SPECIAL REPAIR TO BLDG NO T-14 T-29 AND T-85 INCLUDING PROVN OF TOILET BLOCK AT CERTAIN UNITS UNDER AGE BR DETT-III AND AGE EM OF GE 862 EWS

Amount

Sch 'A' Part-I (B/R works) Surface dressing not exceeding 15cm deep in any type of soil complete all as specified and directed.

Surface excavation in any type of soil, n.exc 1.5m 30cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Excavating in trenches, n.exc 1.5m wide and n.exc 1.5m in depth in any type of soil for foundation, etc, or for shafts, wells, drain/water pipes laying of cables etc, n.exc 10 Sqm on plan and getting out, complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick ,complete all as specified and as directed.

Removing excavated material ,not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed.

Removing excavated material exceeding 5 Km but n.exc 10 Km and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D-2 using 40mm graded stone aggregates as in sub base, foundation, filling and mass concrete complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8, type D-2 using 40mm graded stone aggregates as in sub base of floors and mass concrete, complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:4:8, type D-2 using 40mm graded stone aggregates as in sub base of floors and mass concrete, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan and any radius in half brick thick wall, built in cement mortar 1:4, complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on fair/unfair faces of brick work or concrete surface, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surface (external surface), finished the surface even and smooth without using extra cement mixing with integral water proofing compound (as per manufacturer's instructions), complete all as specified and directed. (Note: Rate of WPC will be included in the quoted rate)

M&L for rendering 5 mm thick on concrete surface in cement mortar 1:3 on ceiling, finished even and smooth with sagol cement ,complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer over and including 3mm thick wall care putty, complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for 75mm thick plain cement concrete, type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 350x250x7mm or 450x350x7mm thick, (premium quality) on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

M&L for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, complete all as specified and directed.

S&F for factory made solid panel PVC moulded door shutter, 28 to 30mm thick (style) with 2,4 or 6 raised panel design with 2mm thick molded PVC sheet on the front face and 2mm plain colour PVC sheet on back face and supplying and fixing in the frame at site as per specification & drawing mentioned in SSR Part-II 2020, complete all as specified and directed.

S&F for 100mm long butt hinges medium weight, stainless steel, complete all as specified and directed.

S&F for aluminium anodized barrel tower bolts 150 mm long of extruded section (ISI marked) ,complete all as specified and directed.

S&F for extruded aluminium alloy handles size 150 mm fabricated type anodised (ISI marked), complete all as specified and directed.

S&F for vitreous China water closet (squatt pan) Orrisa pattern 680x470 mm size pan, white/colour, with front or back inlet with integral 'foot rests (PVC), (excluding flushing cistern and flush pipe) including connections to flushing cistern with flush pipe including provision of lime concrete, complete all as specified and directed.

S&F 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

S&F for vitreous China wash hand basin, white, flat back of size 550x 400mm excluding taps, waste chain and plug and porcelan stopper but including brackets and cutting for fixing brackets ,complete all as specified and directed.

S&F for vitreous China, counter top, wash hand basin, white, oval type of size 550mm including cutting for and pining in but excluding waste pipe, complete all as specified and directed.

S & F for 15 mm bore brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S & F brass CP wall mixer 2 in 1, two for hot cold water mixing and one for shower rose of 15mm dia screwed down for 15mm bore iron pipe and fixed, complete all as specified and directed by Engr-in-Charge.

S&F for vitreous China urinal, half stall type, premium quality white, including flush pipe and waste pipe with grating and union for discharge pipe (excluding flushing cistern) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement, complete all as specified and directed.

S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 500 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball brass valve with union screwed for iron pipe and fixed complete all as specifed and directed.

S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball brass valve with union screwed for iron pipe and fixed complete all as specifed and directed.

S&F for 15 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc, complete all as specified and directed.

S&F for 20 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc, complete all as specified and directed.

S&F for 25 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc, complete all as specified and directed.

M&L for 15mm bore angle valve, fancy type, chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed down high pressure, screwed for iron pipe or for unions and fixed, complete all as specified and directed.

M&L for 15mm bore stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed down high pressure, screwed for iron pipe or for unions and fixed, complete all as specified and directed.

S&F in repair for 15mm bore Stop valve (concealed type), chromium plated, cast copper alloy screwed down, high pressure with long shank and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F for 15mm bore bib tap, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete as in repair all as specified and directed.

