Construction of ZP school building at Anjaneri village Taluka Trambakeshwar District Nashik

HINDUSTAN AERONAUTICS LIMITED AIRCRAFT OVERHAUL DIVISION, NASIK WORKS AND SERVICES DEPARTMENT

Name of work: “CONSTRUCTION OF ZP SCHOOL BUILDING AT ANJANERI VILLAGE, TALUKA TRAMBAKESHWAR, NASHIK.”

Tender No.:NK/FW/CSR-1637/2025-26

NIT NO. : NK/FW/575/2025-26

Estimate Value : Rs. 272.23 Lakhs

PRICE BID/ COMMERCIAL BID PART-B

Name of the Tenderer:

Sl. No Specification Unit Quantity Rate in Figs [Excluding GST] Rate in words Amount

Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The tenderer shall abide by prevailing GST act. (2) This BOQ specifications have to be read in conjunction with detailed technical specification and tender drawings if any. (3) The quoted percentage for the works mentioned below, shall be taken into consideration for evaluation of the tender. The lowest offer (L-1) will be determined considering the total amount including GST based on the quoted percentage.

Part A : Civil Works

1 Demolishing cement concrete of nominal concrete 1:3:6 or richer mix (including equivalent design mix) manually/ by mechanical means in any position including disposal of material/debris off the site within 50 metres lead and stacking for further disposal all complete and as per direction of EIC. Cum 1.00 2234.15 Rupees Two Thousand Two Hundred Thirty Four and Fifteen Paise Only 2,234.15

2 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m all complete as directed and as specified by EIC. Note: The item will not be paid whereever any other excavation items are paid. Sqm 800.00 31.35 Rupees Thirty One and Thirty Five Paise Only 25,080.00

3 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation, trenches, drains or like (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lifts , including getting out the excavated soil and disposal of surplus excavated soil , within a lead of 50 m all complete and as directed by EIC. Note: Soil, if any, which is required for refilling shall be stacked at site as per the directions of EIC. 0.00

a) All kinds of soil Cum 45.00 238.91 Rupees Two Hundred Thirty Eight and Ninety One Paise Only 10,750.95

b) Ordinary rock Cum 45.00 580.92 Rupees Five Hundred Eighty and Ninety Two Paise Only 26,141.40

c) Hard rock (Blasting Prohibited) Cum 75.00 1397.86 Rupees One Thousand Three Hundred Ninety Seven and Eighty Six Paise Only 104,839.50

4 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift as directed by Engineer-in-charge. 0.00

a) All kinds of soil Cum 50.00 162.91 Rupees One Hundred Sixty Two and Ninety One Paise Only 8,145.50

b) Ordinary rock Cum 10.00 457.89 Rupees Four Hundred Fifty Seven and Eighty Nine Paise Only 4,578.90

c) Hard rock (Blasting Prohibited) Cum 5.00 1315.16 Rupees One Thousand Three Hundred Fifteen and Sixteen Paise Only 6,575.80

5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations, floors, etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by mechnical/power ramming/compacting and watering, lead up to 50 m and lift upto 1.5 m all complete as directed by EIC. Cum 150.00 179.89 Rupees One Hundred Seventy Nine and Eighty Nine Paise Only 26,983.50

6 Supplying, stacking and filling murum (including royalty) in trenches, plinth, sides of foundation, floors,etc in layers not exceeding 20cm consolidating each deposited layer by mechnical/power ramming/compacting and watering, lead up to 50 m and lift upto 1.5 m all complete as directed by EIC. Cum 400.00 884.99 Rupees Eight Hundred Eighty Four and Ninety Nine Paise Only 353,996.00

7 Removing the excavated surplus soil / material / dismantled debris including loading, conveying and depositing at a place at a distance upto 1KM from starting point as directed and spreading & levelling all as directed by EIC. Cum 20.00 159.74 Rupees One Hundred Fifty Nine and Seventy Four Paise Only 3,194.80

8 Providing and laying in position 1:2:4 cement concrete (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) including mixing, laying, curing, fininshing to level & line etc all complete for all works up to plinth level as specified and as directed by EIC. Cum 75.00 7230.87 Rupees Seven Thousand Two Hundred Thirty and Eighty Seven Paise Only 542,315.25

9 Providing centering and shuttering including strutting, propping, etc.and removal of formwork for plain or reinforced cement concrete straight, horizontal, sloping as required including all cutting & waste, centering, bracing, all complete as specified & as directed by EIC for: 0.00

a) Footings, foundations, bases of column etc. for mass concrete. Sqm 200.00 359.92 Rupees Three Hundred Fifty Nine and Ninety Two Paise Only 71,984.00

b) Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 500.00 882.28 Rupees Eight Hundred Eighty Two and Twenty Eight Paise Only 441,140.00

c) Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 775.00 675.87 Rupees Six Hundred Seventy Five and Eighty Seven Paise Only 523,799.25

d) Suspended floors, roofs, landings, balconies , shelves, chajja, etc. Sqm 875.00 851.03 Rupees Eight Hundred Fifty One and Three Paise Only 744,651.25

e) Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. Sqm 150.00 773.25 Rupees Seven Hundred Seventy Three and Twenty Five Paise Only 115,987.50

f) Stairs, (excluding landings) except spiral-staircases Sqm 55.00 702.07 Rupees Seven Hundred Two and Seven Paise Only 38,613.85

10 Providing and laying in position ready mixed or site batched design mix cement concrete of M25 grade (minimum cement content of 330 Kg/Cum) for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, ordinary portland cement, admixtures (for RMC) in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge. 0.00

a) All works upto plinth level Cum 115.00 8723.43 Rupees Eight Thousand Seven Hundred Twenty Three and Forty Three Paise Only 1,003,194.45

b) All works above plinth level upto floor V level Cum 250.00 9049.85 Rupees Nine Thousand Forty Nine and Eighty Five Paise Only 2,262,462.50

