REPAIR TO FLOORING, PLASTERING, SANITARY, PLUMBING, SUNKEN PORTION AND OTHER CONNECTED WORK INCL GUNITING AND GROUTING IN ZONE-III AND ZONE-IV AREA UNDER AGE B/R-II OF GE (I) KANPUR

Amount

Demolition of Stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Demolition of concrete in ground floors and paving n exc. 15cm thickness incl top finishing if exist at site (below or above ground level) un-reinforced concrete complete all as specified and directed.

M&L for cement concrete Type D2 (1:4:8) (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and in consolidation complete all as speified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 & ISI Marked of 60 mm thickness M-35 Grade with grey cement and pigment (Red & yellow) complete all as specified and directed.

M&L for cement concrete Type B0 (1:2:4) (using 12.50 mm graded stone aggregate) as in edging portion of paver block for proper matching with existing surface complete all specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in path / plinth protection / sub base finished the surfaces even & fair complete all as specified and directed.

Demolition of reinforced (reinforcement cut as required to faciliate demoltion) cement concrete of any description and any position not otherwise specifically provided for complete all as specified and directed.

M&L for Nominal mix Type B0 (1:1.5:3) (using 12.5mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors,chajjas, balconies, canopies, deck slabs and in shelves blocks etc and the like complete all as specified and directed.

S&F Formwork to side and soffits of floor and roof beam, beam haunching, girders, bressumers, lintels, cantilevers, shelves including supports, overhang,chajjas etc. also splays between floor and roof beam etc. for flat rough finished surface of concrete complete all as specified and directed.

M&L for MS TMT bars 05 mm dia and over upto and including 10 mm dia cut to length, bent to shape required as in stirrups, spacers and binder including cranking, bending spirally for hoping for columns, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9 mm dia or securing with clips complete all as directed and specified.

Demolition of brick work or stone/boulders masanory built in cement mortar including all quoins, arches, pillars etc, but excluding ashler facing, dressed stone work and precast concrete articals complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in built in cement mortar 1:6 complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in built in cement mortar 1:6 (except bricks i.e. by using old bricks after proper cleaning) complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for 25 mm thick PCC Type B-0 1:2:4 (using 12.5 mm graded stone aggregate) as in leveling /sub base of flooring complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for 400 x 400 mm Non skid ceramic coloured tiles of approved colour & 7-8 mm thick as in floors etc fixed with spacers(Light weight plastic of 3mm size) and epoxy grouting of joints mixed with pigment to match the shade of tiles over screed bed complete all as specified and directed.

M&L for 600 x 600 mm size 8 to 10mm thick polished Vitrified Ceramic tiles of approved colour as in floors etc fixed with spacers(Light weight plastic of 3mm size) and epoxy grouting of joints mixed with to match with shade of tiles screed bed complete all as specified and directed. Note:- Screed bed shall be measured and paid separately.

All as per item No 20 above but as in skirting & including 10mm thick rendering in CM(1:4) complete all as specified and directed.

M&L first quality coloured glazed ceramic, tiles fixed in pattern of different colour including border of size 300x450x7 mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid on and including 10 mm thick rendering in cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. Note :- Pattern of the tiles will be decided by GE at the time of execution.

M&L for 14-18 mm thick Granite (of approved colour) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and poilishing complete all as specified and directed.

