Renovation and Retrofitting of converting 18 D Block Units to 32 units at Sushma Swaraj Institute of Foreign Service SSIFS MEA Ber Sarai New Del

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT

SUSHMA SWARAJ INSTITUTE OF FOREIGN SERVICES MEA, BER SARAI, NEW DELHI

DSR AMOUNT NDSR AMOUNT TOTAL AMOUNT AMOUNT

DSR AMOUNT NDSR AMOUNT TOTAL AMOUNT AMOUNT

S.NO. DESCRIPTION

(in Rupees) (in Rupees) (in Rupees) (in Lakh)

6 FURNITURE, OUTDOOR GYM & OTHER EQUIPMENTS - 14799497.88 14799497.88 147.99

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT SUSHMA

SWARAJ INSTITUTE OF FOREIGN SERVICES MEA, BER SARAI, NEW DELHI

ABSTRACT OF COST

DSR AMOUNT NDSR AMOUNT TOTAL AMOUNT AMOUNT

DSR AMOUNT NDSR AMOUNT TOTAL AMOUNT AMOUNT

S.NO. DESCRIPTION REMARKS

(in Rupees) (in Rupees) (in Rupees) (in Lakh)

A DSR 2023 CIVIL WORKS -

3 5 REINFORCED CEMENT CONCRETE WORK 7375686.47 - 7375686.47 73.76

12 15 DISMANTLING AND DEMOLISHING 4211945.37 - 4211945.37 42.12

16 23 RAIN WATER HARVESTING & TUBEWELLS 336723.81 - 336723.81 3.37

17 26 NEW TECHNOLOGIES AND MATERIALS 709903.29 - 709903.29 7.10

5 FURNITURE, OUTDOOR GYM & OTHER EQUIPMENTS 14799497.88 14799497.88 147.99

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT SUSHMA SWARAJ INSTITUTE OF

FOREIGN SERVICES MEA, BER SARAI, NEW DELHI

BOQ-CIVIL WORKS

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

GST CORRECTION FACTOR 2025 0.973

COST INDEX OVER DSR 2023 1.03

GST x CI 1.002

Earth work in excavation by mechanical means (Hydraulic excavator)/

manual means over areas (exceeding 30 cm in depth, 1.5 m in width as

well as 10 sqm on plan) including getting out and disposal of excavated

earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.

2.6.1 All kinds of soil cum 267.32 177.89 47553.40

Filling available excavated earth (excluding rock) in trenches, plinth, sides

of foundations etc. in layers not exceeding 20cm in depth, consolidating

each deposited layer by ramming and watering, lead up to 50 and for all

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-

termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion@ one

litre per hole, 300 mm apart including drilling 12 mm diameter holes and

plugging with cement mortar 1 :2 (1 cement: 2 Coarse sand) to match the

2.35.3.1 With Chlorpyriphos/Lindane E.G. 20% with 1% concentration sqm 1206.82 310.73 374993.98

SUB-TOTAL 475057.06 -

4 CONCRETE WORK

Providing and laying in position cement concrete of specified grade

4 4.1 excluding the cost of centering and shuttering - All work up to plinth

1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8

4.1.8 graded stone aggregate 40 mm nominal size derived from natural cum 225.70 6826.92 1540845.63

Providing and fixing up to floor five level precast cement concrete solid

block, including hoisting and setting in position with cement mortar 1:3

(1 cement : 3 coarse sand), cost of required centering, shuttering

1:1½:3 (1 Cement: 1½ coarse sand (zone-Ill) derived from natural sources

4.7.1 : 3 graded stone aggregate 20 mm nominal size derived from natural cum 4.00 17928.43 71713.71

Providing and laying damp-proof course 50 mm thick with cement

concrete 1:2:4 (1 cement: 2 coarse sand (zone-Ill) derived from natural

sources : 4 graded stone aggregate 20 mm nominal size derived from

natural sources)

Providing & applying a coat of residual petroleum bitumen of grade of VG-

10 of approved quality using 1.7 kg per square metre on damp proof

course after cleaning the surface with brushes and finally with a piece of

cloth lightly soaked in kerosene oil.

SUB-TOTAL 1639140.10 -

5 REINFORCED CEMENT CONCRETE WORK

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Providing and laying in position ready mixed or site batched design mix

cement concrete for reinforced cement concrete work; using coarse

aggregate and fine aggregate derived from natural sources, Portland

Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting

of concrete, to improve durability and workability without impairing

strength; including pumping of concrete to site of laying, curing, carriage

8 5.33 for all leads; but excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge, for the

following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content

in design mix shall be payable separately. In case the cement content in

design mix is more than 110% of the specified minimum cement content,

the contractor shall have discretion to either re-design the mix or bear

the cost of extra cement.

(i) 5.33.1 All works upto plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

(ii) 5.33.2 All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Centering and shuttering including strutting , proping etc.and removal of

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete Sqm 30.00 393.01 11790.26

5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 469.77 929.28 436548.18

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 281.52 738.01 207762.48

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 191.63 963.41 184612.53

5.9.19 Weather shed, Chajjas, corbels etc., including edges sqm 58.68 953.18 55932.77

10 5.22 Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 10619.47 108.09 1147818.09

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade more. kg 18584.97 108.09 2008778.85

SUB-TOTAL 7375686.47 -

6 MASONRY WORK

Brick work with common burnt clay modular bricks of class designation

7.5 in foundation and plinth in

6.2.1 Cement mortar 1:4 (1 cement: 4 coarse sand) cum 33.29 6519.15 217041.99

Brick work with common burnt clay F.P.S. (non modular) bricks of class

12 6.4 designation 7.5 in superstructure above plinth level up to floor V level in

all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement: 6 coarse sand) cum 204.65 9125.89 1867568.20

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of

13 6.13 class designation 7.5 in superstructure above plinth level up to floor V

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 131.54 1126.26 148145.23

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at

every third course of half brick masonry

Brick work 7 cm thick with common burnt clay F.P.S. (non modular) brick

of class designation 7.5 in cement mortar 1:3 (1 cement: 3 coarse sand) in

superstructure above plinth level and upto floor five level.

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Brick edging 7cm wide 11.4 cm deep to plinth protection with common

burnt clay F.P.S. (non modular) bricks of class designation 7.5 including

grouting with cement mortar 1:4 (1 cement : 4 fine sand)

SUB-TOTAL 2397132.60 -

8 CLADDING WORK

Providing and fixing 18mm thick gang saw cut mirror polished

premoulded and prepolished) machine cut for kitchen platforms, vanity

counters, window sills , facias and similar locations of required size of

approved shade, colour and texture laid over 20mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white

cement, mixed with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edge to give high gloss finish

etc. complete at all levels.

8.2.2 Granite stone slab of colour black, Cherry/Ruby red

Providing edge moulding to 18 mm thick marble stone counters, Vanities

17 8.3 etc., including machine polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-Charge.

8.3.2 Granite work meter 86.13 512.07 44105.53

Extra for providing opening of required size & shape for wash basin/

kitchen sink in kitchen platform, vanity counter and similar location in

marble/ Granite/ stone work, including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing machine cut, mirror/ eggshell polished , Marble

stone work for wall lining (veneer work) including dado, skirting, risers of

steps etc., in required design and pattern wherever required, stones of

different finished surface texture, on 12 mm (average) thick cement

19 8.11 mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement

slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed

with pigment of matching shade, including rubbing, curing, polishing etc.

all complete as per Architectural drawings, and as directed by the

Engineer-in-Charge

18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or

Dark Emperadore etc

Providing and fixing 1st quality ceramic glazed wall tiles of any size

conforming to IS: 15622 (thickness to be specified by the manufacturer),

of approved make, in all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge, in skirting, risers of

steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement :

3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,

including pointing in white cement mixed with pigment of matching

shade complete. Size approved by engineer-in-charge

SUB-TOTAL 1075624.81 -

9 WOOD AND PVC WORK

Providing wood work in frames of doors, windows, clerestory windows

and other frames, wrought framed and fixed in position with hold fast

lugs or with dash fasteners of required dia & length (hold fast lugs or

dash fastener shall be paid for separately).

9.1.1 Second class teak wood cum 6.00 143262.76 859576.56

Providing and fixing ISi marked flush door shutters conforming to IS :

2202 (Part I) decorative type, core of block board construction with frame

of 1st class hard wood and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers on both faces of shutters.

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

35 mm thick including ISi marked Stainless Steel butt hinges with

necessary screws

Providing and fixing bright finished brass tower bolts (barrel type) with

necessary screws etc. complete :

Providing and fixing bright finished brass door latch with necessary

screws etc. complete

Providing and fixing bright finished brass 100 mm mortice latch and lock

25 9.76 with 6 levers and a pair of lever handles of approved quality with each 121.00 856.52 103639.12

necessary screws etc. complete

Providing and fixing bright finished brass handles with screws etc.

Providing and fixing aluminium extruded section body tubular type

universal hydraulic door closer (having brand logo with ISi, IS : 3564,

27 9.84 embossed on the body, door weight upto 36 kg to 80 kg and door width each 97.00 985.30 95574.40

from 701 mm to 1000 mm), with double speed adjustment with

necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISi marked,

anodised (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour and shade, with necessary screws

9.101.2 Twin rubber stopper each 115.00 72.51 8338.47

SUB-TOTAL 1957276.16 -

Structural steel work riveted, bolted or welded in built up sections,

29 10.2 trusses and framed work, including cutting, hoisting, fixing in position kg 17170.97 133.99 2300785.73

and applying a priming coat of approved steel primer all complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow

tubes, channels, plates etc., including welding, grinding, buffing,

polishing and making curvature (wherever required) and fitting the same

with necessary stainless steel nuts and bolts complete, i/c fixing the

railing with necessary accessories & stainless steel dash fasteners ,

stainless steel bolts etc., of required size, on the top of the floor or the

side of waist slab with suitable arrangement as per approval of Engineer-

in-charge, (for payment purpose only weight of stainless steel members

shall be considered excluding fixing accessories such as nuts, bolts,

fasteners etc.)

31 MR 1 8 MM CLEAR TOUGHEND GLASS sqm 48.75 2677.00 130503.75

Providing and laying Vitrified tiles in floor in different sizes (thickness to

be specified by the manufacturer) with water absorption less than 0.08%

and conforming to IS:15622, of approved brand & manufacturer, in all

colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4

coarse sand) jointing with grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only . Laying of

tiles will be done with the notch trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet for placing the tiles gently

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Providing and laying Vitrified tiles/Ceramic tiles in different sizes

(thickness to be specified by the manufacturer), with water absorption

less than 0.08% and conforming to IS: 15622, of approved brand &

33 11.47 manufacturer, in all colours and shade, in skirting, riser of steps, laid with

cement based high polymer modified quick set tile adhesive (water

based) conforming to IS: 15477, in average 6 mm thickness, including

grouting of joints (Payment for grouting of joints to be made separately).