11 Providing and laying in position ready mixed cement concrete of M30 grade (mimimum cement content of 350 Kg/Cum) for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge. 0.00

a) All works upto plinth level Cum 5.00 8861.97 Rupees Eight Thousand Eight Hundred Sixty One and Ninety Seven Paise Only 44,309.85

12 Providing and laying in position MS reinforcement TMT of grade Fe-500D or more, for R.C.C. work including straightening, cutting to required length, bending, hooking, cranking, placing in position and binding with MS wire (annealed) not less than 0.9 mm Dia. or securing with clips including necessary lapping, spacers/cover blocks complete all as specified and as directed by EIC. Kgs. 31000.00 98.99 Rupees Ninety Eight and Ninety Nine Paise Only 3,068,690.00

13 Supplying, stacking, laying, spreading & compacting stone aggregate in required thickness hand picking, consolidating with mechnical vibrator in stages with proper grade and camber, level, applying and brooming requiste type of screening/binding material to fill up interstices of coarse aggregate, watering and compacting to required density all complete as per direction of Engineer-in-charge. Note: binding material shall be with stone dust to be filled in interstices of coarse aggregate. 0.00

a) Stone aggregate of size 90mm to 63mm Cum 55.00 2881.98 Rupees Two Thousand Eight Hundred Eighty One and Ninety Eight Paise Only 158,508.90

14 Providing and constructing brick masonry in subclass 'B' Bricks , straight or curved on plan to any radius built in CM 1:4 above or below ground at any height and level including necessary scaffolding, curing , providing reinforcement, if required, all complete as specified and as directed by the EIC. (Brick of class designation 35kgf/cm2)(MS reinforcement will be paid separately under respective item). Cum 75.00 8917.78 Rupees Eight Thousand Nine Hundred Seventeen and Seventy Eight Paise Only 668,833.50

15 Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm to 300 mm thick with Grade-I AAC blocks of density 551 to 650 Kg/Cum. conforming to IS2185(Part 3) in super structure above plinth level upto floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). cum 230.00 7648.60 Rupees Seven Thousand Six Hundred Forty Eight and Sixty Paise Only 1,759,178.00

16 Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design as specified and as directed by EIC. Cum 3.00 2652.53 Rupees Two Thousand Six Hundred Fifty Two and Fifty Three Paise Only 7,957.59

17 Providing and applying 18 mm cement plaster on brick/AAC/concrete surface in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge at any height and level including scaffolding, curing, etc. all complete as specified and as directed by EIC. Sqm 1045.00 493.00 Rupees Four Hundred Ninety Three Only 515,185.00

18 Providing and applying 15 mm thick cement plaster finished with a floating coat of neat cement of mix : 1:6 (1 cement: 6 fine sand) with neeru finish to concrete/AAC/ brick surfaces, in all positions and level including scaffolding, curing etc. complete as specified and as directed. Sqm. 1930.00 365.98 Rupees Three Hundred Sixty Five and Ninety Eight Paise Only 706,341.40

19 Providing and applying 6mm thick cement plaster on ceiling in cement mortar 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and neeru finish all complete as specified and as directed by EIC. Sqm 820.00 364.05 Rupees Three Hundred Sixty Four and Five Paise Only 298,521.00

20 Providing & applying cement plaster 15 mm thick in cement mortar 1:4 (1 cement: 4 fine sand) to concrete/AAC/brick surfaces with floating coat of neat cement at any level and position including scaffolding,curing, etc. all complete as specified and as directed by EIC. Sqm 50.00 438.62 Rupees Four Hundred Thirty Eight and Sixty Two Paise Only 21,931.00

21 Providing and applying 6mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge at bottom of chajja, slab projections and like at any height and level including scaffolding, curing, etc. all complete as specified and as directed by EIC. Sqm. 115.00 275.76 Rupees Two Hundred Seventy Five and Seventy Six Paise Only 31,712.40

22 Providing and applying white cement based putty of 2 mm thickness over plastered surface of approved brand and manufacturer to prepare the surface even and smooth complete as diected by EIC. Sqm. 1930.00 157.03 Rupees One Hundred Fifty Seven and Three Paise Only 303,067.90

23 Providing and applying two coats of acrylic emulsion paint on walls or ceiling of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour including priming coat with water thinnable cement primer having VOC content less than 50grams/litre all complete as specified and as diected by EIC. Sqm. 1580.00 224.29 Rupees Two Hundred Twenty Four and Twenty Nine Paise Only 354,378.20

24 Providing, applying and finishing exterior walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shades with Two or more coats (applying additional coats wherever required, to achieve even shade and colour) applied @ 1.43 ltr/10 sqm of approved quality, brand having VOC content less than 50 grams / Litre (Asian -Apex Ultima Protek Duralife/ Nerolac - Excel Everlast 12 / Berger – Weathercoat Long Life 15 or equivalent) over and including priming coat of acrylic water based exterior alkali resistant primer with silicon additive or equivalent of approved quality, brand & applying with roller for fair finish as approved by EIC on old work over existing paint surface including all as specified and as directed by EIC. Sqm 1045.00 147.40 Rupees One Hundred Forty Seven and Forty Paise Only 154,033.00

25 Providing and applying two coats of synthetic enamel paint on walls/steel of approved colour to give even shade all complete as specified and as directed by EIC. Sqm 350.00 94.35 Rupees Ninety Four and Thirty Five Paise Only 33,022.50

26 Providing and laying in position polished Granite stone Black, Cherry/ Ruby red or equivalent in flooring,steps,sills, etc. of required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Sqm 180.00 4112.93 Rupees Four Thousand One Hundred Twelve and Ninety Three Paise Only 740,327.40

