Spl repair to Bldg No P-1 (JCOs Accn) at UHQ of Network Sig Regt and provn of certain sanctioned works at Mil Stn Jammu under GE Satwari

Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removing unserviceable material from work site to outside defence premises complete all as specified and directed

M&L for brick work with sub class 'B' bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed

M&L for pressed steel cup board frame made out of MS sheet 1.25mm thick, size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 type B-1 as in filling to back of chowkats complete all as specified & directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

All as per Srl item No -25 here-in-before but except bricks complete all as specified and directed

M&L for glazed ceramic coloured digital tiles,300x600x7 to 8 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C2 (using 40mm graded crushed stone aggregates) as in sub base of floors/hardstanding, finished even and fair complete all as specified and as directed.

S&F UPVC (SWR),branch single, (single 'Y') with access door equal or unequal for 75 mm bore complete all as specified and directed

Supply only liquid water proofing compound.

S&F machine cut kota stone slab in flooring, treads of steps (one piece including rounding/ mouldings of edges of treads), 20-25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fair including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:2 complete all as specified and directed .

Dismantling wall and ceiling boards (fibre,pulp, insulation) or insulation boards/ slabs/ blankets, any thickness, including cover fillets etc complete all as specified & directed.

S&F UPVC (SWR), junction single, (single 'T') equal or unequal for 75 mm bore complete all as specified and directed

M&L for rendering 15mm thick in cement mortar 1:4 on concrete surfaces of roof finished even and fair including mixing of water proofing compound as per manufacturer's instructions complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately as supply only.

S&F corner glass shelf of size 30cm with chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed .

S&F aluminium anodised , fabricated type handle 100mm size complete all as spcified and directed.

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for preparation of new or previously untreated wood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

d 10 micron metalized polyester film on the back side fixed on GI snap grid complete all as specified and directed ..

S&F UPVC (SWR),branch single, (single 'Y') with access door equal or unequal for 110 mm bore complete all as specified and directed

M&L for complete removal of existing treatment on wall/ceilling,roof projectios,Including facia,cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. by skilled labour complete all as specified and directed .

M&L for water proof cement based putty @ 1kg (undiluted) per sqm of average thickness 1 mm over the plastered painted exterior wall surfaces of walls (upto 4th storey with necessary scaffolding ) including prepartion of surfaces by scarpping to prepare the surface and sanding of the putty surfaces with mechanical wall sander (having mechanical vaccum mechanism ) having RPM not less than 1500 ,sanding pads of 240 Grit or above to make the surface free from dust etc by skilled llabour as per following steps:- Steps 1:- Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of minimum 2.5 kg putty per minute. Step 2:- Apply the first coat of prepared mixer with the manually required help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation. Step 3:- Allow 6 to 8 hour time to dry the putty surface, Apply the further more coat of preparaed mixer with the help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation.

M&L for one coat of acrylic water based exterior grade primer @ 0.9 ltrs (undiluted) per 10 sqm, diluted with water in 1.1 ratio to be applied with fully automatic airless spary machine o

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described to make surface even and smooth & apply primer where required and applying one coats of synthetic enamel paint complete all as specified and directed.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 8mm dia pipe with 1.20 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making good the disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Taking down of unserviceable MCB DB, SPN /TPN along with MCB's complete all as specified and directed

Taking down of unserviceable sub main wiring of any size complete all as specified and directed

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid medium grade concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, stranded connected to common earth point dolly for one light point/fan point/call bell point, 230 volts controlled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications.

S&F PVC connection 15 mm x 600 mm including PVC check nut at both ends complete all as specified and direced.

Complete removal of existing water proofing treatment of any description including under layer, taking down cement plaster & concrete, any thickness and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust and removal of debris off the premises including grubbing up of trees complete all as specified and directed.

S&F modular type switch, one way 6 Amps , 1 module complete all as specifieds and directed .