Providing and laying machine cut, mirror polished Marble stone flooring,

in required design (Simple geometrical, abstract etc.) and in patterns in

combination with Italian marble stones of different colours, shades and

finished surface texture etc., in linear portions of the building, all

complete as per the architectural drawings, with 18 mm thick stone slab

laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4

coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm,

including pointing with white cement slurry admixed with pigment to

match the marble shade, including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge

18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or

Dark Emperadore etc

Providing and laying Honed/flamed finish Granite stone flooring in

required design and patterns, in linear as well as curvilinear portions of

the building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1

cement: 4 coarse sand) laid and jointed with cement slurry and pointing

with white cement slurry admixed with pigment of matching shade

including rubbing, curing and polishing etc. all complete as specified and

as directed by the Engineer-in-Charge :

Honed/Flamed finish granite stone slab Jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design

and patterns, in linear as well as curvilinear portions of the building all

complete as per the architectural drawings with 18 mm thick stone slab

over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4

coarse sand) laid and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade including

rubbing , curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab of colour Black, Cherry/Ruby Red or

Extra for pre finished nosing to treads of steps of marble stone/Granite

LAMINATED WOODEN FLOORING: Anti-abrasive top layer, HDF core with

water resistance, melamine decorative film for UV protection, and

37 MR 2 balancing layer for stability. Plank size: 8mm thickness x 198mm width x sqm 401.82 123.00 49423.90

1218mm length. Features AC4 wear resistance, IC2 impact resistance,

Class 5 burn resistance, and Super-Click installation system

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Providing Ethylene Propylene Diene Monomer (EPDM) Flooring 6mm

thick top layer over 30mm thick base layer mixer of recycled Rubber

buffing and SBR (Styrene-Butadiene-Rubber) in suitable proportion to

provide right base layer for comfort of user over vacuum dewatered

concrete in the play areas as per schedule of finishing. The VDC should be

laid in proper slope and with draingae system to drain off water from the

area. The base layer is mixed with 15% PU binder and pasted onto the

38 MR 3 cleaned surface. The Top Layer of EPDM flooring should be laid after the sqm 49.40 4057.00 200415.11

base layer is dry and EPDM granules, mixed with up to 25% PU binder are

pasted onto the base layer. Dust is blown off the base layer before the

top layer work begins. The colours of the EPDM granules are positioned

in such a way that they form patterns as per the sites design.

Properties of EPDM:Density should be minimum 1.60 gm/cucm.Tensile

strength should be more than 5 Mpa,Elongation should be more than

500%,Bulk density 670 g/cudm,UV resistance 4 Grey Scale rating.

12 ROOFING WORK

Making khurras 45x45 cm with average minimum thickness of 5 cm

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400

micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse

sand) and a coat of neat cement, rounding the edges and making and

finishing the outlet complete

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20

mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and

initial emittance > 0.75 on waterproof and sloped surface of terrace, laid

on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4

coarse sand) and grouting the joints with mix of white cement & marble

powder in ratio of 1:1, including rubbing and polishing of the surface

upto 3 cuts complete, including providing skirting upto 150 mm height

along the parapet walls in the same manner

SUB-TOTAL 2069831.46 -

13 FINISHING WORK

41 13.1 Cement Plaster (in Fine Sand) 12 mm cement plaster of mix :

Cement Plaster (in Fine Sand) 15 mm cement plaster on rough side of

single or half brick wall of mix:

13.2.1 1:4 (1 cement: 4 coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement

42 13.11 plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm sqm 2736.70 519.69 1422223.65

thick cement plaster 1:6 (1 cement : 6 fine sand).

43 13.16 6 mm cement plaster of mix :

Extra for providing and mixing water proofing material in cement plaster

work in proportion recommended by the manufacturers.

Finishing with Epoxy paint (two or more coats) at all locations prepared

45 13.52 and applied as per manufacturer’s specifications including appropriate

priming coat, preparation of surface, etc. complete.

(ii) 13.52.2 On concrete work sqm 48.60 235.66 11453.32

Painting with synthetic enamel paint of approved brand and manufacture

of required colour to give an even shade :

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Two or more coats on new work over an under coat of suitable shade

with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1

mm, of approved brand and manufacturer, over the plastered wall

surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50 grams/

litre of approved brand and manufacture, including applying additional

coats wherever required to achieve even shade and colour.

Applying priming coats with primer of approved brand and manufacture,

having low VOC (Volatile Organic Compound ) content

With water thinnable cement primer on wall surface having VOC content

less than 50 grams/litre

Polishing in high gloss/matt finish melamine clear polish on wood work in

required color/wooden shade texture with following process in the

sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and

then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient

drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading

with ample water to remove excess sealer layer and make the surface

further smooth after this wet rubbing, then surface is applied with special

grade melamine fillers to fill all the small and big holes/grooves etc. Filler

coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing

is done this surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using

melamine clear polish and melamine thinner in required proportion.

This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine

wet rubbed smooth, which is further allowed to dry for 12 hrs. The final

melamine polish is applied with compressor pressure spray gun using

melamine clear polish and melamine thinner mixed in required

proportion complete as per direction of Engineer-in-Charge. (Final coat to

be done in 1 or 2 layers without gap of time.)

Providing and fixing suspended false ceiling as per architectural drawings

with mouldings, cornices, cop etc.with framework made of special

sections, power pressed from M.S. sheets and galvanised with zinc

coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and

consisting of z section, angle section, C section etc. 1.6 mm thick as per

site requirement hanged from ceiling with suitable size bolts fixed to

ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia

bolts. POP Jali made of Galvanised wire 24 gauge to provide additional

support, prevent cracking, setting & reinforcement to Gypsum plaster

shall be fixed to the sections with G. I. wire in the shape and design in the

entire area as per architectural drawing. The ceiling is to be plastered

with minimum 12mm thick Plaster of Paris in true line, level and shapes.

Nothing extra is payable for providing moulding, cornices or cope and flat

area is to be measured for payment. The sections, wire mesh, all the

materials and drawing with fixing details shall be got approved from the

Engineer-in-Charge before procurement and execution of work.

14 REPAIRS TO BUILDING

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5

sq.meters and under, including cutting the patch in proper shape, raking

52 14.1 out joints and preparing and plastering the surface of the walls complete,

including disposal of rubbish to the dumping ground, all complete as per

direction of Engineer-in-Charge

14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand) sqm 602.54 548.60 330551.46

SUB-TOTAL 330551.46 -

15 DISMANTLING AND DEMOLISHING

Dismantling doors, windows and clerestory windows (steel or wood)

53 15.12 shutter including chowkhats, architrave, holdfasts etc. complete and

stacking within 50 metres lead :

15.12.1 Of area 3 sq. metres and below each 256.00 368.00 94209.07

Dismantling tile work in floors and roofs laid in cement mortar including

stacking material within 50 metres lead.

15.23.1 For thickness of tiles 10 mm to 25 mm sqm 1137.45 73.56 83671.52

Dismantling stone slab flooring laid in cement mortar including stacking

55 15.25 of serviceable material and disposal of unserviceable material within 50 sqm 118.04 267.03 31519.30

Demolishing cement concrete manually/ by mechanical means including

56 15.2 disposal of material within 50 metres lead as per direction of Engineer -

(i) 15.2.1 Nominal concrete 1:3:6 or richer mix (including equivalent design mix) cum 430.60 2439.58 1050484.07

(ii) 15.2.2 Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) cum 458.10 1506.89 690307.93

Demolishing R.C.C. work manually/ by mechanical means including

57 15.3 stacking of steel bars and disposal of unserviceable material within 50 cum 10.20 3559.03 36302.08

metres lead as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in

58 15.5 R.C.C. or R.B. work (Payment shall be made on the cross sectional area of sqm 40.80 1149.71 46908.26

R.C.C. or R.B. work) as per direction of Engineer-in-charge.

Demolishing mud phaska in terracing and disposal of material within 50

Demolishing brick work manually/ by mechanical means including

60 15.7 stacking of serviceable material and disposal of unserviceable material

within 50 metres lead as per direction of Engineer-in-charge.

Dismantling old plaster or skirting raking out joints and cleaning the

61 15.56 surface for plaster including disposal of rubbish to the dumping ground sqm 5642.99 54.77 309064.89

within 50 metres lead.

Dismantling steel work in single sections including dismembering and

stacking within 50 metres lead in:

15.17.2 Channels, angles, tees and flats (20kg/sqm)

Dismantling C.I. or asbestos rain water pipe with fittings and clamps

including stacking the material within 50 metres lead :

Dismantling G.I. pipes (external work) including excavation and refilling

trenches after taking out the pipes, manually/ by mechanical means

including stacking of pipes within 50 metres lead as per direction of

Engineer-in-charge :

15.44.1 15 mm to 40 mm nominal bore metre 1800.00 150.13 270230.51

Disposal of building rubbish / malba / similar unserviceable, dismantled

or waste materials by mechanical means, including loading, transporting,

65 15.60 unloading to approved municipal dumping ground or as approved by cum 3582.42 264.53 947650.69

Engineer-in-charge, beyond 50 m initial lead, for all leads including all

lifts involved.

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

SUB-TOTAL 4211945.37 -

Providing and laying design mix cement concrete of M-30 grade, in

roads/ taxi tracks/ runways, using cement content as per design mix,

using coarse sand and graded stone aggregate of 40 mm nominal size in

appropriate proportions as per approved & specified design criteria,

providing dowel bars with sleeve/ tie bars wherever required, laying at

site, spreading and compacting mechanically by using needle and surface

66 16.43 vibrators, levelling to required slope/ camber, finishing with required

texture, including steel form work with sturdy M.S. channel sections,

curing, making provision for contraction/ expansion, construction &

longitudinal joints (10 mm wide x 50 mm deep) by groove cutting

machine, providing and filling joints with approved joint filler and

sealants, complete all as per direction of Engineer-in-charge (Item of joint

fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).

Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less

cement used as per design mix is payable/ recoverable separately

Cement concrete manufactured in automatic batching plant (RMC plant)

including transportation to site in transit mixer

Providing and fixing pre-moulded joint filler in expansion joints of RCC

roads / CC pavements after making the joints dust free with high pressure per cm

air jet cleaners, all complete as per direction of the Engineer-in-Charge. depth per

67 16.45 (Pre-moulded joint fillers shall be made of bitumen hot sealing compound cm width 137.50 5.31 730.35

impregnated fibre board having impregnation more than 35%, conforming per metre

to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound

Providing and laying at or near ground level factory made kerb stone of M-

25 grade cement concrete in position to the required line, level and

curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand),

including making joints with or without grooves (thickness of joints

68 16.69 except at sharp curve shall not to more than 5 mm), including making cum 2.92 10139.76 29567.53

drainage opening wherever required complete etc. as per direction of

Engineer in-charge (length of finished kerb edging shall be measured to

calculate volume for payment). (Precast C.C. kerb stone shall be approved

by Engineer-in-charge).

