Const. of various works against saving of RASSOCA building at Bhilwara

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix.

Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc.

Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786), Thermo-mechanically Treated bars (Conforming of relevent IS code).

Stone slab roofing on ground floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4, with ceiling pointing in cement sand mortar 1 : 3 complete as per specification and instruction of Engineer In Charge

Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering.M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

TUBE WELL

SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

150 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively.

5.0 HP, 3-Ø, (68 - 102)Mtr, (225-85) LPM

Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

12mm (suitable up to 50 mm OD pipe)

For Three phase Submersible / Mono block pump

3.0 HP to 5.0 HP ( DOL starter )

P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

2.5 Sq.mm 3 core flat / Round

Providing & Fixing of HDPE pipe Confirming to IS:4984:2021 for water supply suitable for submersible & jet pump with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

for vertical installation

40 mm OD 6 kg / cm2

Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe: 200 mm dia nominal bore

S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size:

a) 200 mm dia

S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set.

P & F G.I. Pipes (External Work) with G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc.

a) 25 mm dia nominal bore B Class

a) 50 mm dia nominal bore B Class

Making connection of G.I. distribution branch with G.I. Main including all fitting.

b) beyong 25 mm upto 100 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work).

25mm nominal size

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :

b) Gun-metal 25 mm nominal bore

c) Gun-metal 50 mm nominal bore

P&F gun metal non return valve or check valve (IS Make) of approved make, superior quality

50 mm nominal bore

a) Horizontal

Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size :

b) 25 mm dia nominal bore

c) 50 mm dia nominal bore

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:

(-do-) Long body, 15mm nominal bore weight not less than 690 gm

Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work.200 mm Nominal bore of pipe

Electrical work

Supply , Installation, Testing and Comissioning of Inverter type Air Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410 Green Refrigerant, wireless Remote control, suitable for working between 230V +/- 10% with low & high voltage cutoff and 50 hz , single phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

2.0 TR ISEER not less then 3.8

Supply, Fixing and testing of following capacity ISO certified company made wall mounted stabilizer having output voltage variation from 200 V to 250 V(+/-5%) with input voltage variation from 170 V to 260 V, time delay facility from 2 to 4 minute and high cutoff at 270 V with providing of 16 Amp /20 Amp Industrial plug top making connection etc complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Providing & Fixing of IS : 4985 - 2000 Class -4 (10 Kgf / Sqcm) UPVC drain water piping with fittings (IS:7834 & 10Kgf/sqcm) like elbow, socket, Tee, solvent cement jointing, support with MS hanger on ceiling or recessed in wall with chasing & plastering with 6 mm thick closed cell elastomeric nitrile rubber insulation including leakage testing etc. as required of following Nominal sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Supply, installation, testing and comissioning of interconnecting copper refrigerant piping of DHE Grade C12200- ASTM B68, B75, chemical composition of copper %- 99.0 Min and Phosphorus %- 0.015 to 0.040 . For Annealed copper tube :- Tensile strength = 210 Mpa wih elongation % = 40 Min . Ink Mark Brand Printing on Hard Tubes should be present. duly insulated with tubular elastomeric nitrile rubber FM/UL approved with high water vapor diffusion resistance and low thermal conductivity should be certified 'Class O' in Fire Propagation as per BS 476 Part 6 including chase cutting andfilling with mortar, Slotted channel supports mounted on 10 mm threaded rod at suitable spacing the exposed piping shall be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tape of 3 mm thick complete as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

25 mm O.D., wall thinkness ≥ 1.2mm (insulation – 19 mm thick)

Supply, Installation, Testing & Commissioning of 2 KVA 1 Phase Input,with GBT Based Rectifier True Online Double Conversion Robust design Wide input voltage range: 160~300VAC@ 100% load{linearly derating to 50% load@ 100VAC input). Generator Compatible with Wide Input voltage window Double Conversion Efficiency >91% & ECO mode efficiency up to 98% 100% load @0-40C operating temp. Active Input Power Factor Correction 0.99 O/P power factor 0.9 Inbuilt OVCD (Over Voltage Cut-off device) Fully conform coated PCBA adaptable to harsh environment Offer terminal blocker on 2K/3K rating to big capacity equipment Digital Charger Technology provide 02-10 A charging ct.irrent Easy understanding LCD for convenient installation setup with Minimum 60 minute battery back up (26AH x 6 Nos of SMF batteries branded and recommended by UPS OEM, battery stand and interlink FR PVC copper cable of appropriate size and lugs), with required cabling for incoming & outgoing connection. UPS should be NABL certified with CE, ROHS & BIS compliance. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR /

Item Rate BoQ

BoQ_Ver3.0

NIB No: 12/2025-26. NON BSR ITEM

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Supply and Installation of Office table as per approved design and as directred by Engineer-in-charge Work Top-Work top shall be made 25mm thick Pre-lam MDF board confirming to IS 12406:2003 with post foming on front and back and machine pressed PVC egde banding 2 mm thick glued with industrial adhesive and diffused with board monolithically on other two sides Understructure- C-type leg shall be made of 50X50X1.6mm thick vertical member and 40x40x1.6mm thick M.S. pipe of Horizontal/Cross member confirming 15-Grade 4923 shall be finised shall be finised with epoxy polyster powder coated DFT 50-60 Mieron. Legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 12mm to 15mm.Cross members shall be mounted by end brackets made of 3mm thick 15 513: 2008 CRCA sheet shall be finised with epoxy polyster powder coated DFT 50-60 Micron confirming IS 13871:1993. Wire management-Electrical wires shall be carried from horizontal/ vertical duct made of 0.7mm CRCA sheet confirming to 15 513:2008. Switch Plate or Cromet depending upon requirement shall also be provided for electrical/LAN connection on table top. Modesty Panel-Modesty Panel of height 450 mm shall be made of 1.2 mm thick CRCA sheet confirming to I5 513: 2008 and shall be finised with epoxy polyster powder coated DFT 50-60 Micron. Side Storage body-Storage top shall also be made of 25mm thick Pre-lam MDF board confirming to IS 12406:2003 with post forming on two sides and machine pressed PVC egde banding 2 mm thick glued with industrial adhesive and diffused with board monolithically on other two sides. The body of storage units shall be made of 0.8mm thick CRCA Sheet and skirting shall be of 1.2mm thick CRCA sheet confirming to 15 513: 2008 finished with epoxy powder coated of DFT 50-60 Micronconfirming IS 13671:1993. Internal Shelves shall be also made up of 0.8mm CRCA sheet confirming to 15 513: 2008 and shall be mounted with the Metal shelf support pin made of 2mm thick CRCA sheet with Nickel or Chrome plating. M10 screw leveler is given with height adjustment up to 12mm to 15mm. Back storage should be in complete18 Prelam particle board matching with similar colour shade : structure made in 18 mm plpb The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for EDUCATIONAL FURNITURE range for ergonomic design.

Main table size 1800 x 750 x 750, Side storage 900 x 450 x 750, Back storage 1800 x 450 x 750,

Main table size 1350 x 750 x 750, Side storage 900 x 450 x 750

Supply and Istallation of Computer Work Station of unit Size 750 mm X 600 mm X 750 mm. Work Top- Work top shall be made 25mm thick Prelam particle board confirming to IS 12823: 1990 with post formed edge moulding on one side and 2 mm thick Machine pressed PVC edge banding glued with industrial adhesive and monolithically diffused with board on other three sides. Understructure supporting frame consist of Metal C Legs type made up of 50 x 50 x 1.6 mm and Wire Carrier leg of 50X50X1.6 mm in placed alternatvely and are connected with horizontal cross connectors of of 40mm x 40mm X 1.6mm thick MS Pipe between supporting vertical legs. The MS Pipes shall be finished with epoxy powdercoated with DFT of 50-60 Micron confirming to IS 13871:1993. Legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 12mm to 15mm. Wire management-The Vertical/Electrical duct & Horizontal Cable tray (wire carriers) are made of CRCA & fixed to the understructure below worktop with specially designed brackets. Provision for fixing Switch plates are privided in the cable tray for easy access through wire mangaer or PVC grommet. Screens/privacy panel:- Screen height will be 300 above work-top made of prelam particle board/White Board alternatively as approved by Engineer-in-Charge.

