DAY TO DAY MAINT OF CERTAIN BLDGS AND REPAIRS TO JOINERY FLOORING SUNKEN PORTION ROOF TREATMENT OF CERTAIN BLDGS AT TECH AREA TAKU ITARSI UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Taking down chowkats or frames with shutter’s (without taking off shutter’s from frame) n exc 1.50 sqm each including making good disturbed area complete all as specified and directed.

Taking down chowkats or frames with shutter’s (without taking off shutter’s from frame) exc 1.50 Sqm & nxc 4.00 Sqm each including making good disturbed area complete all as specified and directed.

Taking down shutters of any description, size of shutter exc 1 sqm but n. exc 2 sqm complete all as specified and directed.

Taking down and refixing same opening shutter exc. 1 sqm and not exc 2 sqm each complete all as specified and directed.

S&F for pressed steel frame for doors with one or more rebates of size 125 x 60 mm including necessary fixing lungs, hinges, lock strike plate etc; including back filling of pressed steel frame with cement concrete 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) complete all as specified and directed.

S&F for pressed steel frame for doors with one or more rebates of size 105 x 60 mm including necessary fixing lungs, hinges, lock strike plate etc; including back filling of pressed steel frame with cement concrete 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) complete all as specified and directed.

Cutting holes in brick walls built in cement mortar for inserting hold fasts, cutting exceeding half brick but not exceeding one brick and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

S&F for solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F for 35 mm thick 2nd class hard wood glazed and skeleton shutter’s for door open rebated prepare to receive glass, gauge, etc; edges of framing plain, chamfered or rounded, fitted with cut and mitered bead’s for securing glass, gauge, etc; size of shutters as per SSR Part-I Section-8 clause 8.2 (a) complete all as specified and directed.

S&F for factory made 30 mm thick flush shutters with solid core construction with plywood face panels, both side covered with decorative face veneer with lipping/ frame to match complete all as specified and directed.

S&F of factory made 35 mm thick 2nd class hard wood, plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers size of members as specified in SSR Part- I Section 8 Clause 8.24 (a) complete all as speified and directed.

S&F of aluminium powder coated of approved colour door with frame and shutters, partially glazing with 5.5 mm thick one side reflective glass (tinted glass) and PVC composite board 5 mm thick fixed with aluminium clip section (including rubber beading), door section of aluminium door shutter shall comprising as under:- (i) Frame 100x45x2mm (ii) Shutter style 85x44.45x2mm (iii) Top rail 95.25x44.45x1.7mm (iv) Middle rail 83.50x44.75x1.7mm thick (v) Bottom rail 114.30x44.15x1.7mm (vi) Glazing clip 0.7mm thick (vii) 2 Nos handle powder coated aluminium 200mm long as approved (viii) Tower bolt 9.90mm dia and 200mm long (ix) Mortice lock 100mm, 7 lever make Godreg or equivalent (x) Hold fast aluminium 100mm long (xi) 1 Nos floor door spring each shutters (xii) Reinforced with 2 Nos 10mm dia MS bar with bolt complete on top and bottom rail of door. (xii) PVC/rubber linning brush for alround door.

S&F of 30 mm thick 2nd class hard wood glazed and Skelton shutters for windows, ventilators, etc; provided with stiles and rails, prepared to receive glass, gauge, etc. divided in squares with size of member as per specified in SSR Part I, Section 8 clause 8.24 (b) complete all as specified and directed.

S&F of box type steel window double frame (glazed & gauged) made of ERW tube P- section of size 60 x 25 mm, double rebated outer frame comprising of glazed skelton shutter door frame of ERW tube P-section size 50 x 20 mm with two Nos openable leaf consisting of two Nos of sash bar of T-sec 20 x 3 mm welded to frame with one No vertcal mullion of ERW box type T-section size of 60 x 25 mm, flat iron 2 mm thick welded / screwed to frame for fixing of wire guage/glass including fixture and fittings like handle, tower bolt, stopper, cleat, pintal hinges, holdfast, etc. complete all as specified and directed. Note: Sheet glass, wire mess, 10 mm square bar security grill will be measered and paid seaperately and window will be measured on one side only.

All as per serial item No. 15 here-in-before but single shutter (glazed) with single frame.

