Special Repairs to LT over head line LT Panel Rewiring in Bldg No P-142 P-319 and other sanctioned works of EM nature under GE (N) Ahmednagar

Amount

Supply,installation,testing and commissioining factory made LT feeder pillar panel CPRI approved, size of panel as per CPRI Specification,double door floor mounted outdoor type,as per IP-65 grade,made out of CRCA sheet 3.15 mm thick of outer body of suitable size with aluminium bus bar 800 Amps,4 strip,(3 phase & Neutral) complete drilled,insulated with colour coaded insulation tape,mounted on insulators etc with RYB LED panel indicater, panel lock with key, internal wiring with suitable size of copper wire,panel should be dust proof,vermin proof,powder coated,locking should be screw type,mechanical type,inter locking,should have danger notice for 415 volt,AC,mounted on 50 x50 x6 mm angle iron frame having minimum 2 feet ground clearanceduly embedded in and including PCC block(1:2:4) type B1 (using 20mm graded stone aggregate) foundation for fixing of panel complete including ternination of all incoming and outgoing cables termination with suitable size thimbles/lugs and glands Nuts & Bolts etc complete all as specifid and directed by Engineer-in-Charge. (Location : MES IB)

M&L Factory made Outdoor type Panel, made out of 16 SWG CRCA Sheet, Powder Coated, Weather Proof, Front Opening Shutter with proper Locking Arrangements, suitable for Totally Enclosed complete and grouting in Cement Concrete 1:2:4 (20mm graded stone aggregate) Work of suitable size including necessary Electric Connections and Testing, Comprising with the followings including Taking down unserviceable Panel, complete all as specified and as directed:-M&L Factory made Outdoor type Panel, made out of 16 SWG CRCA Sheet, Powder Coated, Weather Proof, Front Opening Shutter with proper Locking Arrangements, suitable for Totally Enclosed complete and grouting in Cement Concrete 1:2:4 (20mm graded stone aggregate) Work of suitable size including necessary Electric Connections and Testing, Comprising with the followings including Taking down unserviceable Panel, etc complete all as specified and directed by Engineer-in-Charge. (a) Aluminium Bus-bar 4 Strip, 200 Amp, 415 Volt - 01 Set (b) MCCB 100 Amp - 01 No, 4 Pole, 16 KA (c) MCB 63 Amp, TPN, 16 kA, 415 Volt - 05 No. (d) All MCBs shall be connected through HRC fuse

Material and labour for street light control board / box of size 0.50 X 0.50 X 0.20 m made out of 1.60 mm thick MS sheet fixed / mounted on pole by means of 2 Nos of FT clamps of size 25 X 3 mm comprising the following enclousers and connecting with suitable size of copper cable etc complete all as specified and directed by Engineer-in-Charge. a) MCB, TPN, 63 Amps, - 01 No MAKE: CAT No DSMSCTNF040 OF STANDARD OR equivalent in makes mentioned in list of makes in Appendix `C' b) Timer switch, eletronic, ET 100 operating on 110 / 240 / 415 Volts, 50 Hz MAKE: CAT No SE92006 OF L&T OR equivalent in makes mentioned in list of makes in Appendix `C' c) Contactor ML 2, 40 Amps,415 Volt - 01 No MAKE: CAT No SS90701 OF L&T OR equivalent in makes mentioned in list of makes in Appendix `C' d) All MCB,Contactor shall be connected through HRC fuse

Supply & laying of Telerex DWC(Double wall corrugated) HDPE pipe ISI marked ( Pipe colour orange) of outer dia 110 mm and Inner dia 95 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable including coupler and bends etc complete all as specified and directed by Engineer-in-Charge Make : Rex Polyextrusion Ltd / Veclus Industries / Supreme / Infra / Astrol.

Supply & laying of Telerex DWC(Double wall corrugated) HDPE pipe ISI marked ( Pipe colour orange) of outer dia 90 mm and Inner dia 75 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable including coupler and bends etc complete all as specified and directed by Engineer-in-Charge Make : Rex Polyextrusion Ltd / Veclus Industries / Supreme / Infra / Astrol.

Supply & laying of Telerex DWC(Double wall corrugated) HDPE pipe ISI marked ( Pipe colour orange) of outer dia 63 mm and Inner dia 50 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable icluding coupler and bends etc complete all as specified and directed by Engineer-in-Charge Make : Rex Polyextrusion Ltd / Veclus Industries / Supreme / Infra / Astrol.

