REPAIR TO EXT ELECT SUPPLY OF OH LINE UG CABLE PANEL BOARD AND OUTSOURCING SERVICES FOR ELECTRIC INSTLNS WITH CONNECTED WORKS UNDER GE I GOS

Amount

Excavation in trenches in hard/dense soil n.exc 1.5 mtr wide and n.exc 1.5 mtr depth and getting out pole foundation/cable trench complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.

Removing surplus excavated material not exc 50 mtrs and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Supply and providing sand cushioning with dry clean sand 8 cm below cable and 15 cm above the cable complete all as specified and directed. Note : Punned thickness shall be measured for the purpose of payments.

Supply and laying Fly ash bricks in trenches for cable protection with length of brick perpendicular to length of cable complete all as specified and directed.

Material and labour for plain cement concrete M-10, nominal mix type C-2 (with using 40 mm graded stone arrgegate ) as in sub base, foundation, filling and mass concrete , complete all as specified.

Material and labour for plain cement concrete M-15, nominal mix type B-1 (using 20mm graded crushed stone aggregate), as in coping/road crossing, etc. including necessary form work ,complete all as specified.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded 120 Sqmm 3.5 core with aluminium conductor 1100 V grade, laid in trenches/ along poles, ducts or through sleeve including taking out existing unserviceable cable complete all as specified and directed. Make: Polycab/Havells/Gloster.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded 70 Sqmm 3.5 core with aluminium conductor 1100 V grade, laid in trenches/ along poles, ducts or through sleeve including taking out existing unserviceable cable complete all as specified and directed. Make: Polycab/Havells/Gloster.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded 50 Sqmm 3.5 core with aluminium conductor 1100 V grade, laid in trenches/ along poles, ducts or through sleeve including taking out existing unserviceable cable complete all as specified and directed. Make: Polycab/Havells/Gloster.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded 35 Sqmm 3.5 core with aluminium conductor 1100 V grade, laid in trenches/ along poles, ducts or through sleeve including taking out existing unserviceable cable complete all as specified and directed. Make: Polycab/Havells/Gloster.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded 25 Sqmm 3.5 core with aluminium conductor 1100 V grade, laid in trenches/ along poles, ducts or through sleeve including taking out existing unserviceable cable complete all as specified and directed. Make: Polycab/Havells/Gloster.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded 10 Sqmm 2 core with aluminium conductor 1100 V grade, laid in trenches/ along poles, ducts or through sleeve including taking out existing unserviceable cable complete all as specified and directed. Make: Polycab/Havells/Gloster. Note for item No. 8 to 13 : Earth work, sand cushioning and bricks will be measured and paid separately under relevant items.

Supply and fixing for GI tubing light grade 40mm bore with all fittings laid in trenches or under road crossing or fixed along walls/poles as protection pipe with clamps, nut, washer bolts (where necessary) including taking down existing pipe complete all as specified and directed.

Supply and fixing for GI tubing medium grade 80mm bore with all fittings laid in trenches or under road crossing or fixed along walls/poles as protection pipe with clamps, nut, washer bolts (where necessary) including taking down existing pipe complete all as specified and directed.

Supply and replacement street light fitting LED type 15 Watt new generation energy saving powder coated pressure die cast aluminum compact LED street light and electronic driver with GI tubing 25mm dia light grade, mounting bracket with its clamp incl two coats of synthetic enamel paint over a coat red oxide primer and with all accessories, testing & commissioning complete all as specified and directed. Make : C&S Cat Part No LTESS15WLED or equivalent in Polycab/Havells.