SUB-TOTAL 1314976.15 -

21 ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and

partitions with extruded built up standard tubular sections/ appropriate Z

sections and other sections of approved make conforming to IS: 733 and

IS: 1285, fixing with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom and sides

69 21.1 with required EPDM rubber/ neoprene gasket etc. Aluminium sections

shall be smooth, rust free, straight, mitred and jointed mechanically

wherever required including cleat angle, Aluminium snap beading for

glazing / panelling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge. (Glazing,

paneling and dash fasteners to be paid for separately) :

21.1.1 For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50

For shutters of doors, windows & ventilators including providing and

fixing hinges/ pivots and making provision for fixing of fittings wherever

required including the cost of EPDM rubber / neoprene gasket required

(Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket etc.

complete as per the architectural drawings and the directions of engineer-

in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.5

Providing and fixing fly proof stainless steel grade 304 wire gauge, to

windows and clerestory windows using wire gauge with average width of

aperture 1.4 mm in both directions with wire of dia. 0.50 mm all

9.135.1 With 2nd class teak wood beading 62X19 mm sqm 67.20 1600.65 107563.53

Providing and fixing window locks of reputed company as per approval of

the NBCC/Client (Set of 2)

22 WATER PROOFING

Providing and laying water proofing treatment in sunken portion of WCs,

bathroom etc., by applying cement slurry mixed with water proofing

cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed

to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water

proofing cement compound @ 0.126 kg/sqm. This layer will be allowed

to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed

Providing and laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement

admixed with water proofing compound conforming to IS. 2645 and

approved by Engineer-in-charge over the RCC slab including adjoining

walls upto 300 mm height including cleaning the surface before

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to

115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand)

admixed with water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge over 20 mm thick layer of cement mortar

of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-charge

to required slope and treating similarly the adjoining walls upto 300 mm

height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement

slurry using 2.75 kg/ sqm of cement admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix

1:4 (1 cement :4 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge including

laying glass fibre cloth of approved quality in top layer of plaster and

finally finishing the surface with trowel with neat cement slurry and

making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a

minimum period of two weeks for curing and for final test. “All above

operations to be done in order and as directed and specified by the

Engineer-in-Charge”:

With average thickness of 120 mm and minimum thickness at khurra as

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Providing and applying fibre reinforced elastomeric liquid water proofing

membrane with resilient acrylic polymers having Sun Reflectivity Index

(SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm.

One coat of self-priming of elastomeric waterproofing liquid (dilution

with water in the ratio of 3:1) and two coats of undiluted elastomeric

waterproofing liquid (dry film thickness of complete application/system

not less than 500 microns). The operation shall be carried out after

scrapping and properly cleaning the surface to remove loose particles

with wire brushes, complete in all respect as per the direction of Engineer

Providing & Applying polymer modified, flexible cementatious negative

side waterproofing coating with elastic waterproofing polymers on

interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat

of self priming of cementatious waterproofing polymer(dilution with

77 22.23A water in the ratio of 1:1) and two coats of cementatious waterproofing sqm 1502.46 448.33 673597.44

polymer (dilution with water in the ratio of 3:1 ) after scrapping and

properly cleaning the surface to remove pre-existing paint film & loose

particles till plaster is visible, complete in all respect as per the direction

of Engineer-in-Charge.

SUB-TOTAL 3614138.09 -

23 RAIN WATER HARVESTING & TUBEWELLS

Providing and fixing factory made precast RCC perforated drain covers,

having concrete of strength not less than M-25, of size 1000 x 450x50

77 23.9 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross each 240.00 1403.02 336723.81

sectional T.M.T. hoop bars, including providing 50 mm dia perforations @

100 to 125 mm c/c, including providing edge binding with M.S. flats of

size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

SUB-TOTAL 336723.81 -

26 NEW TECHNOLOGIES AND MATERIALS

Providing and injecting approved grout in proportion recommended by

the manufacturer into cracks/honey-comb area of concrete/masonry by

77 26.35 suitable gun/pump at required pressure including cutting of nipples after

curing etc. complete as per directions of Engineer-in-Charge.

(The payment shall be made on the basis of actual weight of approved

grout injected.)

26.35.3 Epoxy injection grout in concrete/RCC work of approved make KG 1280.00 554.61 709903.29

SUB-TOTAL 709903.29 -

OTHER NDSR ITEMS

Supplying and applying on surface, STONE FINISH texture to external wall

surfaces comprising of silicone and ceramic based texture finish which is

highly elastic and is abrasion & UV resistant with 2 or more coat system;

highly water repellant, antialgae & anti-fungal, heat reflective, fire

resistant and low on VOC in nature. The coating covers minor hairline

cracks with application method which includes 1 coat of Polyunder

(sealer coat) with roller/ brush/ spray, 1 or more coats of Granitowall in

approved shade with stainless steel trowels. The finish is colorfast, water

repellant, resistant to condensate formation, ensures good breathability

for the substrate

Rebars will be installed using chemical grout following the

manufacturer’s printed installation instructions (MPII). Drilling, hole

cleaning, mortar injection, and rebar installation will be done as per the

77 MR specified procedures to ensure proper embedment and alignment, with

the use of automated systems for accurate chemical dosing. The work

shall be carried out as per the technical specification and approved by the

Engineer-in-Charge.

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Providing and fixing Roller Blinds as per the approved sample comprising

of optima screen Fabric comprising of 22% polyester, 78% PVC with

openess factor of 1-5%.Fabric weight 410-465 G weight per sqm,

Thickness 0.67 mm.

The Roller blind system consists of 38mm OD extruded out of Aluminium

alloy 6063 T6 with silver anodized to provide an everlasting finish and

luster, the rotary unit shall be 36mm in OD incorporating a clutch

mechanism composed of low – flexing braided polyster cord with nylon

core, Control Ball chain shall be composed of braided nylon cord (2mm

78 MR 11 dia) with high engineering grade plastic beads of 4.5mm diameter sqm 352.50 1401.00 493853.44

mounted co-axially on the cord with a pitch of 6.2mm (C-T-C) Bottom rail

should be powder coated Aluminium flat bottom rail of 290 gm to finish

it from the ends it should have rail end caps. The clutch will be at the

tube. The return end cap bracket shall incorporate snap spring design to

facilitate easy installation and removal for maintenance activities. The

bracket shall be finished with a flush mounting cover on each side

providing an aesthetic finish. It should handle up to 5 Kgs of material. The

clutch should mount flush to the face of the bracket which minimize the

light gap between the shade and the window frame.

Artwork Development Custom-designed, high-resolution (min. 300 DPI)

78 digital artwork tailored to room theme. Printed on canvas or synthetic

media with synthetic frame

1 BHK Artwork above Headboard : 300mm (Width) x 700mm (Height) Set

1 BHK Artwork above Sofa Living room: 1000mm (Width) x 600mm

2 BHK Artwork above Headboard: 300mm (Width) x 700mm (Height) Set

2 BHK Artwork above Sofa Living room: 1000mm (Width) x 600mm

Supply and installation of 4 mm thick Polycarbonate Sheet on the steel

79 MR 14 structure with necessary self driven screws, washers etc. as per direction 20.00 3426.00 68520.00

of NBCC/Client.

Providing and fixing rectangular Mirror 450x600mm (minimum) with LED

for bathrooms with backlight, touch sensor and 3 light effects with

necessary screws, fastner, caps etc. as per direction of Engineer-in-

SUB-TOTAL - 3990783.78

81 FIRE EVACUATION PHOTOLUMINICENT SIGNAGES

Providing and fixing round corner signages with radius 8mm to 12mm,

made of rigid PVC sheet with premium photoluminicent of illumination

upto minimum 4 hours. With UV printing for Graphic and text. adhering

to latest NBC standards, Mounted using SS screws or 3M VHB tape asper

direction of Engineer in charge - stair floor level Indicator (Size = 382W x

Providing and fixing round corner signages with radius 8mm to 12mm,

made of rigid PVC sheet with premium photoluminicent of illumination

(ii) MR 17 upto minimum 4 hours. With UV printing for Graphic and text. adhering 9.00 684.00 6156.00

to latest NBC standards, Mounted using SS screws or 3M VHB tape asper

direction of Engineer in charge - fire hose cabinet (Size = 150W x 200H)

82 AREA IDENTIFICATION SIGNAGES

Digitally signed by MAYANK

S.NO. DESCRIPTION OF ITEMS UNIT QTY NET RATE DSR AMOUNT REMARKS

Supply & installation Signage Made Of Base 3 MM Beton silveri Beton

whitel Swiss snow finish ACP panel Box having 6063 Alloy profiles to

house the edge of ACP with in groove. Profile size 18 X 38 mm @edges

and to be eprotuded by 5mm x 3mm beyond side surface from front side

to make teh surface appeared recessed. Powder coated I Anodised as per

approved shade, Fascia 3 mm acrylic sheet to be Stuck on base ACP Sheet

in staggered manner before fixing of signage then Content CNC Cut

Acrylic 2 mm thick fixed on signage facia. signage to be mounted using

clamps at backside of profile. teh sheets and content to be duly CNC cut

with neat and clean polised edges

SUB-TOTAL - 77260.00

DSR & NDSR AMOUNT 55596462.44 7034917.39

GROSS AMOUNT IN RUPEES 62631379.83

AMOUNT IN LAKHS 626.31

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT SUSHMA SWARAJ

INSTITUTE OF FOREIGN SERVICES MEA, BER SARAI, NEW DELHI

BILL OF QUANTITY-ELECTRICAL

DSR-22 &DSR DSR NDSR

S.No. Description of Item Unit Quantity NET RATE

25 EM Code Amount(Rs) Amount(Rs)

COST INDEX, CORRECTION FACTOR AND GST ALTERATION 1.065

Sub-Head : WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

1 1.10 conduit, with modular switch, modular plate, suitable Gl box and

earthing the point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way modular switch,

modular plate, suitable Gl box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable

etc. as required.

Wiring for circuit/ submain wiring along with earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 648.00 355.82 230571.06

1.14.5 2 X 10 sq. mm + 1 X 6 sq. mm earth wire Metre 30.00 607.24 18217.11

Supplying and drawing following pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmoured telephone

cable in the existing surface/ recessed steel/ PVC conduit as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm

solid copper conductor PE insulated, shielded with fine tinned

copper braid and protected with PVC sheath in the existing

surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing following modular switch/ socket on the

7 1.24 existing modular plate & switch box including connections but

excluding modular plate etc. as required.

1.24.6 Telephone socket outlet No. 32.00 157.67 5045.39

1.24.7 TV antenna socket outlet No. 64.00 157.67 10090.79

Supplying and fixing two module stepped type electronic fan

regulator on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

Digitally signed by MAYANK

Supplying and fixing modular blanking plate on the existing

9 1.26 modular plate & switch box excluding modular plate as required. No. 260.00 42.61 11079.41

Supplying and fixing following size/ modules, Gl box along with

10 1.27 modular base & cover plate for modular switches in recess etc.

