SPECIAL REPAIR TO BLDG NO P 25 (OTM ACCN) AT DEF AND EMP COY, HQ 10 RAPID (H) UNDER GE (SOUTH) AKHNOOR

Amount

Demolition of cement concrete (unreinforced) concrete in ground floors and paving n-exc 15cm thickness ( below or above ground floors.) , complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection joint filled with bitumen sand mixer, 50mm thick finished even and smooth without using extra cement complete all as specified and as directed by engineer in charge.

M&L cement concrete type B1 1:2:4 using 20mm graded stone aggregate 25mm thick as in flooring etc, complete all as specified and as directed.

M&L screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement 1:6, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises , complete all as specified and directed.

Rendering 10mm thick on fair faces of brick work or concrete surface in cm 1:4 as for tiles screed bed , complete all as specified and as directed.

M&L glazed ceramic coloured designer pattern tiles 450mmx 300mmx7mm thick on vertical surface such as skirt, Dado etc. set and jointed in white colour cement, complete all as specified and directed.

M&L non-skid ceramic coloured designer pattern tiles 400x400mmx7mm thick in floors etcset jointed in neat cement slurry and pointed in white cement or coloured cement to match etc, complete all as specified and as directed.

M&L for roughening surfaces of old concrete floor by picking,sweeping clean and wasining down with water to remove dust etc after that applying brushing neat cement slurry with 3.0 Kg of cement per Sqm and 15mm thick screed bed in cm 1:4 to receive to kota stone/floor tile

M&L for Machine cut kota stone slab flooring 20-25mm thick over and included cement screed base of 20mm thick cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Kota stone slab 16-18mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick cement mortar 1:4 rendering and jointed with jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete all as specified and as directed.

M&L for granite 20mm thick(table rubbed and polished) in cooking platform and like in cement mortar 1:4 including pointing in white cement(1:2) using marble dust making holes in RCC shelves suitable for gas pipe with round edges where required complete all as specified and as directed.

Demolition for cement conc exc 15cm thickness but above ground floor as sunken floor , complete all as specified and as directed .

M&L for laying water proofing treatment to sunken portion of WCs bathroom etc by applying cement slurrey mixed with Acrylic based polymer modified cementitious composite compound of makes as approved in technical Instruction 5/2003 :- (a) First layer of slurry cement @ 0.488 kg/ Sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/Sqm .The layer will be allowed to air cure for 4 hrs. (b) Second layer of slurry of cement @ 0.242 kg /Sqm mixed with Acrylic based polymer modifiedd cementitious composite compound @ 0.126 Kg/Sqm . The layer will be allowed to air cure for 4 hrs.

M&L for 15mm thick rendering in 1:3 CM with using 3% WPC as in sunken portion complete all as directed.

M&L for applying evenly a tack coat of industrial bituminous 85/25 @ 1.20 Kg per square mtr including cleaning surfaces, complete all as specified and as directed.

M&L cement concrete type B1 1:2:4 using 20mm graded stone aggregate 25mm thick as in flooring with using 3% WPC etc. ,complete all as specified and as directed.

M&L PCC 1:5:10 type E-2 using 40mm graded stone aggregates as filling under (sunken slab) floors, complete all as specified and as directed.

M&L for 40mm thick Plain Cement concrete type B0 1:2:4 using 12.50mm graded stone aggregate as in floor etc complete mixed with WPC @ 3% by weight of cement (WPC measured and paid separately) laid finished even and rough to receive plaster without using extra cement complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregates as sides of rounded or chamfered on edges of sunken floor complete all as specified and directed.

S&F 32mm dia G I pipe beveled cut at both ends by making hole in walls sunken portion approx above the R C C slab and ceiling finished the hole with cement plaster 1:2 to match with existing surfaces complete etc, complete all as specified and as directed.

M&L for repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derusting and cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but n.exc 3Kg/Sqm (if required) with or without facia and finished with cement mortar 1:3 using coarse sand and work in patches area n.exc 5 Sqm and thickness RCC member n.exc 70mm incl necessary formwork and applying two coats of finishes to match with the existing surfaces at any height complete. (note: welded mesh to be paid separately)

S&F for Hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement , complete all as specified and as directed by Engineer-In-Charge.