Taking down old unsv LT panel and supply, install and commissioning of LT panel board outdoor type, factory fabricated prewired, CPRI aproved, cubical type of appropriate size in door, dust and vermin proof, made out of 50x50x6mm angle iron frame/legs and 3.15 mm thick CRCA sheet with openable shutters on both sides (front & rear), and painting to all steel surfaces internally and externally with two coats of powder coated paint over a coat of red oxide zinc chrome primer suitable for 440 volts, 3 phase 4 wire system enclosed with copper bus bar of 400 amp for R,Y,B phases and 400 amps for neutral, having locking arangement mounted on four legs 90cm high (30 cm below ground level and 60 cm above ground level), embedded in PCC (1:2:4 ) type B2 block each of size 200x200x300mm complete all as specified & directed by the Engr-in-Charge to accommodate the following accessories and the panel should have arrangement sufficient space to work easily :- Incoming (a) Copper bus bar 400 A for three phase and neutral duly insulated with sleeves of different colour RYB . (b) MCCB 4 Pole 250A 35 KA - 1 Nos (Make : C&S Cat No CSE2N250ATM4P-* or equivalent in L&T/HPL. (c) Digital multi functional Panel meter showing V/I.Fq, PF along with CTs , Make:-C&S/Schneider/Indoasian/ - 01 Set (d) Indicators lamp LED type RYB 240 volts - 01 Set. Outgoing (e) MCCB 4 Pole 160A 35 KA - 1 No, (Make : C&S Cat No CSE2N250AATM4P-* or equivalent in L&T/HPL) (f) MCCB 4 Pole 63A 25 KA - 2 Nos, One Spare. (Make : C&S Cat No CSE1M125ATM4P-* or equivalent in L&T/HPL) (g) MCCB 4 Pole 50A 25 KA - 1 Nos (Make : C&S Cat No CSE1M125FMU4P-* or equivalent in L&T/HPL) (j) MCB 2 Pole 32 Amp 'C' Series - 2 Nos (Make : C&S Cat No CSMBS1C32N or equivalent in Polycab/Indoasian) (Note : (i) Incoming and outgoing cable shall be fixed with appropriate size of copper thimble. (ii) Apron shall be provided at bottom for protection of cable to avoid entry of vermins, reptiles. (iii) Entries of all sizes of cables in panel should be done through adequate size of metallic cable glands.

Supply and replacement street light fitting LED type 45 Watt new generation energy saving & environmental friendly long life versatile powder coated pressure die cast aluminum high power with heat resistant toughened glass IP65 and electronic driver with GI tubing 40mm dia light grade ,mounting bracket with its clamp incl two coats of synthetic enamel paint over a coat red oxide primer and with all accessories ,with lamp incl connecting of with 2 run of flexible copper/aluminium conductor of size 1.5 sq mm cable from fitting to junction box or pole, testing & commissioning complete all as specified and directed. Make : C&S Cat Part No LTESS18X2.5HPLED/LS or equivalent in Polycab/Havells.

Supply and replacement decorative LED post top lantern luminaire with diffuser and painted aluminium deflector complete with connecting of suitable size of wire all as specified and directed by Engr-in-Charge. Make C&S Cat part No LTGLC20WHPLED/W or equivalent in Polycab/Havells.

Supply and replacement decorative LED bollard light with opal diffuser and aluminium reflector complete with connecting of suitable size of wire all as specified and directed by Engr-in-Charge. Make C&S Cat part No LTGLC6W LED or equivalent in Polycab/Havells.

Supply and fix Thermal Magnetic release, MCCB 400 Amps 415 Volts, 4 pole 35 KA, Ics=100% Icu, adjustable overload 80-100% and adjustable short circuit 5-10 In complete all as specified and directed. Make C&S Cat No CSE3S400ATM4P-* or equivalent in HPL/Indo Asian.

Supply and fix Thermal Magnetic release, MCCB 250 Amps 415 Volts, 4 pole 50 KA, Ics=100% Icu, adjustable overload 80-100% and adjustable short circuit 5-10 In complete all as specified and directed. Make C&S Cat No CSE2N250ATM4P-* or equivalent in HPL/Indo Asian.

Supply and fix Thermal Magnetic release, MCCB 160 Amps 415 Volts, 4 pole 25 KA, Ics=100% Icu, adjustable overload 80-100% and adjustable short circuit 5-10 In complete all as specified and directed. Make C&S Cat No CSE2M250ATM4P-* or equivalent in HPL/Indo Asian.

Supply and fix Thermal Magnetic release, MCCB 125 Amps 415 Volts, 4 pole 25 KA, Ics=100% Icu, adjustable overload 80-100% and adjustable short circuit 5-10 In complete all as specified and directed. Make C&S Cat No CSE1M125ATM4P-* or equivalent in HPL/Indo Asian.

Supply and fix Thermal Magnetic release, MCCB 100 Amps 415 Volts, 4 pole 25 KA, Ics=100% Icu, adjustable overload 80-100% and adjustable short circuit 5-10 In complete all as specified and directed. Make C&S Cat No CSE1M125ATM4P-* or equivalent in HPL/Indo Asian.

