Construction of 96 HIG flats at CIT nagar

Amount

Mobilization of pile rig and its related equipments, bringing into site of all plant and machinery along with accessories etc., including transportation and Installation of vertical cast in situ bored piles of 450 mm, 500 mm, 600mm diametre using reinforced cement concrete Design Mix M30 Grade using 20 mm gauge hard broken stone jelly by settinng the bored cast in situ pile equipments with all accessories and tools at each locations based on the sequence of operations as directed by the departmental officer,boring for the piles from ground level in all soils to the required depth below cut off level to carry a safe working load not less than specified, by Direct Mud Circulation Method ( using bentonite clay of required density) inclusive of pile accessories, temporary casing pipe,bentonite solution of 10% of concrete with required density,mobilisation,transferring,instalation of pile driving accessories from one location to another,pile concreting inside of drime method pipe fitting, including removal of mud and slurry away from the scheme site but excluding the cost of steel and fabrication reinforcement grills but including Bentonite solution machinery charges labour charges etc.,all complete, complying with relevent standard specification and as dircted by the departmental officers. ( pile shall be measured from the top of the shoe to the bottom of the pile cap.) Design Mix M40 Grade concrete should be prepared with ordinary Portland Cement with water cement ratio not exceeding 0.45 including the use of Plasticizer of required Grade and Hard Granite Stone Jelly of 20mm size and downgraded as per requirement. a) conducting routine pile test for one and half times the safe load for every 1 in 100 piles, as per IS code and as directed by the Departmental Officers and b) Charge for chipping of pile wherever necessary to the required depth. c)Concrete for all piling work should be of Design Mix M30 grade with minimum cement content of 400 Kg per Cubic Metre and as directed by the departmental officers.

450mm Dia Pile

500mm Dia Pile

600mm Dia Pile

Earthwork excavation in all stiff clay, stiff back cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders and to the required depth as may be directed except in hard rock requiring blasting inclusive of shoring strutting and baling out water wherever necessary, depositing the surplus earth in places shown clearing and levelling the site with an initial lead of 10 metre and lifts as specified hereunder etc., all complete in all respects complying with relevant standard specification (including refilling)

0-2m Depth

2-3m Depth

Supplying and filling in foundation and basement with quarry dust in layers of 300mm thickness well watered rammed and consolidated complying with relevant standard specifications including cost of filling M Sand as directed by the Departmental officers.

Refilling in foundation and basement and other similar works with excavated earth in layers of 150mm thickness well watered rammed and consolidated complying with relevant standard specifications as directed by the Departmental officers.

Cement concrete 1:4:8 ( One of cement, four of M Sand and eight of hard broken stone jelly) for foundation and flooring using 40 mm size broken stone jelly inclusive of shoring, strutting, baling out water wherever necessary ramming, curing etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers.

Providing and laying in position , standardised concrete mix M30 Grade in accordance with IS 456-2000 using 20mm and down graded hard broken granite jelly for all RCC items of works with minimum cement content of 440 kg/m and maximum water cement ratio of 0.40, including admixture (plasticiser / super plasticiser) in recomended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about(5.0 cum) 7730 KG OF 20mm machine crushed stone jelly with about (3.3 CUM) 5136 kg of 10 -12mm machine crushed stone jelly with about(4.79 CUM) 7670 kg of M sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering including laying,manufctured in fully automatic batching plant and transported to site of work in transit mixer for all leads, vibrating with mechanical vibrators , finishing, curing, etc., and providing fixtures like fan clamps in the RCC Floor / RCC slabs wherever necessary without claiming extra etc, complete complying with standard specification and as directed by the department officers. the coarse and fine aggregates to be used should comply with the requirements of IS standards (No seperate payment will be made by the department for the excess usage of materials) and as directed by the departmental officers.

