PROVN OF SUB GUARD ROOM AT MUTAGA CAMP AND SENSOR BASED LIGHT CONTROLLED SYSTEM Ph I UPGRADATION OF EXTERNAL ELECTRICAL NETWORK FOR STATION AUDITORIUM AND MINOR WORK AT ATS BELAGAVI

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard and dense soil

Earthwork excavation over areas not exceeding 1.5m depth for foundation etc, and getting out in hard/dense soil all as specified and directed

Earthwork excavation over areas exceeding 1.5m but not exceeding 3.0m depth for foundation etc, and getting out in hard/dense soil all as specified and directed

Earthwork excvation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc or shefts , wells , cess pits, manholes etc n exc 10sqm on plan and n exc 1.5m in depth and getting out in hard/dense soil all as specified and directed

M & L Plain Cement Concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete all as specified and as directed

M & L TMT bars reinforcement 10mm dia and over cut to lengths, bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia all as specified and as directed

M & L TMT bars reinforcement 6mm to 8mm dia cut to lengths, bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia all as specified and as directed

All as per item No 7 herein before but 5mm and over upto and including 10mm dia TMT bars as in stirrups, spaces and binders all as specified and as directed

M & L Form work to sides of Concrete foundation, footings, bases of columns, raft beams and soffits of foundation and plinth beam and similar work vertical or to batter etc with fair finished flat surfaces of concrete all as specified and directed

M & L Formwork to sides of pillars, posts, struts, column or similar items rough finishes flat surface of concrete all as specified and directed

M & L Reinforced Cement Concrete, Design mix M-25 using 20mm graded stone aggregate as in foundation, including rafts, footings, plinth beams, bases for columns etc and mass concrete all as specified and directed

M & L Reinforced Cement Concrete, Design mix M-25 using 20mm graded stone aggregate as in columns, pier pillar or similar items all as specified and directed

M & L Formwork for sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels exceeding 1.5m clear span, cantilevers, shelves inlcuding supports overhangs, etc also splays between floors and beams etc. complete all as specified and directed

M & L Formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similar work not exceeding 200mm thick (horizontal or sloping) rough finished flat surfaces all as specified

M & L Formwork to edges of concrete roof slab exceeeding 10 cm but not exceeding 20 cm thick, rough finished flat surfaces etc complete all as spesified and directed.

M & L Reinforced Cement Concrete, Design mix M-25 using 20mm graded stone aggregate as in beams, cantilevers, bressumers, Lintels over 1.5 m span etc all as specified and directed.

M & L Reinforced Cement Concrete, Design mix M-25 using 20mm graded stone aggregate as in floor or roof slab supported on walls, beams and columns in floors,roofs landing or similar items all as specified and directed

M & L Pre-cast Cement Concrete 1:3:6 using 20mm graded stone aggregate as in solid block masonry exceeding 10cm in width and setting in cement mortar 1:4 complete all as specified and directed

M & L Plain cement concrete 1:3:6 using 20 mm graded stone aggregate, type C-1 as in Coping / cill, bed plates, fixing of hold fasts etc all as specified and directed.

Returning filling in including spreading leveling and well ramming in layers not exceeding 25 cm thick all as specified and directed.

Removing excavated material to a distance exc 250m but not exc 500 m and depositing Outside MoD land at a level not exc 1.50m from starting point all as specified and directed.

M & L Moorum filling under floors or in foundation, including watering and consolidation etc all as specified and directed

M & L Hardcore Broken stone or boulders of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15cm thick, watered and rolled/ rammed to a true surface all as specified and directed

M & L Plain Cement Concrete 1:3:6 using 40 mm graded stone aggregate, type C2 as in 75mm thick sub base to flooring & plinth protection etc all as specified and directed

M & L rendering 15 mm thick cement mortar 1:4 concrete or brick wall surfaces, finished even & smooth without using extra cement all as specified and directed

M & L applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as specified and directed

M & L Rendering 10 mm thick cement mortar 1:6 over concrete or brick wall surfaces finished even & smooth without using extra cement all as specified and directed

M & L preparation of new plastered wall, pillasters, cornices, etc and applying two coats of oil bound distemper over a coat of self primer including 3mm thick wall care putty all as specified and as directed.

