Providing Fire Fighting work in Judicial Complex at Hansi in Hisar District. (Without GST)

Amount

[10.58]Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

[10.63.2]Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 2. Size of Tile 600x600 mm

[22.103.3]Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 3. 25 mm nominal bore

[22.181]Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

[4.14.1]Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. All kinds of soil.

[6.1.6]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

[6.14.1]Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

[6.34.6]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level. 6. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing dial type pressure gauge with isolation cock and pipe at hydrant station. ( ALREADY APPROVED VIDE T/O MEMO NO . 40033/WI DATED 10.03.2022 IN THE CASE OF SDO CIVIL COMPLEX AMBALA CANTT. ( NS ITEM ) Dial diameter 100mm calibration 0-15 kg.

Providing and fixing standard short size stainless steel branch pipe with gunmetal nozzle 16 mm dia outlet with standard instantaneous type 63 mm dia coupling. ( DSR CODE NO.18.1 )

Providing and fixing black steel pipes including all fittings like anchor fastners, couplings, bends, elbows, tees etc. welding as required, including anticorrosive treatment to buried pipes by wrapping with 4 mm thick bitumastic membrane applied over a coat of primer, cutting holes and chases in brick or RCC walls with excavation and back feeling making good complete for use in external works. (External)

Providing, fixing, jointing, testing and commissioning M.S. pipe to I.S. 1239 (heavy class) with fittings like, unions, couplings, bends, elbows, tees, offsets, reducers, flanges as per table `E` etc. Painted MS structural supports, hangers, fasteners etc. as directed complete the work as per the requirement at site including painting with two coats of synthetic enamel paint, over two coat of primer after surface preparation, cutting and making good the walls complete. Pipe upto 40 mm dia will be with Socket welded joints with malleable iron fitting conforming to IS: 1879 and 50 mm dia and above will be with butt welded joint (pipe upto 50mm dia shall be chilly clamp supported and above 50mm dia shall be MS structural supported) 100 mm dia

Providing, fixing, testing and commissioning ISI marked S.S fire hydrant valve 80 mm inlet with single outlet and fitted with 63 mm dia instantaneous female coupling on the outlet complete including companion flange as per table `E`, PVC blank cap and chain, nuts, bolts and 3 mm thick compressed asbestos gasket at locations as per drawings (Hydro testing pressure of 21Kg/Sq.cm) (conforming to I.S.5290-1993 Type A.) (DSR Code No. 9.1)

Providing, fixing, testing and commissioning first aid fire hose reel drum, wall mounting, swinging type fitted with 20 mm dia 36.5 m long thermo plastic hose to I.S. 12585 with 5 mm SS nozzle with shut off valve (I.S. 884-1969). Name of Manufacturer should be embossed on the drum. ( DSR CODE NO.17.1 )

Providing and fixing 63 mm dia 15 m long rubberized fabric lined hose including stainless steel male and male instantaneous type coupling approved by fire authority, machine wound with G.I. wire complete in all respects. Hose shall conform to I.S. 636 Type II and coupling to I.S. 903-1975 with ISI certification. (Two per hydrant station) ( DSR CODE NO.16.1 )

Providing and fixing standard fireman`s axe(Conforming to IS: 926) with heavy insulated rubber handle tested for 20000 watts.

Providing and fixing Weather proof hose cabinets fabricated from 16 g M.S. Sheet with full glass door and locking arrangement, suitable to accommodate 2 Nos. single headed Hydrant landing valve, 2 nos. 15 M long hose and 1 No branch pipe/ fire brigade connectors, 2 Nos. fire extinguishers. The cabinet shall be painted with one coat of primer and finished stove enamelled `Fire Red`, `Fire Hose` written on front including suitably mounted on a raised masonry platform as required.(Approx 0.75m x 0.6 m x 0.3 m). ( NS ITEM )

Providing, fixing, testing and commissioning cast iron butterfly valves of PN 1.6 rating with SS-316 grade disc complete suitable for pad locking arrangement including supply and fixing of pad lock with universal key with bolts, nuts, 3 mm thick compressed asbestos gasket, companion flanges as per table `E` complete in all respects. c) 100 mm dia ( DSR CODE NO.11.5 )

Providing, fixing, testing and commissioning cast iron butterfly valves of PN 1.6 rating with SS-316 grade disc complete suitable for pad locking arrangement including supply and fixing of pad lock with universal key with bolts, nuts, 3 mm thick compressed asbestos gasket, companion flanges as per table `E` complete in all respects. c) 150 mm dia ( DSR CODE NO.11.6 )

Providing, fixing, testing and commissioning C.I. dual plate wafer type non return valves of PN 1.6 with SS-316 grade disc including washer, nuts, bolts, 1.5 mm thick compressed asbestos gasket companion flanges as per table `E` complete in all respect, including painting , chain, padlock, lable, tamperproof security tag with serial no. marking, complete a) 150 mm diameter (NS Item)

