Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹64.3 LAccepted-AOC | ₹64.3 L Quoted ₹65.5 L | L1 | Accepted-AOC BEING LOWEST |
| 2 | L2₹74.4 LRejected-Finance 499 A VIDHYUT NAGAR A AJMER ROAD JAIPUR 302021 | JAIPUR | JAIPUR | RAJASTHAN | 302021 | ₹74.4 L | L2 | Rejected-Finance BEING NOT LOWEST |
| 3 | L3₹86.3 LRejected-Finance | ₹86.3 L | L3 | Rejected-Finance BEING NOT LOWEST |
| 4 | Rejected-Technical | - | - | Rejected-Technical TWO CLASS BELOW |
| Sl No | Description | Qty | Unit | AMIT RISHABH BUILDERS PVT LTD L3 | LAKSHMI ASSOCIATES L1 | DIVYA ASSOCIATES L2 |
|---|---|---|---|---|---|---|
| 1.00 | Demolition of Concrete (un reinforced)in ground floor and pavings n exc 15 cm all as specified and directed | 24 | Cum | 250 ₹6,000 | 200 ₹4,800 | 300 ₹7,200 |
| 2.00 | M&L Demolition of cement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete. | 1.5 | Cum | 250 ₹375 | 300 ₹450 | 3,000 ₹4,500 |
| 3.00 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. | 5 | Qtl | 500 ₹2,500 | 300 ₹1,500 | 600 ₹3,000 |
| 4.00 | Dismantling of asbestos cement (corrugated, semi-corrugated etc) sheet in roof covering complete all as specified and directed. | 30 | Sqm | 65 ₹1,950 | 10 ₹300 | 30 ₹900 |
| 5.00 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. | 5 | Cum | 250 ₹1,250 | 200 ₹1,000 | 500 ₹2,500 |
| 6.00 | Demolition and breaking up drain pipes, 100 mm dia, (salt glazed ware, AC or reinforced concrete) set in cement mortar. | 30 | RM | 50 ₹1,500 | 20 ₹600 | 40 ₹1,200 |
| 7.00 | M&L Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) avg. 25 mm thick in levelling course for laying floor finish complete. | 153 | Sqm | 200 ₹30,600 | 250 ₹38,250 | 180 ₹27,540 |
| 8.00 | M&L for reinforced cement concrete (nominal mix), type B-1, 1:2:4, using 20 mm graded stone aggregate as in slab supported on wall, beam and columns in floor, roofs, landing, balconies, canopies, deck slab and in shelves and the like complete all as specified and directed. | 1.5 | Cum | 5,900 ₹8,850 | 5,000 ₹7,500 | 7,800 ₹11,700 |
| 9.00 | M&L for use and waste of form work, for to soffits of suspended slabs such as roof slab, floor slab, landings and similar work not exceeding 200 mm thick complete all as specified andirected. | 16 | Sqm | 350 ₹5,600 | 600 ₹9,600 | 390 ₹6,240 |
| 10.00 | M&L for providing and injectng chemical emulsion for post construction anti-termite treatment along the external wall below concrete or masonry apron using chemical emulstion @ 2.25 litres per linear metre including drilling and plugging holes etc in appron complete all as specified and directed. | 100 | RM | 150 ₹15,000 | 80 ₹8,000 | 90 ₹9,000 |
Updated dates
Tender Value
₹63.5 L
EMD Value
₹1.2 L
Closing Date
25 Dec 2025, 6:00 pmClosed
CWE (AF) JODHPUR
HQ CWE AF Jodhpur Opposite Mausam Vibhag Airforce Chauraha Ratanada Jaodhpur (Raj)-342011
SPECIAL REPAIR AND STRUCTURAL REHABILITATION OF BLDG NO P-2 AND P-2A AT TECH AREA AT AFS JAIPUR
2025_MES_729756_2
89095/E8
Open Tender
Civil Works
270 days
AGE (I) AF JAIPUR
as per NIT
8 documents required · 8 mandatory
₹1,000
AGE (I) AF Jaipur
₹1.2 L
Yes
6 Feb 2026
4 Dec 2025
27 Dec 2025
4 Dec 2025
25 Dec 2025
11 Dec 2025
Amount
Demolition of Concrete (un reinforced)in ground floor and pavings n exc 15 cm all as specified and directed
M&L Demolition of cement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete.
Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.
Dismantling of asbestos cement (corrugated, semi-corrugated etc) sheet in roof covering complete all as specified and directed.
Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.
Demolition and breaking up drain pipes, 100 mm dia, (salt glazed ware, AC or reinforced concrete) set in cement mortar.
M&L Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) avg. 25 mm thick in levelling course for laying floor finish complete.
M&L for reinforced cement concrete (nominal mix), type B-1, 1:2:4, using 20 mm graded stone aggregate as in slab supported on wall, beam and columns in floor, roofs, landing, balconies, canopies, deck slab and in shelves and the like complete all as specified and directed.
M&L for use and waste of form work, for to soffits of suspended slabs such as roof slab, floor slab, landings and similar work not exceeding 200 mm thick complete all as specified andirected.
M&L for providing and injectng chemical emulsion for post construction anti-termite treatment along the external wall below concrete or masonry apron using chemical emulstion @ 2.25 litres per linear metre including drilling and plugging holes etc in appron complete all as specified and directed.
M&L for providing and injectng chemical emulsion for post construction anti-termite treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm appart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and directed.
Dismantling of stone slabs and tiles of any description or thickness in floors approns etc, laid dry and pointed in any mortar complete all as specified and directed.
Dismantling floor, hearth or wall tilling and kota stones including cement mortar bedding (bur not backing), removing rubbish off the premises complete all as specified and directed.
M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc.0.11 sqm but not exc 0.18 Sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.
M & L for glazed ceramic coloured tiles in vertical surfaces 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with over and including rendering 10 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces for backing coat of tiles complete all as specified and directed.
M&L for light shade Ceramic tiles 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exc 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.
M&L for light shade Ceramic tiles 7 to 8 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.
M&L for 20 mm thick granite stone slab (table rubbed and polished) as on shelves/cooking plateform/pillars/riser over and including screed bed 20 mm thick in CM (1:4) set jointed in neat cement slurry and pointed in white/coloured cement to match the shade including grinding and polishing complete all as specified and directed.
M&L for 20 mm thick granite stone slab (table rubbed and polished) as on skirting/dado/steps over and including cement plaster 10 mm thick in cm (1:4) set jointed in neat cement slurry and pointed in white/coloured cement to match the shade including grinding and polishing complete all as specified and directed.
M&L for 20-25 mm thick, machine cut kota stone slab flooring 20-25 mm thick over and including 20 mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to math the shade of the slab including rubbing and polishing complete all as specified and directed.
M&L for grinding, rubbing and mirror polishing of existing kota stone floor and skirting complete all as specified and directed.
Taking down Chowkatts or frames n exc 1.5 sq m each with shutters (without taking off shutters form the frames) complete all as specified and directed
Taking down Chowkatts or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as specified and directed
S&F powder coated aluminium (minimum thicknessof powder coating 50 micron) work for doors, windows, ventilators, fixed/sliding (upto three track) including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for seperately) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS-733 and IS-1285, fixing with dash fasterners of required dia and size including necessary filling up the gaps at junction i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/peneling, CP brass/stainless screws all complete as per architectural drawings and the direction of Engineer-in-Charge.
S&F anodized aluminium grill (anodized transparent or dyed to required shade accoring to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with CP brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening szie for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, complete all as specified and directed.
S&F for 5mm thick sheet glass, ordinary quality, exc 0.50 Sqm in each pane, glazing with beads fixed with metal panel pins complete all as specified and directed.
