8165/GE/SMB/T-70/2025-26 SPL REPAIRS TO BLDG NO P 20 OR MD ACCN AT KHETARPAL LINES AND BLDG NO T 24 25A AND T 24 25A1 COOK HOUSE AND DINING HALL AT MH SAMBA AND PROVN OF 03 GARBAGE DISPOSAL POINTS AT JCOs OR MD ACCN AT KOHIMA LINES AT MIL STN SAMBA

Amount

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified. Note :- Work will be carried out upto 2nd storey of bldgs also as per pirection of Engr-in-charge including necessary formwok and scaffolding required as per site conditions & no extra payment shall be made on this account.

Rendering 10+5 mm thick on fair faces of brick or concrete surface walls in two layers, in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement (up to 2nd storey with necessary scaffolding) complete all as specified and as directed by Engineer-in-charge.

M&L Rendering cement plaster, 10 mm thick on fair faces of brick/concrete surfaces of wall in cement mortar 1:6 finished even and smooth w/o using extra cement complete all as specified.

Rendering 5 mm thick on fair faces of brick or concrete surface ceilings, in cement mortar 1:3 , rendering is to be finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) ground floor to second floors and pavings n exc 15 cm thickness (below or above ground level ) and removing the rubbish from the work site out side defence premises complete all as specified.

Rendering 15mm thck in CM 1:3 or Plain Cement Concrete as in sunken floors without extra cement on walls/floors and including mixing of water proofing compound (WPC shall be measured and paid separately)

Cleaning of dust removal to all loose existing sunken floor any material manually and with heat tark gun to get smooth plain finished surface including removing of vegetation/plantation with no loose material on surface. Repair all joints and cracks with highly elastic bituminous cold applied putty of tarplasic having penetration after setting upto 8mm. Levelling of surface to give proper slope will be done as per site requirements with Shalipatch or euqivalent make of approved by GE cold applied.Bituminous mortar and cold emulsion cum water proofing liquid of Shalikote-T-10 or equavalent make as approved by GE, created SSD condition on surface with water. Prime the surface with Tarfelt LM or equivalent make as approved by GE mixed with portable water in the ratio of 1:1 and apply @ 400gm per Sqm (as per surface condition). Apply first coat of Tarfelt LM or equivalent make as approved by GE having alongwith 200% conforming to ASTM-C-412 & having crack bridging of 8mm conforming to ASTM-C-836 with tensile strength after 7 days 0.50mm conforming to ASTM-C-412 with no diluation water on primed surface while the surface is still tacky with consumption of 700gm /Sqm. Apply 2nd coat on cured first coat with consumption @ 700gm/Sqm in opposite direction of 1st coat by brush or roller. Allow it to dry for 10-12 hrs after apply 3rd coat with consumption @ 700gm/Sqm. Ensure final curing time of 36 hrs before allowing/carrying out any further work. Conduct ponding test after minimum 7 days applying 2 coats of U V Resistand Elastomeric Exterior Axcrylic weather resistant water proof coating of Shalicryl - 215 or eauivalent make as approved by GE having elongation of 300% after curing of 14 days conforming to ASTM D-6083, for U V protection of bituminous Elastomeric Acrylic emulsified liquid membrance of Tarfelt LM or equivalent make as approved by GE to give long life and prevent its deterioration from sunlight. Note : Application of water proofing treatment will be done by authorised applicator only.

M&L Cement concrete type E-2, 1:5:10 ( 40 mm graded agregate) in Sunkan filling and mass concrete complete all as specified and directed by Emgr-in-charge.

M&L 40 mm dia G I tubing heavy grade galvanised laid over floors as a spout pipe in sunken floors all as specified.

Supply only Water proofing compound liquid.

M&L for repairing of concrete surfaces such as balcony, chajjas, upward or downward facias ,column, pillar, ceiling and similar items with plain cement concrete 1:2:4 type B-0 including minimum reinforcement or rendering 10-15mm thick as per site requirement in CM 1:3 without using extra cement finished even and fair complete all as specified and directed (Up to second storey bldgs and including necessory formwork and scaffolding and provision of minimum reinforcement required as per site condition also taking down or dismantling as required at site).