Foundation & Basement

Stilt Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Terrace Floor

Providing form work for reinforced cement concrete works using M.S.sheet of size 90x60cm and MS 10 guage stiffened with M.S. angle of size 25mmx25mmx3mm for boarding laid over silver oak (C.W.) joist of size 10cmx6.50cm (spaced about 90cm c/c) and supported by casurina post of 10cm to 13cm dia (spaced about 75cm c/c) etc., including strutting up to 3m height and removing the same after a specified period without damaging the RCC works in all floors complying with relevant standard specification and as directed by the Departmental Officers.

For Foundation Raft , Plinth Beam, Raft Beam Etc.

Small Quantities

Vertical Wall

Plain Surfaces

Cement concrete 1:5:10 ( One of cement, five of M Sand and ten of hard broken stone jelly) for foundation and flooring using 40 mm size broken stone jelly inclusive of shoring, strutting, baling out water wherever necessary ramming, curing etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers.

Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications for preparing the area for treatment by spraying chemicals and other incidental charges etc.. complete. The rates should be for antitermite treatment from the plinth beam and brick masonry with super structure in contact with the back fill earth and at the junction of the walls. The top surface of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide “Chloripyrifos” and spraying the same termicide solution on the wooden frames and treating the other periphery of buildings etc., complete in all respects as per IS 6313 (part II) / 1981 and as directed by the departmental officers.

Brick work in cement mortor 1:6 ( One of cement and Six of M Sand) using chamber burnt second class stock bricks of size 9"x 4 3/8"x 2 3/4" having minimum average crushing strength of 50Kg/sqcm in foundation & basement including dewatering wherever necessary proper setting curing etc., complete in all respects complying with relevant standard specifications and as directed by the Departmental Officers.

Foundation

Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor / Terrace Floor

Brick partition wall in cement mortor 1:4 ( One of cement and four of sand) 70 mm thick for superstructure In Following Floors using fly ash bricks of size 230 x 110 x 70 mm having minimum average crushing strength of 50Kg/sqcm. including curing etc. complete in all respects complying with relevant standard specifications and drawings and as directed by the departmental officers.

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Plastering in C.M 1:3 (one of cement and three of M M Sand)10mm thick for bottom of sunshade, ceiling in all floors, including scaffolding, curing ,finishing etc complete in all respects complying with relevant standard specifications and as directed by the departmental officers..

Plastering with cement mortar 1:5 ( One of cement and five of M M Sand) 12mm thick finished with neat cement including, providing band cornice scaffolding curing etc., complete complying with relevant standard specification and as directed by the departmental officer

Supplying and fixing of Best Indian teakwood wrought and put up for frames of doors including thress hold plate for front door and windows ventilators cup board and for any other similar joinery works with necessary plugs, rebates for shutters plaster grooves on all faces etc., including labour charges for fixing hold fasts complying with relevant, standard specifications etc., complete in all respects and as directed by the departmental officers.

up to 2.00m Height

2.00 to 4.00M Length

Supplying and fixing of Mild steel hold fast horizontally twisted of size 230 x 40 x 4mm with a pair of suitable Iron screws of approved quality complying with relevant standard specification and as directed by the departmental officers.

Supplying and fixing of Best Indian teakwood wrought and put up for frames of doors including thress hold plate for front door and windows ventilators cup board and for any other similar joinery works with necessary plugs, rebates for shutters plaster grooves on all faces etc., including labour charges for fixing hold fasts complying with relevant, standard specifications etc., complete in all respects and as directed by the departmental officers.

a) Single leaf door 120x210

b) Single Leaf Door Shutter 90x210

Supplying and fixing wood polymer composite board solid door frame and 25mm thick shutter frame corners of extruded outer size 75mm X 50mm the inner core more rigid WPC composite with minimum shore hardness of 55 and bulk density 0.8 Grams per cubic centimeters. The frame shall be fixed to the wall using 10 X 100 mm long MS screw through the frame through the pvc fastener. Minimum three numbers of screw to be provided for each vertical member. The overall size of frame shall be with suitable rebate for housing shutter and shutter consist of 25mm polymer composite board single core exhaust with one side embo printing design. To avoid duplicate from the printing design shall have logo of the WPC board shall be bount aid proved by kept official. The shutter shall be provided with 3 Nos of 4” SS butt hinges, 2 Nos of 4” Stainless Steel handles, 3 Nos of 6” Stainless Steel tower bolts with required Stainless Steel screws including labour charges for fixing the shutter frame, shutter and furniture fittings in position and finished smooth with template etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officers

