SPL REPAIR TO ROOF FALSE CEILING AND MISC CONNECTED WKS TO BLDG NOS SL-12A AND 12A1(CH), SL-12A2 (DH), CMH-71A (OFFRS MESS SERVANT QTRS), DINING HALL BLDG NO SL-30, SPL REPAIR/REPL OF CONVERSION SOLAR STREET LIGHTS AT MT ABU UNDER AGE (I) UDR

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and jointed in any mortar. Complete all as specified and directed by Engr-in-charges.

Material and labour for 25 mm thick PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as a levelling course in floor Complete all as specified and directed by Engr-in-charges.

Material & Labour for machine cut Kota stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and mirror polishing with over and including 15mm thick screed bed in cement mortar (1:6) for floor finishes, Complete all as specified and directed by Engr-in-charges.

Material and labour for 20-25 mm thick machine cut kota stone salb in skirting, risers of steps and pillars of size not less than 300x150 mm over and including plaster 10 mm thick in cement mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl rubbing and mirror polishing Complete all as specified and directed by Engr-in-charges.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises Complete all as specified and directed by Engr-in-charges.

M & L for Virified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inclding 15 mm thick screed bed in cement mortar (1:6) Complete all as specified and directed by Engr-in-charges.

Material & Labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and inted in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 Complete all as specified and directed by Engr-in-charges.

M&L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7/ 300x600mmx7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick rendering in cement mortar 1:4 , on fair faces of brick work or concrete surfaces as backing Complete all as specified and directed by Engr-in-charges.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. Complete all as specified and directed by Engr-in-charges.

Material and labour for 10 mm thick rendering in cement mortar 1:3 on concrete surfaces of ceiling, finished even and smooth without using extra cement Complete all as specified and directed by Engr-in-charges.

Material and labour for preparation of newly plastered surface of ceiling and applying three coat of white wash Complete all as specified and directed by Engr-in-charges.

Material and labour for 10 mm rendering in cement mortar 1:6 on other than fair faces of brick wall surfaces finished even and smooth without using extra cement. Complete all as specified and directed by Engr-in-charges.

Material and labour for 15 mm thick rendering in cement mortar 1:4 using water proofing compound @ 2% by weight of cement on other than fair faces of brick wall surfaces, finished even and smooth without using extra cement Complete all as specified and directed by Engr-in-charges. Note :- water proofing compound shall be measured and paid seperately.

Supply only integral water proofing compound, ISI marked. Complete all as specified and directed by Engr-in-charges.

M & L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer Complete all as specified and directed by Engr-in-charges.

Material and labour for preparation of newly plastered surface of walls and applying of two coats of oil bound distemper over a coat of 1 mm thick Birla white care putty etc. Complete all as specified and directed by Engr-in-charges.

Taking down wooden frame with shutter without taking off shutter from the frame, n-exceeding 1.50 sqm each including removing from site. Complete all as specified and directed by Engr-in-charges.

Taking down wooden frame with shutter without taking off shutter from the frame exceeding 1.5 sqm each but n-exceeding 4 sqm each including removing from site. Complete all as specified and directed by Engr-in-charges.

S & F for 125x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed Complete all as specified and directed by Engr-in-charges.

S&F for factory made 35mm thick 2nd class hard word plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated Complete all as specified and directed by Engr-in-charges.

Supply and fixing of 35 mm thick, factory made, gauged and skeleton shutters from 2nd class hardwood (hollock), open rebated, prepared to receive gauge, glass etc (without sash bars), edges of framing plain, chaimfered or rounded, fitted with cut & mitred beads for securing glass, guage etc, size of members of shutters as specified in SSR Part-I, members kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F solid PVC frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet & edges will be printed to match with prelam sheet rein forced with MS square tube etc. Complete all as specified and directed by Engr-in-charges.

S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site & drawing Complete all as specified and directed by Engr-in-charges.

Material and labour for preparation of new wooden surface of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of approved shade over a coat of pink primer Complete all as specified and directed by Engr-in-charges.