M&L for dismantaling of old /damaged existing roof treatment with concrete and cleaning all waste and dirt by wire mesh ,picking ,sweeping and washing down with water to remove dust etc and removal of all material out side the cantt area and applying one coat of neat cement slurry with 3.0 kg of cement per sqm on cleaned surfaces of roof evenly , and screed bed / rendering 10mm thick on fair faces of brick work opr concrete surfaces ,in cement morterr including mixing water proofing treatment on roof top, applying a coat of bituminious primer confirming to IS - 3344 @ 0.40kg/Sqm on the prepared surface,after the primed surface has dried , apply a coat of hot blown 85/25 penetration grade blown bitumen or equivalent viscosity grade blown bitumen ( Penetration of bitumen when tested as per IS 1203 will not be more than 40) conforming to IS 702 @1.20 kg/ Sqm ofthe surface. provide APP ( Atactic polypropylene ) modified polymeric five layered membrane with central core of 100 micron high molecular high density polyethylene film . Minimum weight of membrane will be 3kg /Sqm . Other proporties of APP modified water proofing membrane will be as laid down in MES SSR -I Part 11.43.2.2 . Product name - multiplus Mfg by M/S STP Texes Ltd Gurgaon / Hyper Plus Standard mfg by M/s IWL india Ltd Chennai/ Bengal Acquaflux- Mfg M/s Bengal Bitumen , New Delhi /Superior Polyplus 310 Mfg by STP Ltd or any other equivalent make approved by E-in-C Branch will be used . App membrane will be laid minimum end lap of 150 mm and side lap of 75 mm bonded with hot blown bitumen. Over the APP membrane apply semi hot blown 85/25 penetration grade bitumen or equivalent viscosity grade blown bitumen ( Penetration of bitumen when tested as per IS 1203 will not be more than 40) / conforming to iIS 702 @ 1.20 kg /Sqm and blinded with fine sand in dry condition @ 0.50 Kg/Sqm and applying two coats of aluminium paint, complete all as specified and as directed by Engineer-In-Charge.

Taking down or up steel tubing and connections including cleaning for re-fixing or removal to store 15mm bore , complete all as specified and directed.

Taking down or up steel tubing and connection s including cleaning for re-fixing or removal to store 20mm bore , complete all as specified and directed.

S&F for Tube 'medium grade' galvanized, with all fitting and fixed complete to walls and ceiling etc 15mm bore, complete all as specified and directed.

S&F for Tube 'medium grade' galvanized, with all fitting and fixed complete to walls and ceiling etc 20mm bore, complete all as specified and directed.

S&F Bib taps chromium plated fancy type, cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair 15mm bore , complete all as specified and directed.

S&F for wall mixer with provision of shower for mixing hot and cold water 3 in 1 fancy type brass chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed 15mm bore fixed.

S&F 15mm angular stop cock with wall flange stainless steel/Brass chromium plated,screwed down high pressure with or without lathered hot and cold with long screwed shanks and fly nuts complete all as specified and directed.

S&F for basin mixer, 2 in 1 , cast copper alloy, with capstan head chromium plated screwed down high pressure with or without lathered hot or cold with long screwed shanks and fly nuts screwed for iron pipe 15mm bore, complete all as specified and directed.

S&F for PVC connection 15mm bore size with PTMT nuts of length 45cm, complete all as specified and directed.

S&F as in repairs PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets. 10 ltr capacity, complete all as specified and directed.

WHB counter basin oval type Cat CNS WHT-WB03 or quivalent size 195x590x420mm make Jaguar including complete fittings and fixtures complete all as specified and directed .

S&F for fancy brass chromium plated shower rose 125mm fixed in repair , complete all as specified and directed.

Ball valve high pressure of PTMT with epoxy coated Aluminum rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed in repair 20mm bore, complete all as specified and directed.

S&F CP grating 150mm dia with centre hole , complete all as specified and directed.