S&F for 15mm bore fancy type pillar taps, cast copper alloy, with capstan heads, brass chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete as in repair all as specified and directed.

S&F for CP brass shower rose of size 125mm with swivel joints fixing to steel pipes etc, complete as in repair all as specified and directed.

S&F for PVC connection 15 mm x 600 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

M&L for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floor/ trenches, or fixed to wall, complete all as specified and directed.

M&L for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floor/ trenches, or fixed to wall, complete all as specified and directed.

M&L for 110mm bore PVC (SWR) Tee or branch piece single ordinary or inverted or with parallel branches but fitted with oval access door complete all as specified and directed.

M&L for 110mm bore PVC (SWR) bends with duck heel foot or heal rests, complete all as specified and directed.

M&L for 110mm bore PVC (SWR) bends complete all as specified and directed.

M&L for 75mm bore PVC (SWR) bends complete all as specified and directed.

S & F brass chromium plated tubular towel rail 20mm dia 600mm long with and including one pair of brass chromium plated bracket complete all as specifed and directed.

S&F for brass CP soap dish with chromium plated brass screws and wooden/plastic cleats, complete all as specified and directed

S&F for sheet glass shelf assembly consisting 5.5 mm thick, sheet glass shelf 12cm wide with chromium plated bracket guard and rainling 60cm long, complete all as specified and directed.

S&F glass corner shelf with tempered glass, stainless steel brackets and polished chrome finish rail, complete all as specified and directed by Engr-in-Charge.

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement and connecting to waste pipe, complete all as specifed and directed.

M&L for steel ventilators with top hung shutter including hinges, steel peg stay complete all as specified and directed.

S&F for 3 mm thick sheet glass ordinary quality and glazing with oil putty / wooden beads in squares n . exc 0.50 sqm in each pane, complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks or portion framed and hung as gates, including pintel hinges, stops, hand made sliding bolt etc and similar work conforming to Fe 410-0 or Fe310-0 work including welded fabricks frames, gate and framed truss, complete all as specified and directed.

M&L formwork to sides of concrete foundation, footing, bases of colums, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar work, in rough finished flat surface of concrete, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for mild steel TMT bars 6 to 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over upto including 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as in stirrups, spacers and binders including binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, type B-1, (nominal mix), (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns and the like, complete all as specified and directed

M&L formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surface of concrete, complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, type B-1, (nominal mix), (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, post, struts and the like, complete all as specified and directed

M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilivers, shelves, including sup-ports, overhangs etc also splays between floors and beam etc, complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, type B-1, ( nominal mix) (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintel over 1.5 mtr span, complete all as specified and directed

M&L formwork to soffits of suspended slabs such as roof slabs, landings and similar work; n exc 200mm thick (Horizontal and sloping) for rough finished surface of concrete, complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, type B-1, ( nominal mix), (using 20mm graded crushed stone aggregate) as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed

M&L for preparation of new steel surface exc 10 cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed by Engr-in-Chagre.

M&L for construction of LLDPE septic tank (conventional) of capacity 10 users designed to carry sewage and sludge water, excavation in any type of soil, brick work in cement mortar 1:4, PCC 1:2:4 type B-2 in foundation, RCC slab cover including RCC precast manhole cover vent shaft, connection etc including returning , filling of soil at sides of tank, well ramming in layers and removing excavated surplus soil to a distance not exc 50m,and shown on drawing No CE/TD 1202/2008 SH 1/2 & 2/2 and as directed at site by Engr-in-Charge.

M&L for construction of soakage well, 1.80 m dia and 3.0 m deep including excavation and earth work in any type of soil, PCC 1:3:6, type C-2 in foundation, walls of honey combed masonry with top ring of M-25 concrete including intercerpting chamber and screen chamber made of brick masonry in cement mortar 1:4, RCC cover slab in M-25, interconnecting pipes of RCC, complete filled with brick bats complete all as specified and shown on drawing No CE/TD 1202/2008 SH 1/2 & 2/2 and as directed at site by Engr-in-Charge.

M&L for construction of soakage well (for 10 user), 1.20 m dia and 4.50 m deep including excavation and earth work in any type of soil, PCC 1:3:6, type C-2 in foundation, walls of honey combed masonry with top ring of M-25 concrete including intercerpting chamber and screen chamber made of brick masonry in cement mortar 1:4, RCC cover slab in M-25, interconnecting pipes of RCC, complete filled with brick bats complete all as specified and shown on drawing No CE/TD 1202/2008 SH 1/2 & 2/2 and as directed at site by Engr-in-Charge.