Supply and fixing of MS butt hinges, medium weight, cold rolled of size 100 mm. Complete all as specified and directed by Engr-in-charges.

Supply and fixing butt hinges extruded aluminium alloy with galvanised mild steel hinges pin, anodised 100 mm size fixed to PVC frames Complete all as specified and directed by Engr-in-charges.

S & F aluminium alloy, anodised, sliding door bolt of length 250 mm with hasp and staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy. Complete all as specified and directed by Engr-in-charges.

S & F aluminium anodised barrel tower bolt of extruded section 200 mm long. Complete all as specified and directed by Engr-in-charges.

S & F 150 mm size aluminium handles, cast type anodised. Complete all as specified and directed by Engr-in-charges.

S & F aluminium anodised handle cast type 100 mm long. Complete all as specified and directed by Engr-in-charges.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided. Complete all as specified and directed by Engr-in-charges.

M & L for 50 mm thick PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) laid in alternate bays as in plinth protection incuding finished the surface even and fair without using extra cement Complete all as specified and directed by Engr-in-charges.

M&L 75 mm thick cement concrete C2 (1:3:6) using 40 mm graded aggregate as in sub base of floor Complete all as specified and directed by Engr-in-charges.

S&F Chequered cement concrete tiles 30cm X 30cm x 25mm thick set, jointed and pointed in neat cement slurry in floors with grey cement and pigments including 15mm thick screed in CM 1:4 Complete all as specified and directed by Engr-in-charges.

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work and precast concrete articles Complete all as specified and directed by Engr-in-charges.

M & L for brick work with sub class 'B' bricks (old size) stright or curved on plan exceeding 6 mtr mean radius built in CM 1:6 Complete all as specified and directed by Engr-in-charges.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position Complete all as specified and directed by Engr-in-charges.

Material and labour for RCC (1:1.5:3) type A0, using 12.5mm graded stone aggregate as in chajjas, lintels, roof ceiling drops etc. Complete all as specified and directed by Engr-in-charges.

Material and labour for mild steel TMT bar 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90 mm dia or securing with clips Complete all as specified and directed by Engr-in-charges.

Material and labour for mild steel TMT bar 5 mm dia and over and upto and including 10 mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90 mm dia or securing with clips Complete all as specified and directed by Engr-in-charges.

Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick on rough finished surface of concrete in flat (Horizontal or sloping) Complete all as specified and directed by Engr-in-charges.

Use and waste of Formwork to chullah hoods, chajjas, troughs and similar items including edges on rough finished surface of concrete in flat Complete all as specified and directed by Engr-in-charges.

Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia Complete all as specified and directed by Engr-in-charges.

Supply & fixing in repair of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia Complete all as specified and directed by Engr-in-charges.

Supply & fixing in repair of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods Complete all as specified and directed by Engr-in-charges.

S & F in repair vitreous china wash hand basin, white flat back of size 550 x 400 mm including bracket. Complete all as specified and directed by Engr-in-charges.

S & F in repairs 10 litre PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and all fittings and connections Complete all as specified and directed by Engr-in-charges.

Supp and fixing in repair brass chromium plated head shower with revolving joint and 150 mm long shower. Complete all as specified and directed by Engr-in-charges.

Supply and fixing in repair, brass chromium plated tubular towel rail, 20 mm dia, 'D' type, 60 cm long between flange fixed Complete all as specified and directed by Engr-in-charges.

Supply and fixing in repair pillar taps cast copper alloy with capstan heads, chromium plated, fancy type of size 15 mm bore screwed down, high pressure, with or without lettered "Hot" or "Cold" with long screwed shanks and flynut, screwed for 15 mm iron pipe and fixed. Complete all as specified and directed by Engr-in-charges.

Taking up or down GI water tubing with fittings including or removing from site of size 15 mm bore. Complete all as specified and directed by Engr-in-charges.