S&F Eco 2000 series, window fabricated from roll formed section made of galvanized steel colour coated/powder coated (base steel as per IS-513D quality, galvanized as per IS 227 with zinc of 120 grams/Sqm) with total coated thickness of 0.60 mm. Coated section should be with primer coated of epoxy primer of 5-7 micron thick, finish painted with polyester paint of 12-16 microns thick and back coated with alkyd backers of 5-7 micron or powder coated with pure polyester powder up to 50-60 microns thick with the following details :- Dimension of Section : Section for outer frame shall be 72 mm x 55 mm, section for mullion 72 mm x 50 mm , section for glazed shutter frame of 52 mm x 25 mm and section for fixed glass bead should be of 12 mm x 12 mm with 4/5 mm plain float glass. Section for wire Mesh shutter shall be of 20 x 40 mm with stainless steel wire mesh of 0.36 mm dia of wire and 1.40 mm aperture. Fixing details : Frame and shutter sections should be cut to length and meter jointed with plypropyle corner bracket. Mullion section should be jointed with frame/mullion as using Nylon Mullion Cap. EthylPropylene Diamine Monomer (EPDM) Gasket shuld be used all around glass in shutter. Accessories : Each glazed shutter should be provided with SS Pivon hingees-1 Set, Seccolor Handle & Seccolor Stay. Grill : Window should be provided with Grill made of 10 mm MS Square Bar welded to 150 mm center to center to 6 mm x 12 mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws. Window frame shuld be fixed to brick/concrete masonry by using Nylon self expanding caps and driving MS electroplated 80 mm long screws into the caps through frame. Note :- (i) Cost of all fitting such as hinges, tower bolts, locking arrangement etc required for windows shall be included in rates quated by the contractor. (ii) Two Nos of Glass shutter and two Nos of mire mesh shutter shall be provided in each window. Cost of shutters, glass and wire mesh shall be included in rates quoted by the Contractor. (iii) Cost of Powder coated MS grill shall be included in rates quoted by the contractor. (iv) Net opening shall be measured for payment purpose.
M&L for cutting opening through old stone masonry walls, built in cement mortar for door, window and other opening, etc or cutting out defective masonry for underpinning including providing fixing and removing shoring, cleaning and stacking stone and removing surpulus to store and rubbihs off the premisses complete all as specified and directed.
M&L forming jambs etc to opening (to foregoing item) with stone including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work in cement mortar 1:4 complete all as specified and directed.
M&L for cutting into old stone masonry, built in cement mortar to form toothings for and bonding new brick or stone work including making good in cement mortar complete all as specified and directed.
S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing confirming toFe 410-W (Gde E- 250) quality A and ISI Marked complete all as specified and directed.
S&F for Framed work as grills, gratings etc ends of bars, shouldered and or riveted or forged in spikers, frame guard bars barred iron, doors, ladders, framed ballusters, walk ways, railling, frame work of water tanks and similar work confirming to Fe-290 Gde-E-165 complete all as specified and directed.
Supply and fixing for 3.15 mm dia, expended, welded, mild stee wire fabric of mesh, size 25 mm x 25 mm, weight not exc 4 kg per Sqm, including cutting in any size, fixed to steel member such as angle/flat with welding complete all specified and directed.
S&F 35 mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed..
S&F 35 mm thick 2nd class HW, glazed and skeleton shutters, open rebated & prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, gauze etc complete all as specified and directed.
S&F galvanised stainless steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned teaks galvanised wire staples fixed all as specified
S&F butt hinges medium weight cold rolled mild steel 100 mm long, complete all as specified and directed.
S&F stainless steel handles each 150 mm long complete.
S&F stainless steel barrel tower bolt 150 mm size complete.
S&F Stainless steel sliding door bolts, size 300 mm plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolt and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.
S&F Stainless steel sliding door bolts, size 250 mm plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolt and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.
S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, 150 mm long fixed in floor complete all as specified and directed.
M&L preparation of new wooden surfaces of any description, over 10 cm in width or girth, applying two coats of synthetic enamel paint over and including a coat of pink primer complete.
S&F 18 mm thick HDHMR board exterior grade including 1 mm thick aclylic high gloss shed over HDHMR both side laminated, antifungal, moisture registant and anit borer as per IS-14587 for frame and shutter for kitchen cabinet/cup board etc complete all as specified and directed.
M&L preparation of old wooden surfaces of any description, over and including 10 cm in width or girth, applying two coats synthetic enamel paint over and including a coat of pink primer complete all as specified and as directed.
Taking up or down steel tubing and connections including cleaning for refixing or removal to store in 15mm bore.
Taking up or down steel tubing and connections including cleaning for refixing or removal to store in 20 mm bore.
S & F of 15 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.
S & F of 20 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.
S&F in repair PVC connection pipe 15mm size with PTMT nuts of length 450mm etc all as specified.
S & F in repairs vitreous china wash basin white, flat back or angle back type, size 550 X 400 mm excluding taps, chain and plug but including waste pipe, brackets, cutting for and pinning in as required complete all as specified and directed.