Demolition of reinforced cement concrete of any discription ground to 2nd floors and removing the rubbish from the work site out side defence premises complete all as specified.

M&L for RCC M-15, nominal mix, type B-1(1:2:4), using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified and directed.

M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed

Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster/demolition of cement concrete any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L Rendering 15mm thck in CM 1:4 on Concrete surfaces of roof finished fair & even and including mixing of water proofing compound (WPC shall be measured and paid separately)

M&L for water proofing treatment in the following sequences:- (a) Applying 1st course of bituminous primer conforming to IS -3384 @ 0.4 Kg/Sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely (bi) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (C) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed .

M&L for preparation of newly sufrace of APP Membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm etc

Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by Engineer-in-charge.

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material from the work site ouside defence premises complete all as specified.

Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge

Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified and as directed by Engineer-in-charge

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

Material and labour for Providing, cement concrete 1:2:4 type B-1 (using 20mm graded aggregate ), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Dismantling water tanks and removing to store of water storage tanks (Cap. 250 ltr to 500 ltr ) complete all as specified and directed by Engineer-in-charge.

Supply and fixing Rotational moulded polyethylene water storage tanks of 500 litres capacity,(cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified

Disconnecting of water tank of 500 ltr capacity setting aside (or lowering if required) for repairs, cleaning etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing,etc. measured separately).

Cleaning and removing all scale and dirt etc, from exc 250 & n exc 500 litres capacity tanks in any position and from mouths of circulating pipes etc, and disinfection completely by making all the arrangements and writing date of cleaning on side of tanks also containing completion from user complete all as directed.

Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 15 mm bore pipe, including making connections complete all as specified and fixed.

Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and fixed.

Supply and fixing in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore pipe including making connections complete all as as specified and fixed (Minimum weight 20mm-210 gms).

S&F in repair PVC tank covers required for 500 ltr to 1000 ltr PVC water tanks complete all as specified and fixed

Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

Taking up or down steel tubing of 25 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

Supply and fixing tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge

Supply and fixing tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing tubes 'medium grade' galvanised, 25 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

M&L cutting chases, pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings,steps,cills,sunshades,shelves,lintels etc,and cutting chases for concealed water tubing or concealed conduit wiring,etc,and making good,cutting n.exc 10cm girth in brick walls.

Repair to existing PVC pipe/CI pipe including making the joints water tight by using suitable material including cleaning if required and refixing of any dia. Note : Work to be carried out up to 2nd storey bldg in any condition of working place/area

Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specied and directed.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4.

Material and labour glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified.

Material and labour Ceramic light shade tiles 10 mm thick (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match over and including 15 mm thick screed bed in CM 1:4.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

S&F pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors single rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified. Make:- Shivam Steel, Jammu

S&F pressed steel frames of size 105mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified.

S&F Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. (both side lamination) Note :- Sampel approved by Engr-in-Charge or GE.

Supply and fixing Factory made, plain framed, panelled shutter (two Panel) 35mm thick, 2nd class Hardwood with lock rail and panel of 9 mm B.W.P commercial ply. The size of rail and stiles as per as per IS:1003 (Part-I),kiln seasoned and chemically pressure treated complete all as directed by Engr-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly.The quoted rate is included for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, complete all as specified and directed.(Sample approved by GE)

Supply and fixing 35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars,stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed by Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge.

Repair/ easing of wooden door any type, glazed or panelled, by trimming the side of door shutter where rubbing with chowkhat, unscrew the hinges screws and lift the door and fix with screws, tightening of wire mesh etc all as per Engr-In-Charge.

Pressed steel cup board/kitchen frame of MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately.

Prelaminated MDF board 19 mm thick as in shutters/shelves (exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame worknincluding lipping (15 mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all as specified and as directed by Engr-in-Charge.

Dismantling Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar

M&L 16 to 18 mm thick green udaipur marble in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 as directed by Engr-in-charge.

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

Supply and fixing in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified fixed with stainless steel wire staples.

S&F butt hinges of mild steel cold rolled medium weight of size 100mm as specified.

