by the Engineer-in-charge and contractor. (Note:- (a) New spare/parts as required for replacement of defective/ unserviceable one shall be measured and paid seperately as 'supply only').

Supply only ball bearing suitable for centrifugal pump and motor of capacity 3 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only cooling fan suitable for centrifugal pump and motor of capacity 3 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only fan cover suitable for centrifugal pump and motor of capacity 3 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only impeller suitable for centrifugal pump and motor of capacity 3 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only bush suitable for centrifugal pump and motor of capacity 3 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only shaft suitable for centrifugal pump and motor of capacity 3 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only coupling set suitable for centrifugal pump and motor of capacity 3 HP, 3 phase, 415V, complete all as specified and as directed.

Supply only impeller casing suitable for centrifugal pump and motor of capacity 3 HP, 3 phase, 415V, complete all as specified and as directed.

Repair/maintenance of decrin dosing pump and dosing system by taking down the nserviceable parts from the pump and dosing system including over hauling, servicing/cleaning throughly and re-assembling pump carefully including servicing including repair/replacement of unservicable parts as required at site etc and re-assembling/re-installing the pump complete all as specified and directed. (Note:- (a) Spare/parts shall be measured & paid seperately as supply only item in respective items in shedule. (b) Labour charges for fixing parts shall deemed to be included in the unit rate.

Supply only pump tube suitable for decrin dosing pump motor and dosing system, complete all as specified and as directed.

Supply only injection check valve 3/8 inch suitable for decrin dosing pump motor and dosing system, complete all as specified and as directed.

Supply only weighted suction line strainer 3/8 inch suitable for decrin dosing pump motor and dosing system, complete all as specified and as directed.

Supply only white suction/discharge tubing, 3/8 inch suitable for decrin dosing pump motor and dosing system, complete all as specified and as directed.

Supply, fabricating, installation, in replacement self illumnated acrylic LED sign board factory made fixed on wall/iron frame as directed letter length 30cm max up to 40cm letter thickness 5cm max up to 6cm customized design of letters back-lit signage including embedding the signage baord firmly with the wall/ MS angle frame/as per approved art work and nomenclature as given below :- Note: Nomenclature of sign board include letters/logos. Box with frame :- 25 x 25mm square pipe (18 G) frame with cross supports @ spacing not exceeding 1.0m on the box length including 20mm x 20mm MS square pipe (18 G) stifferenrs duly white enamel painted in 2 coats over a coat of zinc oxide iron primer, depth of box should not be less than 165mm. Side, top, back and bottom panels :- Made out of 24 gauge chemically treated GI Sheets duly precoated / powder coated with white MATT finish coating on both inner and outer surface. Top panel to have 24 guage precoated drip cap (fixed with pop rivet or machine moulded to shape) of 25mm on front and side to prevent damages due to rain etc. The bottom panel should be provided with access door fixed with ss screws and suitable housing for LED drivers. LED Module :- LED 12V module beam angle >=150 degrees with IP rating >= 64, 0.72 W/70 lumens per module of 3 LEDs with 7000 to 8000 K colour temperature, Make : Tridonic/Osram/Cree/GE LED configuration :- 29 LED modules per Sqm (equal division on spacing based on height of box) and one module every 0.20m on running length of box. LED power supply :- Input 230 V AC, power supply should be CPCC (Constant power constant current) of 30W/60W/120 W each. Graphics :- Graphics shall be computer plotter cut with translucent cast vinyl matching the colour specification of the installation

Dismantling cross-arms of M.S. channel or angle sections etc and removing from site, complete all as specified and as directed.

Material and Labour for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under aluminium coat and one aluminium finishing coat of paint, complete all as specified and as directed.

M& L for earthing complete with galvanised steel earth plate electrode 60X60cmX6.0mm thick, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5metres below normal ground level, connected to galvanised earth lead 25X4mm GI strip means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrial plate No. 5 connected or indicated including testing on completion including necessary excavation, earth work, pcc pit, RCC cover, funnel with watering pipe 20mm bore light grade, GI protection pipe 15mm bore light grade, complete all as specified and as directed.

Supplying and fixing in repairs earth continuity conductor or main earthing lead of Galvanised iron strip of size 25 X 4 mm, fixed on pole from existing earth test point, complete all as specified and as directed.

Supply and fix fire retardant insulated synthetic mat for LT , 1100 Volt of 2.0mm thick +/- 10% conforming to IS, tested for breakdown strength, ageing properties, insulation resistance, effect of acid, alkaline, diesel & transformer oil, leakage current test, fire test etc having the width of 1000mm +/-20mm complete as required sutable and using adhesive and alied chemical and scaling of all part s of all joints and border ends and fixing tape making good as paste near LT panel boards, complete all as specified and as directed. Make: Vardhaman/Jyothi/Cease fire/equivalent

Taking out carefully single phase submersible/centrifugal monoblock pumping set electrically driven 1 HP to 3 HP from Jackwell/open well/from concrete foundation complete with GI pipe, electric cable, dully disconnecting all electrical connections by engaging sufficient man power and including loading on vehicle, transportation to work shop and reinstalling and reconnecting the suction and delivery pipes and electric connections of the same after complition of repair, complete all as specified and as directed.

Dismantling of electric driven centrifugal horizontal pump motor of 0.5 HP to 2 HP single phase 230 volt 50 Hz, , taking out the burnt windings ,wires,cleaning and washing of slots and rewinding the same with enamalled copper winding wire of existing gauge and quantity ( as per original/ manufacturer design ) including replacement of all damaged parts like bearing, bush gland packing etc, insulating materials such as insulating sheets, insulating paper ( Type II Class "F"), insulating heat resistant sleeves, sealing compounds, varnish etc and reassembling the motor, complete all as specified and as directed.

