PROVN OF 03 X TOILET BLOCK AND BATHROOM ATTACHED WITH BLDG NO E-97, E-98 AND 02 X CAR/SCOOTER PARKING SHED AT OFFICE AREA, PT GROUND AND OTHER SANCTION WORK OF AGE B/R-II UNDER GE (EAST) LUCKNOW

Amount

Excavation in trenches not exc 1.5m wide and not exc 1.5M in depth for foundation etc and getting out in soft/ loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/loose soil, each not exc 0.5 cum (0.55mX0.55mX1.5m deep), getting out, and removing soil to a distance not exc 50mcomplete all as specified and directed.

Returning filling including spreading, levelling, watering and well ramming in layers not exc. 25cm complete all as specified and directed.

Removing excavated material not exc 50 m and depositing, where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Surface excavation soft/loose soil not exc 30 cm deep and averaging 15cm deep and getting out soil complete all as specified and directed

Earth filling under floor, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling/sub-base to floor, etc and mass concrete filling complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in foundation/footing, drain etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in copings, bed plates, plinth courses, parapets and the like including weathering, slightly rounded or chamfered angles and throating including use and waste of necessary form work etc complete all as specified and directed.

M&L for steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS-1161-1998 Gde St 240 complete all as specified and directed.

S&F for rolled mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

M&L for steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and directed.

S&F MS screw bolts 12mm dia (Machine Made ) with hexagonal or square heads at one end and screwedat the other end or screwed both ends,each screwed end to be fitted with washers and one ehexagonal or square nut, diameter of shank 11 to 15 mm, length of bolt not exc 5 cm long complete all as specified and directed.

M&L for brick work with sub class B fly ash bricks burnt straight or curved on plan exc 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius as in half brick thick wall built in CM 1:4 complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description not otherwise described over 10 cm width or girth, and applying two coats of synthetic enamel paint over acoat of red oxide primer complete all as specified and directed.

S&F prepainted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering,cladding to wall etc, fixed with self tapping screws , complete all as specified and directed.

S&F prepainted galvalume zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, fixed with self tapping screws complete all as specified and directed.

M&L for hard core of broken stone or boulders aggregate of guage not exc 63 mm deposited, spread, levelled and rammed to true surface complete all as specified and directed.

M&L for PCC 1:3:6 type C-2, using 40mm graded stone aggregate as in foundation, filling and mass concrete etc complete all as specified and directed

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base of floor complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection laid in bays not exc 1.5m with expansion joints 30x10mm filled with mixture of hot bitumen and sand, finished the surface even and smooth without using extra cement complete all as specified and directed

M&L for precast concrete coloured rubber moulded Paver block any shape and size conforming to IS 15658-2006 of 80mm thickness,M-40 grade in set jointed and pointed with grey cement slurry and pigment to match the floor approved design /colour set and bedded over and including 25mm thick coarse sand laid over compacted sub soil complete all as specified and directed.

M&L for cement concrete type B-1 1:2:4 as in cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over as in reinforcement cut to length, bent in shape required including cranking, bending, spirally hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8 mm dia and over as in reinforcement cut to length, bent in shape required including cranking, bending, spirally hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per item No 26 above but 5mm dia and over up to and including 10mm dia in stirrups, spacers and binders.

Taking down cement or cement lime plaster on brick walls etc including raking out joints, hacking for key scrubing down with water etc complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for plastering 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces, finished the surface even and smooth with using WPC @ 2% by weight of cement complete all as specified and directed.(Note- WPC shall be measured and paid separately)

M&L for 10mm thick cement plaster on other than fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth complete all as specified and directed

M&L for 15mm thick cement plaster on other than fair faces of brick work or concrete surfaces in CM 1:6 finished even andfair complete all as specified and directed

M&L for rendering 15mm thick on otherthan fair faces of brick work or on concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 as in ceiling ,soffits of slab and finish the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick cement plaster in CM 1:3 on top of RCC Roof Slab with using water proofing compound 3% by weight of cement, finish the surface even & fair complete all as specified and directed

M&L for glazed ceramic coloured tiles of size 600x300x 7-8mm thick including 10mm thick rendering in CM 1:4 on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and drected

M&L for non skid ceramic coloured tiles 400x400x 7mm thick in floors etc. including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Supply only integral water proofing compound (ISI marked) complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying three coat of white wash complete all as specified and directed

M&L for preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed

M&L for preparation of new plastered surfaces of wall including cornices etc and applying two coats of cement based paint (any colour as approved) complete all as specified and directed.