Supply and fixing of UPVC glazed window and ventilators made out of hollow multi-chambered UPVC sections having isolated drainage and reinforced with galvanized steel. The concerns and joints shall be mitre cut and fusion welded. The outer frame of the window shall be made out of UPVC sections having an overall size of 60mm x 60mm x 40mm having wall thickness of 2.3mm, + or - 0.3mm and provided with steel reinforcement at a hardware locations and size of 27mm x 21.5mm. The fixed mullion shall be made out of UPVC sections having an overall size of 76mm x 60mm x 36mm having wall thickness of 2.3mm + - 0.3mm. It os also reinforced with steel reinforcement at a hardware location and size of 27.5mm x 17mm. The shutter frame shall be made out of UPVC sections having an overall size of 78mm x 60mmx38mm having wall thickness of 2.3mm + - 0.3mm and provided with steel reinforcement at a harware location and size of 25mm x 34.5mm. The glazing provided shall be of 5mm thick.

UPVC Window

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round theframes. The ventilator should be got approved from the Executive Engineer before use on work

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-olasticized polyvinyl chloride (uPVC) sections. Profiles:The profiles should be three chamber system which provides high insulation properties with outer frame 60mmx55mm with an outer wall thickness of 2.4mm.The window unit should be designed with all corner joints mitred and fusion welded.Windows should be steel reinforced with 25x24x25mm steel reinforcement with a thickness of 1mm to have dimensional stability.The sash should be of 60x102mm.The mullion should be of 60x74mm.The profiles should have co-extruded seals. Hardware: All the hardware like friction stays , handles should be screwed with self trapping screws.The handles,locks should be designed so that they cannot be released from outside. Glazing : The window system should be glazed 5mm plain float glass/600 bison lam Installation : The profiles should be cut to length and welded 45 degrees.The window should be designed such that the water drainage does not pass through the reinforcement chambe.The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug, etc all complete in all respects with relevant standard specifications and as directed by the departmental officers.

Supplying and fixing of magnetic door catches of best quality including cost of all materials and labour charges etc all complete Complying with relevant standard specifications and as directed by the Departmental officers.

Supply &fixing of Mild steel grills of approved quality including bending, welding, filing fixing in position with necessary screws, plugs, one coat of red oxide primier of approved quality, labour charges for fixing etc all complete complying with relevant standard specifications and as directed by the departmental officers (The design of grills should be got approved from the EE before use).

Supplying and erecting of pull and push type manually operated Rolling Shutter of approved size and section using 18 guage G.I. Sheet confirming to ISI standard with Hood covers including one coat of approved primer transport charges etc. complete in all respects, complying with relevant standard specifications and as directed by the departmental officers (The Model/Brand of the Rolling shutter has to be got approved by the EE before fixing).

Brick work in cm 1:4 (one of cement and four of M Sand) using chamber burnt second class ground moulded stock bricks of size 9”x4-3/8”x2-3/4” (23x11.2x7cm) for stair case steps including laying, proper setting, scaffolding, curing etc., complete in all respects in all floors complying with relevant standard specification and as directed by the departmental officers..

Providing cuddappa slabs of 18 to 20 mm thickness for cupboards, wardrobes .shelves,of well polished on both sides smoothly including fixing with CM 1:3 (one of cement three of M Sand)12mm thick including cutting to the required size laying fixing in position and jointing with black oxide and finishing neatly etc. complete all complying with relevant specificartions and as directed by the departmental officers.(The Brand and quality of slab should be got approved from the EE before use) in the following floors

First Floor to Fourth Floor

Supplying and fixing in position of colour Vertified DOUBLE CHARGED TILES Floor tiles of 800x800x10mm of approved special quality of 6mm thickness laid in cement mortar 1:3( One of cement and three of M Sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers.Note:( The colour and quality shall be approved from the E.E before use only one particular size of ceramic wall tiles to be used for one building)