M & L Rendering 5 mm thick cement mortar 1:3 over concrete ceiling surfaces finished even & smooth without using extra cement all as specified and as directed.

M & L preparation of new plastered ceiling surfaces and applying three coats of white wash all as specified and as directed. .

M & L Ceramic tiles, Non skid coloured, 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.16 sqm in floor with rectified edges ( joint free) etc set and jointed in neat cement slurry over cement screed 15 mm thick 1:6 cement mortar all as specified and as directed.

M & L Ceramic tiles, coloured glazed of size 450 x 300 x 7 mm thick with rectified edges as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including backing coat 10 cm thick cement mortar1:4 all as specified and as directed.

M & L Kota stone slab flooring 20-25mm thick, machine cut over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete set and jointed in neat cement slury over cement screed 15 mm thick cement mortar 1:6 all as specified and as directed.

M & L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement base and jointed including rubbing and polishing etc complete set and jointed in neat cement slury over and including backing coat 10 cm thick cement mortar 1:4 all as specified and as directed.

Supply only liquid water proofing compound all as specified and as directed.

M & L Pressed steel frames for doors with one or more rebates, size of frame 125x60mm, including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed

M & L Flush shutters 30mm thick, solid core construction, with particle board core and plywood face panels commercial type on one face, deco rative face veneer on other side including lipping/frame to match with kiln seasoned and chemicaliy treated all as specified and directed

M & L second class hardwood glazed and skeleton shutters, 30 mm thick open rebaed and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze etc; sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkats all as specified and directed

S & F Steel windows / ventilators with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, for securing wire mesh dovetailed or welded complete all as specified and directed

S & F Steel windows /ventilator with side hung shutter including projecting type hinges with steel handle and steel peg stay with glazing bars for securing glass panes, dovetailed or welded complete all as specified and directed

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws all as specified and directed

S & F figured glass pin head type 3 mm thick and glazing with oil putty in square not exc 0.5 sqm in each pane all as specified and directed

M & L sheet glass, ordinary quality 4 mm thick and glazing with wooden beading, not exc 0.5 Sqm in each pane all as specified and directed.

S & F Aluminium alloy, anodised, 300mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy all as specified and directed.

S & F Aluminium anodised, barrel tower bolts 200mm long of extruded section all as specified and directed.

All as per item No 45 herein after but 100 mm long

S & F butt hinges,100 mm long, medium weight cold rolled M S all as specified and directed.

S & F Extruded aluminium alloy handles, fabricated type, 150mm size anodised all as specified and directed.

S & F Floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece fixed in floor, over all length of cover plate 140mm all as specified and directed.

M & L preparation of new wooden surface and applying two coats of synthetic enemal paint over a coat of pink primer complete all as specified and directed.

M & L Preparation of new steel surface and applying two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed.

S & F 25mm dia decorative type stainless steel curtain rails with decorative type fixing brackets, stops, rollers etc. all as specified & directed

S & F 25mm dia decorative type brackets for stainless steel curtain rail including stops, rollers etc. all as specified & directed

Supply, Hoisting and fixing 500 Ltr capacity rotational moulded polyethylene water storage tank, cylinderical vertical, with closed top hoisted and fixed in position all as specified in SSR part I including set of ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 25 mm dia ferrule all as specified & directed

M & L High density polyethylene pipes (HDPE) 40mm dia bore, pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors as drain out pipe etc all as specified & directed

M & L Cement concrete 1:2:4 using 20mm graded stone aggregate, type B-1 as in coping with necessary form work including finishing even and smooth without using extra cement to exposed surface all as specified & directed

M & L Powder coated (minimum thickness of powder coating 50 micron) aluminum frame for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified & directed

S & F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side or top hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long, hinges type B-21, 100mm long suitable handle complete all necessary fittings as specified.

