Coimbatore District Anaimalai town panchayat Focus Blocks Development Programme ( FBDP Scheme) 24-25

Amount

Earth work exception for foundation in all solids and sub-solids to full depth as may be directed except in hard rock requiring blasting but inclusive shoring, structing and baling out water wherever necessary and filling the sides of foundation with excavated earth in layer of not more than 15cm thick well rammed and consolidated and depositing the surplus earth in all places shown by the department officers with initial lead and lifts etc. including leaving the sites complete complying with standard specifications etc complete.

Plain cement cement 1:4:8 Mix using 40 mm ISS Gauge HBG Metal including cost and conveyance of all materials to the work site including all labour charges for mixing,laying,ramming,consolidation and curing etc., complete as per standard specifications.

Random rubble masonry in cement mortar 1:5 for foundation and basement using new stones including necessary provision for bond stones with simultaneous flush pointing with the same mortar above ground level complying with standard specifications.

Refilling in basement with excavated earth in layers of not more than 15cm thick well rammed and consolidated etc., complete

Brick Work in Cement Mortor 1:5 Mix (one cement, five sand) using new best II Class Bricks of size 9 ” x 4 3/8 “x 2 3/4 ” from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications - Up to Basement

Superstructure

Collection, supply and filling with well gravel including cost and conveyance of all materials and stacking them at road side to departmental gauge for pre-measurement including all labour charges for filling etc., complete as per standard specification. - Supplying and erecting in the position of centering for sides and soffits including necessary supports and strutting upto 3.00 m high for plain surfaces with all cross bracings using mild steel sheet of 90 mm x 60 cm and or suitable size stiffened with welded-mild steel angle of size 2mmx25mmx3 mm for boarding laid over silver oax (country wood) joists of size 10 x cm x 6.5 cm spaced at about 90 cm centre to centre and supported by casurina props 10 mm to 13 cm dia spaced at about 75 cm center to center etc. complete complying with standard specifications and as directed the departmental officers.

For Grade Beam

For Coloumn

For Slab

Supplying, Fabricating and placing in position mild steel or deformed steel bars for all reinforced cement concrete items of work including cost of steel transporting straightening cutting, bending, cranking binding welding etc. Including cost of binding wire MS.chairs laps to fix the reinforcement in all positions, all labour and materials complete complying with standard specifications and drawings and as directed by the departmental Engineers.- Reinforced cement concrete 1:1.5:3 (One cement one point five sand and three hard broken stone) using 20mm guage broken hard granite stone jelly for all RCC, items of works excluding cost of reinforcement and fabricating charges, centering and shuttering but including curing cost and conveyance of all materials to the site and all labour charges for mixing and providing fixture like fan clamps in the RCC floor or roof slabs wherever necessary as directed by the departmental officers etc., complete complying with standard specification.

A) Upto Basement

B) Above Basement

Weathering course concrete using best quality broken jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) over the RCC roof slab in the proportion of brick jelly to lime being 32:12.5 by volume and laid over in a single layer and consolidated to the required design and finished thickness, beating the concrete stantly wetted by sprinking lime jaggery water as per standard specification etc., complete as directed by the departmental officers.

Finishing the top of roof one course of machine pressed tiles of size 20cm x 20x2cm of approved quality laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound confirming to ISS by 2% weight of cement used and the joint pointed neatly to full depth of tiles with the same water proofing compound mixed with cement mortar, red oxide, etc., compete complying with standard specification.

Finishing the exposed surface of RCC item of work such as slabs beams sunshade panja canopy slab staircase waist slab leading slab etc., with cement mortar 1:3 (one cement and three sand) 10mm thick including baking the surface. The rate is too include the cost of providing the cement mortar beading of nosing for sunshades and staircase steps boulding slabs etc complete complying with standard specification.

Plastering with cement mortar 1:5 (one cement and five sand) 12mm thick in all floors including curing etc., complete complying with standard specification and as directed.

