Renovation of Old Girls Hostel in the Campus of RINPAS Female Section at Kanke, Ranchi

Amount

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing R.C.C. M - 200 with nominal mix of (1:1.5:3) in roof slab with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Centering and shuttering including strutting, propping etc. and removal of form forWalls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

providing Tor steel reinforcement of 10mm,12mm,16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.(8mm dia )

(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

Taking down old door and window shutters including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down chaukhats in doors including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.

With "A" grade white 15X15cm Tiles.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar1:4 (1 Cement : 4 Coarse sand),jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete

Dismantlingtile work in floors and roofs laid in cement mortar including stacking material with in 50 metres lead for thickness of tiles 10mm to 25mm including all complete job as per direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 38mm , thick good quality well dressed and well seasoned sal wood 1/3rd glazed and 2/3 paneled shutter in doors and window with 25mm thick panels with one side plain and other side chamfered with aluminium fittings such as hinges, sliding doors boltes tower bolts handles or rings, hooks and eyes, cleats, sand blocks as per schedule and 3mm thick plain glass panes fitted with sal wood beads and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over old wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing &Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone patter with anti algae and Uv resistace properties to be aapplied as intermediate fiish in desired pattern @ 43.04 kg/s10 sqm to form film of 1-1.15mm thickess after scrapping and propperly cleanig the surace to remove loose particles from the plaster surface,followed by top coating with premium acrylic smooth exterior paint with silicoe additives of required shade by two or more cots @ 1.43 litre/10sqm,complete as the direction of E/I.

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer,over the plastered wall suface to prrepare the surface even and smooth complete.job as per direction of E/I.

Providing and fixing alumiunum work for door ,windows ,ventilators and partitions with extruded built up standard tubular sections, appropriate z sections and other sections of approved make conforming to IS:733 and IS:1285,fixed with dash fasteners of required dia and size including necessary filling up the gaps at junctions,i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight ,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling C.P. brass/stainless steel screws .all complete as per architectural drawings and the directions of Engineer-in-charge.Glazing and paneling to be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing & fixing glass panes with putty and glazing clips in steel doors,windows,clerestory windows all complete with: 5.50mm thick glass panes.

Providing and fixing fly proof wire gauze to windows,clearstory windows& doors with M.S.flat 15x3mm and nuts & bolts complete stainless steel (grade 304) wire gause of 0.5mm dia wire and 1.4 mm aperture on both sides including all complete job.as per direction of E/I.

Providing and fixing 18mm thick mirror polished, machine cut for kitchen platforms, vanity counters facials and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4(1 cement:4 coarse sand) with joints treated with white cement ,mixed with matching pigment, epoxy touch ups ,including rubbing, curing etc. complete at all levels.(Green marble)

Providing edge moulding to 18mm thick marble stone counters venities etc.including maching polishing to edge to give hight gloss finish etc complete as per design approved by E/I.Granite work

Providing and laying polished vitrified floor tiles in different sizes(Thickness to be specified by the manufacture) with water absorption’s less than 0.08% and conforming to IS:15622 of approved make in all colours and shades,laid on20mm thick cement mortar 1:4(1cement:4 coarse sand)@ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel,plier,wedge,clips of required thickness,leveling system and rubber mallet for placing the tiles gently and easily.Glsazed viterified floor tiles including all complete.(size 600x1200mm)

Supplying fitting and fixing M.S.Grill made of 20x6mm M.S.flat as per approved design and drawing properly fabricated with joints continous fillet welded and finished smooth carriage of grill to work site,hoisting as per building specification and direction of E/I(where materials to not supplied by the deptt)

Providing two coats of synthetic enamel paint over a coat of red oxidized paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.E/l.

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

(iv) 600X600 mm size

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Removal of old tarfelt and disposal of debris with all leads complete job as per direction of E/I.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing &Applyingpolymer modified,flexible cementatious negative side waterproofing coating with elastic water proofing polymers on interior wall plaster surface in three coats @ 14.35kg/10sqm,one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible,complate in all respect as per the direction o f Engineer-in-charge.

Providing and fixing double scaffolding system (cup lock type) on theexterior side, up to seven story height made with 40 mm dia M.S. tube 1.5m centre to centre, horizontal & vertical tubes joining with cup & locksystem with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircasesystem in the scaffolding for working platform etc. and maintaining it in aserviceable condition for the required duration as approved and removing itthere after .The scaffolding system shall be stiffened with bracings, runners,connection with the building etc wherever required for inspection of work atrequired locations with essential safety features for the workmen etc.complete as per directions and approval of Engineerin-charge .The elevationalarea of the scaffolding shall be measured for payment purpose.The payment will be made once irrespective of duration of scaffoldingThis item to be used for maintenance work judicially, necessarydeduction for scaffolding in the existing item to be done

Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(a) 580mm longwith 10.0 lit. low level P.V.C. cistern

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

S/F/F VIP Bath room fitting including all complete job as per direction of E/I.

Bib cock (Long tahread)

Angular stop cock

Mirror of 6mm thick 600x450mm

pillar cock long neck

wall mixer withtelephonic shower arrangement

Glass shelf 22"

soap dish

Towel Rail 24"

100 mm dia steel Jali

Providing and fixing Chlorinated polyvinyl chloride (CPVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e. fixing the pipe with clamps at 1.m.spacing.This included jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(Internal work)(Concealeld work)

20mm dianominal outer dia pipes

Providing and fixing Chlorinated polyvinyl chloride (PVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings..This included jointing of the pipes & fittings with one step CPVC solvent cement trencing,refilling & testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(External work)

25mm dianominal dia pipes

32mm dia

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion(i)single socketed pipes.