S & F sheet glass 4.8 mm thickness, ordinary quality, in squares exceeding 0.5 sqm each pane including solar control film 50micron reflective type sticking to glass pane all as specified and directed

M & L Granite work 20mm thick(table rubbed polished ) for wash basin tops and similar items in cement mortar 1:4 including pointing in white cemnet 1:2 using marble dust with admixture of pigment to match with shade of granite laid over15mm thick screed bed in cement mortar 1:4 all as specified & directed

Supply and fix the following sanitary items altogether all as specified & directed. :- (i) vitreous china wash down water closet pan, pedestal pattern, white (ii) PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet, ball valve, float and handle including brackets and flush pipe (iii) Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device (iv) Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & F Vitreous China wash basin, angle back, size 550x400mm, white, including cutting for and pinning in ends of brackets or erecting stand all as specified and directed

S & F Grating doom PTMT 125 mm dia with waste hole (Minimum weight 40gms) all as specified and directed

S & F Bib taps 15mm, brass chromium plated, round handle, screwed down, screwed for iron pipe all as specified and directed

S & F Pillar taps, brass chromium plated 15mm, round handle, screwed down, screwed for iron pipe all as specified and directed

S & F Stop valves, brass chromium plated, 15mm screwed down, high pressure, with crutch or round handle screwed bolts ends for iron pipe or for unions all as specified and directed

Supply and fix Fancy type square shape PTMT swivel shower fixed to 15 mm ferrule all as specified and directed

S & F tubular Towel rail 20 mm dia, D type 60 cm long between flanges, brass chromium plated all as specified and directed .

S & F PVC connection 15mm size 450mm with PTMT nuts all as specified and directed .

S & F PVC (SWR) pipes 75 mm dia, single socketed in any length with rubber ring joints, fixed on wall/ floor with necessary clamping where required all as specified and directed .

All as per item No 71 herein before but 110 mm bore pipe

S & F floor trap (SWR) plain with grating 75 mm dia outlet including jointing with solvent all as specified and directed

S & F PVC bends any radius 75 mm bore all as specified and directed

S & F PVC bends with access door 110 mm bore all as specified and directed

S & F PVC (SWR) vent cowl 110 mm dia bore all as specified and directed

S & F Soap dish, brass chromium plated all as specified and directed .

Supply and laying galvanised iron Tubes, medium grade, 15mm bore, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

All as per item No 78 herein before but 20 mm bore

All as per item No 78 herein before but 25 mm outer dia

M & L Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10cm but not exc 20 cm girth in block masonry walls all as specified and directed

M & L rendering 10 mm thick in cement mortar 1:3 mixed with (conplast-X 42 11 C fosroc chemical (India) Ltd) liquid water proofing compound 100 ML per bag of cement as specified by manufacturer instruction on concrete surfaces of roof and making the surfaces finished fair and even as required slope for draining out the rain water all as specified and directed. Note - WPC (conplast-X 42 11 C fosroc chemical (India) Ltd measured and paid separately

M & L Preparing RCC roof slab by removing dust, dirt and applying oil based bituminous primer @ 0.2Kg/Sqm and providing APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) on primed surface by forced application including minimum 10cm side over laps and 15cm end lap torch sealed and bonded and applying a coat of blown hot bitumen 95/15 over a membrane at 1.20 kgs/sqm all as per detailed specification and procedure all as specified and as directed.

Apply a coat of solar reflective bituminous aluminium paint over APP membrane on roof top surfaces at 0.10 kg/sqm all as specified and as directed.

M & L Machine cut cudappah stone slab 20-25mm thick as in shelf slabs over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed

Rounding to edges of stone slabs one edge, such as in steps, shelf slabs, platform, and other similar situations all as specified and directed

M & L Anti termite treatment to the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) all as specified and directed

M & L Anti termite treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface all as specified and directed

M & L Anti termite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area all as specified and directed

M & L Anti termite treatment Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall all as specified and directed

Grubbing up tree trunk including cutting of trunk portion protruding over ground, digging out roots, filling holes and levelling off ground, stacking of servicable materials and removing of unserviceable material to a distance not exc 50m and clearing site girth of tree exc 30cm but not exc 100cm roots and directed

Demolition of plain cement concrete in ground floors and pavings not exc 15cm thickness(below or above ground level) all as specified and directed

M&L for 100mm thick PCC 1: 4:8 type D2 using 40mm graded stone aggregate as in sub base of flooring all as specified and directed

M & L Glass dividing strips, 3 mm thick 38mm wide all as specified and directed

M & L Sand filling under floors or in foundations including watering and consolidation all as specified all as specified and directed

M&L for Machine pressed precase concrete interlocking paver block any shape and size conforming to IS-15658-2006 of 60mm thickness, Rubber moulded M-35 grade with grey cement and pigment all as specified and directed

Precast cement conceret in PCC 1:2:4 type B1 using 20mm graded aggregate as in kerb stone finished smooth using extra cement including necessary mould/form work and jointed in CM 1:4 struck flush with same mortar all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as directed.