Supplying and fixing in position of colour Antiskid floor tiles of any size of approved special quality of 6mm thickness laid in cement mortar 1:3( One of cement and three of M Sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers. Note:( The size, colour, make and quality shall be approved from the E.E before use only one particular size of ceramic wall tiles to be used for one building)

Supplying and fixing in position of colour glazed wall tiles of any size 6mm thickness laid in cement mortar 1:2( One of cement and two of M Sand) 10mm thick for wall facing / dadoing ,skirting over the plastered surfaces including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers. Note:( The size, colour, make and quality shall be approved from the E.E before use ) Note: ( only one particulars size of ceramic wall tiles to be used for one building)

Weathering course with broken brick jelly lime concrete using 20mm gauge broken brick jelly in pure slaked lime ( no M Sand) over roof slab to the proportion of brick jelly to lime ( Fat lime) being 32: 12 1/2 by volume well beaten with wooden beaters, for giving the required slope and thickness complying with relevant standard specification and as directed by the departmental officers.

Finishing the top of terrace floor with one course of solar reflective water proof, heat proof, cool proof tiles of size 300mm x 300mm x 8mm of approved quality laid in cement mortar 1:3 (One part of cement and three part of M Sand) mixed with chemical mineral powder (60 kg for 1000 Sqft) (before laying tiles, the tiles should be dipped with salin based nano liquid) and top pointing with cement mortar 1:3 (One part of cement and three part of M Sand) mixed with white cement, silicon powder and polymer additives (20Kg of 1000 Sqft) and joint pointed with a base concrete of PCC 1:2:4 using 6 to 10 mm metal for providing necessary gradient at top of roof etc., complete complying with standard specifications including cost of all materials, labour charges for lifting to open terrace, laying and finishing and other incidental charges etc., complete and as directed by the departmental officers. (The Brand and quality of tiles should be got approved from the Executive Engineer before using)

Painting the ceiling with two coats of approved Pale Milk White Plastic Emulsion paint over one coat of primer over Cement Plastered ceiling surface including cost of brushes, emulsion paints curing etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality of paint should be got approved by the Executive Engineer before use).

Providing and applying best approved quality ready made putty two coats of 2mm thick over the plastered surfaces to have even and smooth surface to receive the painting inculding cost of all materials , burshes, labour charges etc., complete in all respects complying with relevant standard specification and as directed by the departmental officer ( The quality and shade of putty should be got approved by the Executive Engineer before use).

Painting the walls two coats with approved plastic emulsion paint over one coat of primer including cost of brushes, paint scaffolding, etc., complete in all respects complying with relevant standard specification and as directed by the departmental officer ( The quality and shade of paint should be got approved by the Executive Engineer before use).

Painting the new walls two coats with best approved quality weather shield exterior emulsion paint over one coat of primer including cost of brushes, emulsion paints scaffolding curing etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality and shade of paint should be got approved by the Executive Engineer before use).

Painting the new wood work two coats with best approved gopal varnish etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality of varnish should be got approved by the Executive Engineer before use).

Painting New Iron work two coats with best approved Ist class synthetic ready mixed enamel paint of approved quality etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality and shade of paint should be got approved by the Executive Engineer before use).

supplying and fixing of best approved polished JET black granite slab 20mm thick laid in cement motar 1:3 (One of cement and three of M Sand) in all the floors over the hearth slab including cutting the granite to the required size wherever necessary, nosing the edges to the required shape, laying, polishing etc., all complete complying with relevant standard specifications and as directed by the departmental officers.(Measurement will be taken including bearing into walls also. The quality and colour of granite slab shall be got approved from the EE before use).

Supplying and fixing Stainless Steel sink of size 90 x 45 x 20 cm having thickness of not less than 1mm well polished smoothly with necessary C.I .clamps ,screws, etc all complete LIKE DIAMOND, NIRALI complying with relevant standard specification and as directed by the departmental officers . (The quality and brand of Stainless steel sink should be got approved from Executive Engineer before use).