Supply & fixing PVC insulated cables aluminium conductor, strandard, 4 Sqmm 2 Core, etc complete all as specified and directed by Engineer-in-Charge.

Material and labour in replacement of 100 mm dia GI Pipe light grade ISI Marked with all fittings laid in trenches , fixed to walls / poles with FI Clamps of suitable size etc complete all as specified and directed by Engineer-in-Charge.

Material and labour in replacement of 50 mm dia GI Pipe light grade ISI Marked with all fittings laid in trenches , fixed to walls / poles with FI Clamps of suitable size etc complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches n exc 1.5 mtr wide and n exc 1.5m in depth , for foundation ,etc or for shafts, wells , cesspits, main holes etc.n exc 10 sqm on plan and n exc 1.5 mtr depth and getting out on soft/ lose soil etc complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading , levelling , watering and well ramming in layers not exc 25cm of any soil etc complete all as specified and directed by Engineer-in-Charge.

Removing excavated materials(soils) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point etc complete all as specified and directed by Engineer-in-Charge.

M&L for bracket for street light fitting, made out from GI Pipe 40 mm Bore (dia), Light Grade, not exc. 1.20 Metre long, bend to required shape and fixing to Poles, etc. with and including Mild Steel Flat Iron Clamps 40x5mm of suitable Length, 2 No. Nuts, Bolts, Washers, etc. including Painting with One coat of Red Oxide Zinc Chrome Primer and Two coats of Aluminium Paint to all Mild Steel Works etc complete all as specified and directed by Engineer-in-Charge.

Dismantling carefully the existing LT overhead line ACSR with cross arm of any size from its position by necessary disconnecting of conductor and removing etc complete all as specified and directed by Engineer-in-Charge.

S&F Shock Proof, Rust Proof, Fire Retradrant, Non-transparent Kiosks Pole Box of size 200x175x100mm made of Engineering Plastic on Piece moulding for Outdoor type, Heavy duty with 4 No. insulated Alunminium Bus-bar of 60 Amp capacity, mounted on Unbreakable Insulators MCB SP, 10 Amp, complete with Aluminium Lugs of suitable size upto 50 Sqmm including 2 No. Flat Iron 40x3mm Clamps with suitable size Mild Steel Bolts, Nuts & Washers, etc. and duly Painted on Both Sides with Two Coats of Synthetic Enemel Paint over a Coat of Red Oxide Zinc Chrome Primer Pole Box of any description from any Height, etc complete all as specified and directed by Engineer-in-Charge..

Supply and Laying in trenches or drawn through pipe or fixed on wall / poles , LT UG cable 1100 Volts, heavy duty XLPE insulated, screened, PVC bedded, galvanised steel strip or wired armoured with aluminium conductor after removing old cable of following size:-

10Sqmm 2 core

10 sqmm 4 Core

16 sqmm 4 core

25 Sqmm 4 core

35 Sqmm 4 core

95 Sqmm 3.5 core

120 Sqmm 3.5 core

240 Sqmm 3.5 core

185 Sqmm 3.5 core

Supply,installation,testing and commissioining factory made LT feeder pillar panel CPRI approved, size of panel as per CPRI Specification,double door floor mounted outdoor type,as per IP-65 grade,made out of CRCA sheet 3.15 mm thick of outer body of suitable size with aluminium bus bar 1000 Amps,4 strip,(3 phase & Neutral) complete drilled,insulated with colour coaded insulation tape,mounted on insulators etc with RYB indicater,internal wiring with suitable size of copper wire,panel should be dust proof,vermin proof,powder coated,locking should be screw type,mechanical type,inter locking,should have danger notice for 415 volt,AC,mounted on 50 x50 x6 mm angle iron frame having minimum 2 feet ground clearanceduly embedded in and including PCC block(1:2:4) type B1 foundation for fixing of panel complete including ternination of all incoming and outgoing cables with suitable size thimbles/lugs and glands Nuts & Bolts etc complete all as specified and directed by Engineer-in-Charge. (Location : Eletronic Wing Line)

