REPAIR REPLACEMENT OF FLOORING TILING ROOFING CEILING AND OTHER MISC BR WORKS AT BIKRAM ENCLAVE NODE AND AOR OF AGE BR II GE SOUTH UDHAMPUR

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

25 mm thick PCC 1:2:4 type B0 using 12.5mm graded aggregate as in level course on floor etc complete all as specified and as directed.

Non skid coloured tiles (square/rectengular) 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc including 15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified.

All as per item No 3 above but on vertical surfaces as in skirting complete all as specified and as directed

Non skid coloured tiles (square/rectengular) 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, including 15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

Glazed Coloured Ceramic tiles in vertical surface 300x450x7mm thick incl laid over 10 mm thick screed bed in CM 1:4, set and joint in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard and dense soil,complete all as specified and as directed

75 mm thick plain cement concrete type D-2 (1:4:8) (40 mm graded stone aggregates) as in sub base complete all as specified and directed.

Sand cushion 20 to 30mm thick for fixing of inter locking tiles complete all as specified and directed.

Machine pressed precast concrete interlocking paver block (glossy finish)of approved shape and size confirming to IS 15658-2006 of 60 mm thickness with grey cement and no pigment, M-35 Grade of approved colour and design complete all as specified and directed.

Removing excavated soil to a distance exc 50m and n.exc1.50 km out side defence land complete all as specified and as directed.

Dismantling asbestos cement/galvalum sheet/CGI (corrugated , semi corrugated etc) sheets as in roof covering.

0.50 mm thick prepainted galvalume aluminium zinc coated GI based semi corrugated/profile steel sheeting of any colour, having tensile strength of 550MPA as in roof covering, wall cladding with self tapping screws or 'L' type of 'J' type or cranked hook bolts in lieu of screws as per manufactures instructions, complete all as specified and as directed.

0.50 mm thick prepainted galvalume aluminium zinc coated GI based plain steel sheeting of any colour, having tensile strength of 550MPA as in roof covering, wall cladding with self tapping screws or 'L' type of 'J' type or cranked hook bolts in lieu of screws as per manufactures instructions, all as specified and directed.

Rolled section as in main and cross beams, purlins, rafters ,posts where connected to common rafter and running rails,eves board framing work, tank staging work etc conforming to Fe- 410-w complete all as specified. Ref HQ CEUZ as per span of site reqmt, complete all as specified and as directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 10mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric five layred APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.5 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm, complete all as specified and as directed by Engr-in- Charge/ GE.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulaton boards/slabs/blankets, any thickness, including cover fillets,complete all as specified and as directed.

AC designer composite ceiling board 4mm thick in 600mmx600mm panel confirming to IS-14682 type-B category-3 including GI frame work with size of grid 605x605mm for seemless ceiling comprising of GI perimeter , holdfast & suspenders and all accessories complete all as specified and as directed by Engineer-in-charge/ GE.

Granite stone 18-20mm thick (table rubbed and polished) in window cills, cooking plateforms and the like not less than 1 sqm (in one piece0, laid over 15mm thick layer of cement mortar 1:3 after roughning of existing concrete surface and applying a layer of neat cement slurry @ 3kg/sqm including pointing in white cement 1:2 using marble dust with admixture of pigments to match with shade of stone, including demolition of stone slabs and tiles of any description or thickness in floors etc. laid, bedded and pointed in any mortar complete all as specified and as directed.

Vitrified Dura stone tiles 300 x 300 x 10 mm thick as in floors and over & including 15mm thick screed bed or bedding layer in cement mortar 1:4, inckuding jointed with neat cement slurry and pointed in coloured cement to match the surfaces of tiles, complete all as specified and directed.

Machine cut kota stone slab flooring 18-20mm thick over cement screed base 15mm thick in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles complete all as specified and as directed.

PCC type D2(1:4:8) using 40mm graded crushed aggregate as mass conc and filling of foundation, complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified.

Rendering 15mm thick on brick or concrete surfaces of walls in CM (1:4) including finishing the surfaces even and smooth without using extra cement as in manholes, septic tank, filter bed out let drain etc all as directed by Engineer-in-Charge.