S&F of aluminium powder coated sliding type three track window with shutter and frame including aluminium grill and mosquito proofing net comprising of 4 mm thick tinted glass, size of frame 93.00 x 31.75 x 1.3 mm thick for top and sides, 93.00 x 31.75 x 1.3 mm thick bottom rail and shutter frame 38 x 18 x 1.5 mm thick, aluminium grill 6 mm dia design No DG-102 grill or design No A-103, grill fixed 50 x 20 x 1.5 mm thick rail including necessary handles, tower bolts, stopper etc. complete all as specified and directed.

S&F of aluminium powder coated ventilators having fixed glass/ louvers/ wiremesh with aluminium section having section 50.80 x 25.40 mm (min weight 0.489 Kg/m) glazing clear section with locking clips (min weight 0.109 Kg/m) with and including 4 mm thick frosted glass and making frame and glass water tight etc. complete all as specified and directed.

S&F of aluminium powder coated partitions (Fixed portions) having fixed glass exc each panel 0.50 Sqm with aluminium section having section 65.00 x 27.00 mm (min weight 0.706 Kg/m) glazing clear section with locking clips (min weight 0.109 Kg/m) with and including 4 mm thick frosted glass and making frame and glass water tight etc. complete all as specified and directed.

S&F of 250 mm long stainless steel sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

S&F of 300 mm long stainless steel sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

S&F of 300 mm long mild steel ordinary rat tail, rod pattern springs including roller and roller plate and fixed complete all as specified and directed.

S&F of 150 mm long stainless steel handles, fabricated type and fixed complete all as specified and directed.

S&F of 75 mm long stainless steel butt hinges, primium quality with mild steel hinge pin, bright polished and fixed complete all as specified and directed.

S&F of 150 mm long stainless steel barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F of 200 mm long stainless steel barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F of 140 mm long floor door stopper and tongue of stainless steel body with hard drawn steel spring fixed in floors completeall as specified and directed.

S&F of door closer hydraulically regulated, aluminium (extruded section) body, designation No.2, universal type, suitable for door shutters of weight between 36 to 60 kg complete all as specified and directed.

Resecuring or easing & adjusting without taking down shutters of any description not exc 1.00 sqm each complete all as specified and directed.

Resecuring or easing & adjusting without taking down shutters of any description exc 1.00 sqm and not exc 2.00 sqm each complete all as specified and directed.

S&F of galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinted tacks or wooden beading complete all as specified and directed.

Hacking out old broken glass panes of any thickness description from wooden frame or steel frame, glazed with putty or fixed with beads and prepared to receive new glass panes complete all as specified and directed.

S&F of 3 mm sheet glass ordinary quality and glazing with oil putty in squares n exc 0.50 Sqm each complete all as specified and directed.

S&F of 3 mm frosted glass ordinary quality and glazing with oil putty in squares n exc 0.50 Sqm each complete all as specified and directed.

S&F of 6 mm thick rough cast, wired figured glass and glazing with oil putty in squares n exc 0.50 sqm each pane complete all as specified and directed.

S&F in repairs 300 mm long stainless steel sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

S&F in repairs 150 mm long stainless steel barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F in repairs 150 mm long stainless steel handles, fabricated type and fixed complete all as specified and directed.

S&F in repairs 1.5 mm thick plain colour PVC / acrylic sheeting, fixed with screws and washers in windows/ ventilators etc. complete all as specified and directed.

S&F in repairs 100 mm long stainless steel handles, fabricated oval type and fixed complete all as specified and directed.

S&F in repairs 100 mm long mild steel butt hinges, medium weight cold rolled and fixed complete all as specified and directed.

S&F in repairs 75 mm long mild steel butt hinges, medium weight cold rolled and fixed complete all as specified and directed.

S&F in repairs 140 mm long floor door stopper and tongue of stainless steel body with hard drawn steel spring fixed in floors completeall as specified and directed.

S&F in repairs 300 mm long mild steel ordinary rat tail, rod pattern springs including roller and roller plate and fixed complete all as specified and directed.

S&F in repairs door closer hydraulically regulated, aluminium (extruded section) body, designation No.2, universal type, suitable for door shutters of weight between 36 to 60 kg complete all as specified and directed.

S&F in repairs galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinted tacks or wooden beading complete all as specified and directed.

S&F in repairs 20-25 mm dia chromium plated stainless steel drapary curtain rod of 1 mm wall thickness with SS brackets including fixing with rawl plug and screw in wall including designer dom for curtain rod at ends complete all as specified and directed.

Taking down/ dismantling steel rolling shutter of area n exc 12.00 Sqm complete all as specified and directed.