- ditto - but 20 mm bore Complete all as specified and directed by Engr-in-charges.

S & F of GI water tubing, medium grade with fittings, fixed to wall and ceiling or laid in floor of size 15 mm bore. Complete all as specified and directed by Engr-in-charges.

- ditto - but 20 mm bore Complete all as specified and directed by Engr-in-charges.

Supply and fixing in repair Stop valves, fancy type chromium plated with long shank and cup (concealed type),15 mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed Complete all as specified and directed by Engr-in-charges.

S&F in repair for 15mm bore stop valve (angle valve), cast copper alloy chromium plated screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, Complete all as specified and directed by Engr-in-charges.

Supply and fixing in repair, fancy type bib taps, 15mm, cast copper alloy, chromium plated, with crutch or butterfly hande screwed down, screwed for iron pipe or for brass ferrule and fixed, concealed of size 15 mm bore Complete all as specified and directed by Engr-in-charges.

Dismantling of water tanks of capacity exc 250 and not exc 500 ltr and removing from site. Complete all as specified and directed by Engr-in-charges.

Supply and fixing of rotational moulded HDPE water storage tank 1000 ltrs capacity (cylindrical vertial with closed top) double layered, ISI marked, hoisted and fixed in position Complete all as specified and directed by Engr-in-charges.

Supply and fixing of ball valve, high pressure with polythene float and flynut, screwed for iron pipe or brass ferrule of size 20 mm bore Complete all as specified and directed by Engr-in-charges.

S & F in repair glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated brackets guard and railing 60 cm long Complete all as specified and directed by Engr-in-charges.

S&F in repair for vitreous china urinals, half stall type Aqua Seal Premium quality including flush pipe of chromium plated brass tube(speader) Complete all as specified and directed by Engr-in-charges.

Supply and fixing in repair Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes and bed concrete etc Complete all as specified and directed by Engr-in-charges.

S&F in repair brass CP soap dish incl brass CP screws and wooden cleats complete all as specified and directed by Engr-in-Charge.

S & F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors Complete all as specified and directed by Engr-in-charges.

S & F 75mm PVC (SWR) bends any radius Complete all as specified and directed by Engr-in-charges.

Demolition of AC/CI pipe of 100 mm dia, set in cement mortar, fixed in any position. Complete all as specified and directed by Engr-in-charges.

Demolition of AC/CI pipe of 75 mm dia, set in cement mortar, fixed in any position Complete all as specified and directed by Engr-in-charges.

S&F PVC (SWR) 110mm bore pipes, single socketed, in any length with rubber ring joints laid in floors or trenches jointed in cement mortar Complete all as specified and directed by Engr-in-charges.

M&L for 110mm bore PVC (SWR) bend, provided with access door, Complete all as specified and directed by Engr-in-charges.

Supply and fixing of 75 mm CI Nahani trap with PTMT gratings (minimum weight 250 gm) including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 Complete all as specified and directed by Engr-in-charges.

S & F in repairs 32 mm PVC waste pipe for wash basin, 600 mm long Complete all as specified and directed by Engr-in-charges.

S & F in repair PVC connections 45 cm long including 15 mm bore PTMT nuts on both ends Complete all as specified and directed by Engr-in-charges.

Removal of old water proofing treatment any Nos of layers and of any description, incl demolition and or taking off PCC padding/plaster on RCC slab, also including removing of bitumen coating to show the concrete surface to its true colour and roughening etc Complete all as specified and directed by Engr-in-charges.

M & L for the surfaces which are to receive the coating or treatment, must be free from oil, laitance, grease, wax, dirt or any other form of foreign material adhering on it before the waterproofing job started. Dust free the surface, including removing of existing treatment/ old felt / loose plaster / concrete etc. and repair with polymer mortar by adding bonding agent (SBR). Repairing of slab, parapet wall junction, cracks and other large blowholes by open in “V” shapes & filling by polymer mortar or putty followed by fiber mash tape with SBR in conjunction with cement. Complete all as specified and directed by Engr-in-charges.

