SPECIAL REPAIR TO BLDG NO P-504 AND P-102 AT AF STN AGRA

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles complete all as specified and directed.

M&L for brick work with burnt clay old size bricks,sub class B straight or curved on plan with mean radius n.exc 6m for built in CM 1:6. complete alll as spfd and as directed

Demoltion of RCC Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

M&L for RCC nominal Mix for slab aggragate 20mm size , 1:1.5:3 ratio supported on walls as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work with fair finished; not exceeding 200mm thick (Horizontal or sloping)all as complete all as specified and directed.

M&L for non skid ceramic coloured tiles 8 to 10 mm thick (square or rectangular) area of each tile exceeding0.18 sqm but not exceeding 0.38 sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6 for laying floor finishes and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed by EIC

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match & including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6 for laying floor finishes and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed by EIC

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6 for laying floor finishes and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed by EIC

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical surface, skirting , dado . set and jointed in neat cement slurry and pointed in white or coloured cement to match & including screed bed or bedding layer of mortar 10 mm thick in cement mortar 1:3 for laying vertical surface finishes complete all as specified and directed..

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting , dado , verical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match & including screed bed or bedding layer of mortar 10mm thick in cement mortar 1:3 for laying finishesand Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed by EIC

M&L for glazed ceramic coloured tiles of size 450 x 300 x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:3 on other than fair faces of brick wall finished rough to fix tiles and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed by EIC

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar (1:6) and pointing in white cement (1:2) using marble dust with admisture of pigment to match with shade of granite and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed by EIC

M&L for pre-polished machine cut Kota stone in stair case tread flooring 20-25mm thick laid over 20mm thick screed bed in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed by EIC (Note : only one stone piece on one tread with nosing one side)

M&L for pre-polished machine cut Kota stone slab in stair case riser 20-25 mm thick on vertical surfaces over 10mm thick cement plaster in (1:3) such as risers, skirting etc. jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and taking down existing skirting and Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed by EIC (Note : only one stone piece on one riser)

Taking down cement or cement lime plaster on walls/celling/chajja any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

M&L for rendering 15 mm thick in cm 1:4 mixed with Pidi Proof 101 LW (+) of Dr fixit or equivalent integral water proofing admixture @200 ml/bag of cement and finish the surafce even and smooth (without using extra cement ) completely all as specified and directed. Note: Pidi proof to be measured separately as supply only.

M&L for applying two coats of super latex 302 of Dr fixit (Pidilite) or equivalent in ratio (1:4:7) (one part super latex 4part water 7 parts of cement ) @1.5 Kg of homogenous mixutre /Sqm

M & L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings, colour patterns of stone chippings shall be same as adjacent existing surface and approved by Engr -in - charge in cluding taking out existing stone grit & plaster complete all as specified (Payment for providing grooves shall be made separately).

M&L for rendering 15 mm thick in cement mortar 1:6 and finish the surafce even and smooth (without using extra cement ) for internal walls completely all as specified and directed.

Material and labour for rendering/plastering, 10mm to 30 mm thick as required at site in cement mortar (1:3) , for repair of RCC chajja, roof projection, fin facia , balcony railing etc including applying neat cement slurry @ 3 Kg/sqm befor rendering , finishing surface even and smooth without using extra cement as specified Note :- The Rates are inclding Use of all scaffoldings up to 14 M ht of buildings .

M&L for rendering 10 mm thick in cement mortar 1:3 on concrete surface of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for preperation of newly plastered concrete surface of ceiling & applying three coat of white wash on ceiling surface complete all as specified and directed.

M&L two coats of distemper oil emulsion on newly plastered wall surfaces including preparation and 1mm thick wall care putty complete all as specified and directed.

M&L for applying three coats of white wash on new wall surface including preparation of surface complete all as specified and directed.

M&L for applying two coats of white wash on old wall surface including preparation of surface complete all as specified and directed.

M & L preparing old decorated surface of walls and applying two coats of distemper oil emulsion with 1 mm thick wall care putty to make smooth surface incl complete removal of existing treatment on walls all as specified and directed by Engr-in- charge

Complete removal of existing treatment wall surface all as specified and directed by Engr-in- charge

M&L for preperation of old plastered concrete surface of ceiling & applying two coat of white wash on ceiling surface complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old or new surfaces and applying putty 1mm thickness over plastered surface to prepare the surface even and smooth all as specified and directed by Engr-in- charge

Providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth

Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level) (unreinforced) complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2 (1:3:6) (using 40 mm graded stone aggregate ) as in plinth protection and path finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Taking up or down steel and connections including cleaning for refixing or removal to store 15mm bore complete all as specified and directed

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm bore complete all as specified and directed

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 25mm bore complete all as specified and directed

Supplying and laying of CPVC pipes in repair 16mm dia external SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified.