M&L for plain cement concrete 1:3:6, type-C-2 (using 40mm grade crushed stone aggregated) as in bed to drains pipe including packing under and haunching agsinst the sides of pipe after they are laid and tested for salt glazed stonewere pipe 150mm dia, complete all as specified and directed.

Supply and laying salt glazed stoneware drain pipe grade 'A' 150mm bore laid on concrete bed in floor and jointed, complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B-1 using 20mm graded stone aggregate as in manhole cover, chullah hoods, chajjas, water troughs, mangers, shelves and similar items with plain faces in cement concrete and setting in cement morter 1:4 including necessary formwork complete all as specified and directed

M&L for chequered cement concrete tiles of size 30 cm x 30cm x 25 mm thick set, jointed in neat cement slurry in floor and pointed in white or coloured cement to match the shade of tiles laid over and including 20 mm thick screed bed in cement mortar 1:4, complete all as specified and as directed.

M&L for plain cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work, complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated etc) sheet, any gauge, thickness in roof covering complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nanital or similar pattern roof covering complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed or framed work complete all as specified and directed.

Dismantling structural steel work including welded fabriks frames, doors, gates, grills grating and framed truss etc, complete all as specified and directed.

S&F for rolled mild steel (structural steel) work in roof truss (framed), trussed, purlin, crane gantries, rai;l and fastening and heavy bracket framing (Beam, tee, angle channel or flat section ) including distance piece, cleats etc and painted with one shop coat of zinc chrome primer before hoisting and fixing in position (conforming to Fe-410-W, Gde E-250 quality 'A', complete all as specified and directed.

M&L for Mild steel structural steel work including tubular member as in main and cross beam/columns, hip and jack, rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates (Fe-290 Gde E-165 Quality A) complete all as specified and directed. (Note :- All structural steel work shall be painted with one shop coat of zinc chromate red oxide primer including preparation of surfaces before fabrication and rate shall be included in this item).

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness below or above the ground level, complete all as specified and directed.

M & L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc, complete all as specified and directed.

M & L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25litres per linear meter including drilling and plugging holes in apron etc, complete all as specified and directed.

M & L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

All as per srl item no. 93 here-in-before but except stone. Note: Old stone obtained from demolition will be used.

M&L for 18-20mm thick Machine cut kota stone slab (mirror polished) as in flooring, jointed with grey cement slurry mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including screed bed or bedding layer of 20 mm thick in cement mortar 1:3 of any size including taking down old unserviceable tiles, complete all as specified and directed.

M&L for 18-20mm thick Machine cut kota stone slab (mirror polished) as in riser, steps, skirting, dado, window cill and pillar and jointed with grey cement slurry mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including screed bed or bedding layer of 10 mm thick in cement mortar 1:4 of any size including taking down old unserviceable tiles, complete all as specified and directed.

Taking down cement plaster, any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on stone masonry surface or other than fair faces of brick work/ stone wall surface, finished surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on stone masonry surface or fair faces of brick work/ stone wall surface, finished surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of exterior emulsion weather proof paint of apex ultima over and including a coat of primer over a coat of putty 1.5mm thick, complete all as specified and directed.

Complete removal of existing treatment of old plastered surface of walls and preparing surface including washing rubbing down and stopping of walls and applying two coat of distemper oil emulsion over a coat of alkali resistant primer ove a coat of wall care putty 1.5mm thick, complete all as specified and directed.

Complete removal of existing treatment of old plastered surface of walls/roof surface including cornice and chajjas etc and applying two coats of exterior emulsion weather proof paint of over and including one coat of primer, complete all as specified and directed by Engr-in-Charge.

S&F in repair for stainless steel curtain rod of 20mm dia, complete all as specified and directed.

S&F bracket and finials of stainless steel of 'T' and 'L' type (colour and design approved by GE) for curtain rod stainless steel 20mm dia including fixing to walls with MS full screws (including fixing of wooden pieces of required size of walls) complete as in repair all as specified and directed .

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, complete all as specified and directed.

S&F for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

S&F for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed.

S&F for factory made 2nd class hard wood 35 mm thick plain framed panelled shutters (any No of panels) with panels of timber flat on both sides (feather edges) or of veneered particles board medium density wood particle board with commercial face veneers, fixed to chowkat, complete all as specified and directed.

S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.