Disconnecting existing tanks, capacity exceeding 500 liters but not exceeding 1000 liters setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position (cleaning repairing, etc. measured separately), complete all as specified and directed .

S&F Rotational moulded polythene water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 1000 ltr capacity incl dismantling water tanks and removing to store , complete all as specified and directed.

S&F for Gun-metal, globe or gate valves, for bore dia of pipe in mm with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Supply and fixing in repairs vitreous China squatting pattern Orissa pattern WC size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but including lime concrete bedding complete all as specified and as directed.

Supply and fixing vitreous China squatting pattern Orissa pattern WC size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but excluding lime concrete bedding complete all as specified and as directed.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flush pipe but excluding flushing cistern) and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making good to dismantled/ damaged floor all as specified.

S&F brass chromium plated tubular towel rail 20mm dia(D) type 60cm long between flanges complete.

S&F 32mm /40mm dia waste pipe for WHB,/urinals complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, complete all as specified and directed.

Taking down chokats or frames with shutters (without taking off shutters from frames) exceeding 1.5 Sqm but n.exc 4 Sqm each , complete all as specified and directed.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, size of frame 125x60mm, complete all as specified and as directed .

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 105x60mm, complete all as specified and as directed.

Plain cement concrete M-10(1:3:6), type C-0, (using 12.50mm graded crushed stone aggregate), nominal mix, as in cills, steps; plinth courses, string courses, lacing courses, copings, kneelers, apex stones, bed plates and in hold fasts or filling in hollow of steel frame, including necessary form work, complete all as specified and as directed.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing.

S&F for factory made steel Window, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter, jointed internally with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs, Galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and 3mm thick ordinary sheet glass pans with oil putty and clips etc, complete all as specified and as similar to shown in drawing No- CEUZ/TD-1517.15, sheet No- 1/3 to 3/3 and as directed by Engineer-In-Charge.

S&F for factory made steel ventilator, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter, jointed internally with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs, Galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and 3mm thick ordinary sheet glass pans with oil putty and clips etc, complete all as specified and as similar to shown in drawing No- CEUZ/TD-1517.15, sheet No- 1/3 to 3/3 and as directed by Engineer-In-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded etc. with suitable PVC sheet beading including hinges etc complete all as specified.

Factory made, 35 mm thick plain framed panelled shutter (two panel) of second class hard wood rail and style with lock rail and panel of 9 mm BWP commercial ply. The size of rail and style as per IS : 1003 Part I, klin seasoned and chemically pressure treated, all as specified and directed.

Glazed and Skelton shutters using 2nd class hard wood 35mm thick open rebated and prepare to receive glass or gauge etc edges of framing plain and chamfered or fitted cut or mitered beads for securing glass size of member of shutter as specified in SSR Part-I section 8, clause 8.23(a) and divided in square complete all as specified.

S&F for glavanised Mild steel wire cloth. 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvnaised wire staples, complete all as specified and directed.

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome primer, complete all as specified and as directed .

S&F aluminium anodised barrel tower bolt of extruded section and fixed, length of bolt 150mm, complete all as specified and directed.

S & F Aluminum alloy, anodized sliding door bolt with hasp staple( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolt of extruded section or cast aluminium alloy 250 mm long , complete all as specified and directed.

S&F extruded aluminum alloy handles 150mm size fabricated type anodized all as specified.

300mm ordinary rat rail rod pattern spring including roller plate complete fixing mild steel spring, complete all as specified and directed.

Floor doors stoppers of aluminium alloy body and tenque anodisede with hard drawn steel spring fixed in floor 150mm long, complete all as specified and directed.

S & F Butt hinges, medium weight cold rolled mild steel 100mm long to PVC Door etc, complete all as specified and directed.

S&F epoxy powder coated pelmet rods of mild steel 25 mm with and including pair of fancy type finnals complete fixed as in repair, complete all as specified and directed.

Demolition of brick built in cm including all quoins arches pillars etc, complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved in plane exc 6cm mean radius built in cm 1:6, complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

M&L 15mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth w/o using extra cement in cm1:6, complete all as specified and directed.

