GE 861 EWS-23 (T)/2025-26

Amount

Dismantling of CGI/PGI Sheet fixed with screws as in roof covering complete all as specified and directed by Engineer-in-Charge.

M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ Cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

M&L Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/Cladding to wall, Ridge and eaves board, fixed with self tapping screws as in specified complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm thick 2nd class softwood boarding planed one side with butt joint with nails in any situation complete all as specified and directed by Engineer-in-Charge.

M&L for 4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame complete all as specified and directed by Engineer-in-Charge.

M&L for 6mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in framed work complete all as specified and directed by Engineer-in-Charge.

M&L Clean Sawn Second class soft-wood timber framed in scantlings and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class soft wood plain fillets square rectangular or triangular in section wrought fixed with nails n exc 3 Sqcm bull nosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class soft wood plain fillets square rectangular or triangular in section wrought fixed with nails exc 3 Sqcm and n exc 6 Sqcm bull nosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed by Engineer-in-Charge.

S&F mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed by Engineer-in-Charge.

Taking down Shutters of any description n exc 1 sq. m each complete all as specified and directed by Engineer-in-Charge.

Taking down wooden frame not exceeding 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

S&F of solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with mild steel square tube as per specification and drawing given in clause 8.B.3 of SSR -2010 (Part-II Rates) complete all as specified and directed by Engineer-in-Charge.

S&F 30 mm thick Glazed and skeleton windows, ventilators, etc. provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b) as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkhats complete all as specified and directed by Engineer-in-Charge.

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (stiles) consisting of frame made out of mild steel tubes for top & bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement fixing in the frame at site as per specification , drawing complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified and directed by Engineer-in-Charge.

S&F 50 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (Unreinforced) in ground floor and paving n exc 15 cm thick blow or above ground level complete all as specified and directed by Engineer-in-Charge.

M&L for 25mm thick Cement concrete type B-0,1:2:4 (using 12.5mm graded crushed stone aggregate) complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick PCC 1:3:6 Type C-2 (using 40 mm graded crushed stone aggregate) as in sub-floor, sub-base, floor and pavings etc. complete all as specified and directed by Engineer-in-Charge.

M&L for 100 mm thick PCC 1:2:4 Type B-2 (using 40 mm graded crushed stone aggregate) as in floor and pavings and finishing the concrete even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Gde 'A' complete all as specified and directed by Engineer-in-Charge.

M&L for Plain Cement concrete type B-0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in coping complete all as specified and directed by Engineer-in-Charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick over and including 20mm cement screed base in cement mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

M&L for Non Skid joints free ceramic coloured tiles (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Coloured glazed joints free ceramic coloured tiles in vertical surfaces 350x 250x 7mm/ 450X 350X 7mm thick set over and including 10mm thick backing coat in cement mortar 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing 15mm bore and connections, including cleaning for refixing or removal from site complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing 20mm bore and connections, including cleaning for refixing or removal from site complete all as specified and directed by Engineer-in-Charge.

S&F medium grade GI tubes with all fitting and fixed complete to wall and ceiling or laid in floor 15 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F medium grade GI tubes with all fitting and fixed complete to wall and ceiling or laid in floor 20 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15mm Bib Taps with wall flange of chromium plated fancy type long shank screwed for Iron Pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stop valves/angle valves for 15 mm bore of pipe cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe, flush pipe and waste pipe) complete all as specified and directed by Engineer-in-Charge.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China wash down water closet (Squat pattern) white complete as fixed in repair (excluding flushing cistern and flush pipe) "Orissa" pattern size 580x440 with integral footrest inject connection to trap anti syphonage etc complete including joint between flushing pipe and socket of WC complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC valve less 10 litre capacity symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash basins, size 550x400mm white flat back including cutting for and pinning in ends of brackets or erecting stand including 32mm waste fittings, chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like laid over and including screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous counter sunk wash basins, size 550x400x250mm white including 32mm waste fittings, chromium plated with long screwed shanks & fly-nuts, flange fixed on granite slab/platform complete all as specified and directed by Engineer-in-Charge.

S&F in repairs PVC connection of 15 mm bore and 450 mm long with brass check nut and union etc complete as per cat No: EC-0106 aii as specified complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls etc including raking out joints, hacking for key, scrubbing down with water and removal of rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10 mm thick cement plaster in cement mortar (1:6) on brick work or concrete surfaces including finishing the surface even and smooth without usig extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick with WPC on external surfaces of brick work in cement mortar (1:4) including finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. Note : (WPC will be measured and paid separately)

Supply only Liquid water proofing compound complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old plastered surfaces of wall and applying one coat of cement base paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old plastered surfaces of wall and applying two coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint over coat of pink primer on wooden surfaces over 10cm width or girth including preparation on new surfaces complete all as specified and directed by Engineer-in-Charge.