Providing 150mm,75mm and 50mm thick wide band with cement mortar 1:5 ( One of cement and five of sand) 12mm thick finished with neat cement including, scaffolding curing etc., complete complying with relevant standard specification and as directed by the departmental officers.

150 mm wide Border

75 mm wide Border

50 mm wide border

Supplying and fixing of 160mm dia PVC soil pipe of PVC SWR Pipe including packing the joints with rubber lubricant and fixing in to wall with wooden plugs, screws, holding clamps etc., complete Type 'B' - 3m

Supplying, fabricating and placing in position of Mild steel/Ribbed Tor steel grills for reinforcement for all RCC works in all floors including the cost of binding wire, bending, tying, etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers.

Manufacturing,Supplying and fixing in position of stainless steel hand rails for stair case using 50mm dia 304L Grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00 mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between . The vertical pipe has to be welded to the 100x100x6mm MS base plate encased in the base concrete.The rate is inclusive of the charges for cutting,bending,welding, grinding, polishing,conveyance, electrical charges,etc complete complying with relevant standard specification and as directed by the departmental officers.(The quality of all the materials should be got approved before use on works) Page 62 of SOR 23-24

Providing Precast Reinforced Cement Concrete Collar in CC 1:2:4 (One of cement two of M Sand and four of hard broken stone jelly) using 10mm size HBSJ of 23 cm inner dia and 25mm thickness including fabrication of grills, pre casting, moulding curing finishing, transporting and fixing in position in brick masonry wall in all floors etc. all complete complying with relevant standard specification and as directed by the departmental officers.

Water Supply Arrangement Supplying and fixing of 110mm dia PVC SWR pipe A Type for Rain water down fall pipe conforming to IS13592 with ISI mark and fittings conforming to IS 14735 , with necessary C I gratings, shoes, bends, offset ,clamp, teak wood plug, GI Bolts and Nuts, etc., of approved quality and including fixing C.I. gratings at the junction of parapet and floor or roof slab , including finishing etc., complete complying with relevant standard specifications. and as directed by the departmental officers.

Supplying, laying, fixing and jointing the following uPVC pipes as per ASTM D – 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials like Elbow, Tee reducers, Plug , union, bend, coupler, nipple etc., wherever required above ground level including the cost of Teflon tape, special clamps, GI Bolts and Nuts, nails, etc., fixing on wall to the proper gradient and alignment and redoing the chipped masonry after the pipes are laid etc., complying with relevant standard specifications & as directed by the departmental officers.

a) 50mm ASTM D Schedule 40 Threaded uPVC Pipes

b) 25mm ASTM D Schedule 40 Threaded uPVC Pipe

c) 20mm ASTM D Schedule 40 Threaded uPVC Pipe

Supplying, laying and fixing of 25 mm dia OD PN 16 poly propylene Random Copolymer (PP-R) pipes and specials of best approved quality for Hot water line using welding with required temperature fully concealed in walls including cost of pipes and specials, labour charges for laying, jointing, testing and redoing the dismantled portions with neat finish etc., all complete complying with relevant standard specification and as directed by the departmental officers .

Supplying and fixing of porcelain wash basin superior variety of approved quality of size 550mx400 mm (22" x 16") including cost and fixing of CI brackets, PVC waste pipe, CP tap, wheel/angle valve, pvc, connection, CP waste plug, with stainless steel chain etc., complete complying with relevant standard specifications in all respects as directed by the departmental officers. (The quality and brand of Wash basin and accessories shall be got approved from the Executive Engineer before supply)

Supplying and fixing of Health facuilt Stainless Steel body delux with one meter PVC tube with wall hook and C.P angel valve of Essco/ Jaquar fittings or equvalent and two way bicock of including cost of fittings labour for fixing etc, all complete complying with relevant standard specifications. and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use). PWD SR 19-20 P.No 54