Supply and fix Thermal Magnetic release, MCCB 75/63 Amps 415 Volts, 4 pole 25 KA, Ics=100% Icu, adjustable overload 80-100% and adjustable short circuit 5-10 In complete all as specified and directed. Make C&S Cat No CSE1M125ATM4P-* or equivalent in HPL/Indo Asian.

Supply and fix Street light timer switch digital type in sheet metal enclosure 40 Amp 3 pole and neutral complete in all respect complete all as specified and directed. Indo Asian Cat No TL04ODBO or equivalent in Havells/Polycab.

Supply and fix on load Change over switch 63 Amp, 4 pole in sheet metal enclosure complete all as specified and directed. Indo Asian Cat No ITAS0063 or equivalent in Havells/C&S.

Supply & fix pole box of new technology made up of Thermoplastic Polycarbonate Pole box, install, testing and commissioning of Thermoplastic Polycarbonate Pole box which is shock, rust, dust, impact and water proof, halogen and silicon free, UV resistance with internally embedded gasket high grade gasket made of polyurethane. The thermoplastic pole box suitable size with degree of protection IP 65, type tested, system voltage – 230V , 50Hz, Capacity with temperature resistance of -40°C to 120°C, with cable entry ,suitable size of Glands, all as specified and duly mounted on steel tubluar pole with suitable MS flat with bolts nuts and washers complete including supply fixing and making provision of the following :- (a) MCB SPN 30/32 Amp.

Supply and fixing 3 core copper flexible cable FRLS 1.5 Sqmm size, 1100 volts grade complete all as specified and directed

Supply and fix in replacement of unsv driver for 45/60 Watt LED street light fitting as existing complete all as specified and directed

Supply and fix in replacement of unsv PCB for 45/60 Watt LED street light fitting as existing complete all as specified and directed

Supply and fixing for steel tubular swaged poles complete with cast iron base plate,finial tapper plug, bolts, nuts and screws as specified type 410 SP-31 (9.00 metres long), erected to truly vertical position including one coat of red oxide primer and two coats of aluminium paint and making 30cm wide strips 5 Nos with white and black paint alternately on external surface above PCC benching/ground level including making pole identification number and figure with synthetic enamel paint of Ist quality and painting with bitumenous paint internally and externally for portion embedded in PCC. , complete all as specified, including taking down old poles of any type and removing from site.

Painting to existing steel tubular LT poles , 9m long including cross arms, channels, angle iron support, bracings, clamps etc. with two coats of aluminium paint superior quality of approved make on surface expose to view and making 30 cm wide strips (total 5 Nos) with white and black paint alternatively on external surface above PCC benching including prepration of old painted surface by scraping complete all as specified and directed.

Supply and laying for aluminium conductor, steel reinforced (ACSR) conductor for LT lines on steel tubular poles, stretching without kinks and bends including binding wire , jumpering , maintaining proper sag as per IE Rule including cutting of tree branches around the ACSR with in 5 mtr dia , complete all as specified of any size as directed by Engr-in-Charge, including taking down old conductor of any type , shape and size and removing from site.

Re-stretching of ACSR conductor and earth wire of any size and type on LT poles including disconnection and re-binding with insulators with suitable size of binding wire after re-stretching, connecting jumpers, adjusting line dividers etc complete all as directed by Engr-in-Charge.

Material and labour for structural steel work as in cross arms, bracings, supports, clamps and back plates fabricated from steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed by Engr-in-Charge and applying two coats of aluminium paint over one coat of red oxide zinc chrome primer including preparation of surfaces complete, and dismantling old cross arms and removing from site, complete all as specified.

Material and labour for stay assembly using stay rod of 20mm dia complete with accessories as shown in Electrical plate No 1 of SSR 2009 Part - I including galvanized steel stranded wire of size 7/ 4mm, loop type insulatorof size 65x90mm , including taking down existing stay complete all as specified and directed (loop type insulator, earth work and PCC shall be measured and paid for separately) .