M & L for POLYURETHANE BASED ELASTOMERIC OVERLAY SYSTEM FOR ROOF TREATMENT: “M & L for providing and applying polyurethane liquid applied roof waterproofing with improved water ponding capability, thermal insulating elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 60% and Solar Reflectance Index 106 as per (ASTM E1980-19) / tear strength ~20 N/mm (Free film, 14 days, +30 °C) (ASTM D624) and Tensile adhesion strength-≥ 1.5 N/mm2 (ASTM D4541) Complete all as specified and directed by Engr-in-charges.

Supply and fixing of stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apertaure 1.4 mm and fixed with tinned tacks, galvanised wire, screws fixed to aluminium grills or wooden frame etc Complete all as specified and directed by Engr-in-charges.

S & F 3.5 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane Complete all as specified and directed by Engr-in-charges.

Supply & fixed steel windows/ventilators box type ERW hollow 'P' section comprising double frame including gauged and glazed skelton shutter 30mm thick jointed internally with flat iron 25x3mm complete including hinges handle tower bolts, stops lugs,grill etc all as shown in drawing CEJZ/TD/20 sheet 1/3 to 3/3 and CEJZ/TD/24 sheet 1/3 to 3/3 as applicable Complete all as specified and directed by Engr-in-charges. Note :- For the purpose of measurement & payment double shutter with frame and grill shall be considered as one unit. (ii) Glazing,wire mesh & painting shall be measured & paid separately.

M&L two coat of syntetic enemel paint over new steel surface of any description over 10cm in width or grith not otherwise described over one coat red oxide primer incl preparation of surfaces Complete all as specified and directed by Engr-in-charges.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering Complete all as specified and directed by Engr-in-charges.

S & F prepainted 0.50 mm thick galvalume aluminium zinc AZ-150 coating GI based corrugated steel coloured Sheet having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping at aliternate corrugation screws as spd etc. Complete all as specified and directed by Engr-in-charges.

-Ditto- all as per item 02 above but except sheeting (any thickness). Complete all as specified and directed by Engr-in-charges.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws Complete all as specified and directed by Engr-in-charges.

Dismantling wrought iron or mild steel work of any description not otherwise provided for Complete all as specified and directed by Engr-in-charges.

M&L for rolled mild steel sections in rafters, purlins and posts or hollow square pipe as in tiles battens/ purlins, nut bolts etc . where connected to common rafters and runnuing rails fixed with angle cleats or other connecting plates and nut, bolts etc. confirnimg to Fe-290 (Gde E-165). Complete all as specified and directed by Engr-in-charges.

Material and labour for framed work Fe 410-W (Grade - E-250) as in door or gates of angle or other section with gusset plates, rails, braces, etc. complete drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings. Complete all as specified and directed by Engr-in-charges.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets. Complete all as specified and directed by Engr-in-charges.

Suspended false ceiling system using Chicago metallic (E - grid) exposed suspended system, grid size 600mm x 600mm compressing of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick (Thickness comprising of GI/0.4 mm+ PPPCGS/0.3 mm & weight of runner 1.35 kg for 3600 mm length), Cross Tee of dimensions 29mm x 24mm x 0.8mm thick (Thickness comprising of GI/0.4mm + PPPCGS/0.3mm & weight of Tee 0.195 kg for 600mm length) and Wall angle of dimensions 22.2mm x 22.2mm x 0.65mm thick (Thickness comprising of GI / 0.35mm + PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length) with and including 4mm thick HPSC (High pressure steam cured) pre primed, self embossed, textured designer board to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), with provn of light fixture Complete all as specified and directed by Engr-in-charges.

M&L rendering 15 mm thick in cement mortar 1:6 on walls, surface finished even & smooth without using extra cement etc. Complete all as specified and directed by Engr-in-charges.

Supply and fixing anodised aluminium powder coated door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. Complete all as specified and directed by Engr-in-charges. Note: minimum thickness of powder coating 50 micron.