Supplying and fixing of C.P. shower arm 190 mm long (light weight ) with wall flange and special shower with revolving joint Jaguar Fitting or equivalent including cost of fittings labour for fixing etc, all complete complying with relevant standard specifications. and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use). PWD SR 19-20 P.No 54

Supplying and fixing in position White / Colour Special Delux Model Glazed Cascade Type Parryware / Hindware / Equivalent Wall Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement forpacking, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection,

Supplying and fixing of PVC Nahani Trap not less than 75mm 4 way / 2 way (Superior variety) having minimum of water seal of 50mm confirm to relevant I.S. specifications with its latest amendments including resting on the bed of brick jelly concrete 1:5:10 (One of cement, five of M Sand & ten of 40 mm gauge brick jelly) etc., complete complying with relevant standard specification and as directed by the departmental officers (The PVC Nahani Trap should be got approved from the EE before use)

Supplying and fixing 150mm x 100mm size stone ware Gully trap with iron gratings over a bed of 150mm thick brick jelly concrete in CC 1:8:16 (one of cement, eight of M Sand and sixteen of broken brick jelly) using 40mm size brick jelly and brick masonry wall 115 mm thick using Second class chamber burnt ground mould bricks of size 9”x4-3/8”x2-3/4” (23x11.2x7cm) in cm 1:5 (One of cement and five of M Sand ) plastered with CM 1:3 (One of cement and three of M Sand) 12mm thick etc., complete complying with relevant standard specification and as directed by the departmental officers.

Supplying and fixing the following dia PVC (SWR) pipe type B class conforming to IS 13592and relevant specials including packing the joints with rubber lubricant fixing them into walls with necessary GI Bolts and Nuts with special clamp made of MS angle/Flat including cutting, bending (excluding the cost of MS angle/flat) holding wherever necessary and making good of the dismantled portion with necessary connections to sanitary fittings etc., complete complying with relevant standard specifications in all respects and as directed by the departmental officers.

a) 110 mm dia PVC SWR Pipe

b) 75 mm dia PVC SWR pipe

Supplying and fixing of 15 mm dia S.S Long body Bip cock with wall flange with Aerator of Essco jaguar fittings or equivalent including cost of fittings , labour for fixing etc, all complete complying with relevant standard specifications. and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Executive Engineer before use).PWD SR 19-20 P.No 55

Supplying and fixing of C.P Short body Bip cock with wall flange with Essco, jaguar fittings or equivalent including cost of fittings , labour for fixing etc, all complete complying with relevant standard specifications. and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use)BER.No 56/2017-18

Supplying and fixing of 15 mm dia S.S Elbow Action Tap with wall flange with Aerator of Essco jaguar fittings or equivalent including cost of fittings , labour for fixing etc, all complete complying with relevant standard specifications. and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Executive Engineer before use)PWD SR 19-20 P.No 55

Supplying and fixing of best approved quality C.P WASTE FOR SINK inculding cost of waste, labour charges for fixing etc., complete complying with relevant standard specification and as directed by the departmental officers BER.No 56/2017-18

Supplying and fixing of 20 mm dia CP Angle cock of Best Quality PWD SR 19-20 P.No 54

Supplying and fixing of C.P mixer 3 in 1 with provision of hand shower with 115mm long bend pipe and wall flange { with bush & button divertor fiting, with areator }like Jaquar Fitting or equivalent including cost of fittings, labour for fixing etc, all complete complying with relevant standard specifications and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use) PWD SR 19-20 P.No 53

Construction of Inspection chamber with brick jelly concrete 1:8:16 ( one of cement eight of M Sand and sixteen of hard broken jelly ) using 40mm gauge broken brickjelly 15cm thick for foundation and 23cm thick brick masonry in C.M. 1:5 ( One of cement and five of M Sand) using II nd class ground moulded Chamber burnt bricks of size 9”x4-3/8”x2-3/4” plastering with cement mortar 1:3 ( One of cement and three of M Sand) 12mm thick on both sides top and bottom including earth work excavation, supply and fixing of SFRC cover slab of required size including benching charnelling fixing cover slab in position curing finishing etc., complete in all respects.complying with relevant standard specification and as directed by the departmental officers.