1.35 Installation, Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing up to two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, V,

complete as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (up to 30 cm) with 1.5

13 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, No. 69.00 294.03 20288.11

including providing and fixing phenolic laminated sheet cover on

the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

14 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Extra for fixing the louvers/ shutters complete with frame for a

exhaust fan of all sizes.

Supplying & fixing suitable size Gl box with modular plate and

cover in fronton surface or in recess including providing and

16 1.57 fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" No. 68.00 774.49 52665.55

curve including connections, painting etc. as required.

Sub-Head : MCCB, MCB & OB'S

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

complete with tinned copper bus bar, neutral bus bar, earth bar,

din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/RCCB/lsolator)

Supplying and fixing of following ways surface/ recess mounting,

vertical type, 415 V, TPN MCB distribution board of sheet steel,

dust protected, duly powder painted, inclusive of 200 A tinned

18 2.5 copper bus bar, common neutral link, earth bar, din bar for

mounting MCBs (but without MCBs and incomer) as required .

(Note : Vertical type MCB TPDB is normally used where 3 phase

outlets are required.)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, the existing

21 2.12 MCB DB complete with connections, testing and commissioning

etc. as required.

Digitally signed by MAYANK

Supplying and fixing following rating, four pole, 415 V, isolator in

22 2.13 the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase

and neutral), 240 V, residual current circuit breaker (RCCB),

23 2.14 having a sensitivity current 30 mA in the existing MCB DB

complete with connections, testing and commissioning etc. as

Supplying and fixing following rating, four pole, (three phase

and neutral), 415 volts, residual current circuit breaker (RCCB),

24 2.15 having a sensitivity current 30 mA in the existing MCB DB

complete with connections, testing and commissioning etc. as

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Sub-Head : EARTHING

Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

26 5.4 cover plate having locking arrangement and watering pipe of 2.7 Set 2.00 7960.13 15920.26

metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.l. wire at 0.50 metre below

27 5.7 ground level for conductor earth electrode, including Metre 30.00 54.33 1629.95

connection/ termination with Gl thimble etc. as required.

Supplying and laying 25 mm X 5 mm G.l. strip at 0.50 metre

below ground as strip earth electrode, including connection/

28 5.9 terminating with G.l. nut, bolt, spring, washer etc. as required. Metre 30.00 153.41 4602.22

(Jointing shall be done by overlapping and with 2 sets of G.l. nut

bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.l. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.l. wire on surface or in recess

for loop earthing as required.

Sub-Head : MV CABLE LAYING

Laying of one number PVC insulated and PVC sheathed / XLPE

power cable of 1.1 KV grade of following size direct in ground

including excavation, sand cushioning, protective covering and

refilling the trench etc as required.

7.1.2 Above 35 sq. mm and up to 95 sq. mm Metre 111.30 431.46 48021.26

7.1.3 Above 95 sq. mm and up to 185 sq. mm Metre 210.00 449.57 94409.36

Laying of one number PVC insulated and PVC sheathed / XLPE

32 7.5 power cable of 1.1 KV grade of following size in the existing

RCC/ HUME/ METAL pipe as required.

7.5.2 Above 35 sq. mm and up to 95 sq. mm Metre 49.90 60.72 3030.11

7.5.3 Above 95 sq. mm and up to 185 sq. mm Metre 30.00 82.03 2460.91

Laying and fixing of one number PVC insulated and PVC

33 7.7 sheathed / XLPE power cable of 1.1 KV grade of following size on

wall surface as required.

7.7.1 Up to 35 sq. mm (clamped with 1mm thick saddle) Metre 272.00 58.59 15937.31

Above 35 sq. mm and up to 95 sq. mm (clamped with 25x3mm

Above 95 sq. mm and up to 185 sq. mm (clamped with

25/40x3mm MS flat clamp)

Sub-Head : MV CABLE JOINTING & END TERMINATION

Digitally signed by MAYANK

Supplying and making end termination with brass compression

gland and aluminium lugs for following size of PVC insulated and

PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade

Sub-Head : MISC. CIVIL ITEMS

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box

for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of

1.5 mm thick M.S. sheet with its top surface hacked for proper

CIVIL DSR- 2023

35 bonding, top lid shall be screwed into the cast iron/ M.S. sheet box Each 69.00 235.06 16219.46

by means of 3.3 mm dia round headed screws, one lock at the

corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as

per standard drawing.(DSR Civil 2023 Item no. 10.18.)

Digitally signed by MAYANK

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120

lm/Watt) Supplying, installation, Testing & Commissioning of LED

Recessed/ surface Down lighter (Round/square/ Rectangular) SMD

type of following body material with PMMA and prismatic diffuser

and construction as per IS: 10322 with driver as per the requirement

with Driver efficiency >85%, Operating voltage AC 140-270 Volt,

frequency 50/60 hz, Operating temp range-15 deg to 40 deg

centigrade, internal surge protection of 2.5 KV with Short & Open

circuit protection, THD < 10%, P. F.20.95, IP20, CRI >80, UGR (Unified

Glare Rating) < 19, Flicker free (flicker should be below 5%), life time

(LED, Driver & electrical circuitary), of minimum 50000 Burning Hours

with 70% of initial Lumen maintained till life ends, CCT 3000°K /

4000°K / 5700°K/6000°K / 6500°K (As per ANSI Bin), SDCM (Standard

36 1.1 Deviation Color Matching) <3, Maximum power consumption should

not more than the specified rating and Fixture shall be confirming to

relevant BIS standards and trade mark certificate (T.C.).

Manufactures Word Mark/Name Engraved/ Embossing/ Screen

printing on housing Complete in all respect i/c connections with 1.5

sq mm FRLS, PVC insulated copper conductor single core cable and

earthing etc. as required with Minimum 5 year OEM warranty.

System lumen efficacy ≥105 and <120 lm/Watt output. LM79 & LM80

Test report from NABL lab for all testing required for LED fixtures as

per BIS shall be submitted. Shape size and CCT shall be as approved

by Engineer-in-Charge as per requirement. (Thermal management:

heat sink of aluminium housing such that LED junction temperature

shall not rise above 90°C)

LED Batten light (System lumen efficacy ≥105 <120 lm/Watt)

Supplying, installation, Testing & Commissioning of LED surface

mounted Batten light of following body material and construction as

per IS : 10322 with driver (Replaceable) as per the requirement with

Driver efficiency >85% ,Operating voltage AC 140-270 Volt, freq 50/60

hz, Operating temp range -15 deg to 40 deg centigrade, internal

surge protection of 2.5 KV with Short & Open circuit protection

,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be

below 5 %), life time (LED,Driver & electrical circuitary), of minimum

50000 Burning Hours with , 70% of initial Lumen maintained till life

ends, CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI

Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power

consumption should not more than the specified rating and Fixture

37 1.9 shall be of relevant BIS standard and trade mark certificate ( T.C.).

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen

printing on housing. complete in all respect i/c connections with 1.5

sq mm FRLS, PVC insulated copper conductor single core cable and

earthing etc. as required with Minimum 5 year OEM warranty.

System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80

Test report from NABL lab for all testing required for LED fixtures as

per BIS shall be submitted. Shape size and CCT shall be as approved

by Engineer-in-Charge as per requirement. (Thermal management:

heat sink of aluminium housing such that LED junction temperature

shall not rise above 90°C).Powder coated die cast /Extruded

aluminium Body (Thickness > 1.20 mm

Digitally signed by MAYANK

LED Flood Light, powder coated pressure die cast aluminium (System

lumen efficacy 105 <120 lm/Watt)

Supplying, installation, Testing & Commissioning of Flood Light,

powder coated pressure die cast aluminium body with built in or

separate driver as per the requirement with Driver efficiency >85%,

Input voltage: Input voltage: 140-270 Volt AC, freq 50/60 hz,

Operating temp range -15 deg to 50 deg centigrade, internal surge

protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,

THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >80,

under voltage and over voltage protection, EMI-EMC as per CISPR-15,

lenses for beam angle 30 deg-120deg as per the application and the

project requirementdegsuitable tilt able fitting, life time (LED, Driver

& electrical circuitary) of minimum 50000 Burning Hours with 70% of

initial Lumen maintained till life ends as per LM80 extrapolation IES

per ANSI Bin), SDCM(Standard Deviation Color Matching) <5,

Maximum power consumption should not more than the specified

rating and Fixture shall be of relevant BIS standard complete in all

respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper

conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy 105 <120

lm/Watt output. LM79 & LM80 Test report from NABL lab for all

testing required for LED fixtures as per BIS shall be submitted. Shape

size and CCT shall be as approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of aluminium housing

such that LED junction temperature shall not rise above 90°C).

Brush Less DIrect Current (BLDC) Motor

Supply, Installation, Testing and Commissioning of ceiling fan with

Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos.

metal( Aluminum alloy) blades, 30 cm long down rod, 2 nos.

canopies, shackle kit, safety rope, copper winding, steel/Al

bodyPower Factor not less than 0.9, Service Value (CM/M/W)

38 2.10 minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD

(Total Harmonic Distortion) less than 10%, remote (prefreably mobile

app based) for speed control and all remaining accessories including

safety pin, nut bolts, washers, temperature rise=75 degree C (max.),

insulation resistance more than 2 mega ohm, suitable for 230 V, 50

Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply,

earthing etc. complete as req

1200mm, BEE 5 star rating, service value≥ 6.0

CM/Min/Watt, air delivery 210 CM/Min(Minimum)

Digitally signed by MAYANK

Supply , Installation, Testing and Comissioning of Air

Cooled Hi Wall split type Air conditioners complete with

Indoor unit(IDU), Out door unit (ODU), surface /

concealed copper Refrigerant piping with insulation

(closed cell elastomeric nitrile rubber tubular pipe

section) upto 3 Mtr (IDU to ODU), copper power cable

upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-

407 Green Refrigerant, wireless Remote control, suitable

for working between 180-260V with low & high voltage

cutoff and 50 hz ,1 phase AC supply capable of

performing cooling,dehumidification, air circulation of

following capacity with Scroll / rotary compressor. The

system shall be able to deliver 100% of the rated

capacity upto 42 Degree Celcius. Min 5 year Original

Equipment Manufacturer (OEM) warranty both

compressor and Printed Circuit Board (PCB). Must

comply : Electrical cable IS 694 or IS 9968 temperature

sensing control IS /International Electrotechnical

Commission (IEC) 60730, hermetic compressor IS

10617, heat exchanger IS 11329, capacitor IS 2993 and

motor IS 12615. Complete as per CPWD specification

and IS : 1391 Part II 2023. The system shall be able to

operate up to 50°C (out door ambient temperature).