S & F in repair Tubular towel rail, brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flange complete all as specified and directed.
S & F 32mm cromium plated cast copper alloy waste coupling (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) for wash hand basin all complete ad as directed
S & F in repair vitreous china wash down water closet pan (Pedestal pattern) white EWC floor mounted with PVC seat cover including fixing bolts and making connection to flushing cistern, including 100mm dia trap etc. complete all as specified and directed.
S&F in repairs vitreous china squatting pan 'Orissa' pattern, size 580 x 440 mm, white with integral foot rest, including connection to trap and to flushing pipe, anti-syphonic pipe etc and including trap set in and including concrete, complete making good to floorexcluding fulshing cistern and flush pipe complete all as specified and directed.
S&F in repairs vitreous china urinal flat back size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe including providing and fixing plug, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with bracket, flush pipe, grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.
S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia and 80 cm long, for low level flushing cistern complete all as specified and directed.
M&L in repair PVC low level flushing cistern 10 Ltr capacity white complete with inlet ball valve float , syphon assembly and dual flush button and brackets etc. complete.
S & F PVC single door bathroom cabinet contains 4 shelve with 5 mm thick mirror- any colour and size of 25.40 x 10.20 x 35.6 cm dimension complete all as specified and as directed by Engr-in-Charge.
S&F in repairs 15 mm long body bib taps fancy type cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.
S&F in repair 15 mm concealed CP stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.
S&F in repairs 15 mm two-way bore bib taps chromium plated cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.
S&F in repair health faucet (ABS Body) cast copper alloy chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible SS tube and ABS wall hooks including making connections and fixed in position complete in all respect as specified and directed.
S&F in repair mixer Pillar taps 15 mm bore fancy type, swan neck, long body, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.
S&F Brass CP wall mixer three way for mixing hot & cold water screwed down for iron pipe including provision for head and hand shower including 100mm dia hand shower with 1.0m long flexible SS pipe of 15mm dia and fixed complete all as directed
S & F in repairs Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to 15mm dia steel pipe or union all complete as directed
S & F in repair stainless steel Soap dish, approximate size 160x 160x90mm any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engr-in-Charge
S&F in repair grating 100 mm dia stainless steel (Min Wt 25 gms) complete all as specified and as directed.
S&F Cast iron floor trap 75 mm , with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.
S&F Cast iron soil, waste and vent spun pipes 75mm , in any length with or without ears with cement joints, laid in trenches or in floors all as directed and specified.
S&F Cast iron soil, waste and vent spun pipes 100mm , in any length with or without ears with cement joints, laid in trenches or in floors all as specified and directed.
S&F in repair cast iron soil, waste and vent spun pipes 100 mm bore in any length with or without ears with cement joints fixed to walls all as specified and directed.
S&F in repairs spun cast iron 100mm bore bends etc all as specified
S&F in repairs spun cast iron 75mm bore bends etc all as specified
S&F PVC (SWR) pipe, 110 mm bore, single sockete in any length, with rubber ring joints including fittings such as bend tee etc fixed to walls complete all as specified and directe.
M&L for Dismantling water tanks Exc 250 & n exc 500 ltrs capacity and removing from site complete all as specified and as directed.
S&F 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layer white in colour hoisted and fixed in position complete all as specified and directed.
M&L Ball valves 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms/ 50mm-1240 gms) all as specified and directed.
S & F in repair 20 mm bore size Stop valves, cast copper alloy chromium plated screwed down high presure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.
Supply only liquid water proofing compound.
M&L Cement concrete tiles 25 cm x 25 cm x 22 mm thick , machine pressed with grey cement and no pigment, set, jointed and pointed in neat cement slurry in floors, and cut and polished with floor finish including 20 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.
M&L for Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6 m mean radius, in half brick wall, built in CM 1:4 complete all as specified and directed.
M & L for rendering 15 mm thick in cement plaster in CM (1:4) on fair faces of brick or concrete surfaces complete all as specified and directed.
Taking down cement plastering on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.
M&L 10 mm thick rendering on other than fair faces of stone work in CM 1:6 as inner layer and 5 mm thick rendering in CM 1:4 finish even and smooth (without using extra cement) mixed with liequid WPC as directed by Engr-in-Charge on external surfaces all as specified and directed. Note : WPC will be measured and paid seperately against respective item.