Supply and fixing anodised aluminium window and ventilator shutters,powder coated side hung / sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) Complete all as specified and directed by Engr-in-charges.

Supply & Fixing 5.5 mm thick sheet glass, ordinary quality plain or tinted and glazing with rubber gasket in square not exceeding 0.5 Sqm in each pane, Complete all as specified and directed by Engr-in-charges.

Material & Labour for Virified Ceramic tiles, dark shade, 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with including 15mm thick screed bed or bedding layer with CM 1:4 Complete all as specified and directed by Engr-in-charges.

M&L Light shade Vitrified tiles 9-10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, laid over and including 10mm thick rendering in CM(1:3) in dados /skirting jointed in neat cement slurry & pointed in white or coloured cement to match Complete all as specified and directed by Engr-in-charges.

Material and labour for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, laid over a screed bed of 20 mm thick in CM 1:6 Complete all as specified and directed by Engr-in-charges.

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over 20 mm screed bed in CM 1:6 Complete all as specified and directed by Engr-in-charges.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; Complete all as specified and directed by Engr-in-charges.

Complete removal of existing surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots of walls Complete all as specified and directed by Engr-in-charges.

M&L two coats of oil bound distemper (acrylic) white or tinted over and including 3mm thick wall care putty including preparation of new or old plastered surfaces of walls etc. Complete all as specified and directed by Engr-in-charges.

Material and labour for preparation of newly/old plastered surface of wall and applying two coats of plastic emulsion incl 3mm thk wall care putty Complete all as specified and directed by Engr-in-charges.

M&L for one coat of synthetic enamel paint on old painted steel surfaces of any description over 10 cm in width or girth including preparation or surfaces Complete all as specified and directed by Engr-in-charges.

Demolition of reinforced cement concrete in ground floor and paving n. exc. 15cm thickness (below or above ground level) Complete all as specified and directed by Engr-in-charges.

M&L for providing precast cement concrete Type B1 1:2:4 (20mm graded aggregate)as in cover slabs etc of any size and thickness as required Set in cement mortar 1:4 Complete all as specified and directed by Engr-in-charges. Note :- Reinforcement will be measured and paid saperately

Taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each and re-fixing in the same opening after repaired Complete all as specified and directed by Engr-in-charges.

Forming embankments including raising (or lowering) earth, solid, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., exc 1.5m high from base Complete all as specified and directed by Engr-in-charges.

Material & Labour for vitrified light coloured tiles 8-9mm thick (square or rectangular) polished, area of each tiles not exc. 0.36 sqm, in floors etc. set and jointed with cement mortar and pointed in white or coloured cement to match over and with including 15mm thick screed bed or bedding layer with CM 1:4 Complete all as specified and directed by Engr-in-charges.

Material and labour for 300x300x20-25mm thick chequered cement concrete tiles (rubberised moulded) with grey cement and pigment set, jointed and pointed in neat cement slurry including laid over a screed bed of 20mm thick in CM 1:6 complete all as specified and directed Engr-in-charge.

Taking down carefully aluminum/copper point wiring (light/fan/socket/power) complete including fittings such as switch, socket, ceiling roses light fittings etc and and making good disturbed surface of wall Complete all as specified and directed by Engr-in-charges. (Serviceable light fitting to be kept separately for re-use).

M&L for point wiring 1.5 Sqmm nominal area PVC insulated and unsheathed multistranded copper conductor FRLS in PVC concealed concuit with suitable metal box and hylem sheets with multistranded insulated solid copper earth continuity conductor of size 1.5 sq mm complete all as specified and directed by Engr-in-Charges.

(a) One light point controlled by one switch one way

(b) One fan/exhaust fan point controlled by one switch one way

(c) One socket out let 5 Amps 5 pin on independent board

(d) One socket out let 5 Amps 5 Pin on same board with other switch

All as per item No 2 here in before but with cable size 2.5 Sqmm for one 5 pin 15 Amps socket out let on independent board and multistanded insulated solid copper earth continuity conductor of size 1.0 Sq mm Complete all as specified and directed by Engr-in-charges.