S& F for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks, or galvinsed wire staples , complete all as specified and directed.

S&F for pressed steel door frame of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats in PCC 1:3:6 type C-1 using 20mm graded stone agregate complete all as specified and directed.

M&L for 300mm long (lenth of bolt) aluminium alloy, anodised, sliding door bolt with hasp, stapl (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolt of extruced sections or cast aluminium alloy anodised (ISI marked) complete all as specified and directed.

S&F for 6mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug or hanged with existing truss members. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturctions including dismantling of existing ceiling board etc, complete all as specified and directed.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface including dismantling of existing ceiling board etc, complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old steel surface exc 10 cm width or girth and applying one coats of synthetic enamel paint, complete all as specified and as directed by Engr-in-Chagre.

M&L for preparation of old wooden surface exc 10 cm width or girth and applying one coats of synthetic enamel paint, complete all as specified and as directed by Engr-in-Chagre.

M&L for preparation of new plastered surfaces of walls and applying two coats of emulsion plastic paint colour mixed by machine to achieve the required colour (Ivory white) over and including 3mm thick wall care putty, complete all as specified and directed.

M&L complete removal of existing treatment and applying two coats of emulsion plastic paint colour mixed by machine to achieve the required colour (marble finish) over and including 3mm thick wall care putty, complete all as specified and directed.

S&F factory made 1st class hard wood 40mm thick plain framed paneled shutters (any numbers of panels) with pane is of sqm timber flat on both sides (feather edged) or of veneered particles board medium density wood particle boards with commercial face veneers, complete all as specified and directed.

M&L for vitrified tiles light shade (premium quality) 9-10 mm thick (square/ rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar 1:4 including dismantling old unserviceable tiles, complete all as specified and directed.

M&L for wooden tiles 10 mm thick (square/ rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar 1:4 including dismantling old unserviceable tiles, complete all as specified and directed.

S&F for 15 mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc including taking down old tubing, complete all as specified and directed.

S&F in repair for 15mm bore bib tap, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair for PVC connection 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

S & F in repair for brass chromium plated tubular towel rail 20mm dia 600mm long with and including one pair of brass chromium plated bracket complete all as specifed and directed.

S & F in repair for PVC waste pipe 32/40 mm bore fixed to PTMT waste coupling for kitchen sink, complete all as specifed and directed.

M&L in repair for 15mm bore angle valve, fancy type, chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed down high pressure, screwed for iron pipe or for unions and fixed, complete all as specified and directed.

S&F in repair for centre hole basin mixer with popup waste system with 450mm with all connecting accessories, complete all as specified and directed.

S&F in repair for sheet glass shelf assembly consisting 5.5 mm thick, sheet glass shelf 12cm wide with chromium plated bracket guard and rainling 60cm long, complete all as specified and directed.

S&F in repair for glass corner shelf with tempered glass, stainless steel brackets and polished chrome finish rail, complete all as specified and directed by Engr-in-Charge.

S&F in repairs door closer hydraulically regulated, aluminium (extruded section body) designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg (ISI Marked), Complete all as specified and directed.

S&F in repair for vitreous China urinal, full stall type, waterless, premium quality, white, including flush pipe and waste pipe with grating and union for discharge pipe (excluding flushing cistern) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement, complete all as specified and directed.

S&F in repair for vitreous china soap tray embedded in the wall, complete all as specified and directed

S & F in repair 15mm CP brass Health faucet with 1.2 meter long stainless steel hose and wall hook complete all as specified and directed by Engr-in-Charge.

S & F in repair toilet paper holder with flap, complete all as specified and directed by Engr-in-Charge.

S & F in repair Glass shelf 600mm long, complete all as specified and directed by Engr-in-Charge.

S&F in repair for CP brass shower rose of size 125mm with swivel joints fixing to steel pipes etc, complete as in repair all as specified and directed.

M&L for 20mm thick granite black or any other colour, of any type of work (table rubbed and polished) as in steps, jambs, pillars, window - cills, cooking platforms, urinal partition and like set in cement mortar 1:4 including pointed in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including grinding and polishing, complete all as specified and directed.

S&F for solid PVC wall lining consisting of 5mm thick coloured PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification complete after dismantling of old unserviceable PVC lining, complete all as specified and directed

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete after dismantling of old unserviceable PVC lining, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and including dismantling old tank complete all as specifed and directed.