SITC of Electric Motor Driven Hydrant and Sprinkler Pumps (Location : Plant Room) : Pumps will be Factory assembled comprising of following: SITC of Electrical motor driven fire pump suitable for automatic/ manual operation consisting of the following :- i) Horizontal end suction single/ double stage centrifugal fire pump capable of delivering 900 LPM against a total head of 35 m, 2900 RPM with multi spring mechanical seal, Phosphorous bronz impeller, wearing ring complete with connection to suction and delivery line, and includeing bypass aggangement for testing of pumps. Pump shall have a name plate indicating, head discharge, stages, RPM and direction of rotation. Pump shall be capable of handling not less than 150% of rated capacity at a head not less than 65 % of rated head. The shut off head shall not exceed 120% of rated head. HP of motor should be 20% more than the calculated HP. ii) Squirrel cage, induction motor, TEFC type suitable for 415 plus 6%V, 3 phase, 50 Hz, AC supply, of suitable HP rating for the above pump with synchronous speed of 1450 RPM conforming to IP 55 protection and class `F` insulation. The motor shall conform to IS 325 1978(up to date) with flexible coupling and coupling guard . iii) Epoxy coated common base plate for mounting pump and motor fabricated of mild steel channel as per manufacturer`s recommendation with required no. of heavy duty Anti Vibration pads. v) Flexible Coupling and coupling guard for direct coupling of pump and motor. vi) Drain Pipe (25 mm dia) q Technical Parameter Main Hydrant and Sprinkler Pumps. · Flow rate/Discharge : 900 LPM a) Head - 35 m · Motor HP - 10 HP (Approx.) or as per manufacturer recommendation · Material of construction a) Casing - CI b) Impeller - Phosphorous Bronze c) Shaft - SS 304 · RPM - 2900 RPM Seal: Mechanical seal vii) Rate should be inclusive of foundation bolts, viberation elimination peds (DSR Code No. 4298)

Electrical Motor Driven Jockey Pump, Location - Plant Room :` Pumps will be Factory assembled comprising of following: SITC of electrical motor driven Jockey pump suitable for automatic/manual operation consisting of the following: i) Horizontal multistage jockey pump with cast iron body, Bronze impeller, stainless shaft with mechanical seal capable of delivering 180 LPM against total head of 70 M at 2900 RPM complete. The system shall be complete with pressure gauge with gun metal shut off cock on delivery side. The pump should meet the recommended requirement and must be approved by the local fire authority. ii) Squirrel cage induction motor suitable for 415 plus 6%V, 3 phase, 50 Hz, AC supply of suitable HP rating for the above pump with synchronous speed of 2900 RPM T.E.F.C type connected to pump with flexible coupling and coupling guard . iii) Common base plate for mounting pump and motor fabricated of mild steel channel as per manufacturer`s recommendation with heavy duty required Nos. Anti Vibration pads. iv) Suitable reinforced cement concrete pump foundations as per manufacturer`s design including foundation bolts, nuts and washers as required. v) Drain pipe vi) Rate shall include inter connecting foundation bolts etc. complete. q Technical Parameter of Jockey Pump : a) Jockey Pump :- · Flow rate/Discharge : 180 LPM · Pumping head: outlet-70 M head Seal: mechanical seal · Motor HP : 12 HP (Approx.) or As per manufacturer recommendation (DSR CODE NO.4310)

Providing and fixing MS pipe Class ‘C’ diesel engine exhaust pipe (including all fittings, clamps, steel support 50mm thick glass wool isulation with 24 guage aluminium cladding, bird proof cowl, etc.) of suitable dia for the engine. The pipe shall be provided with 12 mm thick supercera ceramic fibre rope. 80mm dia Exhaust Pipe ( NS ITEM )

Air Vessel for Fire Pump: Providing, fixing, testing and commissioning of air vessel (size 250mm dia and 2100mm height) fabricated from 8mm thick shell and dished end 10 mm thick M.S. Plate for hydrant/ Sprinkler system complete with 25mm dia sockets for pressure switches and pressure gauges including supply and installation of 50mm dia drain valve, pressure relief valve with isolation ball cock, 65mm dia inlet, duly painted from inside the epoxy paint and outside with enamal paint complete as required along with 450mm high supporting legs (for Main Pumps).,Note: Contractor should submit general arrangement drawings before fabrication of vessel and ultrosonic test report to be submitted on supply of vessel. (NS Item)

Supplying, installation, setting, testing and commissioning of differential type pressure switches of size 100 mm dia for pressure range upto 10Kg/cm2 for operation of filter feed pumps. ( NS ITEMS )