Supplying and laying of CPVC pipes in repair 20mm dia external SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified.

Supplying and laying of CPVC pipes in repair 25mm dia external SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fitting complete all as specified.

S&F in repair 10 Ltrs capacity, PVC valveless, syphonic action type, low level flushing cistern, white, with inlet, ball valve, float and handle complete with all internal accessories and fixed to wall, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC with and including 600 mm long PVC connection with 02 Nos PTMT nuts and rubber washer and making good to disturbed surfaces of wall or floor complete all as specified and directed.

S&F in repair S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified & directed.

S&F 32/40 mm dia Semi Rigid PVC waste pipe for wash basin with length not less than 700 mm complete all as specified & directed

S&F in repair stop valves/angle valve 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed .

S&F in repair bib taps, cast copper alloy, fancy type,long body chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, anti syphonage and providing cement concrete bedding as in repair complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device ®

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S&F in repair vitreous china wash hand basin white flat back size 550x400 mm including two Nos angle iron brackets including, 32mm dia PTMT waste coupling, complete all as specified and directed.

S&F PVC connections hot and cold 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair brass chromium plated shower roses with or without swivel joints 125mm size with CP long shank arm including fixing to steel pipe or union complete all as specified and as directed.

S&F in repair Chromium plated 20mm dia, D type,60cm long towel rail with towel racks fixed with & including CP brass screws & wooden/plastic cleats (min. weight 190gms) complete all as specified and directed.

S&F in repair CP grating 100 mm dia with or without hole complete all as specified and directed.

S&F in repair brass CP wall/sink mixer for mixing Hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed.

S&F in repair Vitreous China soap tray embedded in the wall fixed to plugs complete all as specified and directed.

S&F in repair position rotational moulded polyethylene triple layered water storage tanks 1000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position with and including ball valve 20 mm bore high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight not less than 210 grams) and dismatling of exisitng tank complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F plate rack with racks and guard bars made out of stainless steel minimum 1mm thick, over all size 750mm X 600X250mm and assembled with using brass nuts, bolts and washers complete all as specified and as directed.

S&F sheet glass corner self (of 3 tier )assembly consisting of 5.5mm thick sheet glass self 15cm radius with chromium plated bracket guard and rail and fixed with CP screws and wood cleats with wall complete all as specified and directed.

Brass CP mixer for mixing hot & cold water screwed down (15mm) for iron pipe and fixed FOR WASH BASIN AS SPECIFIED AND DIRECTED

Taking down chowkhats or frames with shutters (without taking off shutters from the frames exc 1.5 sq. m but n exc 4 sqm complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) n. exc 1.5 sqm complete all as specified and directed.

S&F solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in door opening but single sideprelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheetas per specification and drawings complete all as specified and directed .

S&F factory made solid panel PVC door shutter 30mm thick (style ) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded colour plain PVC or channel having a PVC sheet strip of 20mm width stuch in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F factory made WPC cupboard shutter /shelf / partition of required size, consisting of panel of 18mm (+ 0.70mm ) thick celuka PVC ply and for supportingthe hold of shelf / partition and shall provided 3 edges in size 18mm x 18mm as per required length. The front side of the edge vigible in the front of the shelf / partition to be edge lipped by 18mm x 1mm PVC sheet of density 600 kg / cbm manufactured by an ISO-9000 certified co., using solvent cement etc complete all as specified and directed.

S&F Factory made single extruded WPC (WoodPolymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant. complete as per manufacturers specification and direction of Engineer-in-Charge.

S&F 35 mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

S&F 35mm thk 2nd class Hard wood Kiln seasoned and chemically pressure treated glazed & skeleton shutters, open rebated at prepared to receive glass/gauze (without sash bars) edges of framing plain, chamfered, or rounded, fitted with and incl cut and mitred beads for securing glass, gauge etc, size of members of shutters as specified in SSR Pt-I, Sec-8, clause 8.24 (a) fixed to chowkhats complete all as specified and directed.

S & F magnetic catcher of approved quality in cub board and kitchen cabinet including fixing with necessary screws double strips (horizontal type ) complete all as specified and directed.

