Special Repair of Doctor Residences in Campus of CHC at Ratia in Fatehabad Distt. (Recalled)

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing (HSR 8.5 (b) in cement

Removing door and window (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantlled (HSR 8.18 (a) doors

(b) Windows

Dismantling cement conglomerate/ terrazzo floors 25 mm to 50 mm thick including concrete base (HSR 8.25)

Scraping of white wash and colour wash (HSR 8.32 (a)

Scraping of cement plaster (HSR 8.32 (c )

Cement concrete 1:8:16 with brick ballast 40 m nominal size in foundation and plinth (HSR 10.26)

Providing and Laying 60 mm thick ISI marked interlocking paver blocks (conforming to IS 15658 : 2006) of all shapes and colours of design mix cement M-35 over a bed of 25 mm thick fine sand mortar complete in all respect (HSR 10.158)

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level (HSR 11.9)

Tile terracing with one layer of tiles, 22.86 cm x 11.43 cm x 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1:3 and top surface to be left clean (HSR 13.14)

Cement concrete 1:2:4 gola 10 cm x 10 cm quadrant along junction of roof with parapet wall finished smooth where specially specified. (HSR 13.64)

Providing and Fixing vitrified tiles of 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles (HSR 14.89) Note: - Tile shall be to premium quality (first quality) of reputed manufacturer like NITCO, KAJA-RIA, SOMANI, ORIENT, JOHNSONS & RAK

Providing and Fixing vitrified tiles of size 600 x 600 mm of approved make in skirting/ dado laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles (HSR 14.90) Note: - Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJA-RIA, SOMANI, ORIENT & JOHNSONS

Pvdg & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thickcement coarse sandmortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Not : Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJA-RIA,SOMANI, ORIENT & JOHNSONS shall be used as approved by Engineer-In-Charge. (HSR 14.91) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing 1st quality ceramic glazed wall tiles condirming to I.S 15622 (thickness to by specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. b) size of ceramic glazed tiles 300 x 450 mm NITCO, KAJA-RIA,SOMANI, ORIENT & JOHNSONS shall be used as approved by Engineer-In-Charge. (HSR 14.92 (b) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Laying and fixing Granite stone in all shades 15 mm to 18 mm thick in flooring, laid in any pattern as spacified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone. (Excluding the cost of granite stone) (HSR 14.96)

Plastering on wall 12 mm thick cement plaster 1:6 (HSR 15.7)

Applying pink primer or aluminum priming coat on woodwork including preparation of surface, knotting and stopping etc (HSR 16.2)

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.5)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Providing two coats of exterior acrylic emulsion paint (HSR 16.79 (b) Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge

Providing and fixing plywood, plain lining, butt-jointed, including wooden plugs (teak) placed at 45 cm to 60 cm centres, complete with necessary nails (frame work shall be payable extra (HSR 17.47 (b) 6 mm thick decorative ply wood with teak faced on one side.

Providing and fixing flat pressed single or 3 layers particle board of B.W.R. grade (medium density) in plain lining butt, jointed including wooden plugs (teak), placed at 45 cm to 60 cm centres, complete with necessary nails (frame work shall be payable extra) (HSR 17.48 (b) 19 mm thick

Supplying and fixing hydraulic door closer I.S.I. mark, with necessary screws, etc. complete (HSR 17.82 (a) I.S.I. designation No. 1 (size of door upto 700 mm)

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy & chapllash etc. (non coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/ cleats, stops, nails etc. complete, fixed in position (excluding the cost of any fittings, other than speified above, but including labour for fixing the same in position (HSR 17.90 (b) - 17.18 (i) note 35 mm thick

Factory manufactured wire gauze door and window shutter of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other than teak, conforming to I.S specification no. 1003, kiln sea soned) with 100 mm wide vertical styles 150 mm wide lock rail 200 mm wide bottom rail wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position) a (ii) 35 mm thick HSR 17.92 ii - note I under 17.18)

Factory manufactured solid flush door shutters, with block board core as der I.S. No. 1659-1669 bonded with water, proof type danol formaloehyde synthetic resin, hot-press as , conforming to I.S. 2202 part-I and II fixed in position including iron hinges screws chocks/cleats and stops, etc. (Excluding the cost of any fittings other than specified above, but including labour for fixing the same in position):-( Note) Commercial veneering with vertical grains or cross bands and face vaneer on both sides comercial facing with laminated core and lipped edges HSR 17.93 (a) iii 35 mm thick - Note I under 17.18

Providing & Fixing Polish on Kotah Stone / Terrazzo complete in all respect as per PWD Sepcification (NS)

Providing and Fixing parking shed of japani sheet as per approved color with 25 mm thick square MS tube frame of 450 x 450 mm spacing and outer support with 50 mm square tube and vertical post 75 mm dia MS pipe with cement concrete 1:2:4 foundation including cutting, welding, all size screws, nut bolt and placing in position as direction by Engineer-In-Charge (NS)

Public Health Work Providing and fixing in position best indian make european type water closet suite with concealed 'P' or 'S' trap with or without vent (as approved by the Engineer-In-Charge) and all other necessary fitting as fully described in Item No. 30.3 above (HSR 30.6 (i) white

Extra over item Nos. 30.1 to 30.4 and 30.6 for providing and fixing 15 litres capacity vitreous china high level cistern complete with internal brass fittings instead of 12.5 litres capacity hihg level C.I. cistern complete (as approved by the Engineer-In-Charge) (HSR 30.8 (ii) Single Colour

Providing and fixing in position best indian make (ordinary) lavatory suites consisting of :- Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary. (HSR 30.41) white (i) R.S or C.I brackets for building into wall including painting 32 mm C.P brass waste with C.P brass chain and rubber plug 15 mm C.P brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-charge) All fittings best Indian make and; to the approval of the Engineer-in-charge All brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fitting etc. Size 450 x 300 mm with one no. tap

Providing and fixing in position best indian make pedestal fittings of vitreous chinaware complete (as required by the Engineer-In-Charge) (HSR 30.44) (i) White

Providing and fixing in position of best quality stainless steel sink of 600 mm x 450 mm x 200 mm size (for estimating purpose only) (HSR 30.53)

Providing and fixing in position best indian make shower with 15 or 201/D in-let (HSR 30.66 (c) C. P. brass with revolving joint

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc. (HSR 30.70 (a) C.P. Brass (i) Soap dish Large.

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc. (As per item no 30.41) (HSR 30.71) (a) Indian make (I) 600 mm x 450 mm

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) (HSR 30.75) (a) Bib cock long body

Providing & Fixing in position automatic brass ball valves in tanks (HSR 30.110 (b) with plastic ball (ii) 20 mm internal diameter

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. (HSR 30.119) 500 Ltr. Cap.

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : (DSR 18.11). (ii) 20 mm internal diameter of pipeline

Providing and fixing gun metal gate valve with C.I. Wheel of approved quality (Screwed end). (DSR 18.17) (c) 25 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New Work). (DSR 18.46) 20 mm internal dia

A B S CONSTRUCTION COMPANY

M/S Pritam Kumar Contractor