Supply and fixing for loop type insulator procelain, vitreous, white, brown or green large size with over all dimensions 90 x 140mm clearance of hole 25.5mm for working pressure 1100 volts bolts, washers and nuts including taking down old insulators of any type , shape and size and removing from site complete all as specified and directed

Supply and fixing for pin type procelain, vitreous, white, brown or green insulator ,including galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut,100mm height, 65mm dia for working pressure 1100 volts,including taking down old insulators of any type , shape and size and removing from site complete all as specified and directed

Supply and fixing for shackle type procelain, vitreous, white, brown or green insulator for working pressure 1100 volts of 90mm dia and 75 mm height ,including galvanised mild steel strips of 31 x3mm size including 12mm dia insulator bolts, washers and nuts , including taking down old insulators of any type , shape and size and removing from site complete all as specified and directed

Supply and fixing for G.I earth wire 4mm dia, on LT poles for continuous earth wire, stretched without kinks, bends and binding with wire and fabrication of cradles hexagonal / rectangular guards etc , including taking down old wire of any type , shape and size and removing from site complete all as specified and directed

Supply and laying for 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheating of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire one twin core cable flat or circular single stranded conductor size 10 Sqmm , including taking down old cable complete all as specified and directed

Supply and fixing LT line PVC spacer suitable for 05 and 04 wires or as per sample complete all as specified and directed

Trimming of trees and cutting of tree branches carefully upto 3 mtr clear distance from wire/cables/conductor/panel boards along LT over head electric line using all required safety equipment for each Span of approx 40 metre length complete all as specified and directed

M&L for repair and refixing of panel board door by welding or by nut and bolt including hinges reqd and spray painting with synthetic enamel paint two coat over one coat of red oxide primer complete all as specified and directed.

Supply & fix busbar box, installation, testing and commissioning of factory fabricated prewired bus bar, cubical type IP 65 of suitable size out door, double door, dust and vermin proof, CPRI approved made out of 50x50x6mm angle iron frame/legs and 3.15 mm thick CRCA sheet with openable shutters on both sides (front & rear), powder coated externally and internally, having locking arangement mounted on four legs 90 cm high (30 cm below ground level and 60 cm above ground level), embedded in PCC (1:2:4 ) type B2 of suitable size with clear working space all around the bus bar complete all as specified & directed by the Engr-in-Charge to accommodate the following accessories :- Incoming (a) MCCB 160 Amp FP, 25 KA-01 Nos (Make : C&S Cat No CSE2M250ATM4P-* (b) Digital multi functional Panel meter showing V/I.Fq, PF along with CTs , Make:-C&S/Schneider/ Indoasian/ - 01 Set (c) Indicators lamp LED type RYB 240 volts - 01 Set. Outgoing MCCB 40/32 Amp FP, 25 KA-05 Nos (Make : C&S Cat No CSE1M125FMU4P-* MCB 32 Amp SPN-02 Nos (One Spare), (Make : C&S Cat No CSMBS1C32N) (b) Copper bus bar 200 A for three phase and neutral duly insulated with sleeves of colour RYB with necessary holes for looping the circuit for outgoing circuit. (Note : (i) Incoming and outgoing cable shall be fixed with appropriate size of copper thimble. (ii) Apron shall be provided at bottom for protection of cable to avoid entry of vermins, reptiles. (iii) Entries of all sizes of cables in panel should be done through adequate size of metallic cable glands.

Supply and replacement LED flood light fitting 30 watt SMD with pressure die cast aluminium housing complete with all accessories with suitable size of clamp and mounting bracket and electronic driver with GI tubing of suitable size as required at site, testing & commissioning complete all as specified and directed. Make : C&S Cat Part No LTEF130WHPLED or equivalent in Polycab/Havells.

S&F Digital panel meters 3 phase voltage meter accuracy class 1 complete in all respect including suitable wiring and connection including taking down unsv all as specified and directed by Engr-in Charge. Make C&S Cat No CSM-A-V3-S1 or equivalent in Polycab/Havells.

S&F Digital panel meters 3 phase ammeter accuracy class 1 complete in all respect including suitable wiring and connection including taking down unsv all as specified and directed by Engr-in Charge. Make C&S Cat No CSM-A-13-S1 or equivalent in Polycab/Havells.

Material and labour for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level connecting to the Galvanized strip 32x6 mm as earthing lead by means of bolts, nuts check nuts and washers of galvanized iron and steel strip protected by provision of GI light grade pipe 40mm bore including provision of concrete pit made in PCC 1:2:4 type B-1 with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 kg/sqm) and frame of angle iron 25 x 25 x 6 mm with lugs 2 Nos and handle of 6 mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering performed at bottom, 1.75 metre long place on top edge of earth plate, common salt & charcoal filling, test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance of not exceeding 50 metres all as per electrical plate No. 3 of SSR 2009 Part-I and connecting to earth test points all as specified including testing on completion.