M&L for 25mm bore gun metal, gate / globe valve with iron wheel head screwed on both sides for iron pipes and fixed, complete all as specified and directed.

Complete removal of existing water proofing treatment over RCC roof, projections of any thickness, non approachable/ non accessible, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with wire brush including removing debris from the site and depositing in low lying area where directed and providing following :- (a) Rendering 10mm thick in cement mortar 1:4 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound @ 2% by weight of cement. (b) Apply a coat of bituminous primer confirming to IS-3384@ 0.4 ltr/Sqm on newly plastered surface after curing as per IS-456 and dried. (c) After the primed surface has dried, apply a coat of hot blown bitumen(85/25 penetration) confirming to IS-702 @ 1.2 Kg/Sqm of the surface. (d) Provide polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, and laid by torch application method, end overlaps shall not be less than 150mm and side lap 75mm. Polymeric water proofing membrane should be five layered with centre core as 90 micron high molecular high density polyethylene film, min weight 3 Kg per sqm & minimum 3mm thick reinforced with polyster non wove fabric, APP membrane shall laid acorss the slop from lowest line of sloping roof towards ridge. (e) Over the APP membrane, apply a coat of semi hot blown 85/25 penetration grade bitumen confirming to IS-702 @ 1.20 Kg/ sqm and blinded with fine sand in dry condition @ 0.50 Kg / Sqm dusted over the bitumen coat Note : (i) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. (ii) Ponding test shall be conducted for 72 hrs as directed.

S & F for power coated of any colour (Thickness or powder coating not less than 50 micron) aluminium anodized three track sliding window with two or more shutter with 12 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle lock, etc including 65 x 39.5x 1.5 mm section for complete frame and rubber beading and glazing clips etc., including taking down old existing window, complete as specified and directed by Engr-in-Charge. Note:- Cost of glass, wire mesh, rubber beading, glazing clips, neoprin packing, handles, butt hinges, tower bolts etc will be included in the quoted rate.

M&L for Powder coated anodised aluminium frame of any colour (thickness of powder coating not less than 50 micron) for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge.

M & L for Design, Providing, installation and fixing 12 mm thick Toughened Glass for doors/Windows upto 2.10 M with all as per required arrangement & proper machine edge finish in angle & fixed in the flooring side with Aluminium 'U' channel . Glass panels to be formed as per approved modules 12 mm thick clear toughened glass edge polished and accurate designed holes to be installed by means of steel fittings of an approved make, Including Floor spring, Lock, Door Handle both side, all works including labour, wastages, cost of scaffolding, finishing with frosted design film etc. complete all as specified and directed.

Supply and fixing sheet glass ordinary quality 5.5 mm thick type fixed to aluminium doors, windows & cupboard partitions in squares exc 0.5 sqm in each pane

S & F in repair for 20 mm Pre-laminated bord interior grade both sides laminated includind beading/leaping on all edges complete all as specified and directed by engr in charges.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40 mm complete all as specified and directed.

M & L for second class hard-wood in scantiling of frame work, complete all as specified and directed.

M & L in repair for 4mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces fixed with screws to timber frame work in any shap, size and design complete all as specified and directed.

M&L applying two coat of staining and varnish on new wooden surfaces exc 10 cm width or girth, including preparation of surfaces, complete all as specified and directed.

Taking down existing designer wall mounted panneling exc 0.5 sqm after removel readjusting of the same as per requirment & fixing in same position /location, complete all as specified & directed by Engr-in-charge

Taking down existing designer wall mounted panneling exc 0.5 sqm after removel readjusting of the same as per requirment & fixing in same position /location, complete all as specified & directed by Engr-in-charge

Sch 'A' Part-II (E/M works) Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete, including all fittings such as switches, ceiling roses, pendants, regulators sockets etc.) removing material from the site and making good the disturbed surfaces of walls, floor or ceiling etc. to match with existing specifications, complete all as specified and directed.

M&L for point wiring for one light point/fan point controlled by one way switch with 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including PVC casing caping medium grade of 25mm width complete with all acessories including PVC sunk box ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making good the diturbed surfaces compete all as specified and directed. (Note:- Three run of copper conductor of required size and one run of casing capping measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth)

Description all as per Serial item No 160 above but for one 3 pin 5 Amp socket outlet on independent board controlled by one 6 amp switch, complete all as specified and directed.

Description all as per Serial item No 160 above but for one 3 pin 5 Amp socket outlet on same board controlled by one 6 amp switch, complete all as specified and directed.