Inverter Type - Cooling only

8.2.4 2.0 TR with 5 Star BEE Rating Nos 35.00 55440.00 1940400.00

Digitally signed by MAYANK

Supplying and fixing of AC 200mm Sweep, 230/250 Volts, 50 Hz

39 A.R. - 1 exhaust fan (Light Duty) with blades,cover etc. complete as each 69 1318.30 90962.87

Mirror Light 10W Thea Batten_NN-2024-25-247,6500K,IP20

Supply, Installation, Testing and Commissioning of surface mounted

LED Batten for Mirror Light with PC housing with PC Diffuser with

engg-plastic end caps and Clamps for Surface Mounting arrangement

with groove inside for PCB. LED populated on PCB comprising of

LED’s connected. The luminaire shall be suitable for offices, factories,

warehouses areas. The system wattage shall be 10W, providing

system luminous flux 1000 lumens respectively with a luminaire

efficacy of > 100 lm/W. The fixture shall have a beam angle of 120°,

40 A.R. - 2 Correlated colour temperature of 6500K/5700K and CRI ≥80. Lumen each 33 753.81 24875.85

maintenance should achieve L70B50 at 25,000 hours. Electrical

parameters should include 240V AC input, Power Factor > 0.90, and

THD < 20%. Driver shall be Constant Current, Non-Isolated, Integral,

Class II Insulation Level, Operating Temperature: 0° C TO 45° C,

Protection ratings shall include IP20 and IK02 with Internal surge

protection up to 3kV shall be provided. should be of same make &

must have separate BIS approval. Luminaire manufacture shall

provide LM79 report from in house NABL accredited lab & LM80

report issued by LED manufacturer.

41 A.R. - 3 Supplying and fixing of 260 led profile strip (5M) Set 32 3974.65 127188.90

Supplying and fixing of 5m Linea Bright LED Cove Lighting with driver

Supply and fixing of single phase multifunctional electronic

43 A.R. - 5 energy meter 10 to 60 Amp. capacity fitted in integral box each 32 3147.67 100725.28

on wall complete in all respect .

Supplying and laying of aluminium conductor XLPE insulated

armoured served sheathed cables 1100 Volts grade.

Supply & Erection of factory fabricated & wired metal clad

dust and vermin proof floor mounting, M.S. Channel Base

with bottom and top cable entreis Electrical control panel

with TPN MCCB's (Four Pole 36 KA with thermal

magnatic release)Switches Complete and instrument chamber

etc.complete in all respects. The instrument chamber shall be

separate and shall comprise of flush type digital metering

system for phase to phase voltage and single phase

voltage, current and other parameters(KVA,P.F,KW etc) in

each phase with touch type selector switches for different

readings, instrument fuses, current transformer etc. The panel

board shall have suitable capacity electrolytic

AR-7 alumininum busbars as per IS8623 or above istulated

with heat shrink sleeving and mounted on non hygroscopic

supports such as CMC/BMC support with deteachable side

covers and shall be suitable for extension on the sides. The

MCCB's shall be complete with suitable cable end boxes,

compression glands and indicating lamp on incoming

etc.The Job includes the grounting of the board as per

directions of Engineer-in charge. All out goings of 100 Amp

and above shall have an Ammeter. The panel board shall be

fabricated with CRCA sheet with a minimum thickness of

1.6mm/2mm. Cubicle type switch board shall be of cat B Only.

45 AR-7.1 Incoming

400 Amp. MCCB-1 Nos.

Digitally signed by MAYANK

100 Amp.MCCB-2Nos. & 63 Amp.MCB-33 Nos. each 1 369573.93 369573.93

63 Amp.MCB-4 Nos. (spare)

40 Amp.MCB-2 Nos. (spare)

DSR AMOUNT + NDSR AMOUNT 7235697.01 1533824.36

TOTAL AMOUNT (DSR+NDSR) in Rupees 8769521.37

TOTAL AMOUNT (DSR+NDSR) in Rupees 8769521.37

TOTAL AMOUNT (DSR+NDSR) in Cr. 87.70

TOTAL AMOUNT (DSR+NDSR) in Cr. 87.70

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT

SUSHMA SWARAJ INSTITUTE OF FOREIGN SERVICES MEA, BER SARAI, NEW DELHI

S.No. DESCRIPTION OF WORKS DSR 2023 AMOUNT NDSR AMOUNT

1 SANITARY INSTALLATIONS & C.P FITTINGS 339700.97 2673023.20

2 INTERNAL SOIL, WASTE & RAIN WATER DRAINAGE SYSTEM 260328.87 279026.52

3 INTERNAL WATER SUPPLY SYSTEM 1416232.28 0.00

4 EXTERNAL SEWERAGE & RAIN WATER DRAINAGE SYSTEM 1257398.54 0.00

DSR AMOUNT & NDSR AMOUNT 3273660.66 2952049.72

TOTAL (DSR AMOUNT + NDSR AMOUNT) 6225710.38

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT SUSHMA SWARAJ INSTITUTE OF FOREIGN SERVICES MEA, BER

SARAI, NEW DELHI

SCHEDULE OF QUANTITIES FOR PLUMBING WORKS

SL. NO Ref: DSR 2023 DESCRIPTION QTTY UNIT NET RATE AMOUNT

GST CORRECTION FACTOR 0.973

COST INDEX OVER DSR 2023 1.03

GST x CI 1.002

I SANITARY INSTALLATIONS & C.P FITTINGS

Providing and fixing of wall mounted water closet with seat and soft closing lid,

concealed cistern including flush pipe, with manually controlled device (push

button), with all fittings and fixtures complete, including cutting and making good

the walls and floors wherever required.

2 MR-2 Providing & fixing health faucet with flexible pipe of 1 metre length 33 each 1689.30 55746.90

3 17.34 Providing and fixing toilet paper holder :

4 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931

18.49.1 a) 15 mm nominal bore 33 each 507.91 16761.03

Providing & fixing counter top wash basin with 32mm C.P. brass waste of standard

pattern including cutting & making good the walls wherever required.

Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved

6 17.31 quality) complete with 6mm thick hard board ground fixed to wooden cleats with 33 each 1611.47 53178.56

C.P. brass screws and washers complete.

7 MR-4 Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make. 33 each 2092.40 69049.20

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112

8 17.71 mm distance from wall of standard shape with bracket of the same materials with 33 each 168.72 5567.72

snap fittings of approved quality and colour, weighing not less than 105 gms.

9 MR-5 Providing & fixing S.S. Towel ring round with round flange 33 each 1190.00 39270.00

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with

10 17.10 C.I. brackets and stainless steel plug 40 mm, including painting of fittings and

brackets, cutting and making good the walls wherever required :

17.10.2 Kitchen sink without drain board

11 MR-6 Providing & fixing single lever pillar cock with swinging spout for sink. 32 each 1986.80 63577.60

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of

approved quality conforming to IS:8931

13 18.21 Providing and fixing unplasticised PVC connection pipe with brass unions.

18.21.2 45 cm length

18.21.2.1 15 mm nominal bore 99 each 97.96 9698.44

14 MR-8 Providing and fixing wall spout with 2-way diverter of quality & make. 33 each 6971.80 230069.40

Providing and fixing C.P. brass long body bib cock of approved quality conforming to

IS standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore 42 each 800.70 33629.39

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on

16 17.33 anodised aluminium angle frame with C.P. brass brackets and guard rail complete 33 each 1085.87 35833.80

fixed with 40 mm long screws, rawl plugs etc., complete.

17 MR-9 Providing & fixing S.S. Towel rail in bathing area. 33 each 1993.90 65798.70

Digitally signed by MAYANK

SL. NO Ref: DSR 2023 DESCRIPTION QTTY UNIT NET RATE AMOUNT

18 MR-10 Providing and fixing C.P. brass shower rose of approved quality. 33 each 12284.40 405385.20

19 MR-11 Providing & fixing S.S. Grating with cockroack trap. 122 each 848.40 103504.80

Digitally signed by MAYANK

SL. NO Ref: DSR 2023 DESCRIPTION QTTY UNIT NET RATE AMOUNT

II INTERNAL SOIL, WASTE & RAIN WATER DRAINAGE SYSTEM

Providing and fixing UPVC pipes complete with fittings including cutting and making

good the walls etc.

MR-12 UPVC SWR Single socket pipe type-B 40 mm dia 130 Metre 424.40 55172.00

MR-13 UPVC SWR Single socket pipe type-B 50 mm dia 80 Metre 466.40 37218.72

MR-14 UPVC SWR Single socket pipe type-B 110 mm dia 275 Metre 656.00 180400.00

Providing and fixing trap of self cleansing design with screwed down or hinged

21 17.60.1.3 grating with or without vent arm complete, including cost of cutting and making

good the walls and floors :

22 MR-15 Providing and fixing nahani trap 110 mm. 38 No. 164.10 6235.80

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast

iron/cast iron (spun) pipe embedded in and including cement concrete blocks

10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size), including cost of cutting holes and making good the walls etc. :

Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast

(spun) iron pipes of diameter :

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming

25 12.41 to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving

10mm gap for thermal expansion.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm

diameter and weighing not less than 440 grams.

Providing and fixing on wall face unplasticised PVC moulded fittings/accessories for

unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including

jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal

12.42.1 Coupler

12.42.4 Single tee without door

12.42.5 Bend 87.5 degree

12.42.6 Shoe (Plain)

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-

PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS

28 12.43 screws of required length including cutting brick work and fixing in cement mortar

1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size)

over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1

cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and

making and finishing the outlet complete.

III INTERNAL WATER SUPPLY SYSTEM

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded fittings

i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and the cost of cutting chases and

making good the same including testiang of joints complete as per direction of

Engineer in Charge.

Digitally signed by MAYANK

SL. NO Ref: DSR 2023 DESCRIPTION QTTY UNIT NET RATE AMOUNT

Concealed work including cutting chases and making good the walls etc.

18.8.1 15 mm nominal dia pipes 100 Metre 498.89 49889.02

18.8.2 20 mm nominal dia pipes 370 Metre 538.78 199347.62

18.8.3 25 mm nominal dia pipes 260 Metre 628.62 163442.16

Digitally signed by MAYANK

SL. NO Ref: DSR 2023 DESCRIPTION QTTY UNIT NET RATE AMOUNT

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

31 18.7 fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing

of pipes & fittings with one step CPVC solvent cement and testing of joints complete

as per direction of Engineer in Charge.