S&F 15mm dia tube medium grade galvanised, with all fitting and fixed complete to walls/ ceilings/ concealed or laid in floors complete all as specified and directed.

S&F 20 mm tube medium grade galvanised with all fitting and fixed complete to walls/ ceiling / concealed or laid in floors complete all as specified and directed

S&F 500 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top)in white colour triple layered, hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

S&F 1000 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top)in white colour triple layered, hoisted and fixed in position all as specified in SSR Part I including 20mm PTMT ball valve complete all as specified and directed

S&F 20 mm dia brass gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F vitreous China wash basin white (flat back or angle back ) type of size 550mmx400 mm including brackets,brass cromium plated waste fittings and pvc waste pipe including cutting for and pinning in ends of bracket complete all as specified and directed. .

S&F 15mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down hidh pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450/600 mm complete all as specified and directed.

S&F 32 mm waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement complete all as specified and directed.

S&F 32 mm bore Low density polyethylene pipes for Wash hand basin etc complete all as specified and directed.

S&F vitreous china urinals, half stall type (flat back), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including spreader, 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed

S&F vitreous china wash down water closet pan pedestal pattern, including P/S trap and connection to drain (or outgoing pipe) and pvc seat cover excluding flushing cistern and flush pipe complete all as specified and directed

S&F vitreous china sqatting pan, Orissa pattern, size 580 x 440 mm white , with integral foot rests including trap (excluding flushing cistern and flush pipe ) complete all as specified and directed

S&F 10 litre capacity ISI marked PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F 20 mm dia float valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe with fly nuts complete all as specified and directed.

S&F 15mm bore long body bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F15 mm bore stop valves (angle type) cast copper alloy chrominum plated fancy type screwed down high pre-ssure with crutch or but terfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement complete all as specified and directed.

S&F 110mm PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement complete all as specified and directed.

M&L soap dish with glass tray fixed to wall with plug and chromonium plated brass screw embedded in the wall complete all as specified and directed

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F CP brass toilet paper holder of superior quality complete all as specified and directed.

S&F CP brass Jet spray with hand hold arrangement including 1.5 m long flexible pipe with hook of superior quality complete all as specified and directed.

S&F stainless steel grating doom of 125 mm dia complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed

S&F 100/110 mm bore PVC (SWR) bends any radius complete all as specified and directed

S&F 110 mm bore PVC (SWR) junction single T, equal or unequal complete all as specified and directed

S&F 75 mm bore PVC (SWR) junction single T, equal or unequal complete all as specified and directed

S&F100/110 mm bore PVC (SWR) vent cowl complete all as specified and directed

S&F factory made PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube suitable for opening as per site condition complete all as specified and directed.

S&F factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed

S&F steel window or ventilator partly fixed and partly top hung with glazing bars complete all as specified and directed.

S&F 200 mm long Aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long aluminium handles, cast type, anodized and fixed complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight, stainless steel, and fixed complete all as specified and directed

S&F 4 mm thick Figured/sheet glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

S&F 16mm dia and 300mm long aluminium alloy anodised sliding door bolt with hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40mm graded stone aggregate as in bed of drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for 150mm dia of pipe complete all as specified and directed

M&L for 150 mm dia salt glzed stoneware drain pipes grade ‘A’ laid in trenches and jointed in cm 1:1 complete all as specified and directed.

M&L for providing pre-cast RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for man holes and drains) including necessary form work set in CM 1:4 complete all as specified and directed.(Note :- Reinforcement shall be measured and paid separately.)

Construction of septic tank for 50 users, excavation in ordinary soil, foundation In PCC 1:2:4, brick work in CM 1:4, RCC slab covers in M-25 including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete all as specified and directed as per drawing No. CELZ TD-217 Sheet No 1/2 & 2/2. Note:- Depth of septic tank shall be the effective depth i.e, below invert level of sewage line at well complete all as specified and directed

Construction of septic tank for 10 users, excavation in ordinary soil, foundation In PCC 1:2:4, brick work in CM 1:4, RCC slab covers in M-25 including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc., complete all as specified and directed as per drawing No. CELZ TD-217 Sheet No 1/2 & 2/2. Note:- Depth of septic tank shall be the effective depth i.e, below invert level of sewage line at well complete all as specified and directed