M & L Pre cast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slab and set in cement mortar 1:4 all as specified and directed NOTE: Reinforcement shall be measured and paid separately.

M & L Mild steel round bars Fe 290 (Gde -E-165)10mm dia and over, cut to length, bent to shape required, including cranking, bending including binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed

M & L Plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in concrete bed to drain pipes 150mm bore including packing under and haunching against the sides including testing all as specified and directed

M & L Re-inforced concrete pipe of 150mm dia, class NP-2 laid and jointed complete with collars all as specified and directed

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc

Supply only integral water proofing compound.

Excavating in trenches not exc 1.5m wide and not exc10sqm on plan for foundation and exc 1.5m and not exc 3m in depth getting out in Hard/ dense soil

Reinforced Cement Concrete, Design mix M-25 using 20mm graded stone aggregate as in wall, retaining walls, basement walls all as specified & directed

M & L Plastering 15 mm thick in cement mortar 1: 4 including mixing water proofing compound and finishing the surface even and smooth without using extra cement Note: WPC will be measured and paid seperately)

M & L Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter fair finished flat surfaces all as specified & directed

Dismantling wrought iron or mild steel work, barbed wire of any description not other wise provided for including stacking, loading etc all as specified and directed.

Demolition of cement concrete or other wise specifically provided for all as specified and directed.

Demolition of cement concrete (reinfoced) or other wise specifically provided for all as specified and directed.

Cutting holes exc 250sqcm but not exc 500sqcm into or through reinforced cement concrete slabs, chajjas, beams, walls etc. including cutting of reinforcementetc complete all as specified and directed.

M & L Cement concrete 1:2:4 using 20mm graded stone aggreagate in holding angle pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) all as specified and directed.

S & F mild steel angles, flats in posts and struts in fencing including cutting tops to shape as directed drilling holes notching for wire etc flat iron fillets including all necessary drilling, blocking or reveting etc all as specified and directed..

S & F GI barbed wire 2 strand 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standards rails including securing or tying at crossings with and provision of galvanised steel wire staples etc all as specified and directed..

M & L Preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

Supply and fixing concertina coil fencing, punched tape, coil 600 mm dia having 7 to 8 nos rounds per 1 metre length, fixing on angle iron 'Y' shaped & placed 3 m height wall with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, etc complete all as specified and directed.

M & L preparation of new plastered wall surfaces and applying two coats of cement paint over a coat of alkali resistant primer all as specified and directed.

M & L bituminous Board filler 25 mm thick (Avg Thickness) in crumple joints of Security wall all as specified and directed.

M & L Plain aluminium sheeting 0.56 mm, in ridges, hips, valley gutter, over crumple joints and straight flashings (length and girth fixed) all as specified and directed.

M&L PCC 1: 4:8 type D2 using 40mm graded stone aggregate as in 75mm thick sub base of flooring all as specified and directed

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in 100mm thick flooring finished even & smooth without using extra cement all as specified and directed.

M & L Rolled mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410W (Gde E-250 quality A) all as specified and directed.

M & L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to all as specified and directed.

M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 all as specified and directed

M&L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410W (Gde E-250, Quality -A) all as specified and directed.

M & L Preparation of new wall surfaces and apllying two coats of cement base paint over a coat of self primer all as specified and directed.

Supply and fix Dual Mounting PASSIVE INFRARED Sensor with good sensitivity detector, integrated circuit, Power source 220 V AC-240 Volt AC, Power frequency 50 Hz, Ambient Light <10 LUX-2000 LUX (Adjustable), Time delay minimum 10 S +-3 S, Rated load 1000 W & Detection Distance 8 Mtr maximum etc complete all as specified and directed

Material and labour sub main wiring with two single core FRLS PVC insulated multi stranded copper conductor cable 1100Volt grade 2.5 sq mm drawn through and including suitable size of non-metallic PVC conduit / PVC casing and capping and accessories fixed on walls, roofs or floors including one run of 2.5 sqmm FRLS PVC insulated multi stranded copper conductor cable 1100Volt grade as earth continuity conductor cable and connecting up to earth dolly for controlling of building security light complete all as specified and directed Note : Three runs of 2.5 sqmm copper conductor and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