110mm diameter

75mm dia

Providing and fixing on wall face unplasticised PVC pipe clips moulded fittings, accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring confirming to I:5382 leaving 10mm gap for thermal expansion.

110mm dia

Providing and placing on terrace(at all floor levels) polyethylene water storage tank ISI 12701 marketed with cover and suitable locking arrangement and making necessary holes for inlet ,outlet and overflow pipes but without fillings and the base supported for tank.

Providing and fixing on wall face unplasticised PVC moulded fittings, accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring confirming to I:5382 leaving 10mm gap for thermal expansion.

Couplar 75mm dia

Coupler 110mm dia

Single pushfit coupler 75mm dia

Single pushfit coupler 110mm dia

Single Tee with door

75mm dia

shoe(plain)

75mm dia

110mm dia

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.

Easing and adjusting door and window shutters with chaukhats in old work complete as per specification and direction of E/I.

Carriage of materials from nearest approved sources of supply including loading into trucks and unloading from trucks and stacking properly at work site as directed by the E/I.

sand lead 8K.M.

chips lead 22K.M.

Brick lead 8K.M(1K+7P)

Stone Metal 20 km lead

Wiring for light/fan point/exhaust fan point/call bell Point with 1.5 sq.mm FRPVC insulated copper Conductor single core cable in surface/recessed PVC conduct with Modular type switchmodular plate, Suitable size G.I Box etc. as required.

Group A

Twin control point wiring in PVC conduit withModular type switch-wiring for Twin control light point with 1.5sqmm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit 2 way Moodular type switch,Modular plate,suitable size G.I.boax and earthing the point with 1.5 sqmm.FRPVC insulated copper conductor single core cable etc as required.

Wiring for circuit/submain wiring along with wiring with the following sizes PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5sqmm+1x1.5sqmm earth wire

2x2.5sqmm+1x2.5sqmm earth wire

2 x 4 sq mm +1 x 4 dsq mm earth wire

S/F Suitable size G.I.Box on surface/Recess with suitable size ofr phenolic laminated sheet cover in front including providing 3pin 5/6 Amp socket outlet and 5/6 amp. Piano type switch connection as painting etc. as req.

S/F Suitable size G.I.Box on surface/Recess with suitable size ofr phenolic laminated sheet cover in front including providing 6 pin 15/16 Amp socket outlet and 15/16 amp. Piano type switch connection as painting etc. as req.

Supplying and fiaxing suitable size G.I.box with modular plate cover in tahe front on surface or in recess including providing and fixing 15/16 amps sitch,connections painting etc as required( for AC)15/16amps,6pin socket outlet

Supplying and fiaxing suitable size G.I.box with modular plate cover in tahe front on surface or in recess including providing and fixing 15/16 amps sitch,connections painting etc as required( for AC)15/16 amps,one way switch

S/F”C” series SPMCB: supplying and fixing 6 amps to 32amps rating,240 volts ,10KA,"C" curve, ,miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections ,testing and commissioning etc as required.

6/32 amps , single pole

40 amps, TPN

50/63 amps TPN

S/F Modular type switch/socket supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connections but excluding modular plaate etc as reqd.

5/6 Amps 3pin 5/6 Amp socket

5/6 amps,3 socket outlet

sUPPLYING AND FIXING MODULAR BLAMKING PLATE ON THE EXISTING MODULAR PLATAE & SWITCH BOX EXCLUDING MODULAR PLATE AS REQUIRED.

Supplying and fixing the following way,horizontal type three pole and netural, steel M.C.B.ditrubutionbaord,415volts, on surface/recess, complete with tinned copper busbar, neutral bus bar, earth bar,din bar, interconnection powder painted including earthing etc as required ( butwithout MCB/RCCB/Insolator)

4way(4+12) Double door,Horizontal type

Supplying and drawing following sizes of FRPVC insulated copper conductor,single core cable in the existing surface/recessed steel/PVC conduit as required.

3x1.5 sqmm

Supplying anf dixing of following sizie of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/pvc conduit as required.

1 run of cable

2 run of cable

3 run of cable

Laying of one number PVC insulated and PVC sheathed/XLLPE power cable of 1.1KV grade of following size on wall surface as required.

Upto35sqmm (clamped with 1mm thick saddle)

Above 35 sqmm and upto 95 sqmm (clamped with MS flat clamp)

S.I.T.C of floowing rating recess/surface mounted LED round/square shape down light Luminarie with prfessurfe die cast housing for single phase supply voltaage .Luminarie shall be confirm to IS:10322 Part 5/section-2 or JEC:62722 with all neccssary accessories as required

18/20 W LED Round Down light

6/7 W LED Round Down light

Recess Mounting LED panel Light 2x2(36W) including all complete job as per direction of E/I.

Supply of wall mounted Fan 16"(400mm) including all complete job as per direction of E/I.make Bajaj/crompton/Havells.)

I.T.C of ceiling fan including wiring the down rods of standard length(up to30cm) with 1.5 sqmFRPVC with1.5sqmmFRPVCinsulated copper conductor single core cable etc as reqd.

Erection of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting complete with all accessoreis including connection etc as requried.

S/F 2 Pin 5 Amp ceiling rose on the existing junction Box wooden block incuidng connection etc as reqd

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

M/s Sanjay Kumar Dwivedi

Vidya Construction

Ravi Shankar Kumar Rai

M/S Raman Construction

Sanjay Kumar Pradhan

MUNMUN KUMAR