S&F modular type socket 3 pin, 6 Amps, 2 module complete all as specifieds and directed .

S&F modular type switch, one way, 16 Amps, 1 module complete all as specifieds and directed .

S&F modular type socket 3 pin, 6 A/16 Amps, 2 module complete all as specifieds and directed .

M&L for water based premium acrylic smooth interior emulsion of approved colour with silicon additive excellent dirt pick up resistance with low VOC less than 50 Antifugal, Anti Algai properities in two coats @ 1.79 lites (undiluted) per 10 Sqm diluted with water as per manufacturer instructions applied over priming surface in between subsequent coats of paint (upto 4th storey with necessary scaffolding) complete all as specified and directed . Notes for Srl item No 104 to 108 of BOQ :- (a) The work for periodical services shall include the under mentioned aspects and the rates quoted by the bidder shall includes and the same & nothing extra shall be payable. (i) Work shall be carried out by the authorised applicator of manufacturer of water based premium acrylic smooth exterior emulsion, contractor shall submit a triparty agreement MoU (between contractor ,said manufacturer and their authorities appicator ) on Non judicial stamp paper to GE and shall be approved by the GE before commecement of work at site. (ii) Work shall be carried out up to 4th storey height buildings and the necessary scaffolding , trestles , ladders ,cradles & safety measures shall be arraged by the contractor for labour and their own . (iii) Removing of nails & making good holes, cracks etc. (iv) Work in patches and in narrow /widths ,bands ,cornises ,plasters etc shall also be carried out and cutting in edge of line where ncessary. (v) Spreading and removing covering to doors ,windows ,floor ,fittings etc to protect them from splashes. (vi) Washing floors , cleaning glass ,joinery, fittings, wiring etc from drops and splashes of paint to be cleaned to the statisfaction of Engineer-in-charge. (vii) Sample patch of 10 sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work.

S&F LED light fitting 1x18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all fixing arrengenment complete all as specifieds and directed . .

S&F energy saving new generation 10W LED bulk head luminaire with opal diffuser, IP 65 and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 Hz complete all as specified and directed.

All as per Srl item No.112 here-in-before but for one three pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed

S&F MCB SPN, 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F MCB Single pole, 6 to 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F Submain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathed FRLSH copper wire 6 Sqmm for continous earth wire drawn into and including concealed PVC conduit of suitable size complete all as specified and directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall/ceiling and or in floors complete all as specified and directed

All as per Srl item No 112. here-in-before but for one socket outlet, 3 Pin 5 Amps, 230 Volts on independent board complete all as specified and directed

All as per Srl item No 112 here-in-before but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire complete all as specified and directed

S&F ceiling rose, surface backelite, two/three terminal, 240 volts complete all as specifieds and directed .

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dia light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specifieds and directed ..

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described to make surface even and smooth and apply putty & primer where required and applying one coats of synthetic enamel paint complete all as specified and directed.

S&F exhaust fan, steel body, AC single phase. 230 V of size 300 mm sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed

M&L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive excellent dirt pick up resistance with low VOC less than 50 Antifugal, Anti Algai properities in two coats @ 1.79 lites (undiluted) per 10 Sqm diluted with water as per manufacturer instructions applied over priming surface in between subsequent coats of paint (upto 4th storey with necessary scaffolding) complete all as specified and directed .

S&F Sheet metal enclosure for DBs,SPN, double door,IP-43 protected, 415 Volts,8 ways with 100 amps rated copper bus bar complete all as specified and directed

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

M&L for factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed.

S&F Galvanised steeI tubing, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 25 Sqmm, 4 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete including taking out old cable & bricks all as specified and directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

Disconnecting, dismantling and taking down carefully ACSR conductor of any size from LT/HT poles complete all as specified and directed..

S&F Sheet metal enclosure for DBs,TPN, double door,IP-43 protected, 415 Volts,4 ways with 100 amps rated copper bus bar complete all as specified and directed

specified and directed.