Random rubble masonry built in cement mortar 1:6, uncoursed, well bonded, bedded and solidly hearted complete all as specified and as directed.

Flush pointing to stone rubble masonry, uncourse or brought up to courses built in cm 1:4, complete all as specified and as directed.

Providing 40 mm thick cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in floor and finished even and smooth without using extra cement complete all as specified and as directed.

Providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed.

Cement concrete 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregates as in cills, lintels, upto 1.50 metre clear span, copings, benching, bed plates etc. and in similar works including weathering, slightly rounded or chamfered angles and throating and necessary form works complete all as specified .

Cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in surface channels and drains complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

15 mm thick rendering on fair faces of brick or stone/concrete surfaces in cement mortar 1:4 and finished surface even and smooth without using extra cement complete with water proofing compound complete all as specified and as directed. (WPC shall be measured separtely)

15 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

10 mm thick rendering on fair faces of brick /concrete surfaces as in ceiling in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed.

Applying one coat of oil bond distemper on walls including preparation and complete removal of existing treatment from old decorated plastered or unplastered surfaces of walls, tint and shade as approved by Engr-in-charge, complete all as specified and as directed.

Applying two coat of oil bond distemper on walls after preparation of newly plastered surfaces complete all as specified and as directed.

Applying two coats of white washing on ceiling including preparation of newly plastered surfaces complete all as specified and as directed.

Applying two coats of cement base paint after preparation of newly plastered surfaces complete all as specified and as directed.

Applying one coats of cement base paint after preparation of old plastered surfaces complete all as specified and as directed.

Applying one coat of white wash on old decorated plastered surfaces of ceiling after preparation of surfaces complete all as specified and as directed.

Applying one coat of white wash on old decorated plastered surfaces of walls after preparation of surfaces complete all as specified and as directed.

Applying 1mm thick layer of wall putty on walls to give uniform surface complete all as specified and directed. Note :-(Before applying of wall care putty, Complete removing of treatment as directed and approved by Engr-in-charge)

Preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide, complete all as specified and as directed.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

110 mm bore PVC (SWR) socket/bends/shoes any radius complete all as specified and as directed.

Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm bore complete all as specified and as directed.

Pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm complete all as specified and as directed.

S&F in repair stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Waste fittings brass chromium plated for glazed ware sink, basins,etc with long screwed shank and fly nuts,flenges end bedded in red lead cement and other end fixed 32mm dia complete all as specified and as directed.

S&F in rep stainless steel grating doom75mm/100mm square/round complete all as specified and as directed.

S&F in repair 32/40 mm dia PVC waste pipe for WHB/sink complete all as specified and as directed.

S&F in repair flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed.

S&F in repair 32 mm waste coupling of PTMT ( half or full threaded) (Min weight 60 gms)complete all as specified and as directed.

S&F in repair 40 mm waste coupling of PTMT ( half or full threaded) (Min weight 60 gms) complete all as specified and as directed.

S&F in repairs CP soap dish any type fixed to wall with brass screws complete all as specified and as directed.

Cast Iron floor trap with dia of outlet 75mm with CI grating including jointing to waste pipe fixed in cement concrete PCC 1:2:4 type B-1 complete all as specified and as directed.

Dismantling of cast iron/PVC pipe or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required of internal dia of pipe 100 mm complete all as specified and as directed.

100 mm bore cast iron soil, sand cast, waste and vent pipes in any length with or without ears, with cement joints fixed to walls complete all as specified and as directed.

Cast iron bends (any radius) with for 75mm bore fitted with oval access doors complete all as specified and as directed.

Cast iron bends (any radius),diminishing pieces or tapers (larger bore measured) for 100mm bore fitted with oval access doors complete all as specified and as directed.

Cast iron branch pieces, single (equal of unequal), ordinary or inverted (spigot or socket type) or with parallel branches for 100mm bore fitted oval access door complete all as specified and as directed.

Supply and fixing in repair ball valves of size 20mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and directed by Engr-in-Charge

15mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed.

20mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed.

M&L in repairs Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm complete all as specified and as directed.

M&L in repairs Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm complete all as specified and as directed.

S&F in repair 15mm dia stop cock fancy type chromium plated concealed type, complete all as specified and as directed.