S&F of steel rolling shutters of 1.25 mm thick laths push pull or manual type without ball bearing including top cover, anchoring rod, hasp and staple and one shop coat of red oxide primer; erected in position complete all as specified and directed.

All as per serial item No 49 here in before but gear operated type with bevel gear box and crank handle.

Taking down the existing rolling shutters from the existing opening and refixing the same in position after carrying out necessary repairs including oiling, greasing, easing out etc. For its smooth functioning complete all as specified and directed.

Demolition of PCC in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square /rectangular) joint free, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors; over and including 15 mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and directed.

M&L for coloured glazed ceramic tiles in walls/ vertical surface of size 450 x 300 & 7 mm thick over and including 10 mm thick rendering in CM 1:4 for backing of tiles, set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 8-10 mm thick (square / rectangular) polished, area of each tile not exceeding 0.36 Sqm as in floors etc; over and including 15 mm thick screed bed in CM 1:6; set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 8-10 mm thick (Square /rectangular) polished, area of each tile not exceeding 0.36 sqm on vertical surfaces such as skirting dado and risers to steps etc; over and including 10 mm thick rendering in CM 1:4; set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in sub base concrete, finished even and rough complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8, type B-1 (using 40mm graded stone aggregate) as in sub base concrete complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C-2 (using 20 mm graded stoen aggregate) as in plinth protection/path, laid in alternate bays and joints shall be filled with bitumastic gola with 80/25 bitumen (1 part bitumen mixed with 3 part of sand) surface finished fair and even complete all as specified and directed.

M&L of 20mm thick screed bed in CM (1:6) as in sub base of floor complete all as specified and directed.

M&L for chequered cement concrete tiles pre-polished lacuqer and rubber/ glossy finish of size 30 cm x 30 cm x 22-25 mm thick, set ,jointed and pointed in neat cement slurry with grey cement and pigment in floors complete all as specified and directed.

Dismantling plain or corrugated AC/ steel sheeting with ridge, gutters, etc, any gauge, and thickness incl nainital pattern roof covering, fibre glass reinforced translucent corrugated sheeting, fixed with J/L hooks or coach screws complete all as specified and directed.

S&F of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheeting 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ-150) as in roof covering / cladding to wall, chajjas, etc. and fixed with self tapping screws complete all as specified and directed.

S&F of pre-painted galvalume aluminum zinc coating GI based plain steel sheeting 0.50mm thick of an colour having tensile strength of 550 Mpa (AZ-150) as in roof covering / cladding to wall, chajjas, etc. and fixed with self tapping screws complete all as specified and directed

S&F of 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side laps, fixed with L or J type or cranked hook bolts/ self tapping screws complete all as specified and directed.

Dismantling framed timber scantlings, exc 40 Sqcm and over in section in any position complete all as specified and directed.

Dismantling the existing ceiling board of any description, position and thickness including cover fillets complete all as specified and directed.

S&F for 6 mm thick plywood, BWP, type BB fixed to timber frame work with nails as in ceiling, flat or sloping complete all as specified and directed.

S&F in position suspended false celling system using E Grid suspended celling grid system of Everest industries Ltd or India Gypsum, sizes of grid shall be 600 x 600 mm with GI frame work, main runner 39 x 24 mm, cross tee 29 x 24 mm and wall angle 22.2 x 22.2 mm with and including 6 mm thick high pressure stream cured non primered classic/ designer variant fibre cement E-Board ISI marked IS No 14862-2000 to be placed in the suspended ceiling grid system duly suspended by 4 mm dia GI bar hangers from the purlins of the roof with butter fly clips complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not other wise provided complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out hard/dense soil and returning, filling and ramming earth or broken rubble mixed with earth with around in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc 50m and making good surface

S&F of mild steel framed work as in roof trusses (framed), trussed, purlins, post, crane gantries, rails, fastenings, ceiling frame and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F of mild steel framed work as in grills, gratings, angle for ventilators etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings and similar work conforming of Fe-290 Gde-E-165 complete all as specified and directed.

S&F of mild steel framed work of rolled mild steel sections as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting, running rails & guides) and hanging, fastening & fixing conforming of Fe-290 Gde-E-165 complete all as specified and directed.

S&F of mild steel plain black sheet 2.00 mm thick in hearths; covering to door shutters; ducts, etc, cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets, fixed to wood or steel members with plain 40 mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, etc as required complete all as specified and directed.