S&F switch piano flush type 5 Amps single pole one way. Complete all as specified and directed by Engr-in-charges.

S&F socket out let 2 in 1 multi pin 5 Amps flush type universal. Complete all as specified and directed by Engr-in-charges.

S&F switch socket combination 2 in 1, multi pin 5 Amps flush type universal. Complete all as specified and directed by Engr-in-charges.

S&F switch socket combination 2 in 1, multi pin 5 Amps/15 Amps flush type universal. Complete all as specified and directed by Engr-in-charges.

S&F Ceilling rose on PVC board size 65 X 50 mm three terminal Complete all as specified and directed by Engr-in-charges.

S&F Angle holder backelite Complete all as specified and directed by Engr-in-charges.

S&F fan regulator electronic step type, 230 volt , 50 Hz Complete all as specified and directed by Engr-in-charges.

S&F MCB single pole, Curve 'C' 240 volts 5 to 32 Amps Complete all as specified and directed by Engr-in-charges.

S&F MCB single pole and neutral, Curve 'C' 240 volts 32 Amps Complete all as specified and directed by Engr-in-charges.

S&F MCB single pole and neutral, Curve 'C' 240 volts 40 to 63 Amps Complete all as specified and directed by Engr-in-charges.

S & F MCB DB SPN 12 way (double door) with 200 Amps rated bas bar, neutral link, earth bar and Din rail Complete all as specified and directed by Engr-in-charges.

S&F LED LED light fittings 1x18 watt, 220 volt, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductore cable of suitable size from ceiling rose Complete all as specified and directed by Engr-in-charges.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size Complete all as specified and directed by Engr-in-charges.

Taking down carefully, deposited to MES store and hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fanHanging only ceiling fan (M.D. supply) complete all as specified and directed by Engr-in-Charge.

M&Lfor sub main wiring with PVC insulated and unsheathed 2x4 Sq mm single core multistrandred copper conductor cable passing through in and including PVC conduit , concealing in walls (by means of chasing including making good existing surface and matching existing surface ) ISI marked and conduit accessaries fixed on surface of wall, ceiling etc, making good the distrurbed surface, incl 2.5 Sq mm single core copper conductor cable PVC insulated and unsheathed as earth wire. complete all as specified and directed by Engr-in-charge. Note :- Two runs of cable 4 Sqmm and One run of 2.5 Sqmm along with conduit shall be measured as one unit length.

Supply and Fixing LED Bulb 12 Watt Complete all as specified and directed by Engr-in-charges.

Supply, laying and testing electric under ground XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross-sectional area 16 sq. mm 2 Core. Complete all as specified and directed by Engr-in-charges.

S&F LED security light luminaries of 25 watt for energy saving having IP-65 degree of protection made of pressure die cast aluminum housing and heat resistant thoughned glass with excellent thermal management, LED's should have better optics and uniform distribution of light including GI tubing 40mm dia light grade 1.2 mtr long pipe bent to shape 120 degree for mounting of security light and fixed to wall/pole, with suitable MS clamps 2 Nos with nut and bolt and washers including connecting complete including 2.5 sqmm stranded copper conductor of suitable length Complete all as specified and directed by Engr-in-charges.

M&L for Earthing complete with GI steel earth plate eletrode 60 cm X 60 cm X 6.3mm thick barried directly in ground vertically to a depth not less than 2.25 metres below ground level with top edge of earth plate at a depth not less than 1.5 metres below level ground,connected to Gl iron or steel earth wire 4 mm dia (8 SWG) by means of nuts,bolts checks nuts and washers made of Gl iron or steel earth wire protected by Gl iron pipe 15 mm bore, medium grade and connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6:) type C1, pre-cast RCC coverslab 30 cm X30 cm X 10 cm with one lifting handle made of 8 mm dia ms bar funnel wire mesh,20mm bore GI or steel pipe medium grade for watering, charcoal or coke and salt in alternate larges,necessary excavation and earth work in any type of soil complete all as shownin electrical plate No 3 of MES schdule part-I and testing after completion Complete all as specified and directed by Engr-in-charges.