60x60x60cms

60x60x75cms

60x60x90cms

Plain Cement concrete 1:2:4 ( One of cement, two of M Sand and four of hard broken stone jelly) for foundation and flooring using 20 mm size broken stone jelly inclusive of shoring, strutting, baling out water wherever necessary ramming, curing etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers.

Internal Electricals Wiring with 2 x 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990and with continuous earth by means of 1.5 sqmm copper insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI with suitable size MS box of 16 gauge thick concealed and covered with 3mm thick laminated hylem sheet for light point controlled by 5 amps Modular type switch including circuit mains cost of all materials, specials etc., all complete complying with relevant standard specifications and as directed by the departmental officers.

With Ceiling Rose

Light point with backlite Pattern Holder

Calling Bell bazzer

Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16g thick concealed and covered with 3mm thick laminated hylem sheet for Fan point controlled by 5 amps Modular type switch including circuit mains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers

Suppling and fixing of best approved quality Fan Box with hook inculding cost of all materials, labour charges for fixing etc., all complete complying with relevant standard specifications & as directed by the departmental officers in all floors.BER.No 46/2014-15

Wiring with 3x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS Box of 16 gauge thick concealed and covered with 3mm thick laminated hylem sheet for Staircase Light Point controlled by 5 amps Modular type two way switch including circuit mains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers.

Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16 gauge thick concealed and covered with 3mm thick laminated hylem sheet for 5 amps 5 pin plug Modular socket point at Switch Board Itself including circuit mains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers..

Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990and1.1.k.v. grade cable with continuous earth by means of 1.5 sq.mm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990and grade cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 1 No (each) 16g thick concealed and covered with 3mm thick laminated hylem sheet for 5 amps. 5 pin plug Modular socket point at convenient places including circuit mains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers..

Supplying and fixing 15amps 3 pin plug type Modular socket on a suitable MS box 16g thick concealed and covered with 3 mm thick laminated hylem sheet inclusive of all connections and cost of all materials all complete, complying with relevant standard specifications & as directed by the departmental officers.

Supplying and fixing 15amps Modular switch on a suitable MS box 16g thick concealed and covered with 3 mm thick laminated hylem sheet inclusive of all connections and cost of all materials all complete, complying with relevant standard specifications & as directed by the departmental officers.

Supplying and fixing 15amps 3 pin plug type Modular socket and switch on a suitable MS box 16g thick concealed and covered with 3 mm thick laminated hylem sheet inclusive of all connections and cost of all materials all complete, complying with relevant standard specifications & as directed by the departmental officers.

Supplying, fixing, connecting and commissioning of 32 AMPS Metal clad socket for Air Conditioner (Superior variety) combined with 32AMPS SP MCB in Manufactures mount box fixed flush with the wall including cost of material, necessary interconnection etc, switch on suitable angle Iron frame work with necessary earthing etc., all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Executive Engineer before use).

Supplying and fixing of water tight Bulk head fittings with One number of 11 Watts CFL BULB including necessary connections, cost of materials etc., all complete complying with relevant standard specifications & as directed by the departmental officers. ( The Brand/Quality of fittings and CFL Lamp has to be got approved by the EE before fixing) .

Supplying and fixing concealing of teak wood box of size 200 x 150 x 125mm concealed with 3mm thick hylem sheet for TV/Telephone Junction connection including necessary materials etc all complete in all respects complying with relevant standard specifications & as directed by the departmental officers.

Supplying laying and concealing of best approved quality 19 / 20 mm PVC pipes with necessary specials and other materials including run off 1no.fishwire (GI 22 G) for drawing cable for TV and telephone etc., all complete as directed by departmental officers.BER.No 46/2014-15

Supplying and concealing TV/ Telephone socket with top pin with suitable Teak wood box fully concealed and covered with 3mm thick laminated hylem sheet etc., all complete complying with relevant standard specifications & as directed by the departmental officers. BER.No 46/2014-15

Supplying and fixing of Box type Single Flouresent Fitting with copper choke and condencer, one number of 36 Watts Flouresent lamp etc.,complete with ISI mark, complying with relevant standard specifications & as directed by the departmental officers. ( The Brand/Quality of fittings and Lamp has to be got approved by the EE before fixing) .