Providing and fixing resilient rubber lined neoprene single arch vibration eliminators with unit control suitable for fire pump upto 45 deg C. Temperature working pressure 20 Kg. per square centimeter . 80mm dia (NS Item)

Providing and fixing resilient rubber lined neoprene single arch vibration eliminators with unit control suitable for fire pump upto 45 deg C. Temperature working pressure 20 Kg. per square centimeter . 150mm dia (NS Item)

Providing and fixing 25 mm dia pressure relief valve 15Kg/cm sq. (NS ITEM )

Supplying, Installation, Testing and Commissioning of cast iron wafer type dual plate Non return valves with SS-316 grade disc of following sizes conforming to relevent IS specifications and tested for a minimum pressure of 16 Kg/cm² for sheet and 24 Kg/cm² for shell including companion flanges providing and fixing nuts, bolts, washers, gaskets etc. complete as required. 80mm dia (DSR Code No. 11.4 a)

Supplying, Installation, Testing and Commissioning of cast iron wafer type dual plate Non return valves with SS-316 grade disc of following sizes conforming to relevent IS specifications and tested for a minimum pressure of 16 Kg/cm² for sheet and 24 Kg/cm² for shell including companion flanges providing and fixing nuts, bolts, washers, gaskets etc. complete as required. 150mm dia (DSR Code No. 11.6)

Providing and fixing SS collecting Four Way head with 63 mm dia instantaneous type inlet and 150 mm dia flanged outlet with built in check valve and drain valve for fire brigade connection to under ground tanks ( IS. 904 -1983 ) complete in all respects with companion flanges, nuts, bolts, gaskets,etc. (DSR CODE NO.19.2 )

Providing and fixing SS collecting 3 Way head with 63 mm dia instantaneous type inlet and 100 mm dia flanged outlet with built in check valve and drain valve for fire brigade connection to under ground tanks ( IS. 904 -1983 ) complete in all respects with companion flanges, nuts, bolts, gaskets,etc. (NS ITEMS)

Providing and fixing SS fire brigade suction head (draw off connection) with 63 mm dia instantaneous type male draw out with PVC blank cap, 100mm dia CI foot valve at bottom of pipe inside the tank, nuts, bolts, washers complete in all respects for fire tank ( 100mm dia MS Pipe will be paid seperately). (DSR CODE NO.19.1)

Supply and fixing of 4 nos. G.I. round bottom fire buckets of 9 liters capacity filled with sand including proper supporting / mounting arrangements in MS angle iron frame, painted by fire red colour over two coats of red oxide paint and written with white paint `FIRE` complete in all respects as per the directions of Engineer-in-charge. (NS ITEMS )

Supply and Laying of 1000 mm wide and 5 mm thick insulated mat dame from highly electrical resistant elastomer of tested quality to withstand 30 KV dielectric strength as per IS:15652 complete in all respect (For Fire Pumps Control Panel) ( NS ITEM )

Supply, Installation, Testing and Commissioning of following XLPE insulated and PVC sheethed XLPE Power Cable of 1.1 kV grade Al /Cu Coductor Armoured cable of following sizes in existing Cable Tray or Surface mounted with suitable clamps, saddles, fixing bolts including connecting testing and commissioning and complete the work as per drawing and specifications. 3.5 core x 95 sq mm Al Conductor Cable ( DSR EandM CODE NO.9.1.13 )

Supply, Installation, Testing and Commissioning of following XLPE insulated and PVC sheethed XLPE Power Cable of 1.1 kV grade Al /Cu Coductor Armoured cable of following sizes in existing Cable Tray or Surface mounted with suitable clamps, saddles, fixing bolts including connecting testing and commissioning and complete the work as per drawing and specifications.3 core x 25 sq mm Al Conductor Cable ( NS ITEM )

Supplying and making End termination with brass double compression glands and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 kV grade as required. 3.5 core x 95 sq mm Al Conductor Cable (Single compressor) ( DSR EandM CODE NO.9.1.13 )

Supplying and making End termination with brass double compression glands and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 kV grade as required. 3 core x 25 sq mm Al Conductor Cable (Single Compressor) ( NS ITEM )

Providing and fixing armoured Power / control cables 1.1 KVA grade including necessary support clamps at walls /ceiling level and connection complete in all respects. (Pressure Switch to Starter Panel) 2 core 1.5 Sq.mm Copper Conductor ( Power Cable) ( DSR 2018 CODE 17.5.2)

Providing and fixing armoured Power / control cables 1.1 KVA grade including necessary support clamps at walls /ceiling level and connection complete in all respects. (Pressure Switch to Starter Panel) 4 core 1.5 Sq.mm Copper Conductor ( Power Cable) ( NS ITEM )