Dismantiling of loose concrete by chiselling from RCC members like col, beam, parapet, facia, ceiling and also remove any existing treatment on RCC surface by rubbing, scrapping etc exposing the reinforcement without disturbing the reinforcement and get free from rust by sand blasting providing at places addl reinforcement welding with existing reiforcement as directed wherever required binding with welded mesh 100 mmx100mm (12 gauge welded mesh) & tack welding and primed with using Araldite epoxy resins ( manufactured by M/s Ciba Geigy Ltd/ FAIR BOND EP/Sika or other approved manufacture) & provision of guniting pressure 2 to 3 Kg/Sqm with admixer 1 cement 3 sand mixed Dr fixit Pidicrete SC plasticiser (2 to 10% by weight of cement) of thickness 40mm average including stripping, floating with wooden strippers for proper dimension control inclusing necessary form work & scaffolding up to Three storey complete and surface of guniting to be finished fair and even with and including 10 mm thick plaster in cement mortar 1:4 with water proffing compound @3% by weight of cement, cleaning & removing of waste material etc as directed at site including necessary painting, white wash, distemper/ exterior acrylic emulsion). All surrounding wall, joineries and fitting should be covered with polythene sheet by contractor while work. (Any wall, floor,fittings and roof damaged by the contractor shall be repaired/change by contractor under same item and no extra payment will be paid to contractor on this account complete all as specified and directed. Note: Welded mesh & addl reinforcement if required measured and paid separately.

M&L for Mild steel TMT bar 6 mm to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking end, binding wire (0.9mm dia annealed ) for rebaring complete all as specified and directed.

M&L welded steel wire fabric weight n exc 4 Kg/sqm complete all as specified and directed.

Taking down cement plaster on wall & ceiling including raking out joint, hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering of brick wall in CM 1:6 finished even & fair on other than fair faces up to ceiling height including required scaffolding etc complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick wall in CM 1:4 finished even & fair with using WPC up to G+2 height including required scaffolding etc complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for 10 mm thick cement plaster on ceiling in CM 1:3 finished even and smooth without using extra cement including required scaffolding complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L preparation of new surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for 1mm thick wall care putty on wall and ceilings complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coat of oil emulsion distemper/ acrylic washable distemper over and including a coat of primer over . The paint will be applied through aireless spray techonology with max working pressure of 3300 PSI by Trucare Graco machine / Airless paint sprayer (Vands Engineering solutions) / Airless sprayer machine Surya 9 (Jaguar) / Control Pro 190 Air paint sprayer (Wagner) and capable of operational single spray gun with a maximum materials hose length 150m working,complete all as specified and directed.

M&L for preparation of newly plastred surface of walls and applying two coat of exterior weather proof anti algae paint over and including a coat of primer. The paint will be applied through aireless spray techonology with max working pressure of 3300 PSI by Trucare Graco machine / Airless paint sprayer (Vands Engineering solutions) / Airless sprayer machine Surya 9 (Jaguar) / Control Pro 190 Air paint sprayer (Wagner) and capable of operational single spray gun with a maximum materials hose length 150m working,complete all as specified and directed.

Supplying and applying, two components acrylic polymer modified cementitious coating on new masonry surfaces devoid of plaster, with Hydrostatic resistance upto 5 bars with forced coverage of 1.75 Kg per Sqm in two coats using roller or brush with a gap of 4 to 6 hrs between the coats. The coats to be applied shall be perpendicular to each other complete all as specified and directed. Note : The Coverage is to be strictly maintained for film formation.

Taking up or down 40 mm dia steel tubing and connection including cleaning for refixing or removal complete all as specified and directed.

S&F GI steel tubing 40 mm bore medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete as specified and directed.

M&L for cement concrete (1:2:4) Type B0 (using 12.5mm graded stone aggregates) laid in slope towards drainage out spout pipe mixed with waterproofing compound as per manufacturer instructions drainage spouts shall be provided integrally while laying PCC.Fixing of spout shall be done with same PCC as in this item.

M&L for Preparation of plastered floor surface by cleaning surface free from dust and other foreign materials etc. and laying in repair Atatic poly propylene polymer modified membrane pre fabricated 3mm thick with non woven polyester matt central core of 160 gms/Sqm weighing not less than 3.5kg per sqm laid over and including primer conforming to IS 3384 @ 0.4 lit/sqm by using LPG/Butane torch and applying uniform pressure with a roller with overlap of 100mm in longitudinal direction and 150mm in transverse direction laid as per manufacturers instructions complete all as specified and directed.