M & L for rendering 15 mm thick in cement plaster in CM (1:6) on fair faces of stone surfaces, finish even and smooth without using extra cement complete all as specified and directed.
M&L 10 mm thick rendering in CM 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.
M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.
M & L for preparation of newly plastered previously untreated surfaces of walls and applying two coats of distemper oil emulsion over and including a coat of average 2 mm thick wall care putty and one coat of primer complete all as specified and directed.
M&L for preparation of newly plastered surfaces of wall and applying 2 mm thick water proofing wall care putty and applying two coats of 100% premium acylic emulsion exetirior paint (Camouflage pattern) having VOC less than 50 gms/litre and UV resistance as per IS 15489:2004, alkaly & fungal registance, dirt resistance exteriour paint of required shade (company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surfaces in camouflage pattern complete all as specified and directed.
S&F 20 mm dia brass chromium plated curtain rod complete all as specified.
S&F brass chromium plated bracket, fancy type for 20 mm dia tubular curtain rod complete all as specified and directed.
S&F angle iron or any section of any size, cut to any length as in hip and jack rafter, making of frame for sun shed or similar work, including cutting welding, joint to each other and inserting in wall complete all as specified and directed.
M&L for cutting stone, concrete wall, chases, pinning in, making good to facing where required and making good in cement mortar 1:3 or cement concrete type B-1, 1:2:4 (using 12.5 graded stone aggregate) to ends or edges of landing, steps, cills, sunshed, shelves, lintels and for inserting the sheet in wall etc and cutting chases for concealed water tubing or concealed conduit wiring et and making good, cutting exceeding 20 cm girth complete all as specified and directed.
M&L preparation of steel surfaces and applying two coats of synthetic enamel paint exceeding 10 cm width or girth over and including a coat of red oxide primer complete all as specified and directed.
M&L Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strenght of 550 Mpa as in roof coverng/cladding to wall/sun shade, fixed with self tapping screws complete all as specified and directed.
Providing & fixing false ceiling with fully perforated 12 mm thick micro tegular eged or 10 mm thic square edgd GRG false ceiling all heights with GRG (Glass fibre reinforced Gypsum) false ceiling tiles of size 595 x 595 of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO 0.5 to 0.75 as per IS 8225 : 1987, Noncombustible (Fire resistant/retardant) as per BS-476 (Part4)-1970, fire resistant/retardant and light relectance of 85% (minimum) to be laid in true horizontal level suspended on and including interlocking metal T-Grid of hot dipped galvanized iron section 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main 'T' runners of size 15 x 32 mm of length 3000 mm, cross-T of size 15 x 32 mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per Sqm) i.e 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully thread hanger rod upto 1000 mm length and L-shape level adjuster of size 85 x 25 x 2 mm, galvanized iron parimeter wall angle of size 24 x 24 x 0.40 mm of length 3000 mm to fixed on periphery wall/partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawings and as per directions of Engineer-in-Charge.
M&L for 75 mm thick plain cement concrete type C-2, 1:3:6, using 40 mm graded stone aggregate as in plinth protection or similar work, concrete finish even and smooth with using extra cement complete all as specified and directed.
M&L for 75 mm thick plain cement concrete type C-2, 1:3:6, using 40 mm graded stone aggregate for sub base complete all as specified and directed.
M&L for providing and laying 60 mm thick factory made chamfered edge coloured cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawn, drive ways or light traffic parking etc, of required strenth, thickness & size shape mady by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory, filling the joints with sand and cutting of pver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.
M&L for plain cement concrete, type B-1 1:2:4 using 20 mm graded stone aggregate as in roof kerbs or mud stop, rounded or chamfered on edges as in edges of inter locking paver blocks complete all as specified and directed.
Excavation in trenches. exc 1.5m wide and n exc 1.5m depth for foundation etc or for shaft wells, cesspits, manhole, pier etc n exc 1.5 m in depth and getting out in hard rock.
All as per item No 103 here-in-before but depth exc 1.5 mtr and n.exc 3.00 m.
S & F 150 mm bore, Reinforced concrete pipes, class NP-2, laid and jointed with cement mortar (1:2) with jute and rubber ring complete with collars, complete all as specified and as directed.
M&L cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested as specified.