Supply and fixing of cuddapah slab 38/40mm thick including cost and conveyance of all labour charges etc complete.

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Dadooing walls with Glazed tiles of sizes 300mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Plastering with cement mortar 1:4 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309)

Painting the new walls two coats over one coat of priming with best Emulsion paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by the department officers etc., complete complying with standard specifications.

Painting two coat for new iron works ushing best synthetic enamal paint of approved branded quality of paint over existing primer coat, etc., complete complying with standard specification (The paint should be got approved by the departmental officers before use on works).

Manufacturing supplying and fixing of MILD STEEL Window made out of 40 x 40 x 6 mm M.S angle for outer frame, 35 X 35 X 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets ( 18 G ) with 5Nos,of stiffners using M.S.Flats of size 25 X 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase of Double shutters of 125 X 31 X 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 X 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers.

Manufacturing supplying and fixing of MILD STEEL DOOR made out of 50 x 50 x 6 mm M.S angle for outer frame,35 X 35 X 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets (18 G) with 5Nos, of stiffners using M.S.Flats of size 25 X 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase of Double shutters of 125 X 31 X 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 X 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers.

Supply and fixing of RCC Jolly including cost and conveyance of all materials to work site and labour charges etc., complete charges etc., complete.

Painting two coats over Block Board Paint with best approved best quality of synthetic enamel paint of approved colour over the existing priming coat etc., complete complying with standard specifications and as directed by the departmental officers.

Suppling and fixing of 1000 lit capacitty Priming Tank made up of PVC make Syntex/Equalant with necessary fitttings complying with all std specifications as directed.

Supplying and fixing in position colour glazed EUROPEAN WATER CLOSET with 'P' or 'S' trap and double flapped seat cover, 12.50 litres capacity P.V.C. low level FLUSHING TANK including all internal fittings fixed on C.I. brackets, 12mm PVC or brass nipple, chromium plated brown headed stopcock, 12mm nylon connection with necessary teakwood plugs, clamps, screws to the portion coming with walls and floors, including dismantling masonry and redoing the same to the original condition.

Supply and fixing in position 22" Indian type water closet with foot reset includes "P" (or) "S" trap including cost and conveyance of all materials to site and all labour charges etc., to complete as per std.,specifications.

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, sand cushion 100mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit(500V)32A neutral link and earth link(1"x1/8"copper flat)on TW plank of size 375mmx300mmx19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and interconnection with 7/20 PVC insulated copper wire from EBmeter to fuse unit with 1No 40Amp 30MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection(SD-125).

Finishing the top of flooring with granothatic flooring with cement concrete 1:2:4 (one cement, two sand and four aggrigate) using 6 to 12mm stone chips – 25mm tk etc., Complete.

Supply and run of 2 of 1.5 sq.mm (22/0.3) PVC Insulated SC unsheathed Cu. Conductor of 1100 V grade on 7/20 GI bearer wire for service connection mains (SD.64)

Supply and run of 2 x 1.5 Sq.mm (22/.3) PVC Insulated SC unsheathed CU. Conductor of 1100 Grade in 25mm Dia GI Pipe (Glass “B”) suitably Bent of both ends with necessary angle iron upright and end supports for Mains (SD 69).

Supply and fixing of single box type 4’40W flu. Fitting complete with tube copper choke and condenser with TW round blocks on wall orceiling with flu tube with PVC unsheathed copper leads from terminal to the fitting(SD. 88).

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb(SD.84)

Supply and fixing of 300mm (12") sweep (lightduty) AC exhaust fan complete with necessary wall opening and making good of the wall.SD(114)

Supply and fixing of 5A/15A 3pin combined flush type wall socket with 15A flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet.SD(141)

Wiring with 2x1.5sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5AFT switch and making good of the concealed portion with suitable colour for PVC concealed light / fan Point (for electronic regulator) (5 points per coil) (SD. 25).

Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,

K.RAJENDRAN (BID ID -1290086)

R.SIVALINGAM (BID ID -1290167)