M & L Low Tension under ground cable of size 16 x 4 sqmm cross sectional area, XLPE insulated, armoured heavy duty electric aluminium conductor 1100 Volts grade laid in trenches / passing through pipes all as specified and directed

M & L for LT Cable route indicator with a welded/riveted disc of 100mm dia and engraved with cable route marker fixed on angle iron 40 x 40 x4 mm grouted in PCC 1:3:6 type C1 using 20mm graded aggregate at approx distance 100 mtr including necessary earth work excavation, removing complete all as specified and directed

S & F of double walled corrugated HDPE Pipe IS-16205, size inner dia 95mm, outer dia 110 mm for cable protection in wall/under gorund laying of UG cables including SNAP-FIT Coupler and all fittings as required at site complete all as specified and as directed

M & L Cutting the tar macadam road / hard standings for laying cable and excavating not exe. 0.45m wide and 0.60m in depth and getting out and filing back with PCC 1:4:8 type B-2 including finishing complete all as specified and as directed

M & L Galvanised Iron pipes 40mm dia bore, light grade with all fitting and fixed to poles/route/drains, ceillings or laid in floors complete all as specified and as directed

S & F sheet metal enclosure factory made double door for TPN DB 4 Way with 200 Amps rated bus bar 415 Volts suitable for fixing MCB TPN 6-32 Amps main incoming complete all as specified and as directed. Note : MCB TPN 6-32 Amps will be measured and paid seperately under relevant item of this schedule.

S & F MCB triple pole & neutral, 415 volts, 6 to 32 Amps, 10KA rupturing capacity complete all as specified & directed.

M & L MCB Single Pole,C Series, 06 to 32 Amps, 240 volts, 50 Hz AC supply complete all as specified & directed.

M&L for Earthing with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 5 of SSR Part-I and testing on completion all as specified & directed.

Supply and fix galvanised iron water tubing, 40mm bore, 'medium grade' with all GI fittings such as bends, elbows, tees, connectors, short pieces, back nuts, unions, caps & plugs etc laid in trenches including cutting, threading and testing complete all as specified and as directed

All as per item No 139 herein before but 25mm bore

Supply and fix Galvanised iron water tubing 25mm bore 'medium grade' with all GI fittings such as bends, elbows, tees, connectors, short pieces, back nuts, unions, caps & plugs etc fixed to wall and ceiling or laid in floor including cutting, threading and testing complete all as specified and as directed.

Supply and fix Gun metal globe or gate valve (ISI marked), with iron wheel head, screwed both ends, suitable for 25 mm bore iron pipe and fixed including testing complete all as specified and directed

Supply and fix Gun metal globe or gate valve (ISI marked), with iron wheel head, screwed both ends, suitable for 40 mm bore iron pipe and fixed including testing complete all as specified and directed

Construction of Valve chamber with inner dimension of 600 mm x 600 mm x 600 mm with 150 mm thick PCC 1:4:8 type D-2 in foundation, 230 mm thick brick wall in cement mortar 1:4, PCC 1:2:4 type B-1 in coping, rendering 15 mm thick both internal and external surfaces in cement mortar 1:4, including provision of mild steel sheet 3 mm thick cover fixed on mild steel angle 40 mm x 40 mm x 6 mm frame work, all iron surfaces painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including handle, necessary excavation and earth work in hard/dense soil complete all as specified and as directed.

M & L Cutting the existing pipe upto 80mm GI & inserting & including the TEE for taking branch connection complete all as specified and directed

M & L Point wiring with PVC insulated and unsheathed multi stranded 1.5 Sqmm FRLS copper Cable drawn in and including PVC casing capping of suitable size not less than 25mm width with all accessories including MS sheet metal 1.2mm thick switch board or PVC rectangular switch board of suitable size to be fixed on wall including PVC insulated and unsheathed multi standard 1.5 Sqmm FRLS copper Cable as earth continuity connected with common earth dolly complete all as specified & directed for following :-

One light/fan/bell point controlled by one switch

One 3 pin switch socket outlet, 5 Amps, independent

One 3 pin switch socket outlet, 5 Amps on the same board with other switches

All as per item No 146 herein before but one 3 pin socket outlet 15 Amps independent with cable 2.5 sq mm size

