PROVISION OF 02 TOILET BLOCKS AT A B COY OF TB I MEG UNDER OF GE NORTH BANGALORE

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard / dense soil etc complete all as specified and as directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in hard / dense soil etc complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and as directed

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point etc complete all as specified and as directed

M&L for plain cement concrete 1:4:8 type D-2, with using 40 mm grades stone aggregates as in foundations and mass concrete etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in Foundation, including rafts, footings, plinth beam etc complete all as specified and as directed

M&L for Reinforced cement concrete M-25 (Design mix) with using 20 mm graded stone aggregates as in slab supported on walls, beam and columns in floors, roofs landing balconies canopies etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in beam, cantilevers, bressumers, lintels over 1.5 mtr span etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) design Mix with using 20 mm graded stone aggregates as in col, pillars, piers, posts and struts etc complete all as specified and as directed

Supply only Liquid water proofing compound

M&L for Pre-cast cement concrete block masonry, Type C1 1:3:6 (20 mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:6 , complete etc

M&L for Providing precast cement concrete, Type C1 1:3:6 (20 mm graded aggregate) solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar in CM 1:6, complete, in walls, complete etc complete all as specified and as directed

M&L for Cutting chases, pinning in Stone, concrete block or slab walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth etc complete all as specified and as directed

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to etc complete all as specified and as directed

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) with Rough finished surfaces of concrete (Flat) etc complete all as specified and as directed

M&L for formwork to sides and soffits of floor or roof beam, beam and haunching, girders, bressummers, lintels cantilevers, shelves including supports, overhangs etc also splays between floor and beam with rough finished etc complete all as specified and as directed

M&L for formwork to sides of pillars, posts, struts, piers, col and stanchions, for square, rectangular or polygonal, rough finished surfaces of concrete etc complete all as specified and as directed

S&F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face etc complete all as specified and as directed

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) etc complete all as specified and as directed

S&F Powder Coating (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified and as directed

S&F Powder Coating (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, swindow and ventilator shutters, or top hung type sliding type without sash bar, aluminium section weighing not less that 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all as specified etc. complete all as specified etc. complete shall as specified and as directed

S&F 4mm thick Figured glass, pin head type and glazing with oil putty in squares in not. exc 0.5 sq.m in each pane etc omplete all as specified and as directed

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire stapel etc complete all as secified and as directed

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F for 100mm butt hinges, heavy weight, Stainless Steel and fixed complete as sepecified and directed

M&L for framed work as in grills, grating etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars barred iron doors, ladders framed balusters walks ways, railing framed work of water tanks and similar work etc complete all as specified and as directed

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed

All as per item No 27 above but 6 to 8 mm dia etc complete all as specified and as directed

All as per item No 27 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed

M&L for 75 mm thick cement concrete (1:4:8) type D-2 with using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified and as directed

M&L for cement concrete type B-0 1:2:4 (12.5mm graded stone aggregates) 25 mm thick as in sub base of flooring etc complete all as specified and as directed

M&L for screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and as directed.

M & L for Non Skid ceramic tiles coloured 7 to 8mm thick (square/rectangular) area of each tile exc 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed

M&L for exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. complete all as specifed and as directed

M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and as directed

M&L Glazed ceramic tiles coloured 300mmx 450mm, 6 to 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and and as directed

M&L for 20mm Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. etc complete all as specified and directed.

M&L for rendering for ceiling 5 mm thick in CM 1:3 on fair faces of brick work or concrete surface finished even and smooth without using extra cement etc complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:4) on other than fair faces of brick work or concrete surface mixed with water proofing compound as per manufacture instruction finished even and smooth without using extra cement etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surface finished and smooth without using extra cement etc complete all as specified and as directed

M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed

M&L for preparing newely plastered surface of ceiling and applying three coat of white wash etc complete all as specified and as directed

M&L for preparing newely plastered surface of wall and applying three coat of white wash etc complete all as specified and as directed

M&L for preparing newely plastered surface of wall and applying two coat of cement base paint over a coat of primer etc complete all as specified and as directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

S&F 20 mm dia bore CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F 25 mm dia bore CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F rotational moulded PVC water storage tank 1000ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completg all as specified and as directed

S & F 25 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed [Minimum weight for 20 mm – 210 gms] .