Supply and Istalltion of Library Open book Shelf (Single Side )of Sizes 1800 mm x 900 mm x 316 mm body made up of of 0.8mm thick CRCA Sheet and skirting of 1.2mm thick CRCA sheet confirming to IS 513: 2008 with epoxy powder coated finish (DFT minimum 50-60 micron). Shelves shall also be made up of 0.8mm CRCA sheet confirming to IS S13: 2008 and fixed with CRCA sheet brackets of approved design. Number of adjustable shelf shall be five with six loading levels. Load bearing capacity of the shelf shall be 30Kgs UDL. The construction shall be aesthetically appealing completely welded. M10 screw leveler is given with height adjustment up to 12mm to 15mm

Overall Size 915W x 485D x 1980H . Office Almirah Made Of Prime Quality CRCA Ms Sheet Panels 0.8mm Thick Powder Coated Finish With Approved Shade . Each Shelve Made Of 0.8mm CRCA MS Sheet Powder Coated . Each Shelve Shall Be Formed Such The Edges Are Bend Two Times At Right Angle. Front Shutter 1mm Thick CRCA Ms Sheet Powder Coated Riveted With Hinges. . No Sharp Edges Of Almirah Ends . Glass Thickness Shall Be 3.5mm . Glass Shall Be Fitted In Additional Shutter Frame From Inside . Leg Shall Be 125 x 90 X 452MM 2 Nos . Door Die cast Chrome Plated Handles Fitted With Washer & Double Nut . Handles Ring Made Of PVC Cap . Locking Bright Bar 10mm Dia . Almirah All Metallic Panels Screw With Nut & Bolt . Bottom Shelve 125mm High Up To Ground. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STORAG FURNITURE range for ergonomic design.

HB H : 1140 ±10 X W : 715 ±10 X D : 715 ±10 . High Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed . Upholstery PVC Structure Moulded With Prime Quality High Stretch Knitted Polyester Fabric . PHA ( Gas-Lift ) 85mm (TDC 152mm & BDC 67) . Seat & Back Are Firmly Connected To The Base Frame Machanism Moves In The Ratio 1:2 . Machanism Provided Upright Position Locking . Chair Max Height 1140 & min Height 1055 . 470W x 480D Base Seat 60mm Thick Moulded With PU Foam & 510W x 640H Back Seat 60mm Thick Moulded With HD Foam. 220x500/640 Arm Rest Fitted To The Seat With Armrest Connecting Brackets. Tilt Adjustment Can Be Operated In Seating Position . Armrest Should Be Injection Moulded From Black Nylon . Height From Seat To Ground 450mm. Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 665mm Without Casters. Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . Pedestral Pitch Centre Dia 665mm Without Casters . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

MB H : 1010 ±10 X W : 715 ±10 X D : 715 ±10. Medium Back Chair Made Of Good Quality Products MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed . Upholstery PVC Structure Moulded With Prime Quality High Stretch Knitted Polyester Fabric . PHA ( Gas-Lift ) 85mm (TDC 152mm & BDC 67) . Seat & Back Are Firmly Connected To The Base Frame Machanism Moves In The Ratio 1:2. Machanism Provided Upright Position Locking . Chair Max Height 1010 & min Height 925 . 470W x 480D Base Seat 60mm Thick Moulded With PU Foam & 510W x 510H Back Seat 60mm Thick Moulded With HD Foam . Tilt Adjustment Can Be Operated In Seating Position . 220x500/640 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Armrest Should Be Injection Moulded From Black Nylon . Height From Seat To Ground 450mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 665mm Without Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . Pedestral Pitch Centre Dia 665mm Without Casters . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Visitor Chair Made Of Good Quality Products MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed . Upholstery PVC Structure Moulded With Prime Quality High Stretch Knitted Polyester Fabric . Seat & Back Are Firmly Connected To The Base . Chair Max Height . Base Seat 60mm Thick Moulded With PU Foam &Back Seat 60mm Thick Moulded With HD Foam . Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Armrest Should Be Injection Moulded From Black Nylon . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Please Enable Macros to View BoQ information