M&L for Cutting into existing manholes for connecting new drain of 150 mm dia and over, making good to pipes and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1, smooth finished, and reforming benching as required, complete all as specified and as directed.
M&L for precast reinforcement cement concrete (nominal mix), type B-1, 1:2:4 (20 mm graded stone aggregate) as in man hole cover/shelves or similar work including form work complete all as specified and directed.
M&L for TMT bar 10 mm dia and over cuto to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and bing with and including mild steel wire (annealed) not less than 0.9 mm dia or secring with clips complete all as specified and directed.
M&L for PCC 1:4:8 type D-2, using 40 mm graded stone aggregate as in foundation and mass concrete.
Material and labour for Brick work with sub class 'B' bricks, Straight or curved on plan exc. 6 m mean radius built in CM 1:6, complete all as specified and directed.
M & L for rendering 15 mm thick in cement plaster in CM (1:4) on fair faces of brick or concrete surfaces, finish even and smooth without using extra cement complete all as specified and directed.
M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds,/stopped ends etc complete all as specified and directed.
Returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 cm.
Removing excavated material to a distance exc 250 m and n.exc 500 m complete all as specified and directed.
M&L for Relieving Structural members such as column, beam and slabs of their superimposed loads partially or fully by provision of adjustable steel props, frames etc. including providing necessary timber runners, bracing, jacking up arrangement all Complete to the satisfaction of Engineer in charge (Removing and redoing of brick work, if required, shall be paid separately.
M&L for Chipping off existing loose, damaged Concrete from RCC members of all affected RCC Columns, Beams, Slabs and Chajjas on External and internal facades, etc beyond main r/f. (if required in the opinion of the Consultant), carefully with chisel and hammer Providing and applying ‘Rusticide SS’ Rust passivator or equivalent as specified in the Brand Names to existing r/f. bars Including wire brushing of reinforcement , cleaning washing of concrete etc complete as directed.Providing and applying two coats of rust preventor slurry made out of “Polyalk Fixoprime” or equivalent as specified in the Brand Names and cement in proportion 1:1.5 to existing r/f.bars as directed complete. Providing and applying bonding coat of slurry made out of “Polyalk EP” or equivalent as specified in the Brand Names and cement in proportion 1:1 to concrete and r/f substrates complete as directedProviding and applying “Polyalk EP” or equivalent as specified in the Brand Names.Polymer modified cement mortar in Required proportions(1:5:15) to RCC members Including Hand packing, curing and making the surface rough for plastering. (Rates to include treatment cost for average thickness upto 25mm)
FILLING AND REINSTATING OF SEPARATION CRACKS Opening the Separation Cracks at the Junction of RCC and Masonry where ever directed and instructed into ‘’V’’ Grooves 2’’ to 3’’ from the either side of the cracks by carefully marking the areas to be opened up using a Cutting machine and skillfully /carefully Chiseling with a well sharpened chisel and hammer as directed including Wire brushing and washing of concrete Substrata and masonry walls with water jet to the surfaces thus prepared to the entire satisfaction of the Consultant as instructed and directed.
M&L for Moistening the Cracks, Providing and applying priming/bonding coat of slurry made out of “Polyalk EP”and cement (or equivalent as specified in the List of Brand names) in proportion 1:1 to surfaces prepared as instructed and directed. Filling the Cracks /Grooves by Providing and applying “Polyalk EP” Polymer modified cement mortar (or equivalent as specified in the List of Brand names) in Proportion of 1: 5: 15 (Polyalk EP: Cement: Graded sand/quartz sand) on the prepared surfaces and finishing it in level with the existing plaster Including Hand packing, curing and making the surface similar to the external plastering using wooden floats/punch etc. complete as per specified and directed.
M&L for Drilling holes of required size upto 16 mm Diameter and up to 50mm depth in concrete and cleaning the same as directed.
M&L for Providing and fixing 12 mm diameter aluminum /PVC injection nipples and securing the same as directed & Providing and injecting cementitious grout using CEBEX-112 additive of ‘Fosroc’ orequivalent make at the rate of 225 grams per bag of cement and using suitable mechanical gun/pump including mixing etc complete.
M&L for Providing & fixing epoxy dipped shear keys of 10mm dia and 4" to 6" length in columns before jacketing, Micro concreting as per Consultants Instructions and directions.