27 Providing edge moulding to 18 mm thick to granite including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Rmt 500.00 468.95 Rupees Four Hundred Sixty Eight and Ninety Five Paise Only 234,475.00

28 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 0.00

a) Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 600mm Sqm 270.00 1344.44 Rupees One Thousand Three Hundred Forty Four and Forty Four Paise Only 362,998.80

b) Double charge vitrified tile of polish finish of size 600 x 1200mm Sqm. 660.00 1447.51 Rupees One Thousand Four Hundred Forty Seven and Fifty One Paise Only 955,356.60

29 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, dado over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) , jointing with gray cement slurry @ 3.3 Kg/sqm including grouting the joint with cement & matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Sqm. 55.00 1489.63 Rupees One Thousand Four Hundred Eighty Nine and Sixty Three Paise Only 81,929.65

30 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Sqm 360.00 1021.24 Rupees One Thousand Twenty One and Twenty Four Paise Only 367,646.40

31 Providing and fixing ISI marked 30mm flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood including ISI marked Stainless Steel butt hinges with necessary SS screws all complete as specified and as directed by EIC. Sqm 50.00 3333.00 Rupees Three Thousand Three Hundred Thirty Three Only 166,650.00

32 Providing & Fixing 1.0 mm thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish as approved with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality all complete as specified and as directed by EIC. Sqm. 100.00 823.54 Rupees Eight Hundred Twenty Three and Fifty Four Paise Only 82,354.00

33 Providing and fixing bright finished brass door latch of size 300 x 16 x 5mm with necessary screws etc. all complete as specified and as directed. Nos 26.00 295.72 Rupees Two Hundred Ninety Five and Seventy Two Paise Only 7,688.72

34 Providing and fixing bright finished brass tower bolts (barrel type) of size 200 x 10mm with necessary SS screws etc. all complete as specified and as directed. Nos 11.00 328.94 Rupees Three Hundred Twenty Eight and Ninety Four Paise Only 3,618.34

35 Providing and fixing 125mm bright finished brass handles with screws etc. all complete as specified and as directed. Nos 52.00 235.56 Rupees Two Hundred Thirty Five and Fifty Six Paise Only 12,249.12

36 Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, screws etc. to suit shutter thickness all complete as specified and directed. Nos. 14.00 249.14 Rupees Two Hundred Forty Nine and Fourteen Paise Only 3,487.96

37 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 0.00

a) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). Kg 950.00 549.40 Rupees Five Hundred Forty Nine and Forty Paise Only 521,930.00

b) Providing and fixing fly proof wire gauze of Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides fixed in aluminium work of windows, clerestory windows and doors all complete as directed by EIC. Sqm. 75.00 1040.37 Rupees One Thousand Forty and Thirty Seven Paise Only 78,027.75

c) Providing & fixing Window Lock as approved by EIC. Nos. 150.00 95.87 Rupees Ninety Five and Eighty Seven Paise Only 14,380.50

d) Providing & fixing of SS body with single nylon roller (weight bearing capacity to be 40kg) for sliding windows complete and as specified. Each 300.00 63.33 Rupees Sixty Three and Thirty Three Paise Only 18,999.00

e) Providing & fixing Wool Pile for sliding window complete and as specified. RM 540.00 20.20 Rupees Twenty and Twenty Paise Only 10,908.00

38 Providing and fixing with float glass of panes 5.0 mm thickness (weight not less than 12.50 Kgs/sqm) glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): Sqm 150.00 1381.52 Rupees One Thousand Three Hundred Eighty One and Fifty Two Paise Only 207,228.00

39 Providing and fixing M.S. grills of approved/required pattern in frames of windows, ventilators, etc. with M.S. flats, square or round bars, etc. including fixing to opening with holdfasts, screws,etc. including priming coat with approved steel primer all complete as specified and as directed. Kg 2830.00 218.76 Rupees Two Hundred Eighteen and Seventy Six Paise Only 619,090.80

40 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Kg 250.00 708.91 Rupees Seven Hundred Eight and Ninety One Paise Only 177,227.50

41 Providing and laying with average thickness of 120 mm and minimum thickness at khurra as 65 mm integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mmheight including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved byEngineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. Sqm 160.00 1546.13 Rupees One Thousand Five Hundred Forty Six and Thirteen Paise Only 247,380.80

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge. 0.00

42 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work , including cutting chases and making good the walls,etc. 0.00

(a) 15mm dia. RM 20.00 456.88 Rupees Four Hundred Fifty Six and Eighty Eight Paise Only 9,137.60

(b) 20mm dia. RM 30.00 493.41 Rupees Four Hundred Ninety Three and Forty One Paise Only 14,802.30

(c) 25 mm dia. RM 120.00 575.69 Rupees Five Hundred Seventy Five and Sixty Nine Paise Only 69,082.80

(d) 32 mm dia. RM 50.00 678.53 Rupees Six Hundred Seventy Eight and Fifty Three Paise Only 33,926.50

43 Providing and fixing gun metal valve of CI wheel of approved quality (screwed end) all complete as specified and as directed. 0.00

a) 25mm Nos 2.00 571.24 Rupees Five Hundred Seventy One and Twenty Four Paise Only 1,142.48

b) 32mm Nos 2.00 632.92 Rupees Six Hundred Thirty Two and Ninety Two Paise Only 1,265.84

44 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm standard size C.P. brass flush pipe, spreaders with unions and clamps with waste fitting as per IS : 2556 and cutting and making good the walls and floors wherever required all complete and as specified. Each 12.00 6602.77 Rupees Six Thousand Six Hundred Two and Seventy Seven Paise Only 79,233.24