Incoming : - (i) MCCB 630 Amp, Adjustable Thermal & Adjustable Magnetic setting type with , 4 Pole,50KA - 01 No. (Ics=100% Icu) (ii) Volt meter 0 to 500 Volts, Square flush pattern, digital type – 01 No (iii) Amp meter square flush pattern 0 to 400 Amps digital type -01 No. (iv) Indicating lamp LED type one set in incoming phases. (v) Internal wiring with PVC insulated copper conductor multi stranded cable 1100 Volt grade IS 694 marked of appropriate gauge including all copper lugs (vi) Connection from MCCB to Busbar shall be of solid Aluminium conductor (vii) MCCB shall be provided with suitable spreader of aluminium conductor for fixing of incoming cable (viii) KWH meter three phase CT operated as per suitable capacity of LT Panel Outgoing ways :- (i) MCCB 200 Amps Adjustable Thermal & Adjustable Magnetic setting type ,4 pole,36 KA-04 Nos (Ics = 100% of Icu) (ii) MCCB 100 AMps, - 02 Nos, 16 KA, 4 Pole. (ICS = 100% ICU)

Notes:- 1. The Panel Shall be approved by CPRI. 2. The rates Quoted shall include for earth work,Plinth protection 75mm thick, 90 cm wide, PCC type (1:3:6) C-2 using 40mm graded stone aggregate around the panel and excavation for angle iron frame for foundation of panel board up to 0.50 m below GL in any type of soil and PCC 1:4:8 type D2 (using 40mm graded stone aggregate) filling in foundation. The ground clearance of panel board shall be 0.40 M from GL to the bottom of panel board. 3. All MCCBs shall be handle operated and connected through HRC Fuse 4.All incoming power MCCBs and outgoing MCCBs connected through busbar and control wiring connected through copper cable

Supply,installation,testing and commissioining factory made LT feeder pillar panel CPRI approved, size of panel as per CPRI Specification,double door floor mounted outdoor type,as per IP-65 grade,made out of CRCA sheet 3.15 mm thick of outer body of suitable size with aluminium bus bar 1000 Amps,4 strip,(3 phase & Neutral) complete drilled,insulated with colour coaded insulation tape,mounted on insulators etc with RYB indicater,internal wiring with suitable size of copper wire,panel should be dust proof,vermin proof,powder coated,locking should be screw type,mechanical type,inter locking,should have danger notice for 415 volt,AC,mounted on 50 x50 x6 mm angle iron frame having minimum 2 feet ground clearanceduly embedded in and including PCC block (1:2:4) type B1 (using 20mm graded stone aggregate) foundation for fixing of panel complete including ternination of all incoming and outgoing cables with suitable size thimbles/lugs and glands Nuts & Bolts etc complete all as specified and directed by Engineer-in-Charge. (Location : CHQ) Incoming : (i) MCCB 630 Amp, Adjustable Thermal & Adjustable Magnetic setting type with , 4 Pole,50KA - 01 No. (Ics=100% Icu) (ii) Volt meter 0 to 500 Volts, Square flush pattern, digital type – 01 No (iii) Amp meter square flush pattern 0 to 400 Amps digital type -01 No. (iv) Indicating lamp LED type one set in incoming phases. (v) Internal wiring with PVC insulated copper conductor multi stranded cable 1100 Volt grade IS 694 marked of appropriate gauge including all copper lugs (vi) Connection from MCCB to Busbar shall be of solid Aluminium conductor

(vii) MCCB shall be provided with suitable spreader of aluminium conductor for fixing of incoming cable (viii) KWH meter three phase CT operated as per suitable capacity of LT Panel Outgoing ways :- (i) MCCB 160 Amps adjudtable type ,3 pole,25 KA-07 Nos (Ics=100% Icu). (ii) Change over switch on load 400 Amp adjustable type, 4 pole, - 01 No Notes:- 1. The Panel Shall be approved by CPRI. 2. The rates Quoted shall include for earth work,Plinth protection 75mm thick, 90 cm wide, PCC type (1:3:6) C-2 40mm using graded stone aggregate around the panel and excavation for angle iron frame for foundation of panel board up to 0.50 m below GL in any type of soil and PCC 1:4:8 type D2 (using 40mm graded stone aggregate) filling in foundation. The ground clearance of panel board shall be 0.40 M from GL to the bottom of panel board. 3. All MCCBs shall be handle operated and connected with HRC Fuse 4.All incoming power MCCBs and outgoing MCCBs connected through busbar and control wiring connected through copper cable