Supplying and fixing of 40 amps earth leakage circult breaker / residual circuit breaker of FOUR POLE three phase ELCB of 30 amps sensitive 6 KA breaking capacity with ISI mark for incoming 2 Nos 6 amps B series miniar circuit breaker for outgoing 16 amps mininuar circuit breaker ISI mark power plug in suitable breaking capacity of MCB fixing on the 18 gauge MS box of size 300 x 375 x 650mm all concealed and covered with 3mm thick laminiated hilem with brase screws and all inter connection etc., complete complying with relevant standard specifications & as directed by the departmental officers (The brand and quality of ELCB should be got approved from the EE before use)

Supplying and laying of 8 SWG GI wire on wall / below ground levels with necessary ‘U’ Nails, earth work excavation and refilling etc... Including cost of all materials etc.. all complete complying with relevant standard specifications & as directed by the departmental officers..

Supplying and laying of 8 SWG copper wire on wall / below ground levels with necessary ‘U’ Nails, earth work excavation and refilling etc... Including cost of all materials etc.. all complete complying with relevant standard specifications & as directed by the departmental officers..

Providing Earthing station using pipe electrode as per IS 3043 using 2.5m of 40mm and 1.0 m of 20mm B-class GI pipe including earth work excavation, brick work in cement mortar and plastering and cost of funnel, GI nuts, bolts, washers, check nuts, GI bend, reducer and coupling, C.I. cover of 30x30cm and including charcoal of 40 kgs and salt 10 kg etc., all complete complying with relevant standard specifications & as directed by the departmental officers.

Supplying and fixing of Single type Street light Flouresent Fitting with copper choke, condencer, one number of 40 Watts Flouresent lamp, 20 mm dia GI pipe 'B' class with clamps, bolts etc.,complete with ISI mark, complying with relevant standard specifications & as directed by the departmental officers. ( The Brand/Quality of fittings and Lamp has to be got approved by the EE before fixing) .

Run of main with 2 wires of 2.5 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 19/20mm dia rigid PVC conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete and as directed by the departmental officers.

Run of main with 2 wires of 4 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 2.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 19/20mm dia rigid PVC conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete and as directed by the departmental officers.

Run of main with 4 wires of 6 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 2.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 32mm dia rigid PVC conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete and as directed by the departmental officers.

Supplying and fixing three phase distribution Board with 8 way/phase and 32 AMPs/per way with fuse and neutral link of Reputed Brand, on suitable TW, plank/ 12mm thick well varnished including necessary interconnection and earth connection cost of all materials etc all complete for inside flats. (The Brand/Model of the fitting has to be got approved by the Executive Engineer before fixing)

Supplying laying and connecting 31/2 25sqmm aluminium armoured UG cable with ISI mark of reputed brand including fixing in walls with necessary MS clamps, brass screws including cost of all materials redoing the dismantled portion, etc., all complete coplying with relevant standard specification and as directed by the Departmental Officers. (The quality and brand of UG cable should be got approved from Executive Engineer before use).

supplying and fixing 7 segements 3 phase distribution board with MCB 8way TPMCB sheet steel distribution board flush/surface type fitted with bus bar and netural link with single phase MCB outgoings and sepeate 4 way provision for accomadiating one no of 4 pile incoming MCB/Isolator and another sepearate 4 way provision for accommadating four no double pole ELCB /RCD and seperate provision for MCB ? ISolator for sub incomer in 3 segements with label holder and provision for taking up cable for size not less than 35 sqmm

Module type with IP 20 Protection 4 ways 3 phase DB No. of ways incomer MCB / Isolator - 4 No. of ways incomer ELCB / RCD - 4 No. of outgoings ways - 12

SRI PATHY ASSOCIATES PRIVATE LIMITED (BID ID -1036216)