M&L 5mm thick plastering on fair faces for cone surfaces finished even and smooth w/o using extra cement in cm1:3 on ceiling , complete all as specified and directed.

M&L 15mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth w/o using extra cement in cm1:4, mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. (Note water proofing compound shall be measured and paid separately).

M&L for Preparation of new surface of wall and apply with 1 mm thick wall care putty, on plastered surfaces,preparatory to distempering and applying two coat of oil emulsion white or tinted on wall over one coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment and applying with 1 mm thick wall care putty, on plastered surfaces,preparatory to distempering and applying two coat of oil emulsion white or tinted on wall over one coat of primer , complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying by finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed by engineer in charge

M&L for complete removal of existing treatment of wall and applying by finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed by engineer in charge

M&L Preparing of new surface of plaster and applying three coats of white wash on ceiling completed all as specified and as directed.

M&L Preparing of old surface of plaster and applying two coats of white wash on ceiling completed all as specified and as directed.

Dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement motar and taking out from floors or walls complete all as specified and as directed by engineer in charge.

Dismantling of 75mm dia cast iron or reinforced concrete drain pipes, jointed in cement motar and taking out of trenches , if required complete all as specified and as directed by engineer in charge.

S&F for PVC (SWR) pipes110mm dia single socketed in any length with rubber ring joints fixed to walls

S&F for PVC (SWR) pipes75mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F for PVC (SWR) pipes75mm dia single socketed in any length with rubber ring joints fixed to walls

S&F PVC (SWR) bends 110mm dia any radius

S&F PVC (SWR) bends 75mm dia any radius

S&F PVC (SWR) branch piece110mm dia, single (single Y) equal or unequal

S&F PVC (SWR) branch piece75mm dia, single (single Y) equal or unequal

S&F PVC (SWR) branch piece110mm dia, double (double Y) equal or unequal

S&F PVC (SWR) 110mm dia junction double, (double T), equal or unequal with access door

S&F PVC (SWR) vent cowl 110mm dia

S&F PVC (SWR) vent cowl 75mm dia

S&F PVC (SWR) 'P’ trap 110mm dia

S&F PVC (SWR) 'S’ trap 110mm dia

S&F 150 x 100 mm dia SW Gully trap setting and jointing with cement mortar 1:1 complete all as specified and directed .

Supply only Integral waterproofing compound

S&F in repairs Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe

S&F for Vitreous china urinal partition white of size 310x700 mm all as specified.

Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S&F factory made mild steel door shutter with frame of minimum size 0.7x0.9 m, includimg one shelf and partition fabricated from 1mm thick mild steel sheet including provision of sheet handle curtain rod, locking arrangement etc, including spray painting over one coat of read oxide primer and fixed the same on existing cupboard nitch with white cement and sand mortar , complete all as specified.

S&F 4mm dia plain mild steel wire, galvanised class 3,as in detached work such as for mosquito nets in fencing including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured)

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, including cleaning, removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed by Engineer-In-Charge.

Pre-cast reinforced cement concrete M-20(1:1.5:3), type A-1, (using 20mm graded crushed stone aggregate), nominal mix, as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs and similar articles with plain faces as specified in clause No- 4.11.16 of SSR Part-I (2009), set in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge.

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed by Engineer-In-Charge.

Excavation in trenches, not exceeding 1.50 mtr wide and not exceeding 1.50mtr in depth; for laying electric cable, not exceeding 10 Sqm on plan and not exceeding 1.50 mtr in depth and getting out, in any type of soil, complete all as specified and as directed by Engineer-In-Charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) of 150mm/200mm bore, set in cement mortar, complete all as specified and as directed by Engineer-In-Charge.

Plain cement concrete M-10(1:3:6), type C-2 (using 40mm crushed stone aggregates) as in bed to drain pipes of 150 mm bore including packing under, and haunching against the sides of pipes after they are laid and tested; after laying, complete all as specified and as directed by Engineer-In-Charge.

Salt-glazed stoneware drain pipes, internal 150 mm, laid in trenches and jointed in cement mortar 1:1, complete all as specified and as directed by Engineer-In-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed by Engineer-In-Charge.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed by Engineer-In-Charge.

