Repairing and Painting of SHANTI MANCH at Dankuni Coal Complex Township

Amount

Item Description/ Heading

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1 cement : 4 fine sand) [IT No- 14.1.1, CPWA-18, Pg- 246]

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. [IT No- 15.56, CPWA-18, Pg- 263]

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate [IT No- 11.3.1, CPWA-18, Pg- 193]

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) [IT No- 5.1.2, CPWA-18, Pg- 95]

Centering and shuttering including strutting, propping etc. and removal of form work for : 4.3.2 Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.[IT No- 4.3.2, CPWA-18, Pg- 87]

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Hard drawn steel wire.[IT No- 5.22A.2, CPWA-18, Pg- 87]

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) [IT No- 6.1.1, CPWA-18, Pg- 108]

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : Old work (one or more coats) [IT No- 13.90.1, CPWA-18, Pg- 236]

Finishing walls with Acrylic Smooth exterior paint of required shade : 13.111.2 Old work (One or more coat applied @ 0.90 ltr/10 sqm). [IT No- 13.111.2, CPWA-18, Pg- 238]

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. [IT No- 13.85.3, CPWA-18, Pg- 236]

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth Complete. [IT No- 13.80, CPWA-18, Pg- 235]

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work. [IT No- 13.99.1, CPWA-18, Pg- 237]

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. [IT No- 13.91, CPWA-18, Pg- 236]

White washing with lime to give an even shade : New work (three or more coats) [IT No- 13.37.1, CPWA-18, Pg- 231]

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete [IT No- 13.88, CPWA-18, Pg- 236]

Providing and fixing M.S Grill

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Sal wood [IT No- 9.1.2, CPWA-18, Pg- 146]

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. [IT No- 10.1, CPWA-18, Pg- 183]

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 10.30.1 4.0 mm thick glass panes [IT No- 10.30.1, CPWA-18, Pg- 187]

Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately) : White face insulating board 12 mm thick. [IT No-12.24.2.1 CPWD-18,pg-214]

Providing corrugated G.S sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.8mm thick with zinc coating not less than 275gm/m2[IT No-12.1.2 CPWD-18,pg-211]

Providing ridges or hips of width 60cm overall width plain G.S sheet fixed with polymer coated J or L hooks, bolts and nuts8mm dia G.I limpet and bitumen washers complete. 0.80mm thick with zinc coated not less than 275gm/m2[IT No-12.4.1 , CPWD-18,pg-211]

Providing and fixing aluminium tee channels (heavy duty) with rollers & stop end in pelmets as curtain rod. [IT No-9.104, CPWD-18,pg-160]

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete with : 22.8.1 Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322 [IT No- 22.8.1, CPWA-18, Pg- 390]

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws [IT No- 9.21.1, CPWA-18, Pg- 150]

35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-charge. Non decorative finish (matt finish) [IT No- 9.142.1, CPWA-18, Pg- 169]

French spirit polishing : 13.103.1 One or more coats on old work. [IT No- 13.103.1, CPWA-18, Pg- 238]

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White. [IT No- 17.18.1 , CPWA-18, Pg- 302]

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. [IT No- 17.15, CPWA-18, Pg- 302]

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : Black solid plastic seat with lid [IT No- 17.20.2, CPWA-18, Pg- 302]

Providing and fixing Urinal

Providing and fixing CP Pillar Cock (ESSCO)

Providing and fixing CP Bib Cock (ESSCO)

Providing and fixing Toilet Shower

Providing and fixing PVC pipe 15 mm

Providing and fixing PVC pipe 20 mm

Providing and fixing PVC pipe 25 mm

Providing and fixing kitchen sink including making all connections excluding cost of fittings. White glazed fire clay sink of size 600x450x250 mm. [IT No- 17.26.1, CPWA-18, Pg- 303]

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400 mm [IT No- 17.25.2, CPWA-18, Pg- 303]

Providing and fixing Connective pipe

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. [IT No- 17.31, CPWA-18, Pg- 303]

PVC Shower

Providing and fixing PVC Ball Cock set (3/4")

Providing and fixing angular Cock

Providing and fixing CP Stop Cock

Providing and fixing PVC Bib Cock

Making one set of Scaffolding (a) 3.90 m height

Making one set of Scaffolding (b) Extra height for additional 3.6m height

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. [IT No- 15.60, CPWA-18, Pg- 263]

PVC Tank

Repairing of existing acuintic with jute cloth/ ceramic fibre glass wool.

Total impact of GST for the purpose of CTC

M/s Aristo engieering co

J S CONSTRUCTION