Dismantling of electric driven centrifugal horizontal pump motor of 3 HP to 5 HP centrifugal type 3 pahse 415 volt 50 Hz, taking out the burnt windings ,wires,cleaning and washing of slots and rewinding the same with enamalled copper winding wire of existing gauge and quantity ( as per original/ manufacturer design ) including replacement of all damaged parts like bearing, bush gland packing etc, insulating materials such as insulating sheets, insulating paper ( Type II Class "F"), insulating heat resistant sleeves, sealing compounds, varnish etc and reassembling the motor, complete all as specified and as directed.

Dismantling the submersible motor 3 phase ,50 Hz ,415 volts AC of 1HP to 3HP capacity and taking out the defective Gun metal bush, thrust bearing including taking out by cutting the brunt out winding. Cleaning the winding core thorougly by scrapping/washing and make the core suitable for re-winding. Rewinding the motor with water proof PVC insulated copper winding wire of existing guage, size. Carry out necessary machine work to motor shaft all as required including necessary spares, complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exc 1.5m in depth for foundation of pole / stay, or cable trenches and getting out in soft/loose soil, complete all as specified and as directed.

Returning, filling, including spreading, leveling watering and well ramming in layers not exceeding 25cm in soft loose soil, complete all as specified and as directed.

Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and as directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 40mm dia conforming to IS, approved colour complete with fittings for cable protection, complete all as specified and as directed.

Material & Labour galvanized iron tubing 40mm bore (light grade) with all fittings for protection of cables, laid in trenches, complete all as specified and as directed. (Note:Excavation and earth work will be measured and paid separately )

Taking down/out unserviceable UG cables of any cross sectional area and connections including bricks, GI Pipes, etc of any descriptions, laid in trenches and/or fixing with walls/poles and removing from site, complete all as specefied and as directed.

Materials and labour XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross- sectional area 16 sqmm 4 core, complete all as specified and as directed. Note : Excavation and earth work will be measured and paid separately under respective items

All as per item No. 110 here-in-above but sectional area 35 Sqmm 3.5 core, complete all as specified and as directed.

M & L for pole earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm buried directly in ground vertically to depth not less than 2.25m below ground level with top edge earth plate at a depth not less than 1.5m below ground level, connected to earth lead of wire 4mm dia by means of nuts, bolts, check nuts & washers made of galvanised iron protection pipe light grade of 20 mm dia and watering pipe medium grade of 15 mm dia and filled alternate layer of charcoal or coke and salt , watering funnel with wire mesh, earth pit chamber and cover CI frame PCC (1:3:6) type C-2 all as shown in electrical plate No 3 of SSR Part I of 2009 connected to earthing test point or as directed by Engr-in-charge all specified and indicated including necessary excavation and earth work in hard / dense soil, complete all as specified and as directed. Note : GI Wire from Earth pit to pole/panel will be included in the quoted rates

M & L for horizontal boring under the road below 1m from the road surface and dia of hole not exc 100mm, with out damaging the existing road, getting out and disposal of soil to a distance not exceeding 50m from the site of work, complete all as specified and as directed.

S&F pole mounted busbar bhamber 63 Amp, 6 way of suitable size with set of 04 copper busbar and cable terminals each of heavy duty stand lock with suitable size of brass nut, bolts and washer and cable gland, fixing clamp etc F22, complete all as specified and as directed. Make : Havells cat part No IHBC006306 or equivalent model of make : L&T/ABB

All as per item No 114 here-in-above but 100 Amp, complete all as specified and as directed. Make Havells cat part No IHBC010006 or equivalent model of make : L&T/ABB

S&F VTPN prewired distribution board VTPN-DPX 160 MCCB including provision for one No MCCB 160 Amps as incomer and suitable ELCB'S/ RCBO/ SP/TP /MCBs as outgoing double door type sheet metal enclosure 415V with 250 Amps copper bus bar each phase and 2 Neutral bar, 2 Earthbar and Cable ties for Cable managementand common neutral link without MCBs with blank plate suitable for 4 way, complete all as specified and as directed. Make: Legrand IP-54-IK-09 Cat No. 5077 50 or equivalent in Schneider/ABB Note : Rates of MCCB and MCB SPN/SP/TP shall be paid seperately in the respective items of schedule.

Supply and fixing of MCCB 4 pole, 160 Amps, 16 KA, Ics=100%Icu, thermal adjustable, magnetic release, complete all as specified and as directed. Make : Legrand cat part No 4200 17 or equivalent in Havells/ Schneider

Supply & fixing MCB triple pole and neutral (TPN) of capacity 65 to 70 Amps, 415 Volts, breaking capacity 10 KA, ‘C’ series, fixed in proper position, complete all as specified and as directed. Make Cat No 4086 65 to 4086 70 of legrand/equivalent

Supply & fixing MCB single pole and neutral (SPN) of capacity 40 to 63 Amps, 240 Volts, breaking capacity 10 KA, ‘C’ series, fixed in proper, complete all as specified and as directed. Make Cat No 4086 18 to 4086 20 of legrand/equivalent

Supply & fixing MCB single pole SP of capacity 6 to 32 Amps, 240 Volts, breaking capacity 10 KA, ‘C’ series, fixed in proper position, complete all as specified and as directed. Make Cat No 4085 87 to 408595 of legrand/equivalent Note:- An amount of Rs.35004.00 on account of credit schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S ANIL KUMAR BAUL

M/S. VINITA CONSTRUCTION

MAA TARA TRADING

M/S. KUMAR CONSTRUCTION CO.

M/S ANNI ENTERPRISE

MAJUMDER ENTERPRISE

M/S RATHIN ENTERPRISES