M & L for powder coated (any colour) anodized aluminium (sliding type) windows with three track bottom track size 92X29.5X1.5mm thick side and top track frame size 92X29.5X1.5mm and shutters powder coated aluminium anodized 39X20X2 mm thick (02 of glass and 01 of SS wire cloth) including necessry aluminium fittings like joint cleat glazing and gauging clips/strips / locking system and rubber packing anodized aluminium snap beading screws etc including all fittings & fixture complete all as specified and directed.

S & F window guard bar, angal iron for door chawkat ISI marked Framed work such as grills with making provision in grills for openable for desert cooler etc, gratings, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F powder coated (any colour) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified (minimum thickness of powder coating 50 micron).

S&F powder coated (any colour) anodised aluminium ventilator shutters, top hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified (Thickness or powder coating not less than 50 micron).

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with gauging clip/strip complete all as spd and directed.

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering including hold fast. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening complete allas specified and directed.

M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregated as in cill, step and for inserting hold fast of doors and windows all as specified and directed.

S & F 100 mm long medium weight, stainless steel hinges. complete all as specified and directed.

S&F aluminum anodized barrel tower bolt of extruded section size of bolt 150mm complete all as specified and directed.

S&F aluminum handle cast type anodized 150 mm size complete all as specified and directed.

S&F aluminium handle cast type anodized 125 mm size for kitchen cabinet , pvc door and bed room cupboard shutter complete all as specified and directed.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

M & L for brass Locks for cupboard, of grade I, size 65mm 2 levers complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) is 30 mm complete all as specified and directed.

M&L for two coat of synthtic enamel paint over a coat of primer in new steel surface including preparation of new Surfaces of any description, over 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed.

M&L for two coat of synthtic enamel paint in old steel surface including preparation of oldSurfaces of any description, over 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed.

M&L for two coat of synthtic enamel paint over a coat of primer in new woden surface including preparation of new Surfaces of any description, over 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed.

M&L for two coat of synthtic enamel paint in old woden surface including preparation of new Surfaces of any description, over 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed.

S & F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

Demolition and breaking up rain water pipe (PVC, AC, or re-inforced concrete ) of sice 100mm coplete all as specified and directed.

S&F PVC SWR pipes 110mm dia single socketed in any length with rubber ging joints fixed to wall complete all as spd and directed.

S&F 110mm bore PVC (SWR) bends any radius all as specified

S&F PVC SWR pipes 50mm dia single socketed in any length with rubber ging joints fixed to wall complete all as spd and directed.

Dismantling of cast iron pipe of 100 mm bore, set in cement mortar complete all as specified and directed

S&F 100 mm bore cast iron, spun cast soil, waste and vent pipes, in any length with or without ears with cement joints, fixed on wall complete all as specified and directed.

S&F 100 mm bore cast iron, spun cast soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches complete all as specified and directed.

Dismantling of cast iron pipe of 75 mm bore, set in cement mortar complete all as specified and directed.

S&F 75 mm bore cast iron, sand cast soil, waste and vent pipes, in any length with or without ears with cement joints, fixed on wall complete all as specified and directed..

S&F PVC SWR pipes 100mm dia single socketed in any length as in trenches/wall with rubber ging joints fixed to wall complete all as spd and directed.

S&F in repair CI bends 100mm bore ( any radius ), diminishing pieces or tapers (larger bore measured) of complete all as specified and directed.

S&F in repair CI bends 75mm bore ( any radius ), diminishing pieces or tapers (larger bore measured) of complete all as specified and directed.

S & F in repair CI vent cowl 100mm dia complete all as specified and directed.

S & F in repair CI vent cowl 75mm dia complete all as specified and directed.

S&F in repair CI branch pieces 100mm bore, single (equal or unequal), ordinary or inverted(spigot/socketed type) or with parallel branches with oval access doors complete all as specified and directed.

S&F in repairCI branch pieces 75mm bore, single (equal or unequal), ordinary or inverted(spigot/socketed type) or with parallel branches with oval access doors complete all as specified and directed.

M&L in repair Cast Iron long arm floor trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays. Including bolts & nuts & securing ends of stays to wall or roof for 100 mm bore pipe complete all as specified and directed.

M&L for pre-cast RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) cover slabs for man-holes etc set in CM (1:6) complete all as specified and directed.

Demolition of PCC of any description and any position not otherwise specifically provided for as specified and directed.

