PROVN OF HARD STANDING FOR OPEN PARKING ALONGWITH ADEQUATE RAMP AND 04 X SECURITY LIGHTS FOR UNIT B VEHS AT MT AREA OF MH PANAGARH AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R-I UNDER GE PANAGARH

Amount

Excavation over areas n.exc 1.5m depth and getting out in soft/loose soil complete all as specified and directed

All as per item No 1.00 mentioned here-in-above but depth exceeding 1.5m complete all as specified and directed

M&L for Plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs complete all as specified and directed

M&L for 300 mm thick Kankar or laterite,with mix of fly ash ,clinker & stone dust in the proportion of 1:3:6 ( i.e. 10% fly ash,30% clinker & 60% stone dust ) laying in layers n.exc 10cm thick ,watering ,ramming and compacted with vibratory/power roller 8 to 12 tonn roller to required camber and gradient complete all as specified and directed by Engr-in-charge .

M&L for PCC (1:4:8) 100 mm thick Type D2 (using 40 mm graded stone aggregate) used as in sub base floor/pavings and finishing complete all as specified and directed.

M&L 150 mm thick PCC M-25 (design Mix) (using 20mm graded crushed stone aggregate) as in hardstanding laid in panels, finishing the surface even and finish the surface by brooming complete all as specified and directed. Note:(i) Material for PCC M-25 shall be carried out from RMC as approved by Engr-in-Charge (ii) Plate viberator to be used for compacting of floor (iii) Contractor shall furnished necessary test report of M-25 and purchase voucher of plant for this aspect before claiming of RAR. (iv) Quoted rates deemed to be included for necessary T&P, Transportation and plasticizer and nothing extra paid to this aspect.

M&L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete, all as specified and as directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade B complete all as specified

M & L for forming construction joint 45mm deep x 10mm wide filled with sealing compound, Grade 'B' complete all as specified and directed.

Surface dressing n.exc 15 cm deep in soft /loose soil complete all as specified and directed.

Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan andn exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

All as per item No 11.00 mentioned here-in-above but exc 1.5 m depth beyond the first 1.5 m complete all as specified and directed.

Moorum/red bajri filling in floors or in foundation, laid in layers n.exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore broken stone of gaugen.exc. 63mm, deposited, spread and leveliled in layersn.exc. 150mm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC type D2, 1:4:8 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in columns, pillars, piers, posts, and struts as desired complete as directed by Engineer in Charge.

M&L for RCC M-25 (Design Mix) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in chajjas and similar work complete all as specified & directed by Engineer in Charge

S&F Mild Steel TMT bars 10mm and over, cut to lenghth, bent to shape requird, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clip all as directed by Engineer in Charge.

All as per item No 20.00 mentioned here-in-above but 6mm to 8mm dia complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finihed surfaces complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams for rough finished surfaces etc complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces complete all as specified and directed.

M&L for formwork to chajja and similar work including edges for rough finished surfaces complete all as specified and directed.

S&F pre-painted galvatume aluminum zinc coating @ 150 GSM GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating @ 150 GSM GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F mild steelwk as in framed roof trusses, purlins, rails and fristing incl distances pieces, cleats etc conforming to Fe 410 - O or Fe 310 - O complete all as specified and directed.

S&F mild steel wind ties for roof including securing bolts complete all as specified and directed.

S&F mild steel screw bolts 5 to 10 cm long and 5 to 10 mm dia of shanks with hexagonal head at one end and screwed other with fitted nut and washers complete all as specified and directed.

S&F hangers 6 mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified and directed.

S&F anodised powder coated aluminium snap grid frame work for false ceiling (size of grid 605x605 mm ) complete all as specified and directed.

S&F non asbestos fibre cement designer building boards 6 mm thick fixed designer or laid/ inserted to timber/GI/Aluminium framework with screws in ceiling complete all as specified and directed.