M&L Preparation of old painted steel surface of any description, and applying a coat of synthetic enamel paint over 10cm in width or girth, not otherwise described complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-Charge.

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 Soft/loose cm complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type D2, 1:4:8 (using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L for brickwork with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius with old size bricks built in Cement Mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

S&F Mild Steel TMT bars 10mm and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clip complete all as specified and directed by Engineer-in-Charge.

M&L for providing RCC precast cement concrete type B-0 (1:2:4) (using 12.5 mm graded stone aggregate) as in cover slab for manhole and similar article with plain face set in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge. Note : Reinforcement shall be paid separately.

S&F 20mm bore gun metal glove or gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

Dismantling 500 Ltr capacity water tanks and removing from site and taking credit complete all as specified and directed by Engineer-in-Charge.

S&F 500 Ltr capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) 3 layer, hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

Dismantling 1000 Ltr capacity water tanks and removing from site and taking credit complete all as specified and directed by Engineer-in-Charge.

S&F 1000 Ltr capcity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) 3 layer, hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

S&F 20mm dia bore Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm outlet dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/wall or in floors complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/wall or in floors complete all as specified and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) bends any radius with access door complete all as specified and directed by Engineer-in-Charge.

S&F in repair 110mm bore PVC (SWR) junction (Single T) equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F in repair 75 mm bore PVC (SWR) junction (Single T) equal or unequal 75 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repair 110 mm bore PVC (SWR) vent cowl 110 mm bore complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge.

S&F 1.25mm thick steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: with push pull or manual type complete all as specified and directed by Engineer-in-Charge.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed by Engineer-in-Charge.

S&F Ball bearing for rolling shutters complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick Cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminium/copper point wiring (light fan socket or power) complete and making good disturbed surfaces of walls, floor to match with existing and keeping items aside in safe custody for reuse such as regulators, light fitting, MCBs complete all as specified and directed by Engineer-in-Charge.

M & L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS/ wooden sunk box of required size, & as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-89 here in above but for One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-89 here in above but for One 3 pin socket outlet, 5 Amps, on independent board, with cables 1.5 sq. mm size complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-89 here in above but for One 3 pin socket outlet, 15 Amps, on independent board, with cables 4 sq. mm size complete all as specified and directed by Engineer-in-Charge.

S&F in replacement switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified and directed by Engineer-in-Charge.

S&F in replacement switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal 240 volt complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Switch socket combination 2 in 1, 3 pin, 15 Amp flush type universal 240 volt complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in replacement Fan step regulator, 120W - 2 module type electronic fan regulator, duly ISI marked with and including connector complete all as specified and directed by Engineer-in-Charge.

Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified and directed by Engineer-in-Charge.

Supply & fixing lamp holder (Angular / Straight), insulated body, with back plate for batten fitting complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lamp 9 W complete all as specified and directed by Engineer-in-Charge.

S&F decorative ultra slim linear LED 20 Watt 4' long lighting fixture with extruded aluminium heat sink, environment friendly, energy efficient ready to use pack including LED tube complete with inbuilt electronic driver, PCB, connector block etc. including connecting up three core copper flexible cable from ceiling rose to fittings including connecting up and fixed on including two nos PVC square box of required size complete all as specified and directed by Engineer-in-Charge.

S&F LED Bldg security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete with including suitable wire 2.5 sqmm copper conductor from junction box to light fitting in non metallic PVC conduit complete all as specified and directed by Engineer-in-Charge.

S&F sheet metal enclosure Vertical type, Triple pole and neutral, AC, 415 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified and directed by Engineer-in-Charge.

Supply & fixing MCB, SPN (single pole and neutral), AC, 240 volts, B series capacity 32 Amps 10kA and making connections complete all as specified and directed by Engineer-in-Charge.

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm centre to centre both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing exhaust fan 300 mm sweep PVC body with louver, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and directed by Engineer-in-Charge.

Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. complete all as specified and directed by Engineer-in-Charge.

M & L for sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through and including PVC casing and capping with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC casing capping 25 mm size complete all as specified and directed by Engineer-in-Charge. Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core and one run of PVC casing and capping shall be measured as single run)

Supply and laying cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 2.0 core complete all as specified and directed by Engineer-in-Charge.

M/S ELITE ENVISION BUILDERS (BID ID -3478711)

M/S MUHIBULFUKARA ENTERPRISES (BID ID -3482302)

M/S Sheikh and Co (BID ID -3479634)

M/S NEW IQBAL ENTERPRISES (BID ID -3480410)

Asian Marketing Co (BID ID -3479529)

JANDOO AND CO (BID ID -3480407)

WUYAN ENGINEERING TECHNOLOGY (BID ID -3485284)

M/S SHAH RAOUF (BID ID -3479513)

Bidder Name

M/S GASSI BROTHERS