Internal work-Exposed on wall

18.7.2 20 mm nominal dia pipes 38 Metre 335.73 12690.73

18.7.3 25 mm nominal dia pipes 63 Metre 402.43 25353.05

18.7.4 32 mm nominal dia pipes 139 Metre 519.89 72056.21

18.7.5 40 mm nominal dia pipes 188 Metre 704.49 132725.81

18.7.6 50 mm nominal dia pipes 220 Metre 936.20 206150.31

18.9.7 65 mm nominal dia pipes 72 Metre 1678.07 120820.82

18.9.8 80 mm nominal dia pipes 36 Metre 2171.09 78159.40

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded fittings

32 18.9 This includes jointing of pipes & fittings with one step CPVC solvent cement,

trenching, refilling & testing of joints complete as per direction of Engineer in

18.9.5 40 mm nominal dia pipes 72 Metre 564.28 40628.38

Providing and fixing gun metal gate valve with C.I. wheel of approved quality

(screwed end) :

18.17.1A 20 mm nominal bore 5 each 541.13 2705.66

18.17.1 25 mm nominal bore 43 each 623.76 26821.81

18.17.3 40 mm nominal bore 3 each 827.91 2483.73

18.17.4 50 mm nominal bore 12 each 1028.90 12346.78

18.17.6 80 mm nominal bore 6 each 2610.25 15661.52

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with

plastic floats complete :

18.18.3 25 mm nominal bore 3 Nos. 465.07 1395.20

Providing and placing on terrace (at all floor levels) polyethylene water storage tank,

IS : 12701 marked, with cover and suitable locking arrangement and making per

necessary holes for inlet, outlet and overflow pipes but without fittings and the base litre

support for tank.

IV EXTERNAL SEWERAGE & RAIN WATER DRAINAGE SYSTEM

Excavating trenches of required width for pipes, cables etc. including excavation for

sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including

getting out the excavated soil, and then returning the soil as required, in layers not

exceeding 20cm in depth including consolidating each deposited layer by ramming,

watering etc. and disposing of surplus excavated soil as directed, within a lead of

2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm. 425 mtr 352.92 149991.51

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of

37 19.1 cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of

joints etc. complete :

Providing and laying Non pressure NP2 class (light duty) RCC pipe with collars

38 19.6 jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2

fine sand ) including testing of joints etc. complete.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded

39 19.2 stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as

per standard design:

Digitally signed by MAYANK

SL. NO Ref: DSR 2023 DESCRIPTION QTTY UNIT NET RATE AMOUNT

Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I.

grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300

mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not

less than 2.70 kg as per standard design

19.4.2 150 x 100 mm size P type

19.4.2.2 With Sewer bricks conforming to IS : 4885 20 Nos. 2717.64 54352.77

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand)

RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate

20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8

graded stone aggregate 40mm nominal size) inside plastering 12mm thick with

cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat

cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4

graded stone aggregate 20mm nminal size) finished with a floating coat of neat

cement complete as per standard design.

Inside size 90x80cms and 45cms deep including CI cover with frame (light duty)

19.7.1 455x610mm internal diamensions total weight of cover and frame to be not less

than 38 kg (weight of cover 23 kg and weight of frame 15kg).

19.7.1.1 With FPS bricks of class designation 75 (i) For Sewer Line 20 Nos. 12798.52 255970.35

42 19.8.1 Extra for depth for manholes:

Size 90x80cm with With common burnt clay FPS (non modular) bricks of class

designation 7.5

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement

43 19.15 concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm

nominal size) as per standard design

19.15.1 With 20x20 mm square bar 80 Nos. 545.89 43671.43

TOTAL FOR INTERNAL & EXTERNAL PLUMBING SYSTEMS 3273660.7 2952049.72

GROSS AMOUNT IN RUPEES 6225710.38

AMOUNT IN LAKHS 62.26

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS

AT SUSHMA SWARAJ INSTITUTE OF FOREIGN SERVICES MEA, BER SARAI, NEW DELHI

COST SUMMARY- FIRE PROTECTION ITEMS

S.No. DESCRIPTION OF WORKS DSR E&M 2022 AMOUNT MR AMOUNT

I PUMP AND FITTINGS 168139.65 1294.30

II PIPING AND HOSE REEL 263023.62 0.00

III FIRE EXTINGUISHERS 0.00 56187.75

DSR AMOUNT & NDSR AMOUNT 431163.26 57482.05

TOTAL (DSR AMOUNT + NDSR AMOUNT) 488645.31

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT SUSHMA SWARAJ INSTITUTE OF FOREIGN SERVICES MEA, BER SARAI, NEW

SCHEDULE OF QUANTITIES

FIRE PROTECTION WORKS

SL. NO DESCRIPTION QTY UNIT NET RATE AMOUNT

COST INDEX, CORRECTION FACTOR AND GST ALTERATION 1.065

I PUMP AND FITTINGS DSR-2022 MR

Supplying, installation, testing and commissioning of electric driven terrace pump

1 18.4 suitable for automatic operation and consisting of following, complete in all

respects, as required: (Terrace Pump)

(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body

& bronze impeller with stainless steel shaft, mechanical confirming to IS :

(b) Suitable HP squirell cage induction motor TEFC type suitable for operation

on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for

enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming

(c) M.S.fabricated common base plate, coupling, coupling guard, foundation

bolts etc.as required.

(d) Suitable cement concrete foundation duly plastered

and with anti vibration pads.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating

2 18.11 with bronze/gunmetal seat duly ISI marked complete with nuts, bolts,

washers, gaskets conforming to IS 13095 of following sizes as required:

Providing, installation, testing and commissioning of non-return valve of

3 18.14 following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts,

nuts, washers etc.as required

Providing, installation, testing and commissioning of stainless steel Y-strainer

4 18.15 fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia

holes with stainless steel flange

Providing, installation, testing and commissioning of stainless steel Y-strainer

5 18.23 fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia

holes with stainless steel flange

Providing, installation, of bourdon type pressure gauge with 0-20kg/cm2

MR-1 100 mm dial size 1 each 1294.30 1294.30

II PIPING AND HOSE REEL

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe

conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees,

flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling

7 18.7 with suitable clamp/support frame and painting with two or more coats of

synthetic enamel paint of required shade complete as required:

Supplying and fixing first-aid Hose Reel with MS construction spray painted in

post office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced)

type -2 as per IS: 12585

Digitally signed by MAYANK

FIRE PROTECTION WORKS

SL. NO DESCRIPTION QTY UNIT NET RATE AMOUNT

20 mm nominal internal dia gun metal globe valve & nozzle. Drum and

brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and

III FIRE EXTINGUISHERS

Supply of ABC (Stored Pressure type) duly ISI marked conforming to IS:

15683:2006 squeeze grip release valve, discharge pipe locking arrangement,

pressure gauge, operation manual, and bracket. Suitable for wood, paper,

9 MR cloth, plastic, diesel, petrol, paint, LPG, CNG, PNG, electrically started fire.

MR-2 Capacity 4 Kg. 9 Each 2817.00 25353.01

MR-3 Capacity 6 Kg. 9 Each 3426.08 30834.74

TOTAL FOR FIRE PROTECTION WORKS 431163.26 57482.05

GROSS AMOUNT IN RUPEES 488645.31

AMOUNT IN LAKHS 4.89

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT SUSHMA SWARAJ INSTITUTE OF FOREIGN

SERVICES MEA, BER SARAI, NEW DELHI

BOQ - LOW VOLTAGE WORKS

S.NO. REF. DESCRIPTION OF ITEMS UNIT QTY RATE AMOUNT REMARKS

Supply , Installation , Testing and commissioning of CAT 6 UTP cable 23 AWG LSZH as per

ANSI/TIA 568 C.2 and ISO/ IEC 11801–2nd Edition, ROHS Compliant, solid copper

conductors, tested @250 Mhz, with HDPE insulation of individual conductor and over all

Dia of 5.8mm for Connectivity of Hub room to End Point.

Supply, Installation, Testing & Commissioning of CAT 6 UTP Universal (both tool &

toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd

Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum

750 mating cycle and 200 insertion cycle and UL approved,for Camera at user end.

Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6 UTP, Transparent

3 MR LV 3 shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks Nos. 2 15956.18 31912.3519

and earthing plug for CAT6 cable termination at rack end.

Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per

4 MR LV 4 ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side Nos. 30 568.79 17063.5965

switch to jack panel connectivity.

Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per

5 MR LV 5 ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side Nos. 30 621.69 18650.7166

switch to end user connectivity.

Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style

with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS

Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002

AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side.

Supply, installation, testing and commissioning of 5 MP Dome camera , ONVIF profile S ,

G& T ,BIS , CE , FCC Certified ,1/2.7” Progressive Scan CMOS ,2.7 mm to 13.5 mm

motorized varifocal lens , Quad stream with each stream support H.265 compression

simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON ,

Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression : H.265/H.265+/H.264/H.264+

7 MR LV 7 .SD card support upto 256GB , Alarm trigger - 1 input / 1 output , frame rate : Main Nos. 18 44680.58 804250.476

stream should support 25 fps@5MP ,Edge analytics : Customer Flow staistics, Cross

COunt, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line

cross Detection. Queue length detection, Regional population statistics, SOD-Stationaary

Object Detection. , In built IR LED , IR Distance upto 45 meters , IP 66 ,IK10,POE.Audio -1

input/1 output.

Supply, installation, testing and commissioning of 5 MP Bullet camera , ONVIF profile S

,G & T . BIS , CE , FCC Certified ,1/2.7” Progressive Scan CMOS ,2.7 mm to 13.5 mm

motorized varifocal lens , Quad stream with each stream support H.265 compression

simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON ,

Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression :

8 MR LV 8 H.265/H.265+/H.264/H.264+/MJPEG .SD card support up to 256Gb, Alarm trigger - 1 input Nos. 2 45365.87 90731.734

/ 1 output , frame rate : Main stream should support 25 fps@5MP , Edge analytics :

Customer Flow staisticsCross Count, Heat Map, Human & Vehicle Detection, Pedestrian

Intrusion Detection & Line cross Detection. Queue length detection, Regional population

statistics, SOD-Stationaary Object Detection. , IR Distance upto 45 meters , IP 66 , POE.

Audio -1 input/1 output

Supply, installation, testing and commissioning of 32 channel NVR , ONVIF compliant ,

Certification CE,FCC,UL,BIS, recording bandwidth 320 Mbps , output interface 1 HDMI (up

to 4K), 1 VGA , Alarm in/out :16ch in / 4ch out , 1 X RJ-45 port (1000M) , Bit Rate 16kbps-

20mbps per channel, Sync Playback 4/8/10/16 ch playback, iOS smartphone support , 8

HDD support , each HDD slot support upto 8 TB HDD , , 1x3.0 USB for backup /upgrade ,

2x 2.0 USB for mouse, 1 E-Sata Port, Cloud Storage, Net HDD, Edge analytics : Customer

Flow staistics, Face Attendence, Face Detection and Recognition, Heat Map, Human &

Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection, Queue length

detection, Regional population statistics, SOD-Stationaary Object Detection, Deterrence,

PIR, Video tampering, AI Registerd Qty- 10000 & AI Captured Qty- 200000. Protocol

support:- HTTp, TCP/IP, IPv4, UPNP, RTSP,UDP,SMTP,NTP,DHCP,DNS,IP

filter,PPPOE,DDNS,FTP,IP search, P2P, NFS/SMB/CIFS, ONVIF.