S & F 25 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe etc complete all as specifieid and as directed

S&F bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F 15mm dia bore pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and as directed

S&F stop valves /Angle Stop cock fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed

S & F PVC connection 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

S&F PVC urinal waste pipe 32mm dia 800mm long, complete all as specified and directed

S&F viterous china squatting pan orrisa pattern of size 580X440 mm white with integral foot rest 'P' trap including connecting to trap and flush pipe anti-symphonage pipe etc complete all as specified and as directed

S&F PVC flushing cistern with flush out valve low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets, etc complete all as specified and as directed

S&F vitreous china wash basin white, flat back, size 550 x 400mm excluding taps, waste, chain & plug and porcelain stopper but including brackets, 32 mm bore waste stainless steel coupling and LDPE pipe 600 mm long complete all as specified and directed.

S&F Viterous China urinals, bowl type (back or corner wall type), including providing and fixing plugs, beddings urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe 40 mm bore waste stainless steel coupling and LDPE pipe 600 mm long

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

M&L for rendering 10 mm thick in CM (1:3) on fair faces of brick work or concrete surface mixed with water proofing compound as per manufacture instruction, finished with fair and even etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

M&L for applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017, 3mm thick and weighing not less than 3.60kg/Sqm reinforced with non woven polyster/HMHDPE matt black finished over compatible primer/bonding bitumen @ 0.40 Litr/Sqm and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer's instructions and applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sqm complete all as specified and directed. complete all as directed.

S&F 75 PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement etc complete all as specified and as directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

S&F 150mm dia bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floors et ccomplete all as specified and directed

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 with using 12.50 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:6 complete all as specified and directed.

S&F 110mm PVC (SWR) pipes, single socketed in any length with rubber ring joint leaid in trenches or in floor complete all as specified and directed

All as per item no.73 above but 75mm bore pipe complete all as specified and directed

S&F 110mm PVC (SWR) pipes, single socketed in any length with rubber rings joint fixed with wall complete all as specified and directed

All as per item no 75 above but 75 bore pipe complete all as specified and directed

S&F PVC (SWR) bends (any radius) of 110mm dia.

S&F PVC (SWR) bends (any radius) of 75mm dia.

S&F 110 mm dia PVC (SWR) branch pieces, single (equal or unequal), Single Y equal or unequal etc complete all as specified and as directed .

All as per item No 79 above but 75 mm dia bore

S&F PVC (SWR) vent cowls of 110mm dia.

Spreading and levelling in well layers not exc 25 cm thick including watering as required etc complete all as specified and as directed

M&L for Hard core with broken stone or boulder of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15 cm thick water and rammed to a true surface etc all as specified and as directed

M&L for 75 mm thick PCC 1:3:6, type C-1, using 20 mm graded aggregates as in plinth protection etc, finished even and smooth without using extra cement complete all as specified including joints filling with sealing compound Grade "A" complete all as specified and directed.

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed

Excavation in trenches in hard/dense soil, not exc 1.5 mtr wide and n exc 1.5 mtr in depth; for foundation, laying pipes/elect cables etc, and getting out.

Supply and spread river sand to required width at bottom and top for cable cushioning (not less 18 cm thick in layer after punning) all as specified in SSR Part-I.

Supply and lay common burnt old size bricks of sub class B laid at right angle on the cable complete in trenches for cable protection complete all as directed by Engr-in-charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified in soft / loose / hard / dense soil.

Removing excavated materials of soil not exc. 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point

M&L for providing trenchless bore using mechanical pneumatic drilling equipment for passing electric cables through HDPE pipe of 80mm dia under the existing bituminous/WBM road/PCC hard standings, depth range not less than 1.0 mtr and upto 1.5mtr and making good to the distrubed surfaces of road to match with its existing specifications all as specified and directed by engr-in-charge at site. Note : 1. Quoted rates deems to be inclusing of necessary earth work, transportation charges of Drilling machine, and cost of HDPE pipe and passing pipe through bore complete. 2. Any damage to MES assets caused during trenchless bore shall be recitfied by the contractor at his own cost.

Mild steel galvanized pipe light grade for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified for size of 40mm bore dia.