Supply,installation,testing and commissioining factory made LT feeder pillar panel CPRI approved, size of panel as per CPRI Specification,double door floor mounted outdoor type,as per IP-65 grade,made out of CRCA sheet 3.15 mm thick of outer body of suitable size with aluminium bus bar 800 Amps,4 strip,(3 phase & Neutral) complete drilled,insulated with colour coaded insulation tape,mounted on insulators etc with RYB indicater,internal wiring with suitable size of copper wire,panel should be dust proof,vermin proof,powder coated,locking should be screw type,mechanical type,inter locking,should have danger notice for 415 volt,AC,mounted on 50 x50 x6 mm angle iron frame having minimum 2 feet ground clearanceduly embedded in and including PCC block(1:2:4) type B1 (using 20mm graded stone aggregate) foundation for fixing of panel complete including ternination of all incoming and outgoing cables with suitable size thimbles/lugs and glands Nuts & Bolts etc complete all as specified and directed by Engineer-in-Charge (Location : K2Z & MI Room)

Incoming : - (i) MCCB 400 Amp Adjustable Thermal & fixed Magnetic setting type with , 4 Pole, 50KA - 01 No. (Ics = 100% of Icu) (ii) Volt meter 0 to 500 Volts, Square flush pattern, digital type – 01 No (iii) Amp meter square flush pattern 0 to 400 Amps digital type -01 No. (iv) Indicating lamp LED type one set in incoming phases. (v) Internal wiring with PVC insulated copper conductor multi stranded cable 1100 Volt grade IS 694 marked of appropriate gauge including all copper lugs (vi) Connection from MCCB to Busbar shall be of solid Aluminium conductor (vii) MCCB shall be provided with suitable spreader of aluminium conductor for fixing of incoming cable (viii) KWH meter three phase CT operated as per suitable capacity of LT Panel

Outgoing ways :- (i) MCCB 160 Amps Adjustable Thermal & Adjustable Magnetic setting type ,4 pole,16KA - 05 Nos (Ics = 100% of Icu) (ii) On-load change over switch 4 pole, 200 Amp - 01 No Notes:- 1. The Panel Shall be approved by CPRI. 2. The rates Quoted shall include for earth work, Plinth protection 75mm thick, 90 cm wide, PCC type (1:3:6) C-2 using 40mm graded stone aggregate around the panel and excavation for angle iron frame for foundation of panel board up to 0.50 m below GL in any type of soil and PCC 1:4:8 type D2 (using 40mm graded stone aggregate) filling in foundation. The ground clearance of panel board shall be 0.40 M from GL to the bottom of panel board. 3. All MCCBs shall be hand operated and connected through HRC Fuse 4.All incoming power MCCBs and outgoing MCCBs connected through busbar and control wiring connected through copper cable

Supply,installation,testing and commissioining factory made LT feeder pillar panel CPRI approved, size of panel as per CPRI Specification,double door floor mounted outdoor type,as per IP-65 grade,made out of CRCA sheet 3.15 mm thick of outer body of suitable size with aluminium bus bar 800 Amps,4 strip,(3 phase & Neutral) complete drilled,insulated with colour coaded insulation tape,mounted on insulators etc with RYB indicater,internal wiring with suitable size of copper wire,panel should be dust proof,vermin proof,powder coated,locking should be screw type,mechanical type,inter locking,should have danger notice for 415 volt,AC,mounted on 50 x50 x6 mm angle iron frame having minimum 2 feet ground clearanceduly embedded in and including PCC block(1:2:4) type B1 using 20mm graded stone aggregate foundation for fixing of panel complete including ternination of all incoming and outgoing cables with suitable size thimbles/lugs and glands Nuts & Bolts etc complete all as specifid and directed by Engineer-in-Charge (Location : K2Z)