S&F Plain, Aluminium sheeting, Alloy 31000 H4 in Crumple joint,ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed)

S & F Aluminum alloy, anodized sliding door bolt with hasp staple( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolt of extruded section or cast aluminium alloy 250 mm long , complete all as specified and directed.

S&F Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work,complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, complete all as specified and directed.

S& F Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws,complete all as specified and directed.

S&F Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails,complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light,fan, bell, socket or power, Sec light) complete,including fixtures and fittings such as switches, ceiling roses, holders, regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement for smooth finishing of holes,small patches etc complete all as specified and directed.

Taking down unserviceable sub main wiring concealed type of any description along with PVC conduit including conduit accessories and made good the disturbed surfaces where ever necessar complete all as specifie and directed

Taking down U/S sheet metal enclosure concealed type with MCBs including making qood the disturbed suface complete all as specified.

Taking up/down old Under Ground cable of any size/type including complete all as specified and directed.

Taking down of old U/S GI bracket set fixed on wall including making good the suface complete all as specified and directed.

Taking down Exhaust fan, dismantling blades,deposite Ex-Fan to MES store yard complete all as specified and directed.

Fixing only Exhaust fan and connecting up including provision of cable from ceiling rose or connector to fan including testing on completion complete all as specified and directed.

Taking down C/Fan, Seailing cable end, dismantling blades and removing fan and blades and deposite to MES store complete all as specified

Dismantling of worn out/burnt out ceiling fans 1200 mm sweep and re-winding the ceiling fan with the same size of super enamelled copper wire, varnishing with approved quality insulating varnish complete including replacement of split/safety pins, locking nut, check nut, complete all as specified and directed by Engineer in charge

Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Disconnecting, removing from the mounting carefully old Electric water heater of capacity 25/50 Ltrs including PVC Connection and handing over to AGE E/M store yard, refixing the same on the same position after completion of the wall repair works including connection, cleaning of out side surface of the Geyser, testing after completion complete. including making good the surface complete all as specified and direrted.

Fixing only electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply and fix heavy duty Exhaust fan 300 mm sweep metal body 900 RPM, 230 Volts, 50 Hz with louver shutter and connecting up including necessary alteration of the hole if necessary and making good the hole, provision of cable 3 core of 0.5 sqmm from ceiling rose to fan complete all as specified and directed.

Point wiring complete with 1.50 sqmm (Nominal area PVC conduit FRLSH insulated, sheathed, multistranded, copper conductor, single core, cable 1100 volts grade drawn through in and including PVC Rigid conduit along with suitable size complete with PVC conduit fittings/ accessories including provn of 1.6 mm thick MS terminal boxes surface/concealed with 3 mm thick hylam pressed laminated/hylamp sheet top cover for housing of switches, sockets, and regulators etc including 1.50 sqmm PVC insulated sheathed stranded copper conductor for earth continuity conductor and connected to common earth dolly for the following :-

(a) One light point/fan point/ exhaust fan point/ bell point controlled by one switch.

(d) One 3 pin 6 amps socket point controlled by one 6 amps switch on independent board.

(c) One 3 pin 6 amps socket point controlled by one 6 amps switch on same board.

(d) One light point controlled by two 2 way switches.

Description all as per item No.32 above, but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm complete all as specified and directed but for One 6 pin 16/6 amps socket outlet point controlled by one 16 amps switch on independent board complete all as specified and directed

Supply and Fixing Switch flush type, 6 amps 240 volts single pole one way

Supply & fixing Piano type switch 6 Amps, 2way, single pole, 240V, IS! Marked complete all as specified and directed.

Switch socket combination 2 in 1, 6A flush type

Socket outlet 2 in 1, 3 pin, 6A

Switch socket combination 3 pin 16A, flush type

Supply and fixing including connection, testing of Fan regulator electronic type with 5 t step control suitable for 1200/1400 mm ceiling fan.

Supply and fixing Ceiling rose surface PVC insulated three plates "JUMBO' type 240 volts

Supply & fix angle lamp holder, polycarbonate insulated body with back plate for bulb complete all as specified and directed.