Providing and fixing armoured Power / control cables 1.1 KVA grade including necessary support clamps at walls /ceiling level and connection complete in all respects. (Pressure Switch to Starter Panel) 6 core 1.5 Sq.mm Copper Conductor ( Power Cable) ( Ns ITEM )

Supply and fixing of pregalvanized factory fabricated Enamel Painted (2 coat primer and 2 coat enamel paint of seamens gray shade) Perforated type cable trays as per specification including neccessary bends, tee, reducers, couplers, GI nut bolts including cutting, bending, drilling, bolting etc along with all accessories required for suspension from ceiling/Wall complete as required , supports and fixing hardware like anchor fasteners, hangers, earth strip etc.: 150 mm x 50 mm x 1.6 mm ( NS ITEM )

Supply and fixing of pregalvanized factory fabricated Enamel Painted (2 coat primer and 2 coat enamel paint of seamens gray shade) Perforated type cable trays as per specification including neccessary bends, tee, reducers, couplers, GI nut bolts including cutting, bending, drilling, bolting etc along with all accessories required for suspension from ceiling/Wall complete as required , supports and fixing hardware like anchor fasteners, hangers, earth strip etc.: 300 mm x 50 mm x 1.6 mm ( NS ITEM )

Supply, Installation, Testing and Commissioning of the following size of GI strip/wire clamped to wall, cable trays complete as required including interconnection between lengths at joints, all fixing accessories saddles, clamps etc. and other fixing hardware.32 x 6 mm Strip ( NS ITEM )

Supply, Installation, Testing and Commissioning of the following size of GI strip/wire clamped to wall, cable trays complete as required including interconnection between lengths at joints, all fixing accessories saddles, clamps etc. and other fixing hardware.25 x 6 mm Strip ( NS ITEM )

Supply, Installation, Testing and Commissioning of the following size of GI strip/wire clamped to wall, cable trays complete as required including interconnection between lengths at joints, all fixing accessories saddles, clamps etc. and other fixing hardware. 8 SWG GI Wire ( NS ITEM )

SITC of 46 mm steel fire check door of 120 minute fire rating confirming to BS 476 part -22 and 3614 part 11 fabricated with two no., 1mm thick galvanized steel sheet sandviching with proprietary fire resistant insulation material between .The door frames are manufactured from 1.5 mm thick galvanized steel sheet pressed to double ribbed profile to size 143mm*57mm , the door frame to door shutter to finish with powder coating Location Basement staircase, electric control room and all floor stair case where there is no natural ventilation (NS Item)

Supplying, installation, testing and commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. ( DSR 2018 code 17.1.2 )

Supplying, installation, testing and commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain and hammer assembly complete with glass and push button etc. as required. ( DSR 2018 code 17.1.3 )

Supplying, installation, testing and commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate and suitable for operation with amplifier i/c line matching transformer etc. complete as required. ( DSR 2018 code 17.1.6 )

Supplying, installation, testing and commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.10 zone ( DSR 2018 code 17.1.9.3 )

Supplying and laying of 2x1.5 sqm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring and FRLS outer sheath complete as required. ( DSR 2018 code 17.5.2 )

speaker cable Single pair, 2-core, 1.5 sqmm Metre ( DSR 2018 code 17.5.3.1 )

Providing and fixing Carbon-di-oxide type fire extinguishers consisting of welded M.S. cylindrical body, internal discharge tube, discharge nozzle, suspension bracket, conforming to IS 15683, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. a) Capacity 4.5 kg ( NS ITEM )

Providing and fixing stored pressure vessel ABC Powder type fire extingushers consisting of seamless cylindrical body, squeeze lever dischange valve fitted with pressure indicating guage internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS : 15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. a) Capacity 6 Kg. (NS Item)

Providing and fixing stored pressure vessel Mechanical foam type extinguishers (a) Capacity 50 ltrs ( NS )

SITC of following fire fighting panel suitable for 415 V, plus /- 6% Volts, 3 phase, 4 wires, 50 Hz power distribution system. The panel shall be free standing floor mounting sheet metal enclosed dust and vermin proof conforming to IP-52, compartmentalized design, fabricated out of 14 SWG sheet steel. painting, earthing numbering, danger plate as per specifications and drawings flush front with Aluminium busbars, separate earth bus bars to be provided throughout the length of the panel. The Incoming and outgoing feeder breakers, fuses, indicating lamps etc shall be accommodated in a modular multitier arrangement. The painting shall done as per relevant IS codes/as specified in the specifications. Adequate size cable alley shall be provided all round the panel and in the back for each cable bending and termination. The panel shall be fabricated by TAC/Fire authority approved vendor. The outgoing feeders inside the panel shall be connected through solid bus bars, Flexible cable links are not acceptable. (NS ITEM)

Damia Global Services Pvt Ltd

SAI FIRE APPLIANCES PVT LTD