8124/SAR-T-51/2024-25 PROVN OF PARKING SHEDS FOR MD ACCN AND OTM ACCN AND PROVN OF KITCHEN CABINETS, UTENSIL RACKS AND MIRROR CABINET IN MD ACCN AT AF STN SARSAWA UNDER GE (AF) SARSAWA

Amount

Excavation in post holes each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm, watering and removing surplush soil to a distance n exc 50m and making good surface complete all as directed by Engineer-in-charge and all as specified.

M&L for PCC Type C2 1:3:6 (40 mm graded aggregate) Cement concrete in foundations, filling and mass-concrete complete all as specified & directed by Engr-in-Charge.

M&L steel work in tubular truss, purlin rafter columns etc including welding ,butt welded tubes conferming to IS-1161-1979 grade St-240, complete all as directed by Engineer-in-charge.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed by Engineer-in-charge and all as specified.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying one coat of red oxide primer complete all as directed by Engineer-in-charge and all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screwas as specified fixed etc complete all as specified & directed by Engr-in-Charge.

M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-290 Gde E-165 etc complete all as specified & directed by Engr-in-Charge.

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 deep and getting out in soft loose soil.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in soft/loose soil.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above or below the starting point complete all as specified& directed by Engr-in-Charge.

M&L for 100 mm thick PCC 1:4:8 type D -2 using 40 mm graded aggregate as in sub base of path/hardstanding complete all as specified & directed by Engr-in-Charge.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed by Engr-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

S&F PVC bathroom cabinet size 450mm x 600mm and width 95mm and front side looking mirror shutter fixed to wall with rawl plug complete all as specified and as directed.

Providing Kitchen cabinet in required shape & size at site made out of 18 to 20 mm thick one side decorative lamination & other side balancing lamination solid PVC board consisting of carcase 18 to 20mm thick solid PVC board & provision of shutters made out of 18 to 20mm thick one side decorative laminated solid PVC board all required brackets, screws etc. The panels shall be fabricated using adhesive and screws where ever required. All edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned or directed including SS storage basket & drawers for food items & kitechen utensils of any size and shape as approved by Engr-in-Charge. (Note :- SS items measured & paid separately against Item No 19 below).

S&F 150mm oval shape extruded brass handles, fabricated type polished fixed to drawer/cabinet/door/wardrobe pull handle etc complete all as specified & directed.

S & F stainless steel pie corner hinge 135 degree and size 150x150x100mm complete all as specified & directed by Engr-in-Charge.

S&F FAST DM01SS Stainless Steel Furniture Door Catcher Magnet Size No. 2 for for Wadrobe, Cupboard and Almirah Door. (SS MAT) with Mounting Screw complete all as specified

M&L stainless steel (Grade 304) kichen cabinet storage basket & drawers for food items & kitchen utensils of any size and shape, corrosion resistance, seamless glossy finish, high quility, pullout basket with telescopic drawer channel of any size etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size,complete all as specified & directed.

S&F stainless steel Kitchen plate rack of overall minimum size 750mm x 750mm and 230mm deep, with partitions for small/large plates etc made out of stainless steel 24 Gauge, fixed with rawl plug and CP steel screws all as directed. Note : Weight of rack shall not be less than 4.00 Kg.

S&F stainless steel Kitchen plate rack of overall minimum size 900mm x 900mm and 230mm deep, with partitions for small/large plates etc made out of stainless steel 24 Gauge, fixed with rawl plug and CP steel screws all as directed. Note : Weight of rack shall not be less than 6.00 Kg.

SINGH CONSTRUCTION CO. (BID ID -3117737)

G.H. INFRASTRUCTURE PRIVATE LIMITED (BID ID -3115740)

SUBHASH CHAND CONTRACTOR (BID ID -3127847)