S&F of hard drawn welded steel wire fabric (weight not less than 4 kg per sqm) cut to lengths, bent to shape required and tying to wood or steel members with complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth and applying two coats synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth and applying two coats aluminium paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Taking down/ removing existing roof teatment including earthing strips, backing coat and cleaning of roof slab surfaces including sweeping clean and washing down with water to remove dust with and including M&L for providing water proofing treatment with polymeric standard water proofing membrane complete and comprising of following activities:- (a) Applying 15 mm thick plaster in cement mortar (1:3) using water proofing compound to roof, finished the surface even and smooth without using extra cement. (b) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.20 Kg/sqm. (c) Supply and laying APP based polymeric membrane min wt 3 kg/sqm and min 3 mm thick duly reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) landed on primed surface by forced application including coping with torch application and 10 cm overlaps as required. (d) Applying two coats of aluminium paint @ 0.2 Kg/sqm complete. (e) Carrying ponding test for 72 Hrs for leekage/ seapage. (f) Refixing dismantled earthing point/ strips/ pipe in existing position.

Demolition of reinforced concrete as in roof, floor, etc. (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) with necessary scaffolding and protection as required complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in bed plates, pintle block, columns, posts, boundry pillars, window or door cills, anchorage blocks, etc. with plain fair faces including chamfers, weatherings, throatings, etc. including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. Note: Reinforcement shall be measured and paid seperately.

M&L for formwork to flat rough finished surface of concrete of chullah hoods, chajjas, troughs and similar items including edges at height n exc 10 m complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in chajja repairs at any height including providing and erecting conventional steel double scaffolding to reach at any height/ any place of work on the external façade of the building including complete T&P as required at site inclusive of covering by hessian cloth or tarpaulins and taking away all materials after the completion complete all as specified and directed.

S&F of mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F of mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc. complete all as specified and as directed.

M&L for brickwork with sub class 'B' bricks, straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 complete all as speciified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster of any description on brick walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for 15 mm thick rendering cement plaster on fair faces of brick walls or concrete surfaces in cement mortar 1:4 mixing water proofing compound as per manufacturer instructions, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound will be measured and paid seperately.

M&L for 12 mm thick rendering cement plaster on fair faces of brick walls or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering cement plaster on ceiling surfaces in cement mortar 1:3, finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI marked complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of fire resistant paint over a coat of wall primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of wall primer complete all as specified and directed.

M&L for preparation of newly plastered ceiling surfaces and applying two coats of white washing complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint (weather proof paint on external surfaces) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new plastered wall surfaces at any height of building / tower complete all as specified and directed.

S&F in repairs 15 mm dia bib taps standard of PTMT any colour high pressure screwed for iron pipe and fixed (Min wt - 90gms) complete all as specified and directed.

S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm dia pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed (Min wt - 110gms) complete all as specified and directed.

S&F in repairs 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nut, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm dia angle/stop cock, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm bore stop valve, cast copper alloy, chromium plated, fancy type with capstan heads with long shank and cup (concealed type), screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs of towel ring of PTMT fixed with chromium plated brass screws and wooden/plastic cleats (Min wt - 90 gms) complete all as specified and directed.

S&F of tubular towel rail brass chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

S&F in repairs brass chromium plated shower roses with swivel joints, 125 mm size including fixing to steel pipe or union complete as specified and directed.

S&F in repairs vitreous china urinal, half stall type including all fittings with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in white cement complete all as specified and directed.

S&F in repairs vitreous china squatting pan Orissa pattern size 580 x 440 mm white with integral footrest including trap; set and making conection to trap, flushing pipe etc. including making good to floor complete all as specified and directed.

S&F in repairs vitreous china EWC with 'P' or 'S' Trap , white including Plastic water closet seat cover, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device suitable for EWC. Complete making good to floor fixing bolt all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 Ltr capacity valveless symphonic action type white as approved with ball valve flat back & handle including brackets and flush pipe of PVC 32mm dia complete all as specified and directed.

S&F in repairs plastic water closet seat cover, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repairs chromium plated jet spray/ health faucet (ABS body) suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection and fixed in position complete all as specified and directed.

S&F in repairs 15 mm bore two ways bib cock with wall flange, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs vitreous china wash basins (flat back or angle back type) of size 550 x 400 mm, white incl cutting for & pinning in ends of brackets or erecting stand, brackets, CP brass waste coupling and waste pipe of standard length complete all as specified and directed.

S&F in repairs 32/ 40 mm dia brass chromium plated waste coupling (half and full threaded) complete all as specified and directed.