45 Providing and fixing white vitreous china water closet squatting pan of size 580 x 440mm (Indian type-Orissa pattern) setting in position in lime concrete including providing and fixing ' P' or ' S ' traps, connecting to soil/ drainage pipe , providing and fixing 10 liters capacity PVC low level flushing cistern of approved shade including flushing pipe with manually controlled device handle (hnadle lever) conforming to IS:7231 with all fittings and fixtures making good walls and floor wherever required complete as specified and as directed. Nos 8.00 6211.10 Rupees Six Thousand Two Hundred Eleven and Ten Paise Only 49,688.80

46 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with same brand solid plastic seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required all complete as specified and as directed. Each 4.00 5979.95 Rupees Five Thousand Nine Hundred Seventy Nine and Ninety Five Paise Only 23,919.80

47 Providing and fixing white vitreous China Wash basin of size 550x400 mm with necessary brackets/anchor bolts including providing and fixing 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, including cutting and making good the walls wherever require complete as specified and as directed. Nos 8.00 1724.73 Rupees One Thousand Seven Hundred Twenty Four and Seventy Three Paise Only 13,797.84

48 Providing and fixing 20mm nominal bore, 120mm long (weight not less than 198 gms) PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball all complete as specified and as directed. Nos 4.00 236.43 Rupees Two Hundred Thirty Six and Forty Three Paise Only 945.72

49 Providing and fixing 15 mm nominal bore CP brass stop/angle cock of approved quality conforming to IS 8931 as spcified and as directed. Nos 36.00 324.22 Rupees Three Hundred Twenty Four and Twenty Two Paise Only 11,671.92

50 Providing and fixing 15mm nominal bore CP brass bib cock of approved quality confirming to IS:8931 as specified and as directed. (Weight not less than 400 gms.) Nos 18.00 324.22 Rupees Three Hundred Twenty Four and Twenty Two Paise Only 5,835.96

51 Providing and fixing 8mm dia CP/SS jet with flexible tube upto 1 meter long with SS triangular plate to EWC of approved brand and quality complete as specified and directed by EIC. Each 6.00 320.45 Rupees Three Hundred Twenty and Forty Five Paise Only 1,922.70

52 Providing and fixing 15mm nominal bore and 450mm long unplasticised PVC connection with brass unions/nuts complete as directed. Each 50.00 89.72 Rupees Eighty Nine and Seventy Two Paise Only 4,486.00

53 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 0.00

(a) 75mm dia. RM 20.00 227.71 Rupees Two Hundred Twenty Seven and Seventy One Paise Only 4,554.20

(b) 110mm dia. RM 150.00 346.38 Rupees Three Hundred Forty Six and Thirty Eight Paise Only 51,957.00

54 Providing and fixing in position approved and ISI brand PVC SWR drainage pipes in floors/ trenches or wall including connecting to drainage lines and sanitary wares, clamping with necessary fasteners or laying in trenches. The drainage lines are required to be tested for leakages all complete as specified and as directed. Earth work wherever required will be paid seperately. 0.00

a) 160mm dia. RM 50.00 739.38 Rupees Seven Hundred Thirty Nine and Thirty Eight Paise Only 36,969.00

55 Providing and fixing in position approved and ISI brand PVC SWR fittings to drainage pipes as below: 0.00

i) 75mm Nos 10.00 97.20 Rupees Ninety Seven and Twenty Paise Only 972.00

ii) 110 mm Nos 10.00 138.00 Rupees One Hundred Thirty Eight Only 1,380.00

b) Shoe plain Bends 0.00

i) 75mm Nos 2.00 85.45 Rupees Eighty Five and Forty Five Paise Only 170.90

ii) 110 mm Nos 20.00 121.02 Rupees One Hundred Twenty One and Two Paise Only 2,420.40

c) Single Tee with door 0.00

i) 75x75x75mm Nos 5.00 150.71 Rupees One Hundred Fifty and Seventy One Paise Only 753.55

ii) 110 x110x110mm Nos 5.00 214.91 Rupees Two Hundred Fourteen and Ninety One Paise Only 1,074.55

d) Single Tee without door 0.00

i) 75x75x75mm Nos 5.00 132.44 Rupees One Hundred Thirty Two and Forty Four Paise Only 662.20

ii) 110 x110x110mm Nos 5.00 203.16 Rupees Two Hundred Three and Sixteen Paise Only 1,015.80

56 Providing and fixing P.V.C. long arm Nahani Trap of 110x75mm diameter including grating, bend and connecting piece upto the outside face of the walls making good damaged surface, testing etc. complete as directed by Engineer in charge. Nos 14.00 80.28 Rupees Eighty and Twenty Eight Paise Only 1,123.92

57 Providing and fixing PVC (SWR) cowl cap 75mm dia. with necessary fixing arrangement as directed. Nos 4.00 15.28 Rupees Fifteen and Twenty Eight Paise Only 61.12

58 Providing and fixing 18mm thick Pre-laminated medium density fibre board with decorative lamination on one side and balancing lamination on one side Grade - I (exterior grade) confirming to IS:14587 fixed to steel/wooden framework for preparation of shelves, school benches, tables, cubboard, chairs, other furnitures, etc with screws/nut bolts having oval head and fittings, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand all complete as directed by EIC. Sqm 190.00 1299.33 Rupees One Thousand Two Hundred Ninety Nine and Thirty Three Paise Only 246,872.70

59 Providing and fixing mild steel tubes joints mitred and welded including fixing applying a priming coat of approved steel primer and two coat of synthetic enamel paint for steel framework for preperation of shelves, school benches, tables etc all complete as per the direction of Engineer-In-charge. Kg 4000.00 147.97 Rupees One Hundred Forty Seven and Ninety Seven Paise Only 591,880.00

60 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern Sqm. 400.00 1001.78 Rupees One Thousand One and Seventy Eight Paise Only 400,712.00