S&F Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

S&F Aluminium handles, fabricated type, anodised Size-100mm, anodised section and fixed complete all as specified. (ISI Marked)

S&F Aluminium alloy, anodised, sliding door bolt Size- 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F aluminium hanging floor door stopper,Twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified. ( ISI Marked)

S&F in repair aluminium bottom door seal with brushes, length 1.2 mtr, fix with screw, suitable for wooden door complete all as specified.

Supply and fixing in repair mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC (SWR) , bends for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC (SWR) , bends with access door for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR) , bends for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

S&F UPVC (SWR) , reducers 110 mm dia complete all as specified.

S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified.

Supply and fixing in repair UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair, UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

S&F in repair Sink Cock with swinging casted spout (Wall Mounted model) with wall flange complete all as specified.

S&F in repair 15 mm bore Bib Cock with wall flange cast copper alloy, chromium plated fancy type ,complete all as specified.

S&F in repair 15mm bore angle valve with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified.

S&F in repair 15mm bore CP Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

S&F in repair Chromium plated, towel ring , complete all as specified.

S&F in repair Corner Glass Shelf (with Bracket) as per directed by Engr-in-charge.

S&F in repair PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.

S&F in repair Brass chromium plated shower rose with or without swivel joints, 125mm size, including fixing to steel pipe or union.

S&F in repair Vitreous China, wash basin white, flat back , size 400mmx300 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass. complete all as specified and as directed by Engineer-in-charge.

S&F in repair PVC valveless,syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge.

S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including L bend, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition)

Supply and fixing in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom,complete all as directed. .

S&F 15mm bore CP jet spray for Padestal pattern WC all complete and as directed.

Supply and fixing in repair sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 610mm x 460mm bowl size 560mm x 410mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified and directed.

S & F Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (30"x36"x10") fixed with steel fastners or steel screw complete.

S&F in repair stainless steel lock grating plain/hole size 100 mm dia including embeding in tiles with white cement.

Preparation of new plastered or unplastered surfaces of ceilings to achieve smooth and even surface and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge.

Material ad labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over a coat of wall care putty of 3 mm thick and one coat of primer complete all as specified.

Preparation of new plastered/ concrete surfaces of walls to achieve smooth and even surface and applying two coats of cement based paint over and including one coat of primer (up to 2nd storey with necessary/scaffolding) complete all as specified and asdirected by Engr-in-charge.

Preparation of old decorated brick /concrete, plastered /un-plastered surfaces of ceilings, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots , rubbing with sand paper and applying one coat of white wash on ceiling, complete all as specified and directed.

Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying one coat of oil bound distemper on walls, pillars,cornices surface including making good uneven surface/holes with birla wall care putty coloured in same shade where ever required etc. complete all as specified and directed.

Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying one coat of cement base paint on walls, pillars, cornice etc (upto 2nd storey with necessary scaffolding complete all as specified and directed.

Preparation of new painted wooden surfaces having width/girth exceeding 10 cm including necessry putty filling with knife of same colour where required to achieve smooth and even surface and applying two coat of synthetic enamel paint on wood surfaces of any description over a coat of pink primer ( up to 2nd storey with necessary scaffolding) complete all as specified and directed

Preparation of old painted wooden surfaces having width/girth exceeding 10 cm including necessry putty filling with knife of same colour where required to achieve smooth and even surface and applying one coat of synthetic enamel paint on wood surfaces of any description ( up to 2nd storey with necessary scaffolding) complete all as specified and directed

Preparation of new painted steel surfaces having width/girth exceeding 10 cm including necessry rubbing with sand paper or grinding by hand grinder to achieve smooth and even surface and applying two coat of synthetic enamel paint on steel surfaces over a coat of red oxide primer ( up to 2nd storey with necessary scaffolding) complete all as specified and directed

Preparation of old painted steel surfaces having width/girth exceeding 10 cm including necessry rubbing with sand paper or grinding by hand grinder to achieve smooth and even surface and applying one coat of synthetic enamel paint on steel surfaces of any description ( up to 2nd storey with necessary scaffolding) complete all as specified and directed

Writing letters or figures (Block, Roman. Italic or Indian) n.exc 30cm high including obliterating old writing of any description n.exc 0.2 Sqm with paint to match existing work complete all as specified Such as NP-02,P-101,T-104

M&L for 50mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

Material & labour factory made steel windows/VENTILATOR double shutter box type, outer frame made out of ERW TUBE 'P' section (60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (ii) PCC block for embedding lugs.