M&L PCC 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in nfoundation filling and mass concrete complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore including fittings of any type and material complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connection including removal of fittings of any type and material complete and all as specified and directed.

Cutting chases, pinning in, in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring. etc. and making good, cutting not exceeding 10cm girth complete all as specified and directed.

S&F GI steel tubing 15mm bore medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete as specified and directed.

S&F GI steel tubing 20mm bore medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete as specified and directed.

S&F in repair 15mm bore bib tap long body, fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed.

S&F in repair 15mm bore angular stop valve chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore angle valves,fancy type two way chromium plated with long shank and cup screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm bore stop valves,fancy type chromium plated with long shank and cup (concealed type) screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15 mmPillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed

S&F in repair three in one system, with provision of both hand shower and overhead shower with 115 mm long bend pipe, connecting legs and wall flench and including maze hand shower 95 x 95 mm square shape single flow (Face plate stainless steel and ABS body in chrome finish) and overhead shower 200x200 mm square shape single flow (ABS body chrome plated with grey face plate) including all necessary arrangements complete all as specified and directed.

S&F of 15 mm bore, brass CP wall mixer two in one for mixing hot and cold water screwed down for iron pipe complete all as specified and directed.

S&F for 15 mm bore sink mixer chromium plated with swinging spout (wall mounted model) with connecting legs and wall flanges complete all as specified and directed.

S&F in repair 15 mm bore, brass CP WHB mixer for mixing hot and cold water screwed down for iron pipe complete all as specified and directed.

S&F in repairs for vitreous china wash basin white flat back size 550x400mm but exclusive taps, chain and plug and porcelain stopper but including cutting for and pinning in ends of brackets or erecting stand, waste pipes, pedestal & brackets complete all as specified and directed.

S&F 15mm bore PVC connection 600mm long heavy duty with brass fly nut and washer for hot and cold water complete all as specified and directed.

S&F in repair 10 ltrs capacity low level PVC dual flushing cistern, valveless, syphonic type, white,with inlet,ball float and handle including brackets complete all as specified and directed.

S&F in repairs WC squatting pan “Orissa Pattern” of size 580 x 440 mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding including S&F trap set complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan cascade type white incl. seat cover and flushing cistern dual action type as per manufacturer instructions with all fittings complete all as specified and directed.

S&F in repair vitreous china wash down water closet pedestal pattern white with plastic seat cover (excluding fixing of bolt of flushing cistern and flush pipe) including all fitting complete all as specified and directed.

S&F Soap dish, chromium plated incl fixing with connected accessories complete all as specified and directed.

S&F in repair corner glass shelf chromium plated grills & toughened glass base complete all as specified and directed.

S&F wall mounted towel rack chromium plated 600 mm including fixing with connected accessories complete all as specified and directed.

S&F in repair Towel ring chromium plated dia not less than 15 cm with mounting brackets complete all as specified and directed.

S&F in looking Mirror 6.00mm thick in decoratied frame , screwing with high quality ss glass fixer / holder sleeves at corners complete all as specified and directed.

S&F 15 mm dia & 1m long flexible SS braided cord health faucet incl chromium plated wall hook fixed to wall complete all as specified and directed.

S&F in repairs Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F stainless steel plate rack made out of 1mm thick stainless steel of overall size 750x900mm including fixing with brackets/clamps with screws pattern & design as approved by GE complete all as specified and directed.

Dismantling PVC water tanks and remove to store capacity exc 250 Ltrs and n exc 500 Ltrs complete all as specified and directed.

S&F HDPE triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 litres capacity hoisted and fixed in position including for hoisting into position either inside or outside of building, connecting up pipes, securing access cover etc including float valve, Cover, GI nipple of suitable size complete all as specified and directed.

Dismantling PVC water tanks and remove to store capacity exc 500 Ltrs and n exc 1000 Ltrs complete all as specified and directed.