M&L for Providing, cutting, bending and fixing Additional Reinforcement in position steel reinforcement of specified/required sizes and shapes of any dia in the form or main rebars, stirrups & rings, distribution rebars etc., and tying them to shear connectors using GI binding wire. The additional rebars should be coated with TWO coats of Anti Corrosive protective coating & dry sand to be sprinkled on second coat including tying with Annealed Binding wires, providing cover blocks of appropriate sizes etc complete as specified and instructed by the Consultants.
M&L for Providing and laying Super fluid Microconcrete of minimum (M- 40 grade) -Roffe crete repairs (or equivalent as specified in the List of Brand names) in beam bottoms, columns, slabs etc. including mixing with 5mm to 10mm size aggregates, waterproof ply wood/ steel plate shuttering, pouring, temping, Consolidating, curing etc complete as per Manufacturer’s specification and Consultants Instructions.The item shall be paid on actual consumption of Micro concrete. Rate of this item shall include chipping of concrete, surface preparation, rust removal and prevention treatment as per specs and in accordance with consultants suggestions and directionsThe item shall be paid on actual consumption of Micro concrete.
M&L for EPOXY GROUTING: Providing, injecting and grouting High molecular weight Super Low Viscous (3 to 5 cps) 0.56 Kg/cm2 Epoxy Thermoset Resin Monopol (Krishna Conchem or equivalent) for Slab/Beams/Columns in appropriate proportion as per manufacturer’s specifications into cracks / honeycomb area of concrete including drilling minimum 50 mm deep holes of required dia. in concrete, fixing nipples 8 / 10mm dia., injecting grout by suitable gun / pump at 1.0 to 2.0 Kg/cm2 pressure and subsequent cutting / removal of the nipples and sealing of the hole and groove after completion of grouting with cement / epoxy mortar as directed by the Engineer in-charge.Rates to include searching the cracks, opening the same, fixing the nozzles & making all other provisions as per the manufacturer specification/ instructions to make the water tight structure only the affected area. Make:- Sunanda, Pidilite, Krishna Conchem, BASF, Fosroc
M&L Carefully Chiseling/ Chipping out all existing loose decayed Plaster of External Facades and Terrace area (need based areas) using Plaster Breaking machine and or Well sharpened Chisel & Hammers at proper angles carting away the Debris outside of bldg Premises etc complete as directed by the Consultants,Providing and applying 20/25 mm thk sand faced plaster to concrete members- brick work etc.of External wall facades using approved screened and Pre washed River sand including base coat of 13-15mm thick in C.M. 1:4 and curing the same for not less than three days and keeping the surface of base coat rough to receive the sand face treatment 6 to 8 mm thick of C. M 1:3 finishing the surface by taking out grains and curing for 7- 10 days, providing and mixing approved waterproofing compound in required quantities in both the coats complete. Note:- (i) From item No 116 to 126 for the structural rapair and strengthening and rehabilitation shall be applied by the company’s authorized applicator firm only. (ii) Contractor have to get prior approval of applicator or authorized agency by submitting its authorization letter to this office for approval prior to commencement of work. Department will conduct an official verification from manufacturer of its authorised agency. (iii) Submission of 10 year warranty certificate for structural repair and roof waterproofing treatment work over roof is mandatory after completion of work. (iv) The cost of Scaffolding work required at certain places is including in the respective items catered for repairs itself. No extra shall be paid for the same.
M&L for Chipping out all existing loose and decayed internal plaster and redoing the same with 15mm thk. Cement plaster in CM (1:4) finishing with ‘Instant Neeru’ of Elephant Brand or equivalent in the inside areas of staircase areas and over Internal Structural Members of premises, etc .
M&L for Removing and demolishing the existing waterproofing upto slab level of any thickness, stacking the excavated debris on the ground floor, in the compound of the building carting away the same outside the MES premises.
M&L for providing, 40 mm thick (average) plain cement concret, type-B-0, 1:2:4 (using 12.5 mm graded stone aggregate as in roof pading, concrete finish even and smooth with using extra cement and using liquid WPC as directed by Engr-in-Charge complete all as specified and directed. Note : WPC will be measured and paid seperately against respective item.
S & F APP based polymeric water proofing membrane of weight not less than 3kg/sqm, fix with torch application method, overlap while torching shall be 100 mm on length side and 100 mm on the width side, over a coat of bitumen 85/25 @ 1.20 Kg/sqm over a coat of bituminous primer @0.30 liter/sqm complete all as specified and directed.