61 Supply and fixing writing Board of size 2400mmX 1200mm magnetic green dry erase (front surface shall be ceramic steel ) with core material 9 mm thick, suitable for writing with chalk with back cover of Galvanised steel sheets and strips as per IS 277, inclduig frame of 1.2mm wall thickness of aluminium alloy as per IS 1285 with ABS corners all complete as specified & as directed by EIC. Nos 9.00 8259.07 Rupees Eight Thousand Two Hundred Fifty Nine and Seven Paise Only 74,331.63

62 Supply and fixing green/blue fabric Pin up notice board 1200mm X 900mm having 11mm overall pinablity depth of board of front layer thickness 2mm with core material thickness of 9mm of soft board. The rear panel shall be of Galvanised iron sheet and aluminium frame having corner protection including wall fixing kit,etc. all complete as specified and as directed by EIC. Nos 5.00 3830.13 Rupees Three Thousand Eight Hundred Thirty and Thirteen Paise Only 19,150.65

63 Planting botanical plants and shrubs, including digging of pits of size 0.30x0.30x0.30m and shall be manured , after the manure has been broken down to powder, the mixture shall be filled in to the hole up to the level of adjoining ground and then profusely watered and enable the soil to subside the refilled soil shall then be dressed evenly with its surface about 50 to 75 mm below the adjoining ground level or as directed by the Engineer-in-charge.removing unwanted material to outside of that particular garden/site including stacking (if require) and watering after planting. (Note: Plants will be supplied under respective item) Nos. 40.00 51.62 Rupees Fifty One and Sixty Two Paise Only 2,064.80

64 Supplying specified botanical plants of specified height (in feet) as detailed below: 0.00

a) Areca Palm - 4ft height Nos 20.00 209.75 Rupees Two Hundred Nine and Seventy Five Paise Only 4,195.00

b) Thuja - 3ft height Nos. 20.00 376.62 Rupees Three Hundred Seventy Six and Sixty Two Paise Only 7,532.40

65 Supply and fixing of acrylic name board (double layer) on brick/concrete surface with pasting acrylic letters/alphabets/symbols/layer of 3mm thick with suitable adhesive over transparent acrylic sheet/layer of 4mm thick drilled with screws, etc. in line,level, at all height/position all complete as directed.Note: Alphabets may be in Hindi/English/Marathi as per direction of EIC. Sqm. 4.00 5140.38 Rupees Five Thousand One Hundred Forty and Thirty Eight Paise Only 20,561.52

66 Supply and fixing acrylic letters/alphabets/symbols of 3mm thick and UV printed HAL logo pasting with suitable adhesive/self adhesive over ACP panel 3mm thick supported over MS hollow sections of size 25mm x25mm x 2.6mm thick in proper line, level, at all height,positions including transportation, etc.all complete as diretced. Note: Alphabets may be in Hindi/English/Marathi as per direction of EIC. Sqm. 7.00 7229.07 Rupees Seven Thousand Two Hundred Twenty Nine and Seven Paise Only 50,603.49

67 Supply and fixing name board of 3 mm acrylic transparent board with radium background along with radium letters for classroom nomenclature all complete as directed. Note: Alphabets may be in Hindi/English/Marathi as per direction of EIC. Sqm. 10.00 5140.39 Rupees Five Thousand One Hundred Forty and Thirty Nine Paise Only 51,403.90

68 Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge. Sqm. 10.00 2828.61 Rupees Two Thousand Eight Hundred Twenty Eight and Sixty One Paise Only 28,286.10

69 Writing Letters --- Writing letters or figures ( Block, Roman, Italic or Indian) not exceeding 30 cm high of approved colour, shade & fashion complete all as specified & as directed by EIC. (Letters etc., shall be painted with thick paint, so that they stand out boldly and solidly without showing signs of brush marks, if necessary, they shall be repainted until the desired result is obtained.) Each 300.00 5.65 Rupees Five and Sixty Five Paise Only 1,695.00

70 Providing and placing on terrace polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank all complete as specified and as directed.(Capacity of each Tank may be 1000/2000lit as required and directed.) Litre 6000.00 10.10 Rupees Ten and Ten Paise Only 60,600.00

71 Providing & fixing in position colour coated corrugated galvalume sheet of 0.50 mm thick (total coated thickness) having high tensile strength of 550 mpa, with metallurgical coating of zinc aluminium alloy of 150 grams /Sqm (AZ 150) (both side inclusive ) conforming to ASTM -792 & AS 1397 having profile depth approximate 28mm high rib with subtle square fluting in the pan and the end rib shall have anti-capillary groove and return leg for roofing / cladding/ridge including sheet shall be fastened with 40μm zinc coated or 25μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners with neoprene/EPDM washers. The sheet will have coating of minimum 20 microns of painting over corrosion inhibiting primer (min 5 micron) on top side & standard backing coat on reverse side. All penetrations and laps shall be sealed with silicon or equivalent sealants while laying the sheet. End overlap wherever required shall be minimum 150 mm & side lap are full rib as per manufacture catalogues. Sqm 300.00 944.35 Rupees Nine Hundred Forty Four and Thirty Five Paise Only 283,305.00

72 Providing and fixing in position steel work in built up tubular (Electric resistance or induction butt welded tubes-round, square or rectangular hollow tubes, etc.) trusses,shed,gates, etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. all complete as directed. Kg 2600.00 177.93 Rupees One Hundred Seventy Seven and Ninety Three Paise Only 462,618.00

Part B : Electrical Works

73 Supply And Installation Of SPN 12 Way, Double Door, Distribution Board (D.B.) Make: Siemens / L & T / ABB / C&S NOS 4.00 2118.81 Rupees Two Thousand One Hundred Eighteen and Eighty One Paise Only 8,475.24

74 Supply And Installation Of 63 Amp., DP MCB, Breaking Capacity 10KA, Make: Siemens / L & T / ABB / C&S/ Legrand NOS 4.00 482.37 Rupees Four Hundred Eighty Two and Thirty Seven Paise Only 1,929.48