S&F HDPE triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 litres capacity hoisted and fixed in position including for hoisting into position either inside or outside of building, connecting up pipes, securing access cover etc including float valve, Cover, GI nipple of suitable size complete all as specified and directed.

S&F in repair 20mm dia Gun metal globe or gate valve with iron wheel head, screwd both ends for iron pipe complete all as specified and directed.

Dismantling of 75 to 100 mm dia CI pipes/fittings jointed in cement mortar fixed to wall or laid in trenches and taking out if required complete all as specified and directed.

Supplied and fixed CI soil waste & vent centrifugally cast spun pipe in any length with or without ears, with cement joints 100 mm bore laid in floor/trenches complete all as specified and directed.

Supplied and fixed CI soil waste & vent centrifugally cast spun pipe in any length with or without ears, with cement joints 100 mm bore laid on walls with MS flat iron clamps with 50x6mm and 16mm dia round bar stay of required shape and size inclduing drilling holes and embedded in CM 1:3 surface finished complete all as specified and directed.

Supplied and fixed CI soil waste & vent centrifugally cast spun pipe in any length with or without ears, with cement joints 75 mm bore laid in floor/trenches complete all as specified and directed.

Supplied and fixed CI soil waste & vent centrifugally cast spun pipe in any length with or without ears, with cement joints 75 mm bore laid on walls with MS flat iron clamps with 50x6mm and 16mm dia round bar stay of required shape and size inclduing drilling holes and embedded in CM 1:3 surface finished complete all as specified and directed.

S&F in repairs cast iron floor trap of 75 mm dia, chromium plated grating including jointing to waste pipe with lead joints and fixed in cement concrete 1:2:4, type B1 (using 12.50 mm graded stone aggregate) complete all as specified and directed.

S&F cast iron branch pieces 100mm bore, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F cast iron branch pieces 75mm bore, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F 100mm dia CI bend (any radius) with oval access door diminshing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 75mm dia CI bend (any radius) with oval access door diminshing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F CI vent cowl of size 75mm / 100 mm dia complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) rain water pipes single socketed in any length with rubber ring joints 110mm bore fixed to walls PVC projected brackets and proper fixing with cement grout on terrace complete all as specified and directed.

S&F PVC (SWR) bends any radius 110 mm bore fixed with rain water pipe complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutters from the frame) n. exc 1.5 sqm including making good dismantled portion by brickwork, concrete (1:2:4) or CM(1:3) and plastering complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm n exc 4 sqm including making good dismantled portion by brickwork,cement concrete (1:2:4) or CM(1:3) and plastering each complete all as specified and as directed.

S&F Powder coated minimum powder coating of thickness 50 micron aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F in repair Powder coated minimum powder coating of thickness 50 micron aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. hydraulic door closer complete all as specified and directed.

S&F powder coated minimum powder coating of thickness 50 micron aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (01 Nos) hinge type B-21 100mm long (2 Nos) suitable handle (2 Nos) and tower bolts complete all as specified and directed.

All as per item No. 94 above, but wire gauzed window, complete all as specified and directed.

S&F 5 mm thick tinted glass each panes of any size fixed on aluminium door shutter with and including aluminium beading, rubber gasket etc. complete all as specified and directed.

S&F in repair 3 mm thick shhet glass panes any size fixed on door/ window shutters with and including beading/ putty/ rubber gasket etc. complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of decorative type/wood grain printed colour of size 50 X 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

All as per item No 100 above, but size 65 x 125 mm complete all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid type/ Plain flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade),calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant & fixing with stainless steel butt hinges on door with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) incl. wire cloth consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded decorative type/wood grain printed colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; wire gauzed i.e. panel will be of wire gauze in lieu of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly of wood grain printed colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900) used instead of exposed portion of PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site using stainless steel butt hinges complete all as specified and directed. Note : Wire cloth used shall be of 0.36 mm nominal dia and average width of aperture 1.40mm.