Incoming : - (i) MCCB 400 Amp Adjustable Thermal & Adjustable Magnetic setting type with , 4 Pole, 50 KA - 01 No.(Ics = 100% of Icu) (ii) Volt meter 0 to 500 Volts, Square flush pattern, digital type – 01 No (iii) Amp meter square flush pattern 0 to 400 Amps digital type -01 No. (iv) Indicating lamp LED type one set in incoming phases. (v) Internal wiring with PVC insulated copper conductor multi stranded cable 1100 Volt grade IS 694 marked of appropriate gauge including all copper lugs (vi) Connection from MCCB to Busbar shall be of solid Aluminium conductor (vii) MCCB shall be provided with suitable spreader of aluminium conductor for fixing of incoming cable (viii) KWH meter CT operated as per suitable capacity of LT Panel

Outgoing ways :- (i) MCCB 200 AmpsAdjustable Thermal & Adjustable Magnetic setting type ,4 pole,25 KA-04 Nos (Ics = 100% of Icu) (ii) MCCB 63 Amps, 16 KA - 02 Nos. (iii) Change over switch on-load 200 Amps, 4 Pole - 01 No Notes:- 1. The Panel Shall be approved by CPRI. 2. The rate Quoted shall include for earth work,Plinth protection 75mm thick, 90 cm wide, PCC type (1:3:6) C-2 using 40mm graded stone aggregate around the panel and excavation for angle iron frame for foundation of panel board up to 0.50 m below GL in any type of soil and PCC 1:4:8 type D2 (using 40mm graded stone aggregate) filling in foundation. The ground clearance of panel board shall be 0.40 M from GL to the bottom of panel board. 3. All MCCBs shall be hand operated and connected through HRC Fuse 4.All incoming power MCCBs and outgoing MCCBs connected through busbar and control wiring connected through copper cable

M&L Factory Made Panel made out of CRCA Sheet 3.0mm thick, Out Door type, Front Opening Double Doors with proper Locking Arrangements having Weather Proof duly Powder coated and mounted on Mild Steel Angle Iron Frame 40x40x5.0mm (4 No.) of suitable Height duly painted with Two Coats of Black Enamel Paint over a coat of Red Oxide Zinc Chrome Primer and grouting in Cement Concrete 1:2:4 (20mm graded stone aggregate) Block of size 30x30x45 Cm including necessary Earthwork, providng Electric Connections and Testing, etc complete all as specified and directed by Engineer-in-Charge and Comprising with the following :- (a) Aluminium bus bar 200 Amp capacity, 4 Strip, 450mm long - 01 Set (b) MCCB 100 Amp, 4P,415 V - 01 No. (c) MCB TPN 63 Amps - 05 Nos (d) Location : CHQ

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including Taking down/out Unserviceable Earthing of any description, complete all as per specified and as directed. Note :- Cost of earthing lead /strip & GI pipe 40mm up to 7.5 m is included in cost of above item

Supply & laying of Telerex DWC (Double wall corrugated) HDPE pipe ISI marked ( Pipe colour orange) of outer dia 120 mm and Inner dia 103 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable icluding coupler and bends etc complete all as specified and directed by Engineer-in-Charge Make : Rex Polyextrusion Ltd / Veclus Industries / Supreme / Infra / Astrol.

Supply & fix in replacement of single pointed air termination Copper rod, 12 mm dia, 300 mm long including Taking down existing copper rod etc complete all as specified and directed by Engineer-in- Charge.

Supply & fix in replacement of Copper strip 25 mm x 3.15 mm Complete with saddles and fixing screws on including epoxy Insulater for Fitting the strip.including Taking down existing Al/cu strip etc complete all as specified and directed by Engineer-in-Charge. (note: Rate include cost of insulator)

Supply & install in replacement of GI strip 32 mm x 6 mm buried ground/floor/surface/roof including taking doown existing GI Strip etc complete all as specified and directed by Engineer-in-Charge.

M&L for earthing of poles/system with galvanised earth plate 60x60 cm x 6.30 mm thick electrode of size and 32 x 6mm GI strip buried vertically in ground not less than 2.25 mtr below ground level with top edge of the plate not less than 1.5 mtr below ground level and connected to copper strip dia by means of nuts, bolts and washers and encased in and including 40mm dia GI medium grade pipe upt 2.4 mtr height form ground level fixed by MS flat iron clamp 40mm x 5mm with nut, bolt and washers, GI strip fixed to base along pole and connected to over head line for providing earthing to HT pole/feeder AB switch LA complete with charcoal dust, salt packed around plate 150 mm thick including watering GI pipe, medium grade 20 mm dia with blanking cap 1.5 mtr long fixed to funnel with wiremesh complete with PCC chamber and RCC chamber over all as per Electrical Plate No 5 of SSR Part I - 2009 incl excavation and earth work in any type of starta and testing on compeltion etc complete all as specified and directed by Engineer-in-Charge Note :- Cost of earthing strip & GI pipe 40mm up to 7.5 m shall be included in cost of above item