75 Supply And Installation Of 6 A To 32 Amp.,Breaking Capacity 10KA, SP MCB Make: Siemens / L & T / ABB / C&S/ Legrand NOS 48.00 234.31 Rupees Two Hundred Thirty Four and Thirty One Paise Only 11,246.88

76 Supply And Installation Of 16 Amp / 20 Amp., DP MCB, Breaking Capacity 10KA, for control at each class room / office / toilet / hall etc. Make: Siemens / L & T / ABB / C&S/ Legrand NOS 19.00 600.41 Rupees Six Hundred and Forty One Paise Only 11,407.79

77 Supply of materials & carry out point wiring (for fans, lights, etc.) using “HAVELLS / ANCHOR / FINOLEX / POLYCAB / TORRENT” make 1.5 Sq.mm. stranded copper conductor, PVC insulated wire & 1.0 Sq.mm copper earth wire, “PRECISION / MODI / FINOLEX / POLYCAB / PRESSFIT” make PVC conduit / casing capping, “ANCHOR / M.K / LEON/ L & T " make 6A modular switch, socket, modulr metal flush box, modular surface plate, ceiling roses etc. Note: 1) Measurement shall be “point wiring” wise and one switch controlling one point shall be counted as one point. 2) Switch & socket installed on same board will be treated as half point. (3) This is a conceal-wiring work. NOS 230.00 1342.68 Rupees One Thousand Three Hundred Forty Two and Sixty Eight Paise Only 308,816.40

78 Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR is PVC insulated copper conductor, single core cable in surface/ recessed as required. 2x2.5 sq. mm + 1x1.5 sq. mm earth wire. Wire / Cable Make: HAVELLS / ANCHOR / FINOLEX / POLYCAB / TORRENT M 630.00 251.69 Rupees Two Hundred Fifty One and Sixty Nine Paise Only 158,564.70

79 Supply of materials & carry out point wiring using HAVELLS / ANCHOR / FINOLEX / POLYCAB / TORRENT make 2.5 Sq.mm. copper conductor, PVC insulated wire & 1.5 Sq.mm copper earth wire, PRECISION / MODI / FINOLEX / POLYCAB / PRESSFIT make PVC conduit / casing capping, ANCHOR / M.K. / LEON / L & T make 16A, 3 module, modular switch, socket, modular metal flush box, modular surface plate etc. Note: 1) Measurement shall be “point wiring” wise. NOS 30.00 1665.76 Rupees One Thousand Six Hundred Sixty Five and Seventy Six Paise Only 49,972.80

80 Supply and installation of modular stepped type , socket size, electronic fan regulator 230V, Flush type. Make: ANCHOR / M.K. / LEON/ L& T/COLORS NOS 34.00 337.73 Rupees Three Hundred Thirty Seven and Seventy Three Paise Only 11,482.82

81 Supply & Laying Of XLPE Insulated,Armoured Heavy Duty Electric Cable With Aluminium Conductor, 1100 V Grade, 4 Core X Cross Sectio Area 50 Sq.Mm. (Execution as per site requirement.) Make: Finolex/ RR Cables/ Havells/ Polycab M 200.00 198.61 Rupees One Hundred Ninety Eight and Sixty One Paise Only 39,722.00

82 Supply & Laying Of XLPE Insulated,Armoured Heavy Duty Electric Cable With Aluminium Conductor, 1100 V Grade, 4 Core X Cross Sectio Area 10 Sq.Mm. (Execution as per site requirement.) Make: Finolex/ RR Cables/ Havells/ Polycab M 350.00 183.05 Rupees One Hundred Eighty Three and Five Paise Only 64,067.50

83 Supply of 1200 mm. Sweep ceiling fan , colour- white / Ivory of make HAVELLS / KHAITAN / USHA / ORIENT / CROMPTON / BAJAJ with all accessories & carryout out installation. NOS 34.00 2498.72 Rupees Two Thousand Four Hundred Ninety Eight and Seventy Two Paise Only 84,956.48

84 Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp. On pole or wall with the help of necessary fixtures. Make: Bajaj/ Crompton / Havells / Philips / Syska. NOS 6.00 3220.00 Rupees Three Thousand Two Hundred Twenty Only 19,320.00

85 Supply and installation of LED street light fitting, approximately 70 W, with all fixing material like screws, clips etc. 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket / bend pipe with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make: Bajaj/ Crompton / Havells / Philips / Syska. NOS 4.00 2875.00 Rupees Two Thousand Eight Hundred Seventy Five Only 11,500.00

86 Supply and installation of LED batten, 22 W / 24 W, with all fixing material like screws, clips etc. Make: Bajaj/ Crompton / Havells / Philips / Syska. NOS 140.00 230.00 Rupees Two Hundred Thirty Only 32,200.00

87 Supply and installation 20 Amps SPN MCB metallic Plug & Socket. Make: Crompton/ Anchor / Havells/ Standard / C&S NOS 3.00 1069.93 Rupees One Thousand Sixty Nine and Ninety Three Paise Only 3,209.79

88 Cutting chase, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed conduit wiring, etc., and making good, cutting not exc. 10 girth. M 430.00 87.00 Rupees Eighty Seven Only 37,410.00

89 Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel connected to earthing test point all as specified or indicated including testing on completion. NOS 2.00 6838.79 Rupees Six Thousand Eight Hundred Thirty Eight and Seventy Nine Paise Only 13,677.58

90 Supply and installation of TPN 4 Way, Double Door, MCB Distribution Board (D.B.). Make: Siemens / L & T / ABB / C&S / Legrand NOS 1.00 6875.39 Rupees Six Thousand Eight Hundred Seventy Five and Thirty Nine Paise Only 6,875.39

91 Supply and installation of 63 Amp., 4P MCB. Make: Siemens / L & T / ABB / C&S/ Legrand NOS 1.00 2877.56 Rupees Two Thousand Eight Hundred Seventy Seven and Fifty Six Paise Only 2,877.56