Hacking out old broken glass (any thickness,size quality or description) from any types of wooden/steel/alum (up to 4th storey) frames or stone concrete or brick surrounds glazed with putty or fixed with beads.

S & F 3.5 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

S&F 3.5 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Repairs to steel window, ventilators of any size to make it functional (including slot pin, hinge, hook and eye of standard quality where required), resecuring of windows wire gauge and railings/grills by using welding equipments, complete all as directed.

M & L for Machine cut kota stone slab flooring 18-20mm thick over 1:4 cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete

Systamatically cleaning and de-silting-sludge of blocked sewage pipe line 100 to 300 mm dia and any depth including taking out sludge/silt and other foreign materials from sewage line by rodding with using steel rod or split bamboo sticks thoroughly from both sides between adjacent manholes still clear flow of sewage line is observed passing knots kamti and disc of required size or pumping out liquid waste / sewage plugging and diverting the flow to the drain if necessary and stacking the removed silt / sludge in deposits out side defence land as directed including taking precautionally measures such as safety belts dry cell for lighting inside the manholes and drain etc. sprinking bleaching powder on the silt/sludge to removed to avoid bad smell and disposal of sludge, complete all as specified and directed. Note- Rate deemed to be inclusive of excavation of earth pits and bleaching powder if required for disposal of sludge)

Dismantling, asbestos cement, corrugated or semi-corrugated sheets in roofs incl ridge, complete all as specified.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, framed work, complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

S&F Roof trusses (framed), trussed, purlins, rafters, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, flat, hollow sections) including distance pieces, cleats, welding/rivets/nut/bolts/washer etc, complete all as specified.

S & F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an coulour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as specified.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strenth of 550 Mpa as in roof covering/ridge fixed with self tapping screws as specified.

Providing and fixing of V-board-"Visaka"/E-board 'Everest' make 600x600x4mm thick white prelaminated seif embosed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24 mm wide T-section exposed flanges which shall be power coated white. The frame work shall comprise of main runner made from 0.33mm thick G S sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers/suspended with 2 run of 2 mm dia of GI wire to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600 mm to be supported independently. 600x600 mm modulesto be formed by fitting 600 mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS shgeet of size 19x19mm and 300 mm long of white colour all as specified by manufacture instruction.

M&L Aluminum Power coated, sliding windows three track with mosquito proofing with style 44.4x44.5x2mm thick including 4 mm thick coloured/tinted/frosted glass panes including all necessary fittings and fixtures complete.

Anodised aluminium grills, 6mm dia size 100x100mm fixed to aluminium windows and thickness of powder coating not less than 50 micron, complete all as specified.

Supply and fixing Galvanised mild steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with galvanised mild steel wire staple

Supply and fixing for stainless steel medium weight Butt hinges, 100mm , complete all as specified and as directed

M&L for 50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed.

S&F in repair aluminium bottom door seal with brushes, length 1.2 mtr, fix with screw, suitable for wooden door complete all as specified.

S&F in repair aluminium extruded section body, door closer hydraulically regulated, designation No. 1, universal type, suitable for door shutters of 800 mm in width and of weight not more than 35kg and fixed.

S&F in repair Brass Mortice lock with brass handles and fittings , 4 lever vertical type, size 100 mm including complete accessories complete all as specified.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

S&F sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 355mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge.

Pressed steel cup board frame of MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately.

Surface dressing in soft/loose soil n.exc 15 cm in deep and getting out.

Excavation in trenches ,n exc 1.5 wide in depth for foundation and getting out in soft loose soil, complete all as specified

M&L Cement concrete type D2 1:4:8 (40 mm graded aggregate) as in foundation filling and mass concrete all as specified.

M&L of brick work with sub class B brunt old size bricks straight or curved on plan exc 6m mean radius blunt in CM 1:6 all as specified.

M&L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick, in Hard dense soil complete, all as specified.