Supply and fix Copper bus bar of size 50x6 mm flat for three phase and neutral (Total 04 Nos) length of 25 to 38 cm each as site requirement) and connected items complete for smooth functioning including taking down old unsv bus bar from panel board complete all as specified and directed

Operation & Maintenance of 11 KV sub station including equipment (transformers, gang operating devices, panel boards) and other safety equipments installed at electrical receiving station by providing one skilled electrician each in two shifts of eight hour per shift, per day at receiving station cum sub station complete all as specified and directed. Note:- Man power to be employed are as under:- (i) Electrician (Skilled) - 01 No. in Each shift. (ii) The provision of statutory laws relating to minimum wages shall be strictly adhered by the contractor and the quoted rate shall be deemed to include these factors. If the quoted rates are less than the minimum fair wages the bid shall be treated as non-bonafide.

Operation & Maintenance of 11 KV sub station including equipment (transformers, gang operating devices, panel boards) and other safety equipments installed at electrical receiving station and operation & maintenance of diesel generating set at 9 ASC by providing one skilled electrician each in one of eight hour per shift, per day at receiving station cum sub station. Note :- DHPP for DG Set Shall be issued by department under schedule 'B' free. Note:- Man power to be employed are as under:- (i) Electrician (Skilled) - 01 No. in Each shift. (ii) The provision of statutory laws relating to minimum wages shall be strictly adhered by the contractor and the quoted rate shall be deemed to include these factors. If the quoted rates are less than the minimum fair wages the bid shall be treated as non-bonafide.

Supply only (Calcium based granular disinfectant for chlorination for water treatment, in Bbsr under AGE E/M GOS, GE (I) GOS in plastic drums of 45 kg/each drum complete all as specified and directed. Make : Aquafit or equivalent as approved by E-in-Cs Branch.

Supply only alum crystal for water sedimentation complete all as specified and approved by GE.

Cleaning of over head water storage tank of capacity 20000 gallons by dewatering existing water and removing all dirt silt vegetation formation on side walls/stair inside and bottom cleaning with wire brush to remove settled materials and cleaning with clean water and applying lime washing two coats inside the tank including re-writing the date of cleaning capacity of the tank/sump with synthetic enamel white paint on black base complete (ii) Cleaning the surrounding area of the reservior to a distance of 2 mtrs circumferance including cutting of grass digging out roots filling holes and levelling around and removing waster materials to a distance not exceeding 20 mtrs complete and all as directed by Engineer in charge of following capacity of water supply installation. Note : Periodicity for cleaning of tanks shall be twice in contract period as directed by Engineer in Charge (ii) Every cleaning shall be measured as each job

All as per item No 57 above but of capacity 10000 gallons complete all as specified and directed.

M&L for two coats of cement base paint including taking down of existing treatment for semi under ground sump/reservoir of capacity of 20000 galns storage, complete all as specified and directed by Engineer in charge.

All as per item No 59 above but the capacity 10000 gallons complete all as specified and directed.

Surface dressing not exceeding 15 cms deep in soft/loose soil including removal of bricks/stone pieces herbs, shurbs and vegitation complete once in six months complete all as specified and directed.

Supply and replacement 3 m long column pipe 80 mm / 50 mm dia as per site requirement with both ends flanged or socket fix in ground/above ground inside borewell etc alongwith complete fittings including dismantling of the unsv column pipe/GI tubing, all as specified and directed.

Wash of borewell with compressor machine approx 6 hrs continuous in 3 times in a day with 3 hours gap, cleaning of entire row of borewell till receiving of clean water, replacement of submersible cable 10x3 core copper flat flexible from DOL Starter to underground submersible pump rewinding submersible pump by super enameled copper wire, inusation and warnishing, wornout ball bearing required for pump, hanging on rope from submersible pump to submersible stand, replacement of submersible cover of 300x300X10mm complete in all respect complete all as specified and directed.

MCC MECHANICAL AND ENGINEERING CORPORATION

chauhan syndicate

M/s Bapujee Builders and Traders

M/S Vimal Enterprise

M/s Ats Electricals

M/S. KISHAN ENGINEERING