M&L for two coats synthetic enamel paint over a coat of red oxide primer on new steel surfaces incl preparation of surfaces over 10 cm width or girth complete all as specified and directed.

M&L for 4mm thick plain sheet glass ordinary quality & glazing with oil putty n.exc 0.50 Sqm in each pane complete all as spd and directed by Engineer-In-Charge .

S&F stainless steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples complete all as specified and directed.

S&F factory made single extruded WPC ( Wood polymer composite) solid door/window and others frames/chowkhat of size 50x125 mm double shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed stainless screws having minimum frame density of 750kg/cum and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge.

S&F factory made single extruded WPC ( Wood polymer composite ) solid Plain flush door shutter of 30 mm size comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives having minimum density of 650kg/cum and with property of being termite/borerproof,water/moisture proof and fire retardent and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless screws complete as per direction of Engineer-in-charge.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dashfasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including aluminium snap beading for glazing/ paneling, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F powder coated anodised aluminium window shutters, sliding type without sash bars, (minimum thickness of powder coating 50 micron) for three track shutters of windows & ventilators aluminium sections weighing 0.55 kg/m including necessary joining cleats , Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, anodised aluminium fittings suitaible etc all complete as per architectural drawings and the directions of Engineer-in-charge.

M&L for framed work such as grills etc with ends of bars shouldered nd or riveed or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixe complete all as specified and directed by Engineer-in-charge.

S&F 100mm butt hinges, medium weight, cold rolled mild steel complete all as specified and directed

S&F 200mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 125mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed

S&F mild steel flat iron 25x6mm as in hold fasts including all necessary cutting etc complete all as specified and directed.

M&L for PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in bed block for fixing of hold fasts etc complete all as specified and directed.

M&L for 75mm thick Cement concrete type C-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base floor complete all as specified and directed.

M&L for Non - skid coloure joint free Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as complete all as specified and directed.including 15 mm thick screed bed or bedding layer in cement mortar (1:6) for laying wall tiles finishes (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engineer-in-charge)

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including CM (1:4) Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes and jointed with grey slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match all including screed bed or bedding layer of mortar 10 mm thick (1:3) for laying floor finishes complete all as specified and directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engineer-in-charge).

M&L for 40 mm thick Damp proof course in cement concrete type B-0, 1:2:4 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) using liquid water proofing compound as per manufacturer instruction on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note: WPC shall be measured and paid seperately)

Supply only liquid water proofing compound complete all as specified and directed. (Make : Pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

M&L for preparation of new surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar).

M&L for 75mm thick Cement concrete type C-1, 1:3:6 (using 20mm graded stone aggregate) as in plinth protection/path/pavement and finishing even and smooth without using extra cement complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall with clamps and jointed complete all as specified and as directed by Engineer-In-Charge.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soils complete all as specified and directed.

M&L for cement concrete Type C2, 1:3:6 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for machine pressed pre-polished precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and as directed.

E/M PORTION M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes/ modular, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

All as per item No 66.00 mentioned here-in-above but 5 Amp socket on same board with other switches complete all as specified and directed.

All as per item No 66.00 mentioned here-in-above but 5 Amp socket on Independent board with other switches complete all as specified and directed.

All as per item No 66.00 mentioned here-in-above but one bell point with other switches complete all as specified and directed.

M&L for wiring for socket outlet 3 pin, 15 amps on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes/ modular , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

M&L for wiring for socket outlet 3 pin, 15 amps on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor, PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

S&F ding dong, AC 230 Volts, single pole 230 volts complete all as specified and directed.

S&F bell push, flush type, 5 amp duly marked complete all as specified and directed.

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed.

S&F socket outlet 2 in 1 multipurpose 5 pin , (6 Amps ) flush type controlled by one switch duly marked complete all as specified and directed.

S&F switch 16 Amps, 230/240 V complete all as specified and as directed (For same board only)

S&F socket outlet 2 in 1, 6 pin, (16 Amps ) flush type controlled by one switch complete all as specified and directed.