Excavating in trenches n.exc 1.5 m width and n.exc 1.5m in depth for taking out cable and cable cover and getting out in any type of soil Complete all as specified and directed by Engr-in-charges.

Returning, filling in, including spreading levelling, watering and well ramming in layers n.exc 25 Cm. Complete all as specified and directed by Engr-in-charges.

Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5 m above the starting point Complete all as specified and directed by Engr-in-charges.

M&L for spreading, levelling in layers n exc. 25 cm thick and ramming of sand cushioning to PVC/ XLPE cables with tibba sand and punning to provide required cover to UG cables. Complete all as specified and directed by Engr-in-charges. Note :- For the purpose of payment only punned thickness will be measured.

Supply and laying reinforced precast concrete cable cover, class LV, type 1 flat, 250mm x 150mm x 40mm. Complete all as specified and directed by Engr-in-charges.

Taking out old unserviceable protection pipe and supply and fix medium grade 50 mm dia GI pipe fix complete to wall , poles etc with suitable clamp for protection of cable Complete all as specified and directed by Engr-in-charges.

Taking down old unsv exhaust fan and Supply and fixing PVC frame exhaust fan with lover shutter of size 150mm sweep 1280 RPM, air delivery 520 CMH, power input 28 W single phase 240 Volts connected Complete all as specified and directed by Engr-in-charges.

M&L MCB TPN DB comprising of sheet metal enclosure double door suitable for mounting MCB 415 Volts 4 way including dismantling old one. Complete all as specified and directed by Engr-in-charges.

S&F MCB TPN 63 Amps 415V 10KA 'B' curve miniature circuit breaker (MCB) and current carrying capacity in the DB complete with connection testing and commissioning. Complete all as specified and directed by Engr-in-charges.

S & F sheet metal enclosure with socket plug top and MCB 20amp 240v Complete all as specified and directed by Engr-in-charges.

Supply, laying and testing electric under ground XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross-sectional area 35 sq. mm 3.5 Core. Complete all as specified and directed by Engr-in-charges.

30. Supply and Fixing LED Bldg security light fitting 35 Watt 230 Volt outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, GI bracket with impact and corrosion resistant including thermal management in multiple optice complete with IP 65/66 protection Complete all as specified and directed by Engr-in-charges.

30. S&F Bulk head fitting plastic body for exterior wall Complete all as specified and directed by Engr-in-charges.

Taking down carefully old LED street light alongwith bracket, nut, bolt, washers etc from existing electrical pole of any type/any cap and deposited to MES store. Complete all as specified and directed by Engr-in-charges.

Supply , installation and testing of “Lithium based Energy Efficient Integrated Solar Street Light of 40Watt” in Single FRP body with duly Polyurethane coating (Camouflage color) , encases with Monocrystalline Solar PV Panel of 78/80Wp , Lithium Battery 11.1/12.8V, 39.6AH with inbuilt BMS, IP 65, High brightness W-LED(180-200lm/watt) lamp with Aluminum reflector for better light distribution , CRI >70, Color Temperature 5700K - 6500K, Microcontroller based charge controller cum driver, automatic dimming function ( first four hours at full brightness & rest of the time at lower light level with PIR Motion Sensor), Dusk to Dawn Operation, suitable to working temperature: (-) 20C to (+)55C, weight not more than 16-18kg with adjustable MS clamp suitable for pole/wall mounting etc complete as required. Protections: Short Circuit, overload, Reverse polarity and battery protections. Firm should provide Vital Parameters Test report from NABL accredited lab and should be of made in India with CE & ROHS compliant. Suitable for fixing on steel tubular pole and Wall as required Complete all as specified and directed by Engr-in-charges.