M&L Removal of excavated soil to a distance not exc 50 metre depositing where directed at a level not exceeding 1.50 metre above the starting point.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, including fixing in PCC plateform/Brick wall.

M&L for 75 mm thick Cement concrete type D-2, 1:4:8 (40mm graded agg) as in, sub base/sub floor/floor & paving etc all as specified.

M&L for preparation of new or previously untreated surface of steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified.

S&F Wire netting of galvanised steel wire 1.40 mm dia size of mesh 25 mm fixed with tinned tacks of wire staples.

M&L Cement concrete 75 mm thick 1:3:6 type C-2 using 40 mm graded stone aggregate complete all as specified.

M&L 50 mm thick sand filling under floor or in foundation incl watering and consolidation complete all as specified.

M&L Machine pressed precast concrete interlocking paver block rubber moulded glossy finish any shape, any colour and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade incl filling interstices with sand complete all as specified.

M&L cement concrete 1:2:4 type B-0 using 12.5 mm graded stone agg as in kerb stone/coping plinth course and the like incl weathering slightly rounded or chamfered angle and throating as directed.

Material and labour for Non-skid Ceramic joint less coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4

Taking down carefully copper/aluminium point wiring (light, fan, light & power socket) complete with fittings and fixtures such as switches,ceiling rose ,pendents ,regulators,socket,lampholders brackets,bulk head fitting,tube lights etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and also making good distrubed surfaces of wall,floors etc all as specified and directed by Engr In Charge

M&L for point wiring using FRLS PVC insulated unsheathed /multistranded copper conductor cable 1.5 sq mm drawn through and including pvc conduit marked and of appropriate size as specified, fixed in conceeled of wall/ceiling with mild steel sunken box and bakelite sheet 3 mm thick including all fittings such as tees, bend and junction boxes etc complete for following:- Make of Cable :-Havells/Polycab or equivalent Make of Conduit:-As per IS

a) One light/Fan point controlled by one switch 5 Amps one way using cable (1.5 Sq mm for phase and neutral and 1.5 sq mm earthing)

b)All as per srl item No 2 above but for call bell point complete all as specified and directed.

c) One 5 Amp socket outlet on independent board.

d) One 5 Amp socket outlet on same board.

All as per Item Srl No160 above but for one socket outlet 15 Amps on Independent board using cable (2.5 Sq mm for Phase & neutral and 2.5 Sq mm for earthing).

S&F Sheet metal enclosure factory made (double door) shutter type for DB SPN, 240 Volts, 8 ways with 200 Amps rated bus bar, neutral link, earth bar complete.

S&F in replacement SPN 40 to 63 Amp, type 'C'10KA, 240 Volts.

S&F in replacement MCB SP 5 to 32 Amp, 'C'10KA, 240 Volts.

S&F Switch piano, flush type 5 Amp, One Way.

Supply and fix bell push flush type with indicator 6 Amps complete all as specified and directed,.

S&F socket outlet 2-in-1, 3 pin 5 Amp.

S&F Switch piano, flush type 15 Amp, .

S&F socket out let 2 in 1, 5 & 15 Amp flush type.

S&F ceiling rose 3 terminal size 50*65 mm surface type.

S&F Electronic fan regulator flush mounting step type 300-400 watts complete.

Supply and fixing electronic bell ding-dong AC 230 Volts single pole complete all as specified and diercted.

S&F LED Lights fitting 1x18 watt,220V, AC Decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S & Replacement for angular type Lamp holder PVC policarbonate type with back plate including Lamp 7Watt complete all as specified '

Earthing complete with galvanised earth plate electrode 60 cmx 60 cmx 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of the plate not less than 1.5M belownormal GL connected to GI wire 4mm as earthing lead by means of nut,bolts and check nut and washer,GI light grade protection pipe 15 mm dia. upto 7.5 m,GI watering pipe 20 mm dia,RCC cover with funnel,excavation in any type of soil,PCC pit charcoal ,salt all as shown in electrical plate No 5 of SSR Part I, including earth test point up to pannel board,all as specified or indicated including testing on completion.