S&F stainless steel butt hinges of size 100mm fixed to door shutter with SS screws incl. other necessary acessories complete all as specified and directed.

S&F 200mm stainless steel fancy handle of approved make fixed with SS screws etc. complete all as specified and directed.

S&F 200 mm stainless steel barral tower bolt of extruded section complete all as specified and directed.

S&F 250 mm Stainless steel sliding door bolt with hasp and staple(bolt type) including fixing with necessary accessaries complete all as specified and directed.

S&F 200mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 75mm long stainless steel door stopper of double legged with rubber shoes in bottom complete all as specified and directed.

M&L for taking down and refixing the door shutter with frame in same opening after Easing of door / window shutters of any size / any number of panels for easy closing / opening tightening of hinges or changing the position of hinges adjustments of tower bolts, sliding bolts etc complete all as specified and directed.

S&F in repair 250 mm Stainless steel sliding door bolt with hasp and staple(bolt type) including fixing with necessary accessaries complete all as specified and directed.

S&F in repair 200mm stainless steel handle of approved make fixed with SS screws etc complete all as specified and directed.

S&F in repair 200 mm stainless steel barral tower bolt of extruded section complete all as specified and directed.

S&F in repair stainless steel butt hinges of size 100mm fixed to door shutter with SS screws incl. other necessary acessories complete all as specified and directed.

S&F framed work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F MS 125mm Butt hinges, heavy weight, cold rolled mild steel into MS frame for caging work etc throgh spot welding complete all as specified and directed.

Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) 3 track sliding Window with mesh shutter - (2-glass shutter and 1-mesh shutter) duly manufactured using UPVC reinforced profiles (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin) of (108 mm x 45 mm) x 2.20 mm for outer frames, (39 mm x 58 mm) x 2.20mm for sliding shutter frames capable of mounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum through fusion welding. The window sash shall be fitted with 5 mm thick clear float glass of reputed make and thickness of 1.0/1.2 mm prefabricated & welded mesh shutter frame shall be (39 mm x 58 mm) x 2.0 mm fitted with Vinyl Coated Fiber mesh- on rollers/ pulley duly fixed with Grey colour TPV Gasket for sash & Glazing bead shall be co-extruded with Grey colour soft PVC. Window shall be provided with standard hardware & Single point locking system of touch Lock system. the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work. NOTE: Cost of ss wire mesh and 5mm clear glass is deemed to be inclusive in this item.

S&F factory made uPVC white colour casement (Openable) glazed / gauzed window with provn of AC opening as per design approved by engr-in-charge. window to be made of extruded profiles with wall thickness of 2.3mm (+ 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware. EPDM gasket 1.2 + 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of'zinc alloyed (white powder coated) and 5mm float glass. NOTE: (i)Cost of ss wire mesh and 5mm clear glass is deemed to be inclusive in this item. (ii) Net opening will be measured for payement purpose.

S&F, stainless steel curtain rods of 25mm dia as in doors/ windows SS brackets fancy type including screws and other necessary fitting(knob) for fixing brackets SS Funnels for 25 mm dia dropry rods, fixed at each end of rods complete all as specified and directed.

Dismantling of boarding, any descripsion, fixed in any position with nails complete all as specified and directed.

S&F PVC board of thickness 18mm with decorative choice lamination on one side and plain colour on other, having minimum density of 600 gm/cm3,Lead Free,Anti-Bacterial & Anti-Fungal,Termite & Borer Proof & Water Proof including cutting, screwing as in kitchen cabinet, almirah shutter also matching the sawn edges using same colour PVC edge band tape complete all as specified and directed.

M&L 150mm size stainless steel handles of design approved by GE complete all as specified and directed.

S&F of continuous piano hinges brass bright finish or electro galvanised width of flaps when open in 30 mm complete all as specified and directed.

S&F Magnetic catcher heavy duty of approved quality in cupboard / wardrobs including fixing with necessary screws complete all as specified and directed.

S&F Telescopic channels for fixing for SS buckets for modular kitchen complete all as specified and directed.