Supply, Installation, Testing & Commissioning of 8TB Surviellance Hard Disk.

Supply, Installation, Testing and Commissioning of Full HD 55" LED Professional Display

Digitally signed by MAYANK

Supply, Installation, Testing & Commissioning of L2+ managed industrial PoE switch with

24*10/100/1000M RJ45 ports and 4*1/10G SFP+ fiber slot ports, Port 1-24 can support

IEEE 802.3af/at PoE standard, switching capaticy of 598 Gbps, forwarding performance

12 MR LV 12 95.23 Mpps, maximum PoE output power is 400W(at-600W), with 32K MAC address. Nos. 2 339442.22 678884.438

Should have Static Routing , system logging, Telnet, SSH2.0, SNMP V1/V2C/V3, Network

Time Protocol (NTP), FTP, TFTP, Xmodem.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-

3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ;

Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW,

13 MR LV 13 Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Nos. 1 97063.77 97063.7674

Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard

Drive; Operating system: Windows 7 Professional 64 Bit or latest.

Supply, Installation, Testing & Commissioning of Access Point 2x2:2 streams SU/MU

MIMO on 5GHz and 2.4GHz,AP should have one Ethernet port and one 2.5Gig port,

should support IEEE 802.11 a/b/g/n/ac/ax amendments. AP should provide 23 dBm EIRP

on 2.4GHz and 5 GHz, -93 dBm on 2.4GHZ and -98 dBm on 5GHZ receive sensitivity. AP

should have capacity to handle minimum 500 Concurrent devices. Should have IPv6

support, IEEE 802.1Q, Band balancing, airtime fairness. AP Should support

auth/encryption methods for WLAN configuration: Open, WEP, WPA2-AES, Unique PSK,

WPA3-SAE, WPA3-OWE, IEEE 802.1X/EAP, AAA, AES-GCMP-256. AP should be having

administration access through HTTPS GUI, SSH CLI, Should have operating temperature of

Digitally signed by MAYANK

NAME OF WORK : RENOVATION AND RETROFITTING OF CONVERTING 18 "D" BLOCK UNITS TO 32 UNITS AT SUSHMA SWARAJ INSTITUTE OF FOREIGN SERVICES MEA, BER SARAI, NEW DELHI

S.NO. REF. DESCRIPTION OF ITEM UNIT IMAGE QUANTITY RATE AMOUNT

A FURNITURE IN HOSTEL ROOMS

WARDROBE: 2 Door Wardrobe with internal Drawer

Providing and placing Wardrobe of size (W) 900mm X (D) 610mm X (H) 1980mm. with

openable door. Finishes and Material: The wardrobe is made from 18mm HDMHR board with 1mm

aprroved shade of laminate. The non exposed area will be cover up by 0.8mm balancer laminates. All the

exposed edges are with 2mm PVC egdebanding & sealed edges are with 0.8mm thick PVC Imported edge

banding. The shutters are sealed with 2mm thick PVC edge banding. Wardrobe is a combination of shelves,

1 MR 1 drawers & Hanging provision. Shutters are made of 18mm thick HDMHR board with 1mm aprroved shade each 33 31941.00 1054053.00

of laminate. The back is made of 8mm HDMHR board. All the exposed edges are with 2mm PVC egde

Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The wardrobe are

assembled by knock down fittings such as Minifix & Dowels.Final Design of the Materials must meet

standard specifications and be approved by Engineer-in-Charge/NBCC/Client/Cosultant/Architect prior to

Dressing Table: Providing and placing Dressing Table of size 660Wx450Dx1825H mm. with openable door.

2 Exteral drawer provided for storage. Drawers on Telescopic Channel. Handle are provided for easy

opening. Finishes and Material: The Dressing is made from 18mm thick HDMHR board with 1mm aprroved

shade of laminate.The non exposed area will be cover up by 0.8mm balancer laminates. All the exposed

edges are with 2mm PVC egdebanding & sealed edges are with 0.8mm thick PVC Imported edge banding.

2 MR 2 The shutters are sealed with 2mm thick PVC edge banding. 6mm Looking mirror pasted on shutter. Back & each 33 18236.00 601788.00

Drawer bottom are made of 8mm HDMHR board. All the exposed edges are with 2mm PVC egde Imported

banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The Dressing Table are

assembled by knock down fittings such as Minifix & Dowels. Materials must meet standard specifications

and be approved by Engineer-in-Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Queen Size Bed With Side Table- 1620Wx2070Dx1225H mm, 400x450x500mm

Queen size Bed with Bed Side Table (with Storage) with includes side Panel, leg board and head board

height(of size 1000 mm) made out of 25mm HDMHR with 1mm approved shade Laminate and The

mattress rest will be 18mm thick HDMHR. The Bed Side Table made out of 18mm HDMHR with approve

shade of 1mm laminate .It should be provided with a back panel made out of 6mm thickness HDMHR .It

should be provided with two drawer for storage. All pressing Laminate on to the HDMHR has be executed

3 MR 3 mechanically Hot press with polymersied D3 adhesive (Kleiberit/ Jowat / Henkel). The non exposed area each 33 69690.00 2299770.00

will be cover up by 0.8mm balancer laminates. All exposed edges should be mechanically edge banded

with PVC tape ( Rehau/Dolkan) & hot melt glue ( Jowat/ Henkel & kleiberit) . All hardware fittings will be of

Hettich/ Ebco make.It should have a knockdown arrangement of fitting. The design of the Queen size Bed

with Head board & Bed Side table is shown in the picture.Materials must meet standard specifications and

be approved by Engineer-in-Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Supplying and Placing of Mattress for above King Size Bed- 6" Thick, Fabric: Comfortable fabric to regulate

moisture and temperature, plush Quilt with double foam layer, with COMFORT LAYER Body Support foam

for optimum alignment and pressure release on a box top separation layer. SUPPORT LAYER Ortho Support

foam for that recommended firmness. Warranty: 7 Years minimum.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

SOFA 2 SEATER : Manufacturing, Providing and Placing/installing sofa set (Fabric with part exposed

wooden frame) . The skeleton of the sofa shall be made in 2nd class teak wood all the exposed portion

shall be provided with melamine polish of desired shade as approved. The skeleton section shall be of

section 70 x 38 mm. Bottom frame shall consist of section 75 x 38mm. All joints shall be tongued & groove.

The sofa frame should design to carry 130 kg per seater weight of person. The seat and back of the sofa

shall be supported with 12mm thick commercial plywood. The Cushion of seat shall be provided with 100

mm thick PU form sheet of density 40 kg/m3 in addition to this one layer of form in addition to this one

layer of form 25 mm thick have density 32 kg/m3 shall be pasted over 100 mm thick form. The back

support and arm of sofa shall be provided with 50 mm thick form of 40 kg/m3 and one layer of 25 mm

thick form of density 32 kg/m3 pasted over it with necessary adhesive. Complete assembly shall be

5 MR 5 upholstered with the fabric shall have combination of polyester, cotton and linen mix as per manufacturer each 32 56449.00 1806368.00

specification and 300-400 GSM. The bottom of sofa shall be finished with 100 gsm (Minimum) marking

cloth with necessary nail. The sample of form sheet, upholstery cloth, wood etc. shall be got approved

from engineer-in-charge. Cost of all operation like cutting, stitching, carpentry, operations, nails, adhesive,

upholstery cloth etc. complete. The necessary materials, joints of frame legs, buffers at bottom, T&P,

transportation, installation in the flats from ground floor to 25th floor level etc. complete are included in

the scope and nothing extra shall be payable.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

W-1850 x D-660 x H-910. Final Design of the Product to be approved by NBCC/Client.

Digitally signed by MAYANK

SOFA 1 SEATER : Manufacturing, Providing and Placing/installing sofa set (Fabric with part exposed

wooden frame) . The skeleton of the sofa shall be made in 2nd class teak wood all the exposed portion

shall be provided with melamine polish of desired shade as approved. The skeleton section shall be of

section 70 x 38 mm. Bottom frame shall consist of section 75 x 38mm. All joints shall be tongued & groove.

The sofa frame should design to carry 130 kg per seater weight of person. The seat and back of the sofa

shall be supported with 12mm thick commercial plywood. The Cushion of seat shall be provided with 100

mm thick PU form sheet of density 40 kg/m3 in addition to this one layer of form in addition to this one

layer of form 25 mm thick have density 32 kg/m3 shall be pasted over 100 mm thick form. The back

support and arm of sofa shall be provided with 50 mm thick form of 40 kg/m3 and one layer of 25 mm

thick form of density 32 kg/m3 pasted over it with necessary adhesive. Complete assembly shall be

6 MR 6 upholstered with the fabric shall have combination of polyester, cotton and linen mix as per manufacturer each 32 37633.00 1204256.00

specification and 300-400 GSM. The bottom of sofa shall be finished with 100 gsm (Minimum) marking

cloth with necessary nail. The sample of form sheet, upholstery cloth, wood etc. shall be got approved

from engineer-in-charge. Cost of all operation like cutting, stitching, carpentry, operations, nails, adhesive,

upholstery cloth etc. complete. The necessary materials, joints of frame legs, buffers at bottom, T&P,

transportation, installation in the flats from ground floor to 25th floor level etc. complete are included in

the scope and nothing extra shall be payable.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

W-1390 x D-660 x H-910. Final Design of the Product to be approved by NBCC/Client.

COFFEE TABLE: W-1200 x D-600 x H-450mm

Manufacturing, supplying and installing factory made centre table by 2nd class teak wood with melamine

polish and toughened glass at top. Centre table provided with four legs of designer circular shape of dia 75

mm in taper shape with minimum 40 mm as approved shape. The frame section shall be size of 75x38mm

with top section of size 75x30mm including moulding at edges and corners. The top glass portion shall be

10mm thick black toughened glass and making necessary rebate for fixing/holding the glass. The edges

shall be bevelled at the ends of glass as approved. The joints shall be groove and tenon with wooden pins.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

STUDY TABLE: W-900 x D-600 x H-750mm

Manufacturing, supplying and installing factory made Study table is made from 18mm HDMHR board with

1mm aprroved shade of laminate. The non exposed area will be cover up by 0.8mm balancer laminates.

Top made of 36(18+18)mm thickess. All the exposed edges are with 2mm PVC egdebanding & sealed edges

are with 0.8mm thick PVC Imported edge banding. The shutters are sealed with 2mm thick PVC edge

banding. Drawer with telescopic channel. handle provide for easy opening. Modesty panel made of 18mm

HDMHR board with 1mm aprroved shade of laminate. shutter for storage provided.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

STUDY CHAIR: Height: 95.2 cm, Width: 45.7 cm,Length: 58.4 cm

The chair features a mesh back supported by a PP frame, a cushioned seat, PP arms, and a nylon base with

nylon wheels. The chair includes a center-tilt mechanism and a gas-lift mechanism for adjustable seating.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

TV CONSOLE UNIT: (W) 1390mm X (D) 315mm X (H) 450mm.