92 Supply and fixing LED Solar street light fitting 16 Watt including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete. (Excavation & earth work shall be measured separately) Make of Batteries : TATA / EXIDE / AMARON / SF SONIC / MICROTEK / EMCO NOS 2.00 25300.00 Rupees Twenty Five Thousand Three Hundred Only 50,600.00

93 Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. Make: Bajaj/ Crompton / Havells / Philips / Syska. NOS 16.00 2475.00 Rupees Two Thousand Four Hundred Seventy Five Only 39,600.00

94 Supply and installation of Switch Fuse Unit (SFU) with sheet steel enclosure 500 V, 3 phase with HRC fuses complete with Neutral link of capacity 125 Amps. (Suitable for external / wall mounting.) Make: SIEMENS / STANDARD / C&S / L&T Nos 1.00 4714.47 Rupees Four Thousand Seven Hundred Fourteen and Forty Seven Paise Only 4,714.47

95 Non clog vertical / horizontal submersible pumps with chrome steel impeller and cutter, non-clog to pass 40 mm size particles including Supply, installation with guide rail and lifting chain, cables, Earthing, testing complete with 2 years maintenance. 2 HP Make: LUBI / LAXMI / TAXMO / CROMPTON NOS 1.00 11500.00 Rupees Eleven Thousand Five Hundred Only 11,500.00

Sub-Total (Excluding GST) Rupees Two Crore Thirty Lakh Seventy Thousand Two Hundred Six and Thirty Four Paise Only 23,070,206.34 #REF!

The Tenderer has to Quote Percentage Above / Below as Specified and Percentage Shall be Quoted in Figures. Approximate Basic Amount Put to Tender Select Above or Below Percentage in Figures [Excluding GST] Amount

Tenderer's Quote (Excluding GST) 23,070,206.34 BELOW % 23,070,206.34

Add 18% GST Rupees Forty One Lakh Fifty Two Thousand Six Hundred Thirty Seven and Fourteen Paise Only 4,152,637.14

Grand Total (Including GST) Rupees Two Crore Seventy Two Lakh Twenty Two Thousand Eight Hundred Forty Three and Forty Eight Paise Only 27,222,843.48

Note: (i) The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered. (ii) The quoted rates in the bill of quantities are inclusive of all types of taxes, duties levies, fees and charges etc., imposed by Central/ State Govt. and local bodies Compensation Cess, Labour Cess (if any), Custom Duty, royalties and other levies. It shall also include all other costs including loading, un-loading, insurance, transportation, testing and Certification expenses except GST . GST at the prevailing percentage is added in the BOQ at the end. (iii) While tendering, the contractors do not have to write the rate or estimated cost of each item, but a percentage figure by which the estimate unit rates are to be increased or decreased to be quoted by the contractor and the same percentage figure being applicable to all the items. (iv) In the case of percentage rate tender, the tenderers are required to quote their percentage below/above the rates in the price Bid. In the event of arithmetical error, the quoted percentage will be taken into account for evaluation not the amount. Accordingly corrections will be incorporated in the comparative statement. (v) In case the lowest tendered amount (estimated cost + amount worked on the basis of percentage above/below) of two or more contractors is same, such lowest contractors will be asked to submit sealed revised offer in the form of letter or through e-portal mentioning percentage above/ below on estimated cost of tender including all sub sections/sub heads as the case may be, but the revised percentage quoted above/below on tendered cost or on each sub section/ sub head should not be higher than the percentage quoted at the time of submission of tender. The lowest tender shall be decided on the basis of revised offers. (vi) In case any of such contractors refuses to submit revised offer, then it shall be treated as withdrawal of his tender before acceptance and 50% of earnest money shall be forfeited. If the revised tendered amount of two more contractors received in revised offer is again found to be equal, the lowest tender, among such contractors, shall be decided by draw of lots in the presence of Tender opening committee. (vii) In case all the lowest contractors those have quoted same tendered amount, refuse to submit revised offers, then tenders are to be recalled after forfeiting 50% of EMD of each contractor. Contractor(s), whose earnest money is forfeited because of non submission of revised offer, shall not be allowed to participate in the re-tendering process of the work.

Warning;- Please enter pecentage Quote ;

HINDUSTAN AERONAUTICS LIMITED

AIRCRAFT OVERHAUL DIVISION, NASHIK

Pre-Qualification Profile

Tender Ref No. or Contract No.: NK/FW/CSR-1637/2025-26

Tender Notice no.: NK/FW/575/2025-26

Name of Work: Construction of ZP school building at Anjaneri village, Taluka Trambakeshwar, District Nashik

Estimated Amount in ₹ Lakhs: 272.23

Contract Period in Months 11

Earnest Money Deposit (EMD) in ₹ 544,500.00

Name of the Individual / Firm / Company: * Mandatory

Sl.No Description Details Remarks

1.0 Essential/ Prequalification Criteria

1.1 Annual Turnover: Average annual financial turnover during the last 3 years, ending 31.03.2024 should be at least 30% of the approximate estimated amount put to tender. (i.e ₹ In Lakhs) 81.67

Financial YEAR Turn over (Rs. In Lakhs) Remarks

2021-22 Profit & loss statement duly certified by chartered accountant with UDIN shall be considered for evaluation of turnover for the respective financial Year.

Average Annual Turnover of last Three Financial Years Rs. 0.00 Not meeting eligible criteria

1.2 Solvency : The solvency required will be 40% of the approximate estimated amount put to tender. The solvency certificate shall be from a nationalized or scheduled bank and issued within a period of 12 Months from the final date of submission of the tender i.e ₹ In Lakhs 108.90

Name of Bank & Branch Issued Related Document to be Uploaded to eProcurement Portal.