S&F in repairs PVC connections 15 mm dia and 450 mm long with PTMT nuts and fixed complete all as specified and directed.

S&F in repairs PVC connections 15 mm dia and 600 mm long with PTMT nuts and fixed complete all as specified and directed.

S&F in repairs 32 mm bore polyethylene and unplasticised PVC waste pipe for wash basin, sink and urinal of one metre length complete all as specified and directed.

S&F in repairs 40 mm bore polyethylene and unplasticised PVC waste pipe for wash basin, sink and urinal of one metre length complete all as specified and directed.

S&F in repairs 100 mm dia PTMT/ CP grating with/ without waste hole complete all as specified and directed.

S&F in repairs PVC bathroom mirror cabinet with mirror of size 350 x 450 mm and fixed complete all as specified and directed. Make: Prayag Cat No 551 or equivalent make as approved by GE.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard bar railing 60 cm long complete all as specified and directed.

S&F in repairs stainless steel plate rack (utencil rack for kitchen) of size 750 x 600 x 250 mm of min 0.80 to 1.00 mm thick sheet and fixed with stainless steel screws and rawl plugs complete all as specified and directed.

S&F in repairs kitchen sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and waste coupling and waste pipe; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe of overall size 915 x 460 mm and bowl size 410 x 330 x 160 mm complete all as specified and directed.

S&F in repairs kitchen sink stainless steel waste coupling and PVC waste pipe and fixed complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connections complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections complete all as specified and directed.

Refixing only 15 mm dia steel tubing and connection in new or old position (in walls, ceiling, floors etc) with using new fittings complete all as specified and directed.

Refixing only 15 mm dia steel tubing and connection in new or old position (in walls, ceiling, floors etc) with using new fittings complete all as specified and directed.

S&F of 15 mm dia GI tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F of 20 mm dia GI tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L for cleaning and removing all scale and dirt etc. from tanks and from mouths of circulating pipes etc. of exc. 250 ltrs and n exc. 500 ltrs capcity tanks complete all as specified and directed.

M&L for cleaning and removing all scale and dirt etc. from tanks and from mouths of circulating pipes etc. of exc. 500 ltrs and n exc. 1000 ltrs capcity tanks complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required and reconnecting and refixing in position of cap exc. 250 ltrs but n exc. 500 ltrs complete as specified and directed.

S&F in replacement rotational moulded polythene water storage tank of 500 ltrs capacity (3 layered) hoisted and fixed in position with and including 20 mm size float valves of PTMT with epoxy coated aluminium rod & high density plastic ball (Min wt - 210 gms) and nipple suitable for water tank complete all as specified and directed.

S&F in replacement rotational moulded polythene water storage tank of 1000 ltrs capacity (3 layered) hoisted and fixed in position with and including 20 mm size float valves of PTMT with epoxy coated aluminium rod & high density plastic ball (Min wt - 210 gms) and nipple suitable for water tank complete all as specified and directed.

S&F in repairs HDPE/ plastic water storage tank lid/ cover and fixed complete all as specified and directed.

S&F in repairs 15 mm dia float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe screwed for iron pipe and fixed (Min wt - 142 gms) complete all as specified and directed.

S&F in repairs 15 mm bore tank nipple suitable for HDPE water tanks including necessary driling holes and fixed complete all as specified and directed.

S&F in repairs 20 mm dia float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe screwed for iron pipe and fixed (Min wt - 210 gms) complete all as specified and directed.

S&F in repairs 20 mm bore tank nipple suitable for HDPE water tanks including necessary driling holes and fixed complete all as specified and directed.

S&F in repair 15mm bore ball brass valves, high pressure with polythene float and flynut, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed in walls/ laid in trenches/floors and fixed with solvent cement complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal and fixed with solvent cement complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) bends any radius without access door and fixed with solvent cement complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) bends any radius with access door and fixed with solvent cement complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door and fixed with solvent cement complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed in walls/ laid in trenches/floors and fixed with solvent cement complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) bends any radius without access door and fixed with solvent cement complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) bends any radius with access door and fixed with solvent cement complete all as specified and directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in repairs 75mm dia PVC (SWR) floor/nahani trap with grating including jointing with solvent cement complete all as specified and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 63600.00

M/S HARSH VIKAS GALAR ENGINEERING (BID ID -3450867)

TANUJ CONST. CO. (BID ID -3449202)

Dashmesh Enterprises (BID ID -3445008)