Manufacturing, supplying and installing factory made TV unit is made from 18mm HDMHR board with

1mm aprroved shade of laminate. Ledge made out of 18mm HDMHR board with 1mm

approved shade Laminate.The non exposed area will be cover up by 0.8mm balancer laminates. All the

exposed edges are with 2mm PVC egdebanding & sealed edges are with 0.8mm thick PVC Imported edge

banding. The design of the TV Panel with Ledge is shown in the picture. 3 drawer storage to be provided

below Ledge. Drawers on telescopic channel.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Carrom Board Table with 4 chairs:

Material Hardwood frame - ( Teak Wood, Sheesham & Rosewood ), Plywood board, Board Size Standard -

29" x 29" (playing surface), Full board ~32" x 32", Board Thickness - 6 mm to 8 mm (for smooth rebound

and durability) Playing Surface Polished plywood, smooth and scratch-resistant. Frame Width - 2 to 3

inches (provides solid rebound). Border (Frame) Material Hard Wood with polished lacquer finish. Net

Pockets Four corner pockets with mesh or cloth nets Leg/Stand Height Adjustable or fixed at 26 to 30

inches, Overall Height (Board + Stand) ~30 inches from ground level, Carrom Chair Specifications, Material

11 MR 11 Hardwood or powder-coated metal frame with plywood or cushioned seat, Seat Height - 17 to 18 inches set 1 65044.00 65044.00

(ideal for standard carrom tables), Seat Size - 16" x 16" to 18" x 18"

Backrest Height ~12 to 14 inches (comfortable yet low to not hinder movement), Design Armless, sturdy,

lightweight, Weight Capacity ~100 kg minimum, Finish Polished wood or painted metal, Cushioning

(Optional) Foam-padded seat (1–2 inches thick) for comfort during long sessions, Level adjusters on table

legs for even playing surface, Protective corners (rubber or plastic) on table,

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Digitally signed by MAYANK

Chess Board Table with 2 chairs: Material - Solid wood ( Teak Wood, Sheesham & Rosewood ), Plywood

board, Board Size - 20" x 20" to 24" x 24" (for a standard 2.25" square chessboard), Square Size - 2" to

2.25" per square (tournament standard), Inlay Type - Wood inlay (light and dark squares made from Maple

& Rosewood or Boxwood),Top Thickness - 1" to 1.5" thick solid wood or plywood top with veneer, Height -

28" to 30" (standard table height), Edge Finish - Smooth beveled or rounded edges, Storage - Optional

built-in drawers for chess pieces or timer, Leg Design -Sturdy four legs or pedestal design, often carved or

turned, Weight ~15–25 kg depending on wood and design, Finish Lacquered or satin finish for durability

and elegance, Wooden Chess Chair Specifications, Material - Solid wood or wooden frame with cushioned

seat, Seat Height - 17" to 18" (aligned with 30" table height), Seat Dimensions - 16"–18" wide x 16"–18"

deep, Backrest Height - 12"–16" (for back support), Design Comfortable and ergonomic for long sessions,

Cushioning 1"–2" PU foam or fabric-covered seat and back, Armrests Optional (tournament chairs are

usually armless), Weight Capacity At least 100–120 kg

Finish Polished wood, matte or gloss finish, matching table design, Optional Features Felt pads under legs

to prevent floor scratches,

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Modular kitchen cabinets & Toilet Vanity with the carcass, shutters, and back ply made using 18mm and

6mm HDHMR OSL boards. The shutters and back panels will be finished with 1mm and 0.8mm laminates

respectively, ensuring a durable and elegant surface. All visible edges will be sealed with 2mm

edgebanding for a clean and refined look. Handles of size 100mm x 25mm will be included as standard.

The sink bowl, mixer, and granite countertop are not included and can be quoted separately based on your

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

SUB-TOTAL (A) 11900554.88

B OTHER AMENITIES

LED TV (32") : Supplying, installation & commissioning of 32-Inch HD AI Smart WebOS LED TV HDR 10,

Final Design of the Product to be approved by NBCC/Client.

Geysers: Supplying, installation & commissioning of 25 Litre vertical water heater, 5 star rating, Vertical

mounting Geyser.Final Design of the Product to be approved by NBCC/Client.

Electric Cattle: Supplying, installation & commissioning of 1250 watt, 1.20 litre, double layered cool touch

16 MR 16 outer body, 304grade rust resistant SS inner body with autho shutt off Electric Cattle., Nos 36 1857.00 66,852.00

Final Design of the Product to be approved by NBCC/Client.

RO for drinking water: Supplying, installation & commissioning of 8 stage Alkaline tech water purifier with

RO+UV+Alkaline boost test and taste adjuster.Final Design of the Product to be approved by NBCC/Client.

SUB-TOTAL (B) 16,86,916.00

C Common Areas

Supply, installation, and commissioning of Table Tennis board (2740x1525x760 mm) with 25 mm

laminated top, 25x50 mm frame, and DuPont polyurethane anti-glare finish. Includes net, wheels, and

other necessary accessories. Approximate weight: 128 kg. Materials must meet standard specifications and

be approved by Engineer-in-Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Supply and installation of standard carrom board with minimum 75x75 cm playing area, 1.5–2 cm thick

board, and 6 cm wide plywood/MDF frame with matte laminated surface and rounded corners. Includes

striker and coins, sturdy fixed or foldable legs (height 75 cm), and 2 mm edge finish with UV and water-

resistant coating. All materials to be as per approved specifications and make.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Supply and installation of standard chess board (40x40 cm) with 5x5 cm squares, made from high-quality

hardwood (maple or walnut) with smooth finish. Embedded magnets in squares for secure piece

placement. Set includes 32 wooden pieces (7.5 cm King, 4 cm Pawn, weighted base). Hinged board with

20 MR 20 storage compartment lined with felt. Board finished with clear protective varnish/lacquer. Compliance Nos 1 20721.00 20,721.00

with safety and quality standards. Materials as per approved specifications.Materials must meet standard

specifications and be approved by Engineer-in-Charge/NBCC/Client/Cosultant/Architect prior to

55"TV : Supplying, installation & commissioning of of 55-Inch Class 4K UHD LED Smart TV (2025 Model),

21 MR 21 Materials must meet standard specifications and be approved by Engineer-in- Nos 1 47029.00 47,029.00

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Washing Machine: Supplying, installation & commissioning of 9 Kg, 5 strar rated, Inverter Direct drive

technology, 6 motion DD, inbuilt heater, touch panel fully automatic Washing machine.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Dryers: Supplying, installation & commissioning of 5.5 kg, 5 star, front load fully automatic turbo cloth

dryer. Latest model of reputed company as per Make List

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

Common Room Chair :

The seat & back shall be made up of 12mm L Ply upholstered with high resiliance moulded polyurethane

foam 50mm thick having density 50kg/m³ with Suede Fabric / khaki leatherite tapestry 0.8mm thick 535

GSM and the back shall be made of upholstered with high resiliance moulded polyurethane foam 25mm

thick having density 50kg/m³ with Suede Fabric / khaki leatherite tapestry 0.8mm thick 535GSM. The seat

24 MR 24 and back shall be fixed with metal frame. The frame structure shall be loop support type made up of MS Nos 21 5808.00 1,21,968.00

CRCA chrome plated tubular pipe having cross-section area Dai with 12mm thick. The seat size shall be

430±10 mm (D) X 450±10 mm (W) and back size shall be 410±10 mm (W) X 400±10 mm (Ht) from seat.

Overall height shall be = 710±10 mm, overall depth = 650±10 mm & overall width = 620±10 mm.

Materials must meet standard specifications and be approved by Engineer-in-

Charge/NBCC/Client/Cosultant/Architect prior to procurement.

SUB-TOTAL (C) 972569.00

Digitally signed by MAYANK

D OUTDOOR GYM EQUIPMENTS

HEALTH WALKER : Supplying, installation, and commissioning of health walker (1300x610x1350 mm) with

2 M.S. pipe supports (127 mm dia, 3 mm thick), base plates (200 mm dia, 10 mm thick), foundation set,

25 MR 25 fasteners, and screws. Complete with primer and painting as per approved manufacturer's specifications. each 1 39077.00 39077

Equipment to be procured from reputed company as per make list, subject to approval from

consultant/architect/NBCC/Client.

HORSE RIDER: Supplying, installation, and commissioning of horse rider (1090x560x1065 mm) made of

M.S. pipe (127 mm dia, 3 mm thick) with base plates (200 mm dia, 10 mm thick) and foundation set.

26 MR 26 Complete with fasteners, screws, primer, and painting as per approved manufacturer’s specifications. each 1 29314.00 29314

Equipment to be procured from a reputed company as per the make list, after approval from

consultant/architect/NBCC/Client.

DUAL SKY STEPPER: Supplying, installation, and commissioning of dual sky stepper (1090x560x1065 mm)

made of M.S. pipe (127 mm dia, 3 mm thick) with base plates (200 mm dia, 10 mm thick) and foundation.

27 MR 27 Complete with fasteners, screws, primer, and painting as per approved manufacturer’s specifications. each 1 53676.00 53676

Equipment to be procured from a reputed company as per the make list, after approval from

consultant/architect/NBCC/Client.

TRIPLE TWISTER: Supplying, installation, and commissioning of triple twister (1775x1775x1474 mm) made

of M.S. pipe (127 mm dia, 3 mm thick) with base plates (200 mm dia, 10 mm thick) and foundation set.

28 MR 28 Complete with fasteners, screws, primer, and painting as per approved manufacturer’s specifications. each 1 33319.00 33319

Equipment to be procured from a reputed company as per the make list, after approval from

consultant/architect/NBCC/Client.

CROSS TRAINER: Supplying, installation, and commissioning of triple twister (1370x660x1755 mm) made of

M.S. pipe (127 mm dia, 3 mm thick) with base plates (200 mm dia, 10 mm thick) and foundation set.

29 MR 29 Complete with fasteners, screws, primer, and painting as per approved manufacturer’s specifications. each 1 53676.00 53676

Equipment to be procured from a reputed company as per the make list, after approval from

consultant/architect/NBCC/Client.

KNEE CHAIR: 6.Supplying, Installation and commissioning of tripple twister of size 736X838X1168 mm

made up of Main pipe of M. S. pipe 127mm diameter and minimum 3mm thick with base plates of

minimum 200mm diameter 10mm thick with foundation set of M.S. pipe 127mm diameter 3mm

thickness, base plates of suitable size and fixing with necessary fastners, screws, etc. complete with primer

and painting as per approved manufacturer’s specifications. The equipment should be procured from

reputed company as per make list after approval from consultant architect/NBCC/Client.

SUB-TOTAL (D) 239458.00

TOTAL AMOUNT (A+B+C+D) 14799497.88

TOTAL AMOUNT (A+B+C+D) 14799497.88

Digitally signed by MAYANK