Date of Issue [DD-MM-YYYY]:

Value (₹ In Lakhs) Not meeting eligible criteria

1.3 Experience Experience of having successfully completed similar works(Refer NIT "Work Details") during last 7 years ending on the previous day of last day of submission of tender should be either of the following: [Latest work experience certificate may be uploaded] a) Three similar completed works each costing not less than the amount equal to 40% of the approx. estimated amount put to tender against each work in the tender notice. (Or) b) Two similar completed works each costing not less than the amount equal to 50% of the approx. estimated amount put to tender against each work in the tender notice. (Or) c) One similar completed work costing not less than the amount equal to 80% of the approx. estimated amount put to tender against each work in the tender notice.

Completed similar works during last 7 years Drop down and Select No.of works

Work No I Type of Work: [Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal. (Refer NIT clause 1.3 for details)

Brief Description of Work:

Completed value of Work in ₹ Lakh:

Date of Commencement of Work [DD-MM-YYYY]:

Date of Actual Completion of Work [DD-MM-YYYY]:

Work No II Type of Work: [Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal. (Refer NIT clause 1.3 for details)

Brief Description of Work:

Completed value of Work in ₹ Lakh:

Date of Commencement of Work [DD-MM-YYYY]:

Date of Actual Completion of Work [DD-MM-YYYY]:

Work No III Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal. (Refer NIT clause 1.3 for details)

Brief Description of Work:

Completed value of Work in ₹ Lakh:

Date of Commencement of Work [DD-MM-YYYY]:

Date of Actual Completion of Work [DD-MM-YYYY]:

1.4 GST No Registration Number. Related Document to be Uploaded to eProcurement Portal. (GST Registration certificate )

1.5 ESIC Registration Number Related Document to be Uploaded to eProcurement Portal. (ESIC registration certificate issued on or before last date of online tender submission date)

1.6 EPF Registration Number Related Document to be Uploaded to eProcurement Portal. (upload EPF registration certificate and required to comply with the provisions of PF act, and as Refered in NIT clause 1.6)

1.7 Bid Capacity ( 2AN-B)

N number of years prescribed for completion of subject project / contract 0.92 number of years prescribed for completion of subject project / contract (indicate contract period N years)

A Value of the work executed in last five Financial years (Financial year wise) Values (₹ in Lacs) (Required for bid capacity calculation)

2019-20 Related documents to be uploaded in eprocurement portal.

A = maximum value of works executed in any one year during last five years at current price level. To work out value of work executed during previous years at current price level a weightage of 10 % per year should be applied. Value of works executed during last five years shall be certified by chartered accountant and shall be considered for evaluation. (₹ in Lakhs) 0.00

B B = value at current price level of existing commitment and ongoing works to be completed in the next ‘N’ years. Works on hand to be uploaded and this statement should be submitted duly verified by Chartered Accountant. Balance Value of the existing commitments and on-going works (Works in hand/in progress in next N years as per NIT) (Refer NIT clause 1.7 for details). Related documents to be uploaded in eprocurement portal.

Available Bid Capacity =2(A X N) - B 0.00 Not meeting eligible criteria

1.8 Earnest Money Deposit (EMD) details Scanned copy of EMD payment to be Uploaded to eProcurement Portal. (Refer NIT clause 1.8 for details)

1.9 License: License for execution of Electrical works and other specialized works from the concerned authorities /organizations/bodies. Related Document to be Uploaded to eProcurement Portal. (Refer NIT clause 1.9 for details)

B Documents to be uploaded along with tender

2.1 Constitution, legal status along with attested copies of Deeds / Articles and Memorandum of Association, etc., as applicable. Related Document to be Uploaded to eProcurement Portal.

Type of ownership

If Other, please specify

2.2 Power of Attorney in case of Pvt. Limited/limited companies Related Document to be Uploaded to eProcurement Portal.

2.3 Details of person holding the power of Attorney.

Name Related Document to be Uploaded in eProcurement Portal. (Original /Attested / Notarized)

Ph. No. with STD code

2.4 Registration with HAL/ Other organization if any. Related Document to be Uploaded to eProcurement Portal.

2.5 Copy of PAN card issued by Income tax authority Related Document to be Uploaded to eProcurement Portal.

2.6 I.T Returns for past 03 years (Assesment Year)

2022-23 Related documents to be uploaded in eprocurement portal.

2.7 Details of ECS viz.,where payments are to be credited along with the scan copy of Blank Cheque leaf

Blank Cheque leaf Blank Cheque leaf to be Uploaded in eProcurement Portal.

Bank Account No. ECS Bank details as per Annexure in tender documents , signed and sealed by concerned bank to be Uploaded to eProcurement Portal.

Name of the Bank

Type of Account

2.8 Annual turnover for last Five years Related documents to be uploaded in eprocurement portal.

2.9 Plant and machinery details for the work. Related documents to be uploaded in eprocurement portal.

2.10 Proposed work completion schedule in the form of bar- chart. Related documents to be uploaded in eprocurement portal.

2.11 Bank Balance statement for last three months.

May-25 Related documents to be uploaded in eprocurement portal.

2.12 Overdraft facilities available with the agencies. Related documents to be uploaded in eprocurement portal.

2.13 Balance sheet for the last Five years

2019-20 Related documents to be uploaded in eprocurement portal.

2.14 Work on hand Related documents to be uploaded in eprocurement portal.

2.15 Udertaking Annexure-K Related Document to be Uploaded to eProcurement Portal.

2.16 Address for correspondence:

2.17 Contact details

Contact person name

Ph. No. with STD code

FAX No. with STD code

3.0 Acceptance by party for Scope of work as per BOQ and Tender terms & conditions Accepted

4.0 DECLARATION

a The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions (Page 1 to 175) including price bid do hereby accept all the terms and conditions laid down. Accepted

b I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. Accepted