M&L for laying, jointing, testing cable XLPE insulated, armored and PVC sheathed LT 1100 volts grade and aluminum conductor confirming to IS 7098 laid in trenches/through pipe/floor/fixed wall etc complete all as specified and directed for size of cables 10 Sqmm 2 core stranded conductor

Point wiring complete concealed with 1.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including non metalic rigid PVC conduit medium grade ISI marked including accessoires (a) One light point/ Exhust fan point/controlled for one switch.

(b) One switch socket combination outlet 2/3 pin, 5 Amp on independent board

Point wiring complete concealed with 2.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including non metalic rigid PVC conduit medium grade ISI marked including accessoires

Switch piano, flush button single pole, 5 Amps one way.

Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC square blocks.

Switch sokcet combination flush type 5 Amp 2/3 pin muliti purpose.

Switch socket combination flush type 5/15 Amps 3/3 pin universal multipurpose.

S&F Exhaust fans AC single phase 230/240 V of size 250/280/300 mm sweep with louvers fixed outside with all accessories and fixing the exhaust fan from ceiling rose with 3 core flexible copper wire 24/0.20 sqmm, etc all as directed. Make : Bajaj

S&F LED batten suitable for indoor applications 20 Watts, 2 feet with polycarbonate housing & integrated LED channel with white arcylic cover complete with all accessories including taking out old fittings all as specified and directed. Make: Bajaj, Cat No. BCLAB 20 WHLED

S&F LED batten suitable for indoor applications 10 Watts, 2 feet with polycarbonate housing & integrated LED channel with white arcylic cover complete with all accessories including taking out old fittings all as specified and directed. Make: Bajaj, Cat No. BCLAB 20 WHLED

Sheet metal enclosure (ISI marked) distribution board for 240 volts, 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

MCB single pole 6 to 32 Amps 240 volts, 10 kA rupturing capacity providing in DB complete all as specified.

MCB single pole & neutral 6 Amps 240 volts, 10 kA rupturing capacity providing in DB complete all as specified.

Supply and fixing 30 W LED bldg security light fitting with pressure die cast housing along with prismatic polycarbonate difuser with IP 60 protection including taking out old fitting. Make:- Bajaj Cat part No. ENXTP 30L WHSYPC SD or equivalent

S&F Bracket make out of GI tubing medium grade 25 mm bore, approx length 1.5 m long including MS clamps made out of MS flat iron 25x6 mm, nuts bolts, washers etc and including before fixing applying two coats of aluminum paint over a coat of red oxide.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cmx6mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connecting with steel GI earth wire 4mm dia by means of bolt nut check nuts and washers including PCC pit with 1:2:4 type B-1 using 20mm graded stone aggregate and frame cover of angle iron 25x25x6mm, MS sheet 3mm thick, and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering common salt chorcoal funnel wiremesh, earthwork in any type of soil returning filling in and removal of soft/loose soil to a distance n. exc 5 mtr including earth test point and making connections, testing on completion all as per electric plate No 5 of SSR Part-I and directed by engr-in-charge at site.

M&L taking branch connection from existing distribution GI pipe of bore dia of 50mm including, cutting, threading, inserting GI fittings i.e socket, nipple, union and unequal size Tee to take branch connection of 40 mm bore dia all as directed by engr-in-charge at site.

Supply & laying & fixing GI pipe medium grade size 40 mm bore with all necessary fittings fixing on wall ceiling or laid in trenches/under floors.

Supply & laying & fixing GI pipe medium grade size 20 mm bore with all necessary fittings fixing on wall ceiling or laid in trenches/under floors.

M&L for gun metal gate valve with iron wheel head screwed both ends for iron pipe fixed for size 25 mm bore dia.

M&L for gun metal gate valve with iron wheel head screwed both ends for iron pipe fixed for size 20mm bore dia.

M & L for Valve Chamber in brick masonry foundation in 1:3:6 PCC, size of chamber 45x45x45cm and provided locking arragement valve pit cover of made of 3mm thick MS sheet, including necessary earth work all as specified and as directed.

OM CONSTRUCTIONS

ARATHEERTHA CONCEPTS

S S BUILDERS

VIKAS CONSTRUCTIONS

Elite Constructions

Sangam Construction

S SUDHAKAR

Eeguchi Constructions