S&F MCB four pole, 40 to 100 Amp, 415 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

Dimantling and taking down old Insulators of any types complete all as specified and directied.

S&F pillar taps, chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed.

Dismantling and taking down old cross arms, clamps, braces, brackets of MS channel or angle section including nut bolts washers etc from poles complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 50 Sqmm, 3.5 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth in any type of soil for laying of cables, pipes etc. and getting out complete all as specified and directed .

Removing excavated material or surplus soil to a distance not exc 50 meter and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed .

M&L for factory made bus bar chamber of size 750 x 600 x 500 mm, outdoor type, pedestal type, powder coated, made out of 3.15 mm thick CRCA sheet duly powder coated, dust and vermin proof complete with openable shutter in front & rear having proper locking arrangement duly mounted on angle iron frame 50x50x6 mm including necessary earth work & PCC in foundation in all respect including aluminium bus bar mounted on insulator, 600 Amps, 4 pole, suitable for 3 phasex1 neutral, 415 volts, 50 Hz AC supply including control wiring to panel with suitable size of PVC insulated and sheathed copper cable with phase indicator lamps (R, Y. B) – 01 Set. complete all as specified and directed.

M&L for factory made bus bar chamber of size 750 x 600 x 500 mm, outdoor type, pedestal type, powder coated, made out of 3.15 mm thick CRCA sheet duly powder coated, dust and vermin proof complete with openable shutter in front & rear having proper locking arrangement duly mounted on angle iron frame 50x50x6 mm including necessary earth work & PCC in foundation in all respect including 100 Amp, 415 Volt,36 KA, 4 pole MCCB with thermal magnetic protection as incommer control and aluminium bus bar mounted on insulator, 500 Amps, 4 pole, suitable for 3 phase, 415 volts, 50 Hz AC supply including control wiring to panel with suitable size of PVC insulated and sheathed copper cable with phase indicator lamps (R, Y. B) – 01 Set. complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 10 Sqmm, 2.0 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

S&F thermoplastic polystyrene polycarbonate junction box of size 210 X 155 X 92 mm, shock proof with IP 66 protection with suitable connector for three phase loop in loop out branch out and vibration proof connection and fixing on LT/HT poles using MS clamp made out of 25mm x 3mm MS flat (02 Nos) and nuts & bolts of required size complete all as specified and directed

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 25 Sqmm, 4.0 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

S&F Galvanised steeI tubing, light grade, 80mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 70 Sqmm, 3.5 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

M&L for factory made bus bar chamber of size 750 x 600 x 500 mm, outdoor type, pedestal type, powder coated, made out of 3.15 mm thick CRCA sheet duly powder coated, dust and vermin proof complete with openable shutter in front & rear having proper locking arrangement duly mounted on angle iron frame 50x50x6 mm including necessary earth work & PCC in foundation in all respect including 400 Amp, 415 Volt,36 KA, 4 pole MCCB with thermal magnetic protection as incommer control and aluminium bus bar mounted on insulator, 500 Amps, 4 pole, suitable for 3 phase, 415 volts, 50 Hz AC supply including control wiring to panel with suitable size of PVC insulated and sheathed copper cable with phase indicator lamps (R, Y. B) – 01 Set. complete all as

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium solid conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sqmm 2 core nominal cross section in service connection complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 2.0 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

M&L in repair for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to GI strip 25x4mm by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 4.00 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,40mm dia medium grade galvanised steel tubing upto 7.5 m length for drawing earth strip protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 95 Sqmm, 3.5 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

M&L for cutting of bituminous road / floor for laying of pipe / cables, not exceeding 1.5 meter wide and not exceeding 1.5 meter deep including refilling the material ,watering, well ramming / compacting and making good with 100 mm thick PCC 1:2:4,type B-1 complete all as specified and directed.

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of 15mm bore or for unions and fixed complete all as specified and directed.