M&L for Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges, levelling course, Type B1 (1:2:4) (20 mm graded aggregate)

M&L 10mm thick plaster CM 1:4 mixed with Pidi Proof 101 LW (+) of Dr fixit or equivalent integral water proofing admixture @200 ml/bag of cement and finish the surafce even and smooth (without using extra cement ) completely all as specified and directed. Note: Pidi proof to be measured separately as supply only.

supply only water proofing compound (Make -Dr Fixit )

M & L for water proofing treatment to sunken roof with APP based polymeric membrane, 3 mm thick (minimum), weighing 3.5 Kg/Sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/sqm) shall be applied over and including applying one coat of hot blown bitumin grade 85/25 confirming to IS- 702 @ 1.2 Kg per Sqm over a coat of bituminous primer @ 0.3 litre per sqm surface, application of APP modified membrane joint shall be by torch application. The overlaps shall be minimum 100 mm on the transverse direction and 75 mm longitudinal direction complete all as specified and directed. Make : (i) SUPER THERMOLAY manufactrued by M/s STP limited. (ii) IWL (HYPERPLAS POLYSTER) manufactured by M/s IWL India Ltd. (iii) Pidilite Industries. (iv) M/S Sikka industries WP Shield

M&L for Cement concrete type E-2 1:5:10 (using 40mm thick graded stone aggregates as in foundations, sunken portion filling and mass-concrete complete all as specified and directed.

S&F in repair Stainless steel curtain rod made out of 25 mm dia pipe having wall thickness 1.20 mm with two Stainless steel SS grade 304 brackets fixed with SS screws and PVC sleeves complete all as specified and directed.

S&F 150mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

M&L in for roof treatment with following specification completely , complete all as specified and as directed by Engr-in - charge (i) Cleaning existing surface and taking down water proofing treatment properly with steel wire brushes (ii) Applying evenly a tak coat of bitumen primer @ 0.3 kg / sqm (iii) Applying a coat of hot blown bitumen 85 x 25 confirming to is - 702 @ 1,2 kg / sqm (iv) Applying and laying 3 mm APP modified memberane weighting not less than 3 to 4 kg / sqm in 100 mm over laps both longitudinally and transverrsally and overlaps to be sealing by torch , memberane shall be taken up to the thickness of slab / front fascia (v) The memberane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3

M&L for PCC Tiles 300x300x 20 mm thick laid over 15 mm thick cement mortar 1:6 mixed with 5% integral water proofing compound by weight of cement finished neat slurry complete all as specified and directed (Note :- WPC shall be paid incliding in this item)

M& L for one coat of aluminium paint over the APP membarene @ 0 .11 kg / sqm complete all as specified

M&L for cutting grooves in brick parapet walls, 75mm wide and 65mm deep and shaping horizontal face of groove for inserting APP membrane and sealed complete all as specified and directed

Dismantling Plain or corrugated Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified and directed

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof vering/cladding to wall, fixed with self tapping screws as specified

Dismantling timber scantlings 40 sq. cm and over in section, in any position all as spfd and directed by EIC.

S &F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats Fe-290(Gde E-165)all as spfd and directed by EIC.

M&L Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft loose soil complete all as specified and directed.

M&L Cement concrete Type D-2( 1:4:8) (40 mm graded aggregate)as in foundations,filling and mass concrete complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; included 75 mm thick PCC 1:4:8, type D2 (using 40 mm crushed stone aggregate) as in sub base including demoliation of existing concrete path of any discription complete all as specified and as directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

M&L for point wiring complete for one light/fan/ exhaust fan point controlled by one, one way 5 Amp switch with PVC (FRLSH) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including minimum 20 mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including anodised pressed steel concealed terminal switch boxes not less than 1.20 mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLSH) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including cutting chases for concealed piping and making good disturbed surface to match the existing surface complete all as specified and directed.

All as per srl item No 131 above but for call bell point complete all as specified and directed.

All as per srl item No 131 above but for 5 pin 6 amps socket outlet independent board complete all as specified and directed.

All as per srl item No 131 above but for 3 pin 6 amps socket outlet on the same board with other switch complete all as specified and directed.

All as per srl item No 131 above but for one light point controlled by two Nos 2 way switches complete all as specified and directed.

All as per Item No 131 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50 Sqmm and green colour earth cable of size 2.50 Sqmm.