M&L for Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos. 8mm dia 25mm long hex. head screw etc including Taking down existing complete all as specified and directed.complete all as specified and directed by Engineer-in-Charge

S&F street light fitting (LED) of capacity 60 W, 6000-6500 Lumen- 6000 Lm, 10 KV in build surg protection IP-66, die cast aluminium housing with toughend glass and 4 Sqmm service wire for necessary connection including taking down existing unsv street lightetc complete all as specified and directed by Engineer-in-Charge.Make : Havells cat part No : ENDURAPEARLNEOSL60WLED757PASYTOPC or equivalent makes mentioned in list of makes in Appendix `C'

S&F Shock Proof, Rust Proof, Fire Retradrant, Non-transparent Kiosks Pole Box of size 200x175x100mm made of Engineering Plastic on Piece moulding for Outdoor type, Heavy duty with 4 No. insulated Alunminium Bus-bar of 60 Amp capacity, mounted on Unbreakable Insulators MCB SP, 10 Amp, complete with Aluminium Lugs of suitable size upto 50 Sqmm including 2 No. Flat Iron 40x3mm Clamps with suitable size Mild Steel Bolts, Nuts & Washers, etc. and duly Painted on Both Sides with Two Coats of Synthetic Enemel Paint over a Coat of Red Oxide Zinc Chrome Primer Pole Box of any description from any Height, complete all as specified and as directed.MAKE : HENSEL/ SCHNEIDER/ SINTEX/ UNIVERSAL SWITCH GEARS CONTROL.

S&F MCB Distribution Board, SPN 4-way, 240 Volt AC, Single Door type of Steel Sheet Phoshotised Powder painted with 200 Amp Neutral Bars, Earth Bar and connecting up etc complete all as specified and directed by Engineer-in-Charge.

S&F MCB 63 Amp, Triple Pole & Neutral, 4 way, 'C' Series, 50 Hz, 10 kA, 415 Volt and etc complete all as specified and directed by Engineer-in-Charge.

S&F MCB 6 Amp to 32 Amp, Single Pole & Neutral, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up etc complete all as specified and directed by Engineer-in-Charge.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 20/25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, etc complete all as specified and directed by Engineer-in-Charge.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, etc complete all as specified and directed by Engineer-in-Charge.

S&F Ceiling Rose Surface type, Bakelite 65x50mm, 3 Terminal suitable for 230 Volt AC, 6 Amp and connecting up including Taking down/ out unserviceable Ceiling Rose, etc complete all as specified and directed by Engineer-in-Charge.

S&F Socket Outlet 16 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up including Taking down/ out unserviceable Socket Outlet, etc complete all as specified and directed by Engineer-in-Charge.

S&F Switch Piano Flush type, 16 Amp, Single Pole, 1-way, 230 Volt AC and connecting up including Taking down/ out unserviceable Switch Piano, etc complete all as specified and directed by Engineer-in-Charge.

S&F switch piano type flush single pole one way 230 Volts AC 5/6Amps, including necessary connection etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of LED Street light Luminaries 30 watt, Lumens utput 3000 with pressure die-cast aluminium housing with heat resistance toughtened glass & IP 65 protection, fixed with suitable size of GI Bracket, Clamp,Nut, Bolt and washer , connection with 1.5 Sqmm 3 run copper wire from junction box etc complete all as specified and directed by Engineer-in-Charge.

S&F sub main wiring with two single core PVC insulated,unsheathed, FRLSHstranded copper conductor cable 4 Sqmm with 4 Sqmm PVC insulated, unsheathed, FRLSH stranded copper conductor cable as earth wire drawn through and including PVC Casing and capping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge Note : 1. Porper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. Two run of 4 Sqmm cable i.e for one run for phase, one run for neutral with one run of 4 Sqmm cable for earth and one run of PVC Casing & caping shall be measured as one unit

Supplied and fix rigid non metallic PVC conduit exclusive of boxes but inclusive of all tees,bends,elbows,reducers,bell mouth tube ends and fixing accessories such as coupler ,lock ,nuts etc of size 40 mm etc com[plete all as specified and directed by Engineer-in-Charge.