Supply and fix switch piano, flush type single pole, one way 5 Amps, 230 volts all as specified

M & L Ceiling rose, surface backelite, three terminal 240 volts complete all as specified & directed

Supply and fix switch socket outlet, 2/3 pin, 5 Amps flush type all as specified & directed

Supply and fix switch socket combination multipurpose 2 in 1, 3 pin 5 /15 Amps universal type controlled by one switch all as specified & directed

Supply and fixing ceiling fans with blades, down rods, electronic regulator and accessories, 230 Volts, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC), cable 3 core of size 0.5 sqmm from ceiling rose to fan, including writing MES No in 2cm height with synthetic enamel black paint complete all as specified and as directed.

Supply and fix Exhaust fan of size 300 mm sweep, heavy duty, 1400 RPM connecting with cable 3 core of size 0.5 sqmm from ceiling rose to fan, with louver including writing MES No 2cm height with synthetic enamel black paint all as specified and directed.

S & F Wall mounting fan, 400mm sweep, 1350 RPM suitable to AC single phase 230/240 volts with speed and swing adjustment fixed to wall with bolt/screws complete as specified and directed.

Supply & fixing in regal batten with one LED tube 20 watt for fixing LED tube 20 watt , T-8 complete all as specified & directed.

Supply & fixing surface and wall mounted LED batten 9/10 watt LED LUMILIN with polycarbonate housing and integrated electrnic driver all as specified and directed.

S&F security light 20 Watt LED building mounted, new generation energy saving and environmental friendly long life, made up of pressure die cast aluminium housing with high efficent LED as lighting source and PC cover having TOP Opening, seperate driver compartment with IP66 protenction and impact resistance of IK07 complete all as specified and directed. .

Supply, laying and testing LT cable XLPE insulated, stranded aluminium conductor of size 120 Sq mm 3.5 Core, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with complete all as specified and directed.

S & F of DWC pipe IS-16205, size inner dia 103mm, outer dia 120mm for cable protection in wall / under ground laying of UG Cables including SNAP-FIT coupler and all fittings as required at site complete all as specified and as directed

M & L G I pipes 80 mm dia, light grade with all fittings and fixed complete to poles, walls, drains, ceiling or laid in floors complete all as specified and as directed

M & L Earthing and testing complete with galvanised iron earth plate electrode 60cm x 60 cm x6mm thick directly in ground vertically to a depth not less than 2.25m below normal ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to and including G I strip 25X4 mm as earth lead by means of bolts abd nuts, check nuts and washers etc made of GI & connected to equipment and earthing test point, earth dolly all as shown in earthing plate No 3 of SSR Pt-I including all necessary earth work excavation, PCC 1:2:4 chamber & cover with handle and 20mm dia GI watering pipe and 40 mm dia light grade GI for protection of earth strip, wire mesh, funnel, charcol dust & common salt, etc all as specified and directed and testing on completion all as specified and as directed.

Supply and fix G I strip 25X4 mm buried in ground all as specified and as directed.

Supply and fix in repair single pole and neutral enclosure with two pin and earth plug, socket complete with one single pole MCB 20 Amp all as specified and directed

S & F sheet metal enclosure, factory made, double door for vertical TPN DB 4 Way suitable for fixing TPN MCCB 100 Amps main incoming complete all as spoecified and as directed.

Supply and fix MCCB 100 Amps, 4 pole, 50 Hz, 415 Volts with rupturing capacity 25 kA with fixed thermal magnetic setting with separate neutral link including connecting up with suitable aluminium cable lugs etc, complete all as specified and directed.

Supply and fix MCB Single Pole, 240 Volts, 06 to 32 Amps (C Curve) 10 KA rapturing capacity all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm all as specified and directed.

M & L for LT Cable route indicator with a welded/riveted disc of 4inch dia and engraved with cable route marker made out of angle iron 40X40X4mm thick dug in ground and fixing with PCC 1:3:6 type C1 using 20mm graded aggregate at approx distance 100 mtr including necessary earth work complete all as specified and directed

RAJENDRA KRISHNA SARAF

M/s B C CHOUGULE

SOOD ASSOCIATES PVT LTD