Description all as per Serial item No 160 above but for one 5 pin 15 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistraind copper cable with 2.5 sqmm single core multistraind FRLS copper cable as earthling lead complete all as specified and directed.

M&L for modular point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through PVC casing, caping (minimum 25mm in width), with fittings such as tee, corners, overlapping, connectors, etc fixed over walls, ceiling, floors etc including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty and fabricated branded modular metal flush boxes with modular white cover plate and frame concealed in walls with suitable modular fitting housing switches, socket outlet and fan regulators etc, complete all as specified and directed. (Note:- Three run of copper conductor of required size and and colour coding of wiring to be followed as red/yellow/blue for phase, black of neutral and green for earth)

Description all as per srl item No. 164 above but for socket outlet 3 pin 6 Amps on independent board controlled by one 6 amp switch, complete all as specified and directed.

Description all as per Serial item No 164 above but for one 3 pin 15/16 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistraind copper conductor cable with 2.5 sqmm single core multistraind FRLS copper cable as earthing lead, complete all as specified and directed.

M&L for switch piano, flush type single pole, one way 5 Amp, 240 volts complete all as specified and directed.

M&L for switch socket combination 2 in 1, flush type single pole, one way 3 Pin 5 Amp, 240 volts, complete all as specified and directed.

M&L for switch socket combination 2 in 1, flush type single pole, one way, 2 in 1, 5 Pin 15 Amp, 240 volts, complete all as specified and directed.

M&L for socket outlet 2 in 1, flush type, 5 Pin, 5 Amp, 240 volts, complete all as specified and directed.

M&L for socket outlet 2 in 1, flush type, 6 Pin 5 & 15 Amp, 240 volts, complete all as specified and directed.

S&F for ceiling rose 3 terminal/ PVC / polycarbonate isolated body surface bakelite , 63.5 x 17mm complete all as specified and directed.

M&L for ceiling fan regulator elctronic, flush type, hum free suitable to control speed of fan from 0 to 100% rotary type five step 240 volts AC complete all as specified and directed.

S&F for modular switch 6 Amps, one way, one module complete all as specified and directed.

S&F for modular socket outlet 6 Amps, 2/3 pin combination, 2 module complete all as specified and directed.

S&F for modular switch 16 Amps, one way, one module complete all as specified and directed.

S&F for modular socket outlet 6/16 Amps, 6 pin combination, 2 module complete all as specified and directed.

S&F for modular stepped type fan regulator electronic, 100 watt, 2 module, complete all as specified and directed.

S&F modular white cover plate with frame 3 module, complete all as specified and directed.

S&F modular white cover plate with frame 6 module, complete all as specified and directed.

S&F modular white cover plate with frame 8 module, complete all as specified and directed.

S&F in replacement for lamp holder insulated body PVC/ Polycarbonate type with back plate suitable for batten/angular/pendent fittings including LED lamp 9 watt complete all as specified and directed.

M&L in repair for LED Tube light fitting, complete with 1x 20 watts, 220V, AC decorative box type with driver, holder in and including LED tube light connection complete prewired and connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and connector block etc and necessary fixing arrangement at any height complete all as specified and directed.

S&F for environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head 10 watt 6000 K inbuilt LED luminaire comprising of high brightness LEDs, IP54 protection including connecting electrically using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed.

S&F in repair for LED recess mounting high lumen panel light 36 watts, 2" x 2" feet with white power coated CRCA housing with high power LEDs, aluminium front frame with flat white high transmission acrylic cover, internally prewired, 230v complete with all accessories such as electronic driver, LED strip, connector block etc and necessary fixing arrangement at any height complete all as specified and directed

S&F in repair for environmental friendly, ultra modern, energy saving, surface mounted, recess mounted round/ square fixture of size 6 inch 12 watt LED 6500 K or as per required at site with opal difuser connecting electrically using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed.

S&F in repair for decorative Bed side light fitting suitable for 3 watt LED lamp, complete all as specified and directed.

S&F in repair for decorative Mirror light fitting suitable for 10 watt LED lamp, complete all as specified and directed.

S&F in repair for decorative wall light stainless steel, rust free fitting with white glass suitable for 9 watt LED lamp, complete all as specified and directed.

S&F in repair for new generation, environmental friendly, ultra modern, energy saving, long life aesthetically designed aluminium landscape luminaire Bollard light 8/10 watt for diffused lighting with high power LEDs as light source and making necessary connection with 2.5 Sqmm PVC insulated copper conductor twin core cable 1100 volts upto 5mtr length, complete all as specified and directed.

