REPAIR TO INTERNAL ROAD, FOOTPATH, BERMS, DRAIN COVER AND CONNECTED ITEMS IN AOR OF AGE B/R-II OF GE (EAST) AGRA

Repair to pot holes any depth, not exc. 1 Sqm each including sweeping free from dust and mud or water scoring sunken surfaces in roads, paths but making good by applying tack coat @ 5 kg / 10 sqm putting permixed bituminous macadam well ramming and sealed with binder 9.8 kg per 10 sqm blended with 0.09 cum of stone chipping 6.3 mm size and again well rammed (including supply premixed macadam binder and chipping) depth of pot holes exc. 30 mm complete all as specified and directed.

M&L for preparation existing black top surface by brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surfaces with gunny bags or using air ocmpressor to remove all loose dirt etc & applying evenly a primer tack coat with bituminous primer using paving bitumen of grade VG-10 at the rate 5 Kg per 10 Sqm for laying premixed bituminious macadam premix carpet complete all as specified and directed.

M&L for premix bituminous macadam (Design mix) (consolidated thicked 75 mm or less) with 4% binder content using paving bitumen VG-30 grade by weight of total mix laid and rolled and compacted to required camber and gradient with 8 to 10 tonne vibratory road roller complete all as specified and directed. Note :- (a) Premix concrete shall be mixed in hot plant, transported from plant to work site and laid / spread by means of mechanical sensor paver. (b) Contractor shall quote his rate on the basis of binder as mentioned in above item if there is any variation in the actual binder content used in lower side, the rate shall be adjusted @ Rs.45/Kg. However no price adjustment shall be made if the binder content works out to more than as specified above.

M&L for laying bituminous premix asphaltic semi dense concrete (Design mix) 30 mm consolidated thickness with 5.5% binder content by weight of total mix, (Paving bitumen VG-30) rolled and compacted with 8 to 10 tonnes vibratory road roller to required camber and gradient complete all as specified and directed. Note :- (a) Premix concrete shall be mixed in hot mix plant, transported from plant to work site and laid / spread by means of mechanical sensor paver. (b) Contractor shall quote his rate on this basis of binder as mentioned in above item if there is any variation in the actual binder content used, the rate shall be adjusted @ Rs.45/Kg lower side of binder used. However no price adjustment shall be made if the binder content works out to more than as specified above.

Supply and fix in repair solar cat eye aluminium alloy shall (100% water proofing design according to IP 67) of size 125 mm x 125 mm x 25 mm (shank 65 mm) of high efficiency mono crystalline solar panel 2.4 V / 0.3 watt one Ni-mh or NI-cd rechargeable battery (1.2 V / 1600 MA) consisting of 06 Nos super bright LED with 10000 to 18000 mcd as per manufactures instructions complete all as specified and directed.

M&L for providing and applying 2.5 mm thick road marking strip / line (retro-reflective) of specified shade / colour using hot thermolplastic material with glass beads by fully / semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispensor, propane tank heater and profile shoe heater, driven by experienced operator on road surface incl cost of materials labour T&P, cleaning the road surface of all dirt, seals, oil grease and foreign mateiral etc complete as per direction of Engr in charge and accordance with applicable specification complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exc. 15 cm thickness (above or below ground level) etc complete all as specified and directed.

M&L for hard core of broken stone or boulder having gauge n. exc. 63 mm, deposited, spread and levelled in layers in exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick cement concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) in sub base of flooring / hard standing finishing surface even and rough using broom finish complete all as specified and directed.

M&L for provding and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawn, drive ways or light traffic parking etc of required strength thickness & size / shape made by table vibratory method using PU mould laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand, compacting and proper embedding / laying of interlocking paver blocks into the sadn bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for provding and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawn, drive ways or light traffic parking etc of required strength thickness & size / shape made by table vibratory method using PU mould laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand, compacting and proper embedding / laying of interlocking paver blocks into the sadn bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Dismantling of interlocking tiles of any size / thickness in floor / pavings in any depth etc complete all as specified and directed.

M&L for 25 mm thick sand cushion layer of laying of interlocking tiles / pavers complete all as specified and directed.

Refixing of old interlocking tiles 60/80 mm thick in floors / paving etc complete all as speciifed and directed.

Demolition of PCC kerb stone any size and shape any description and in any position complete all as specified and directed.

S&F for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement 2 coarse sand) incluidng making with or without grooves (thickness of joints except at sharp curve shall not to more than 6 mm) including making drainage opening wherever reqired complete all as specified and directed.

Refixing of old kerb stone of any thickness in any depth, jointed with cement mortar 1:3 (1 cement 3 coarse sand) including making joints with or without grooves etc complete all as specified and directed.

Taking down cement plaster on brick stone walls etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendeirng 10 mm thick in CM (1:4) on fair faces of brick work or concrete surface and finishing surface even and smooth without using extra cement etc complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying three coat of white wash complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489 : 2004, Alkali & fungel resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over weather proof 2 mm thick putty on new surfaces complete all as specified and directed.

S&F TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489 : 2004, Alkali & fungel resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over weather proof 2 mm thick putty on old surfaces including preparation of surfaces etc complete all as specified and directed.