M&L for point wiring complete with PVC (FRLSH) insulated unsheathed multistranded copper conductor of size 4 sqmm nominal cross sectional area single core drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, complete including 4 sqmm nominal cross sectional area PVC(FRLSH) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including cutting chases for concealed piping and making good disturbed surface to match the existing surface complete all as specified and directed.

S&F in replacement switch piano flush type one way 6 amps SP 230 volts complete all as specified and directed.

S&F in replacement switch piano 2- way, 6 amps flush type 230 volts complete all as specified and directed.

S&F in replacement bell push flush type 6 amps SP 230 volts complete all as specified and directed.

S&F in replacement switch in replacement piano flush type one way 16 amps SP 240 volts complete all as specified and directed.

S&F in replacement socket outlet 2 in 1, 3 pin 5/6 amps flush type 240 volts complete all as specified and directed.

S&F in replacement socket outlet 2 in 1, 6 pin, 5 and 16 amps flush type 230 volts complete all as specified and directed.

S&F in replacement bell ding dong AC , 230 VOLTS, single pole complete all as specified and directed.

S&F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S&F in replacement ceiling fan regulator, electronic stepped type 5 stage speed regulation, ISI marked complete all as specified and directed.

S & F anti Sucide fan rod(12") ISI marked white MS pipe zinc plated, 19mm OD 1.8+/- 0.05mm thick, spring set grade 3 carbon steel material zinc plated, MSME tested for performance test and opening at impact load of 22kg + and spring" hidden in the piper will expand to about 1mtr or more, and fixing of existing fan including connecting twested flexible wire from ceiling rose to fan including taking down old unserviceable ciling fan rod, dismantling electric connection complete all as specified and directed. (Make: Gold Life)

S & F in replacement lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S & F sheet metal single pole and neutral enclosure with socket, plug top complete with one single pole MCB of 20 Amps, 240 volts complete all as spd and directed.

S&F in replacement existing U/S light fitting with energy saving decorative LED batten 20 watt (4 Feet), 230 voltas, energy efficient tube light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffusre & integrated electronic driver complete with all accessories prewired and includeing making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed. Note:- Power factor should not be less thtn 0.95

S & F in replacement of old U/S bulk head light LED light fitting 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

Supply and fixing LED in replacement of old U/S light fitting mirror type with high out put diffuser 1 feet, 5 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F for replacement of existing unsv security light fittings with LED security light fitting 30/36 Watts, excellent thermally managed pressure die cast alumnium come with in-built photo sensor for automatic on/off, IP-66 including GI bracket made out of GI pipe 40 mm bore medium grade bent to an angle of 135 degree and reduced at the end to 32 mm dia, 1.20 mtr long including 2 Nos clamps, suitable size of nut, bolts complete all as specified and directed.

M&L for taking down carefully existing ceiling fan/exhaust fan for greasing / oiling of ball bearings / bushes and making it for smooth and noise free operation and painting with Hi-Gloss synthetic enamel paint of approved shade by spray painting after filling cavaties and re-fixing after providing new fan clamp, nuts/bolts, washers, down rod as required and provision of 3 core copper flexible cable of size 1.0 Sqmm from ceiling rose to fan connector complete with writing of MES No. on the fan surface all as specified and directed.

Dismantling of existing meter panel board removing existing energy meter keeping safe custody and refixing after complete the work including fixing in wall complete all as specified Engr in charge

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection single pole and neutral 240 volts, 8 way, including suitable size copper bus bar and neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S & F in replacement of MCB single pole 240 volts, 'B' curv of rating from 6 to 32 amps, with rupturing capacity 10 KA,including providing thimble for out going cables.

S & F in repair sheet metal enclosure VTPN duble door with suitable size of bus bar TPN 8 way as per IEC-61439-3, with neutral bar, earth bar and cable ties for cable management complete all as specified and directed

S & F MCCB 125 AMP 4 pole 415 volt, 16 KA complete all as specified and directed

S & F in replacement MCB DP 240 volts, 'B' curv of rating from 40 amps, with rupturing capacity 10 KA,including providing thimble for out going cables.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6 sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 1.5 sqmm nominal cross sectional area and one run of1.5 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

M&L for removal of existing old unsv earthing complete and providing new earthing with galvanised steel earth plate electrode, 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, GI tubing 15 mm bore medium grade protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal, salt complete all as per SSR with PCC chamber, 50mm thick RCC cover in 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bar @ 80mm c/c both way including earth work in any type of soil , removal of surplus soil to a distance n.exc 50 m and connecting, testing on completion all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).