S&F in repair bib tap 15mm bore fancy type chromium plated complete all as specified and as directed.

Bib cock 15 mm bore long body chromium plated in repair complete all as specified and as directed.

Vitreous China wash basin, white, flat back, size 550x400mm excluding tap, chain, plug but including for fixing of taps, waste fitting, brackets and cutting for and pinning in ends of brackets but fixed in repair complete all as specified and as directed.

Brass chromium plated shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union of bore 15 mm, as in repairs complete all as specified and as directed.

S&F in repair tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs,complete all as specified and as directed.

Float valve assembly for flushing cistern with inlet valve float and handle including brackets, fixed in repairs complete all as specified and directed.

Supply and fixing in repairs vitreous china squatting pan, Orrisa pattern of size 580mmx440mmwhite with integral foot rests excluding flushihng cistertn and flush pipe,complete all as specified and as directed.

Cast iron 'P' or 'S' trap for bore of pipe 100mm complete all as specified and as directed.

Supply and fix as in repairs vitreous china wash down water closet pan (pedestal pattern) white plastic water closet seat & back with flat bottom and cover, mild steel chromium plated or aluminium anodised high device (excluding flushing cistern and flush pipe) but including fixing bolt and necessary connection with existing pipes complete all as specified and directed.

Toilet paper holder brass chromium plated with flap all as specified and directed.

10 ltr capacity PVC low level flushing cistern symphonic action type white with inlet valve float and handle including brackets, fixed in repairs complete all as specified and directed.

S&F in repairs of sinks with draining board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repair 1mm thik plate rack made of stainless steel, 600x750x250 mm (Wt not less than 7.5 Kg) including brackets and embedded in brick wall all as specified and as per manufacturers instruction.

S&F in repairs rotational moulded polyethylene water storage tanks three layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 liters including all accessories complete all as specified and as directed.

S&F in repairs for 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and PTMT ball valve 20mm dia and including taking down of old tank and removing from site complete all as specified and as directed.

Glass shelf 600mm long including CP supporting clamps, screws etc, complete all as specified and as directed by Engr-in-Charge. Make : Cat part No AKP-35771P or equivalent as per specifed in PS.

Water proofing treatment to surfaces of walls/concrete slabs damaged due to moisture and efflorescence including sunken areas of bathrooms/toilets, in balconies by applying acrylic polymer modified cementitious high performance coating or treatment all as per manufacturer's instructions, complete all as specified and as directed.

PCC 1: 5 : 10 type E2 using 40 mm graded brick aggregate as in filling under sunken floors etc complete all as specified and as directed.

Door seal for wooden/Aluminium/steel door shutter complete all as specified and as directed by Engr-in-charge/ GE.

Harrison, rails drapery rod powdered coated including brackets and necessary fitting as directed by Engg-in-Charge/ GE.

S&F in reapair aluminum door closer ( aluminum extruded section) hydraullically regulated , designation No 3 , universal type , suitable for door shutters of 851mm to 1000 in width and of weight 61 to 80 kg complete all as specified and as directed.

Rolled mild steel work of angle iron as in frames of doors & Cup Board etc conforming to grade Fe 410-W (Gde E-250) quality 'A" complete all as specified and as directed.

19mm thick ISI, termite proof , chemically well pressed, prelaminated particle board exterior grade prelaminated, one side with decorative choice lamination and other side balancing white lamination fixed with screws to frame work for kitchen cabinetstand & cup boards etc includimg 6mm th teak wood beading all around complete all as specified and directed .

S&F in repair 100 mm long aluminium anodised hasp and staple complete all as specified and as directed.

S&F in repairs aluminum handles cast type, anodised, 150mm size complete all as specified and as directed.

Mild steel cold rolled butt hinges medium weight 75 mm long, including fixing to pressed steel door frame if required complete all as specified and as directed.

M&L Welding in repairs n. exc 6mm thick metal and n. exc 2.5 cm in length complete all as specified and as directed.

M/S GURBACHAN SINGH (BID ID -3097052)

SINGH CONST CO (BID ID -3095459)

M/s LAL DAYAL CONSTRUCTION CO (BID ID -3108807)

PARDEEP SHARMA (BID ID -3096726)