S & F of sheet metal enclosures distribution boards, double door ,VTPN, 415 volts 4 ways (one incoming three phase & twelve out goings single phase )for MCCB & MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following a) MCCB FOUR POLE 100 AMPS AC 415 VOLTS 16 KA=01 NO (for incoming ) (b) MCB SP 63 amps = 04 Nos (for outgoings) . ( Note :- (i)The DB shall be VTPN series. (ii) The DB shall be flush fixed and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped.(iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly. (vi) cutting chasing shall be part of job at no extra cost .

S& F LED Street light fitting 35 watt 230 v AC out door type with high pressure die complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65/66 protection complete.

M & L for submain wiring with copper conductor PVC insulated FRLS of size 2 x 10 sqmm alongwith earth wire of size 1 x 10sqmm on wall surface with and including PVC casing caping of suitable size complete all as specified and as directed by Engr in Charge.

Supply and fixing including Taking out and removing old unserviceable XPLE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm 3.5 core in trenches,through pipe,under culvert or in air complete all as directed including using existing Cable cushioning and cable protection complete as directed.

Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for foundation of pole and laying of UG cable and getting out in any type of soil complete all as specified and directed.

Returning filling in, including spreading, watering and well ramming in layers not exceeding 25 cm thick in any type soil complete all as spd and directed.

Removing excavated material (soil) to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as spd and directed.

Sand cushioning to under ground cable using fine sand (8 cm before & 15 cm after laying of cable) complete all as specified.

Material and labour for sub class B brick old size covering laid dry ,flat transversely along the length of cable on sand cushioning with width eqal to the length of the brick complete.

Supply, fixing & laying GI pipe light grade 50mm bore in trench, under floor, wall and on pole for cable protection.

S&F amp rating 240V, 10KA 'C'curve miniature circuit breaker (MCB) of SPN 32amp poles current carrying capacity in the MCB DB complete with connection testing and commissioning

S&F Socket outlet 2-in-1, 3 pin 15 Amp.

S&F recess mounted LED fitting 36 W of size 600mmx600mm with diffuser pre wired LED Panel and inbuilt LED driver suitable for 36W 240V 50Hz fix on false ceiling and necessary clip as specified and directed by Engineer-in-charge

Taking down the unservicable /brunt sub main wiring from wooden batten and M & L for submain wiring in and including PVC conduit 1.8 mm thick ,20 mm dia with two run of PVC insulated, unsheathed multistranded copper conductor of 10sqmm(FRLS) and one run of PVC insulated,unsheathed multistranded copper conductor 10 sqmm (green in colour) for earth continuity conductor and connected to common earth dolly with thimble etc, complete all as specified and directed. (Two run of 10 sqmm plus one run 10 sqmm of earth wire will be measured as 1RM) Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green)(Make of 10 sqmm copper wire: Havells or technocommerically equivalant make of Grandlay/Finolex.

S&F 415 V 10KA 'B' curve miniature circuit breaker (MCB) of TPN/FP 63Amp poles and current carrying capacity in the DB complete with connection testing and commissioning.

S&F Sheet metal enclosure factory made (Single door) shutter type for DB , TPN 415 Volts, 4ways with 200 Amps rated bus bar, neutral link, earth bar complete.

Supply, Laying, Testing and commissioning of LT cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminum conductor of size 25 sq mm 4 core complete all as specified and directed

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation of stay assembly and laying of LT/HT cables in soft/lose soil and getting out, complete all as specified.

M & L for Sand cushioning for under ground cable upto 8 cm before laying the cable and 15 cm after laying and stretching the cable complete all as spd and directed. Note : Punned thickness shall be measured & paid )

S&F Single pole and neutral enclosure with a two pin and socket complete with one single pole MCB 20Amp complete all as spd and directed

Note:- The contract sum arrived after deduction of amount of Sch of credit as listed in tender Documents.

s k construction co (BID ID -3465741)

THAKUR BUILDERS AND CO (BID ID -3467099)

M/s Sahib and Company (BID ID -3466921)

J.K & Company (BID ID -3467096)

AAR KAY BEE ENTERPRISES (BID ID -3467104)

PRATHAM TRADERS (BID ID -3466937)

NEW GURBINDER INDUSTRIES (BID ID -3466973)