M & L steel tubular poles, complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.00 Mtrs Long) etc com[plete all as specified and directed by Engineer-in-Charge.

M & L for PCC(1:3:6) type C-2 using 40mm grade stone aggregates as foundation of pole and similar work etc com[plete all as specified and directed by Engineer-in-Charge.

M & L for PCC(1:2:4) type B-1 using 20mm grade stone aggregates for coping and similar work etc com[plete all as specified and directed by Engineer-in-Charge.

S&F new street light fitting (LED) of capacity 60 W, 6000-6500 Lumen- 6000 Lm, 10 KV in build surg protection IP-66, die cast aluminium housing and 4 Sqmm service wire for necessary connection complete all as specified and directed by Engineer-in-Charge.Make : Havells cat part no ; ENDURAPEARLNEOSL60WLED757PASYTOPC or equivalent makes as mentioned in list of makes in Appendix `C'

Supply and fixing LED flood light fitting 200 Watts with high luminious efficiency protected to IP65 with front toughened glass with all accessories and including connecting up from ceiling rose to fitting with 4 sqmm twin core aluminium cable (approx 2 Mtrs) etc complete all as specified and directed by Engineer-in-Charge

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Chage

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 Sqmm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories PVC boxes (upto 12 module suitble for Mylinc series of Legrand including white plates with frame upto 12 module of make suitable for Mylinc Series) for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS cable as earth continuity conductor to common earth & connecting to earth dolly for the following, etc complete all as specified and directed by Engineer-in-Charge. Note : 1. Porper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2.Wiring shall be done as per complaints recd from user only on required basis it is not necessary to do whole wiring of any whole bldg 3. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

One fan point controlled by switch 5 Amp single pole one way

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

All as per Item No 66 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase, Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board.

S&F Modular Switch, 6 Amp, one way, one Module. etc complete all as specified and directed by Engineer-in-Charg.

S&F Modular Switch, 16 Amp, onw way, one Module. etc complete all as specified and directed by Engineer-in-Charge.

S&F Modular Socket Outlet 6 Amp, 2/3 pin, combined two module etc complete all as specified and directed by Engineer-in-Charge.

S&F Modular Socket Outlet 6 Amp / 16 Amp - 2/3 pin combined two module etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing lamp holder (Angular/Straight), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement double door Sheet metal enclosures factory made DBs SPN, 8 way ,240 volts ,protection class IP-42, suitable for fixing of MCBs, Isolators etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed. Make: Legrand ,Cat No: 5076 11 or equivalent makes mentioned in list of makes in Appendix `C'

Supply & fixing MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, SPN, AC, 240 volts of 40 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply and fix Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 20 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge Make:Philips Model Name Astra line or equvivalent makes mentioned in list of makes in Appendix `C'

S&F Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 10 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with 2 core seathed copper conductor cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement energy saving and environmental friendly long life LED street light 25 Watt (Bldg security light) made up of pressure die cast aluminium housing with mild power LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V , 50 HZ etc complete all as specified and directed by Engineer-in-Charge Make -Havell's Cat Part: (ENDURAPEARLSL25W MP) ENDURAPEARLSL25WLED757SASYTOPCMP or equivalent makes mentioned in list of makes in Appendix `C'

Supply & fix exhaust fans with louvers of steel sheet steel body AC single phase 230/ 240 V of size 300 mm sweep with blades and frame etc complete all as specified and directed by Engineer-in-Charge.

M&L for Cutting the existing in any type of wall with suitable dia for fixing the exhaust fan with necessary arrangements etc complete all as specified and directed by Engineer-in-Charge

Boaring of holes under road crossing, pavment, hardstanding by trenchless technology using ultra sound technique and necessary machine including HDPE pipe 150 mm dia suitable for 0.4 mpa working pressure without any damage to existing structure and making good to match the adjoining surface / structure etc complete all as specified and directed by Engineer-in-Charge.

An amount of Rs 44,847.00.00 shall be deducted from BOQ on account of schedule of credit

metro electrical services