Supply and fix LED bulb 9 watts, 240Volts, 50Hz pin type and including removing old unserviceable item complete all as specified and directed. Make:- Havells/Crompton/Philios or eauivallent.

S&F Inverter based LED tube light fitting, 20 watt, 4 feet long indoor decorative high | lumen batten 230 volts, AC 50 Hz, 6500K, polycarbonate channel with lithium battery with back up time up to 4 hours and connecting up with twin core twisted flexible copper cable complete Make : Havells/Crompton/Philips or equivallent.

S&F LED tube light fitting, 20 watt, 4 feet long indoor decorative high lumen batten, including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified and directed. Make:- Havells/Crompton/Philips or eauivallent.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple ontics complete with IP 65/66 brotection complete

Material and labour for making suitable hole on brick wall for fixing of Ex-Fan of size 300mm sweep including making good the suface with cement plaster complete all as specified and directed.

Supply and fixing Vertical type sheet metal enclosure DB TPN 6 way double door made powder coated out of CRCA mild steel sheet 1.6 mm thick 415 volts 200 amps rated fitted bus bar dust and vermin proof suitable for incorporation of MCCB as incomer and MCBs as out going duly concealed on wall and making good the disturbed surface including MCCB, four pole, 125 Amps, 415 volts, 50 Hz, 16KA complete all as specified and directed. (Make •- Indo Asian / havells or equivallent)

Supply and fixing in repair Sheet metal enclosures DB's double door factory made power coated out of CRCA mild steel sheet 1.2 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 8 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in wass and making good to disturbed surface and colour matching complete all as specified

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.SP 6 To 32 AMP

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.SPN 32 AM

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning.

M & L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked)cable 1100 volts grade,FRLSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of size 20 mm dia medium grade(MMS) with all connected accessories such as Bend, Tee, Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat and applying putty including cutting and chasing and complete all as specified and directed. Note: - Two run of 6 sqmm single core copper conductor cable and one run of 6 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit only.

Material and labour for Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45X 45X 45 CM, RCC cover 1:2:4 type B1 of size 45X45X6 CM, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old U/S earthing items complete all as specified and directed.

Supply and fix GI bracket pipe of size 40 mm dia medium grade of 1.0 mr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces and including suitable fabricate MS flat iron clamps of 25X6 mm thick -02 Nos suitable for fixing any places with nuts,bolts & washers including grouting on wall etc complete all as specified and directed.

Supply, laying, connecting and testing for XLPE insulated screened PVC bedded galvanised steel strip or wire armoured UG heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area of 25 sqmm 4 core size laid in trenches under floor/roads/hard standing along poles etc all as specified and directed by Engr in Charge. (Excavation and earth work, sand cushioning ,brick protection & GI pipe shall be measured and paid for separately).

Excavation in trenches in soft/loose soil not exceeding 1.5 m wide and not exc. 1.5 mtr deep for laying of cables and getting out soft/loose soil complete all as specified and directed by Engr-in-Charge.

M & L filling dry and clean sand in trenches for cable 8 cm deep below and 15 cm above for cable cushioning complete all as specified and directed by Engr in Charge.

M & L for sub class 'B' brick of size 230x115x75mm laid flat work length equal to width of brick on sand for protection of under ground cable complete all as specified and directed by Engr-in-Charge.

Returning filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cms thick in trenches complete all as specified and directed by Engr-in-Charge.

Removal of surplus soil obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

M & L for GI pipe 40 mm dia Light grade fixing to wall or laying in floors for protection of cable complete all as specified and directed by Engr-in-Charge.

Note:- Deduction for Schedule of credit (Sch 'A' Part-II) to be made of ₹ 164066.00 from the total quoted amount of BOQ while accepting the bid. Details of schedule of credit is given in tender documents.

M/s Joginder Lal Malhotra (BID ID -3300988)

M/S MOHAN LAL SHARMA (BID ID -3301727)

M/s Sekinder Paul Sharma (BID ID -3307130)

Kameshwar builders and contractors (BID ID -3300358)