S&F for Stainless steel tray, bucket and baskets of suitable shape and size for modular kitchen, fixing as per manufacturer's instructions complete all as specified and directed.

Dismantling of terracing tiles/brick tiles in single layer on roof,laid bedded and pointed in any mortar complete all as specified and directed.

Demolition by using hand held electric drills, cutting machine, chisels etc (direct use of hammers on RCC roof for demolition is strcitly prohibited) of roof treatment including padding concrete of any description and mud in roof any thickness with and including roughening old concrete surfaces by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L for cement concrete type B0 (1:2:4) (using 12.5 mm graded stone aggregate) as in padding and coping,incl hunching, benching etc complete all as specified and directed.

M&L for 10 mm thick in CM(1:3) rendering on fair faces concrete surfaces / roof top mixed with liquid water proofing compound finished even & smooth without using extra cement complete all as specified and directed. Note : Liquid WPC shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L roof kerb of cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregates) mixed with and including SBR ploymer as manufacturer's instructions all around periphery of the wall complete all specified and directed.

M&L preparation of newly plastered sufaces of roof including cleaning the surfaces by using wire brush / pressure hose and applying high performance polyurethene liquid membrane waterproofing coating cold applied in two coats @ 1.5Kg /Sqm/ 2 coats spray (minimum or as per manufacturer instructions)/ brush applied, with an elongation of 300% to 700% and tensile strength of not less than 1.5 N/Sqmm as per ASTM D412 and ASTM D2370, crack bridging abiltity of 3.5mm as per ASTM C1305, shore a hardness of not less than 60 as per ASTM D2240. The item includes applying epoxy primer @ 0.15Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet, complete as per manufacturer's instructions complete all as specified and directed. Note: 1. The contractor shall submit a gurantee of 10 years from the date of completion of work for waterproofing treatment alongwith manufacturer's gurantee. The amount of Rs. 40 ( Forty ) per Sqm and min of Rs. 4000/- for waterproofing treatment shall be withheld from contractor's final bill till the expiry of gurantee period. The contractor at his own option may furnish fix deposit receipt pledged in favour of GE(I) Kanpur against guarantee money. 2. The water proofing shall be carried out by authorised applicator of manufacturer. The name of applicator shall be got approved from GE before commencement of work.

M&L for grouting using polymer modified waterproof grout.The detail procedure of inject grouting is as under: (i) Drilling of 12mm dia holes upto 40mm depth and provide PVC nozzles/ entry ports over grid@ 1m c/c or less depending upon situation. (ii) Before injecting the grout compressed air to be blown to remove all dist and dirt. (iii) Grouting atpressure of 5kg/sqcm to be don till refusal/ rejection or appearance of grout from adjacent nozzle. (iv) Observe the cracks and make V groove along. (v) Nozzles and V groove shall be filled with polymer based mortar.

Removing of demolished meterial to a distance of exc 100m and n exc 200m or under including loading, unloading complete all as specified and directed

M&L for preparation of old painted surfaces of iron and steel based materials of any description not other wise described over 10 cm width or girth and applying one coat of Synthetic Enamel paint (any colour) complete all as specified and directed.

M&L Painting to wood and wood based surface of any description over 10cm width or girth including one coat of synthetic enamel paint on old surface including preparation complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat of zink chrome red oxide primer complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410 W (Gde-E-250) quality A complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F of Pre- painted galvalume aluminum zinc coating GI based profile sheet TCT with gsm -150 sheet 0.50mm thick of any colour total mass coating 150gms/sqm (both side) and having tensile strength of 550 Mpa as in roof covering/cladding to wall/window chajja, fixed with self tapping screws complete all as specified and directed.

JOG CONSTRUCTION (BID ID -3388913)

ARORA BROTHERS (BID ID -3396809)

RAJA RAM AND COMPANY (BID ID -3397070)

J.B.ENTERPRISES (BID ID -3389115)