M&L for Carefully Chiseling/Chipping out existing cracked /damaged IPS and Providing I.P.S. Finish over Chajja Tops etc laying Brick bats/ Metal pieces to the desired thickness and slope finished with cement mortar plaster of specified and required thk. in CM (1:4), with neat cement slurry including waterproofing compound, curing etc including making junction wattas etc complete as specified and directed.
M&L for Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure with cement mortar 1:6 (1 cement : 6 coarse sand)
M&L for Providing and laying in position plain cement concrete of specified grade cement with /granite/quartzite/gneiss metal mixing in concrete mixer including bailing out water,compacting, finishing surface, curing and including the cost of centering and shuttering at all level Nominal Mix of 1:1:2 (1 Cement OPC: 1 Carse sand : 2 graded stone aggregate 20 mm nominal size
M&L for providing damp proof layer in two coats of aclylic polymer coating consisting of 1 part of acrylic polymer liquid mixed with 2 parts of cementious powder applying at the rate of 1.40 Sqm/Kg mix per coat. Second coat should be applied after 4 to 6 hrs of first coat, 5 days curing is to be carried out to the surface before providing plastering. Note : Make of the material "Smart Care Damp Block 2K" of Asian Paints or equivalent from Dr Fixit, STP, CICA etc as approved
M&L for preparation of surface by scrapping any moisture or loose materials and applying the Water Proofing smart care solution as per manufacturer specification and allow the water proofing solution to dry completely for 8 hours before application of further surface finishes complete all as specified and directed.
Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc, removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.
Disconnecting unserviceable sub main wiring/service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed.
Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.
(b) One ceiling fan/exhaust fan point controlled by one, one way switch through regulator.
(c) One three pin 5 Amp socket on same board with other switches.
(d) One 3 pin 5 Amp socket on independent board.
S&F switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and directed.
S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed.
S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as specified & directed.
S&F socket out let 2 in 1,multipurpose 6 pin 15/16 Amp flush type ISI marked complete all, as specified & directed.
S&F ceiling fan regulator electronic flush , steped (four step) 230 Volts AC all as specified and directed.
S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified.
Supply and fixing LED light fitting 20W, 220V,AC with driver,including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.
Supply and fixing LED light fitting 10W, 220V,AC with driver,including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.
S&F LED Bldg security light high pressure die cast aluminium housing, IP 66, 25Watt, PF>0.95, Operating Voltage 120-270V AC, 50HZ including hot diped galvanised mounting bracket made to shape with and includinggalvanised clamps with bolts, nuts, washers and conductor to fitting with 3 core 1 sqmm PVC insulated copper cable from control box to fitting complete all as spd.complete all as spd and directed by Engineer-in-Charge.
Taking down existing ceiling fan/Exhaust Fan, dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan complete all as specified and directed.
S&F SPN DB Box, 12 way 12 Module, Double door, IP 54, Suitable for flush mounting and surface mounting with 100A Copper bus bar and fully shrouded neutral bar with door earthing and cable entry cover complete all as spd by Engr in Charge.
S&F TPN DB Box, 4 way 4 Module, Double door, IP 54, Suitable for flush mounting and surface mounting with 160A Copper bus bar and fully shrouded neutral bar with door earthing and cable entry cover complete all as spd by Engr in Charge.
Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP SP , in the MCB DB Complete with connection testing and commissioning
Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of SPN and current carrying capacity SPN 40 AMP, in the MCB DB Complete with connection testing and commissioning.
Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning of TPN 63 Amps
Taking down of Geyser of any capacity, cleaning the tank and refixing on wall complete all as spd and directed
S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole MCB, 20 Amp complete all as specified and directed.
M&L earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2020 incl dismantling of old unseviceable existing earthing complete all as specified and directed.
Supply and fix in repair Gun-metal, globe, or gate valves, 20 mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.
DIVYA ASSOCIATES (BID ID -3506706)
AMIT RISHABH BUILDERS PVT LTD (BID ID -3501147)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.28 MB
BOQ_831775.xls
BOQ • 0.41 MB
tender.pdf
Tender Documents • 4.81 MB
Download all tender documents and submit your bid