S&F ceiling rose surface bakelite 45 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed.

S&F stepped type electronic fan regulator flush type 240 Volts ISI marked ccomplete all as specified and directed.

S&F lamp holder, polycarbonatebody with back plate straight or angular suitable for batten fittings complete all as specified and directed.

S&F sheet metal enclosure with 20 Amp Mcb and two pin and earth plug and socket complete with one single pole MCB complete all as specified and directed.

S&F submain two single core, 4 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade drawing in and including suitable size PVC conduit (ISI marked), concealed, including 4 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed. (Note: (i) Quoted rate deemed to be included for necessary chasing/cutting and making good the surface. (ii) Three runs cable & PVC conduit pipe shall be meaured as single unit)

S&F submain two single core ,6 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade drawing in and including nd including suitable size PVC conduit (ISI marked), concealed, including 6 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed. (Note: (i) Quoted rate deemed to be included for necessary chasing/cutting and making good the surface. (ii) Three runs cable & PVC conduit pipe shall be meaured as single unit)

S&F wall security light fittings 30 watts 230v, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65/66 including necessary connection complete with all accessories including connected with 3 core copper cable of suitable 1.5 sqmm size complete all as specified and directed.

S&F LED light fitting 1x9W/1x10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED luminaire General purpose fully diffused recessed mounted 1'x4' LED luminaire with high transmitive diffuser suitable for indoor space Cat part no RC380B LED30S-6500 G5 L3W12 PSU OD.

S&F LED light fitting 1x 20 W LED light new E-Lite LED Curve with wide angle profile High lumen batten 4' with efficacy of 100 Lumens cable with suitable size and earthing complete all as specified and directed.

S&F bracket made out of galvanized tube light grade 25mm dia bore (light grade) 1.50 meter long including hot/cold bendig,beldig making hole in GI pipe and band as required,with MS clamps made of 25x3mm GI flat incl,nuts and bolts with two coat of red primer and one coat of sliver paint complete all as specified and directed.

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed. (Make :Havells, ABB, Legrand)

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 12 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed. (Make :Havells, ABB, Legrand)

S&F epoxy powder coated sheet metal enclosure for DBs, single door (when MCBs to be used), tripple pole and neutral 240 V,4 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed. (Make :Havells, ABB, Legrand)

S&F 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed. (Make :Havells, ABB, Legrand)

S&F MCB SPN 06- 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection complete all as specified and directed. (Make :Havells, ABB, Legrand) (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F MCB SPN 40 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection complete all as specified and directed. (Make :Havells, ABB, Legrand) (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F MCCB 4 pole, 3 phase, 415 volt of capacity 63 Amp, 16 KA complete with proper copper thimbles, copper reducer etc complete all as specified and directed. (Make :Havells, ABB, Legrand) (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F BLDC Without remote Ceiling fan of capacity 1200 mm, 240 volts, ISI mark, BEE rated 5 star complete all as specified and directed.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25sqmm x 4core laying properly in treanche complete all as specified and directed by Engineer-in-charge.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10sqmm x 2core laying properly in treanche complete all as specified and directed by Engineer-in-charge.

Returning, filling, including spreading, leveling, watering and well ramming in layers n.exc 25cm in soft/loose soil complete all as specified and directed.

Removal of excavated soil to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and as directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth wire electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- (i) If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department. (ii) Testing to be carried out by the contractor in presence of Engr- in- Charge , entered in the eath testing register, prepared and to be maintained by the contractor & submited to Concerned JE E/M. (iii) T&P and testing instrument(Meger) to be provided by the contractor at own cost.

M/S S M ENTERPRISE

UNITED BUILDERS

M/S Ali Trading Co

Hooghly Construction Co.

S. D. Construction Co.

FRIENDS CONSTRUCTION

Jaibalaji Enterprise