S&F in repair for LED gate light fitting 7.5 watt with cast aluminium spigot lid cover and clear cover with IP 65 protection complete with all accessories including fixing arrangement on top surface of boundary wall or on pillar by providing GI pipe of suitable size and length as per site requirement and making good to the disturbed portion to match with existing surface, complete all as specified and directed.

S&F for MCB distribution board SPN 12 way, double door 240 volts duly painted with epoxy based powder coated painting suitable for mounting MCB TP/FP as incomer and outgoings complete with busbar, neutral bar, earth bar connecting cable links with top and bottom removable gand plate with IP 42 protection, complete as in repairs all as specified and directed. (Note:- MCBs will be measured separately.)

S&F for MCB distribution board SPN 8 way, double door 240 volts duly painted with epoxy based powder coated painting suitable for mounting MCB TP/FP as incomer and outgoings complete with busbar, neutral bar, earth bar connecting cable links with top and bottom removable gand plate with IP 42 protection, complete all as specified and directed. (Note:- MCBs will be measured separately.)

M&L for MCB single pole, 240 volts any rating from 6 to 32 amps, 'C' series/curve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M&L for MCB single pole & neutral 240 volts any rating from 32 to 63amps, 'C' series/curve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & RCC cover all as specified & shown in elect plate No. 3 of SSR part I of 2010 including testing on completion, including taking down old earthing complete all as specified. (Note:-Earth strip and protection pipe upto board is included in the rate quoted)

Supply, laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 10 Sqmm 2 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands, complete all as specified and directed.

Supply, laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 16 Sqmm 2 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands, including taking down old cable complete all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of cable shall be one length unless otherwise as directed by GE).

M&L for speading unwashed river sand for cushioning and covering the under ground cables in trenches and punning to provide required cover complete all as specified in SSR part-I and as directed. Note: punned thickness of sand shall be measured.

Supplying and laying sub class 'B' brick old size laid dry flat over the cable abutting eaxh other, length of cable equal to width of brick, complete all as specified and directed.

S&F for exhaust fan of 300mm sweep, heavy duty, 1200 RPM electrical operated 230 Volts AC single phase, steel body with all accessories and louver etc, complete all as specified and directed.

S&F in repair for exhaust fan of 300mm sweep, heavy duty, 1200 RPM electrical operated 230 Volts AC single phase, made of sturdy engineering plastic with all accessories and louver etc, complete all as specified and directed.

S&F in repair for air circulators fan of 450mm sweep, electrical operated 230 Volts AC single phase,suitable for wall mounting, complete all as specified and directed.

M&L for sub main wiring complete with 2 run of 6 sqmm, single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded duly colour coded cable drawn through and including PVC conduit of size 25mm width or above as required at site and accessories such as tee, corners,overlaping connector etc of suitable size fixed on surface of walls/roofs/ceiling and including 01 run of 6 sqmm single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly including removing old unserviceable sub main wiring items complete all as specified and directed. (Note : - 02 run of 6 sqmm single core copper conductor cable and 01 run of 6 sqmm single core copper conductor and 01 run of PVC conduit shall be measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth).

M&L for sub main wiring complete with 2 run of 4 sqmm, single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded duly colour coded cable drawn through and including PVC conduit of size 25mm width or above as required at site and accessories such as tee, corners,overlaping connector etc of suitable size fixed on surface of walls/roofs/ceiling and including 01 run of 4 sqmm single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly including removing old unserviceable sub main wiring items complete all as specified and directed. (Note : - 02 run of 4 sqmm single core copper conductor cable and 01 run of 4 sqmm single core copper conductor and 01 run of PVC conduit shall be measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth).

M&L for cutting, threading and inserting tee for taking new branch connection from existing pipeline of size 25mm bore complete all as specified and directed

S&F of storage water heater (geyser) 5 star rated as per BEE norms electrically oprated suitable for 230 volts, 50 Hz, AC supply system complete with porcelain /glass coated insulated heating element copper tank of 2 KW capacity 25 litre, commplee with all accessories such as safety valve, thermostate, NRV etc, complete all as specified and directed.

SATVIR GUPTA ENGINEER and CONTRACTOR (BID ID -3098145)

J. PRO BUILDERS (BID ID -3103637)

M/s Anil Engineers & Builders (BID ID -3110745)