Construction of soakage well of size 2.40M dia X 4.50M deep, excavation in ordinary soil, foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete all as specified and directed as per drawing CELZ TD-576 Sheet No 1/2 & 2/2. Note:- Depth of soak well shall be the effective depth i.e, below invert level of sewage line at well complete all as specified and directed

Construction of soakage well of size 1.8M dia X 3.00M deep, excavation in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete all as specified and directed as per drawing CELZ TD-576 Sheet No 1/2 & 2/2. Note:- Depth of soak well shall be the effective depth i.e, below invert level of sewage line at well complete all as specified and directed

M&L for RCC 1:1½ :3 type A1(using 20 mm graded stone aggregate) as in foundations, footings, plinth beams; bases for columns, etc.complete all as specified and directed

M&L for RCC 1:1½ :3 type A1(using 20 mm graded stone aggregate) as in Column, pillars, piers, posts and struts etc complete all as specified and directed

M&L for RCC 1:1½ :3 type A1 (using 20 mm graded stone aggregate) as in roof slabs, shelves etc all as specified and directed.

M&L for RCC 1:1½ :3 type A1 (using 20 mm graded stone aggregate) as in chhajas complete all as specified and directed.

M&L for RCC 1:1½ :3 type A1 (using 20 mm graded stone aggregate) as in roof beam, bands, lintel beam etc complete all as specified and directed.

M&L for formwork to sides of concrete in foundations, footings, bases of columns, sides and soffits (if any) plinth beams, and similar work complete all as specified and directed

M&L for formwork to sides of concrete of pillars, posts, struts, piers, columns etc complete all as specified and directed.

M&L for form work to soffits of roof slabs, floor slabs and similar work not exc 200 mm thick fair finished surfaces (flat) complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for formwork to edges of concrete flats, roofs and sides of RCC/ PCC bands in walls, and similar work exc. 10 cm but not exc 20 cm wide complete all as specified and directed.

M&L for formwork to edges of concrete flats, roofs and sides of RCC/ PCC bands in walls, and similar work exc 5cm but not exc 10cm wide complete all as specified and directed.

M&L PCC 1:2:4, type B-0, with 12.5mm stone aggregate 40 mm thick in Damp Proof Course to horizontal or vertical surfaces including necessary formwork using water proofing compound as per manufacture's instruction and incl a coating of bitumen primer complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregates as in sub base of floors complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregates as in sub base of floors, finished the surface even and rough complete all as specified and directed.

M&L for salt glazed stone ware gully traps of 100x100mm size, square or round mouthed, type‘P’ complete all as specified and directed

M&L for sand filling under floors etc complete including watering & well ramming complete all as specified and directed

M&L for connecting 25 mm bore GI pipe from existing water supply line including necessary excavation , clamping making holes to existing pipe line complete all as specified and directed

S&F 25 mm bore galvanized steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed

M&L for cement concrete 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in foundations filling, sub base and mass concrete filling, etc complete all as specified and directed.

S&F machine made precast cement concrete blocks (interlocking pavers) rubberised finished coloured of 60 mm thick M-35 top layers of anti abrasive material over and including 50 mm thick sand cushion complete all as specified and directed. (Note:The interlocking tiles joint will be filled with fine sand)

S&F machine made precast cement concrete curb stone blocks using cement concrete 1:3:6 type C1 (20 mm graded stone aggregate) complete all as specified and directed.

M&L for one light / fan point controlled by one, one way switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick with 3 mm thick plastic laminated sheet top cover, brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed.

All as per item No 114 here-in-before but one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp.

All as per Item No 114 here-in-before but one 3 pin socket outlet, 15 Amps, independent with cable 2.5 Sq mm size.

All as per item No 114 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp.

All as per Item No 114 here-in-before but point wiring with 2.5 Sq mm single core FRLS cables and earth continuity wire of 1.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

S&F switch piano flush type, 06 Amp, single pole, one way, 230 Volt complete all as specified & directed.

S&F socket outlet 2 in 1, 5 pin, 06 Amp, flush type, 230 volt complete all as specified & directed.

S&F switch socket combination outlet 2 in 1, 3 pin, 06 Amp and 16 Amp flush type, universal, 230 volt, four hole complete all as specified & directed.

S&F lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting complete all as specified & directed.

S&F of single side connection LED T8 tube light rod 20 Watt, 6500K of four feet long into and including LED tube light fixture of four feet long with T8 push fit type holders, connector block, end caps, etc including connecting up complete all as specified and directed. Make : Crompton, Cat No : IGP131LT8-16& LT8-20-865-2 or Havells, Cat No : REGALBATTENT8UPT01X22WSSBS & PHOTONULTRA1213T8SSTL20WLED865SPC,philips cat no TMC 501P1XT-LED22W P 3241

S&F single side connection LED T8 tube light rod 8 Watt, 6500K of two feet long into and including LED tube light fixture of two feet long with T8 push fit type holders, connector block, end caps, etc including connecting up complete all as specified and directed.Make : Crompton, Cat No : DMLN1LT8-8& LT8-8-865-2 or equivalent in havells / philips

S&F LED security light fitting 45 watt, 5700K with IP 66 protection comprises of a pressure die cast aluminium housing, heat resistance toughened glass, LED lenses, surge protector, electronic driver, etc and all accessories pre-wired including connecting up with PVC insulated copper conductor cable 1.5 Sq mm, 3 core as required for connections and 32 mm bore light grade G. I. tube mounting bracket of 1.5 metre in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed. Make : Crompton, Cat No : LSTP-45-CDL or equivalent in Havells/ philips.

S&F ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed.

S&F sheet metal enclosure distribution board, single pole and neutral, AC, 240 volt, 04 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed. Make :-Legrand, Cat No. 5076 11 & 5079 13 or equivalent in Hager, Cat No : VYS04D & VYS04E or Schneider, Cat No : A9HSND04 & A9HSND074WB

S&F sheet metal enclosure distribution board, single pole and neutral, AC, 240 volt, 08 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK -09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed. Make :-Legrand, Cat No. 5076 11 & 5079 13 or equivalent in Hager, Cat No : VYS04D & VYS04E or Schneider, Cat No : A9HSND04 & A9HSND074WB

S&F MCB, SP, AC, 240 volt of 06 to 40 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. Make :-Legrand, Cat No. 4085 87 to 4085 95 or equivalent in Hager, Cat No : NCN106N to NCN132N or Schneider, Cat No : A9N1P06C to A9N1P32C.

S&F MCB, DP, AC, 240 volt of 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. Make :-Legrand, Cat No. 4086 36 or equivalent in Hager, Cat No : NCN232N or Schneider, Cat No : A9N2P32C

S&F exhaust fans single phase 230/240 Volts heavy duty metalicbody of size 300 mm sweep 1400 RPM including suitable louvers and making connection with twisted copper flexibelwire 23/0.076 mm all as specified and directed. Make/Model:- Havells Turbo Force SP 1400/ Orient 300 mm Heavy Duty/ Bajaj Heavy Duty Maxx Air

Supply, laying, testing and commissioning LT underground XLPE insulated, armoured heavy duty electric cable with aluminium stranded conductor, 1100 volt grade conforming to IS-1554 and ISI marked of cross sectional area 06 Sq mm 2 core size in trenches, on wall, road crossing through protection pipe etc. complete all as specified and directed.

Supply, laying, testing and commissioning LT underground XLPE insulated, armoured heavy duty electric cable with aluminium stranded conductor, 1100 volt grade conforming to IS-1554 and ISI marked of cross sectional area 10 Sqmm 2 core size in trenches, on wall, road crossing through protection pipe etc. complete all as specified and directed.

Providing sand cushioning with dry fine sand including filling, spreading, levelling in layers in cable trench with approved quality of sand for protection of under ground cable complete all as specified and directed.

Supply and laying 40 mm bore galvanised steel tubes with all fittings, light grade laid in trenches for cable protection complete all as specified and directed.

Supply and laying common burned clay bricks sub class B designation of old size bricks complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

M&L for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall complete all as specified & directed.

S&F of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall all as specified & directed.

S&F of stationery storage type electric BEE 5 star rated Hot Water Geyser of capacity 25 Ltr to operate on 230 volt AC, vertical type, white in colour, working pressure min 0.8 Mpa with glass lined coated tank, magnesium anode, adjustable thermostat, enamel coated incology heating element 2 KW, ABS plastic body,Product warranty-2 Years, Heating element warranty-4 Years, Inner Tank warranty-7 Years, including 4 nos full threaded fastner of size 100 x 10 mm with 2 Nos washer, complete all as specified and directed. Make: Racold/Jaquar/Havells/Bajaj/Crompton

Skyline Encon

M/S Reliance Construction

M/s Bhadoria Associates