Electrification work of 02 Nos Court Room for Additional commissioner in Campus of Commissioner office of Meerut

wiring point for light with 1.5sq. Mm FRLSH PVC insulated multistrand copper conductor cabelin PVC conduit concealed in wall complete with 1.5 sq -mm FRLSH PVC multistrand single core copper conductor as earth wire drawn inside the condut with GP box Modular type switch and celling rose / Batten holder complete in all respect as directed in ENC including matching colour wash complete in all respect

wiring point for fan/fresh air fan with 1.5sq. Mm FRLSH PVC insulated multistrand copper conductor cabelin PVC conduit concealed in wall complete with 1.5 sq -mm FRLSH PVC multistrand single core copper conductor as earth wire drawn inside the condut with GP box Modular type switch and celling rose complete in all respect as directed in ENC including matching colour wash complete in all respect

wiring point for Call bell with 1.5sq. Mm FRLSH PVC insulated multistrand copper conductor cabelin PVC conduit concealed in wall complete with 1.5 sq -mm FRLSH PVC multistrand single core copper conductor as earth wire drawn inside the condut with GP box Modular type bell push switch and two pin socket complete in all respect as directed in ENC including matching colour wash complete in all respect

Supply & Fixing 5/6A modular switch and socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (On existing switch board)

S/F of suitable size GI Box with modular plate and cover in front on surface or in recess, including providing and fixing two nos. 3 pin 5/6 A modular socket outlet and two nos. 5/6 A modular switch, connections etc. as required.

S/F of suitable size GI Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 A modular socket and 15/16A modular switch, connections etc. as required.

Supply and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/recessed PVC conduit as required size 01 No. x 1.5sq.mm (For Invertor wiring)

S/F of 125A FP MCCB 36 KA @ CAT- A

S/F of 63A 4 Pole MCB 10KA @ CAT- A

S/ f of 6A-32A SP MCB 10 KA @ CAT- A

S/ Burrying 600x600x3mm GI plate vertically for with its top at least 3 meter below ground level with 20 mm dia G.I. Pipe and funnel for watering and two earthing lead with 30 cm sq cast iron frame with hinged cover measonary housing alternate layer of charcol/coke and salt at least 150 mm thick around complete in all respect.

S/F OF 25x 5 mm GI strip for earthing on G.I clamps on surface complete in all respect

S/f surface mounting 4 way TPN DB with additional metal door without MCB complete in all respect @ cat-A

S/f of surface/Flush mounting 4 way VTPN DB with additional metal door without MCCB 200A complete in all respect.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground levelover a cushionof 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge,complete in allrespect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 95 Sq mm x3.5 core

Supply and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required. Size 95 sq.mm x 3.5C

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground levelover a cushionof 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer- incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 70 sq. mmx3.5 core.

Supply and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required. Size 70 sq.mm x 3.5C

Installation for Fresh Air fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Up to 450 mm Sweep.

Supplying and fixing call bell/buzzer suitable for single phase, 230 V complete as required.

Supply and wiring of submain with 2 Nox6sq-mm FRLSH PVC Insulated 1100 V Grade single core Multi strand copper conductor cabel in 25 mm dia heavy duty PVC conduit Conceled in wall complete with 1 NO 4 Sq mm as a earth copper wire drawn conduit

Same as above but for submain 2Nox4Sq.mm with 1 No. 2.5 sq.mm conductor cable as earth wire drawn in concieled conduit including matching colour wash etc complete in all respect

Same as above but for submain 2Nox2.5sq.mm with 1 No. 1.5 sq.mm conductor cable as earth wire drawn in concieled conduit including matching colour wash etc complete in all respect

Same as above but for submain 4NoX 6 Sq.mm with 2 No. 6 sq.mm conductor cable as earth wire drawn in concieled conduit including matching color wash etc complete in all respect

Same as above but for submain 4NoX 16Sq.mm with 2 No. 6 sq.mm conductor cable as earth wire drawn in concieled conduit including matching color wash etc complete in all respect

Supply and fixing of G.P. Modular switch box for 1 / 2 Module of approved make made up of 1.0 mm thick ISI Marked G.P.sheet including adjestable Nakka and holes plugged with PVC Nylon Caps . Two or more holes for pipe entry of 25.4 mm on upper and lower sides of the box. Holes should be semi-shuttered type and fitted with heavy brass Earth Piller duly screwed & brand name should be embossed. Box flushed in wall including cutting of brick work, fixing it to the level with cement sand mortar, including matching colour wash with s/o all materials, labour and T&P required for proper completion of work as directed at site by the Engineer in charge. (for TV Dish socket)

S/F ofT,V, socket point modular complete in all respect.

Supply and drawing co-axial TV cable RG-6 grade, 0.7mm. Solid copper conductor PE insulated, shielded with fire tinned copper braid and procted with PVC seath in the existing pipe complete in all respect.

S&F of 200 A. 415 V Heavy Duty TPN main switch complete on angle iron frame complete in all respect.

S&F of 200 A Four pole. 415 V moulded case type on load Heavy Duty change over switch on angle iron frame complete in all respect.

S/f DP sheet steel enclosure on surface/recess along with 25/32 A 240V "C" curve DP MCB complete with connections, testing and comissioning etc. as required.

SITC of 90w LED street light fixure, Powder coated pressure die cast aluminium body (System lumen efficacy>135 lm/watt). Driver efficiency>85% Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range-5 OC to 50 OC, Internal Surge protection of 5 KV L,N,E, as per IEC 61000-4-5, Driver efficiency >85@, THD <10% as per IEC 61000-3-2, P.F.>.95, IP -66, 1K-10, CRI >70, under voltage and over voltage protection, EMI_EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement. suitable fo fit in up to 65mm dia pipe, life time (LED, Dirver & electrical circuitary) of minimum 50000 Burning Hours with 70% of initial Lumen maintenance till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000'K/4000'k/5700'/6500'K (As per ANSI Bin), SDCM <5, maximum power consumption should be not more than the specification rating and Fixture shall be of relevant BIS standard complete in all respect.

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, flicker should be below 5 %), life time (LED, Driver electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing. complete in all respect

Supply and laying of 1800mm x900mm x 12mm thick chequered rubber matting of tested quality.

Supply and fixing ofg double LED light wall bracket 3 to 6 watt on matching M.D.F.E.G Boartd base etc. complete in all respect. CAT-AAA.

SITC of LED Batten light (System lumen efficacy >135 lm/Watt) of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P.F.≥0.95, IP20, CRI >80, Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated

Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire with driver set confirming to IP 65 and above Protection . complete in all respect. CAT-AAA S/f of Bulk Head 10W

SITC of LED Down lighter (SMD Type) (System lumen efficacy >135lm/Watt) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range - 5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K/4000°K /5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect.

Supply and fixing of 3 Watt to 6 Watt LED Mirror light luminaire Confirming to IP 66 Protection complete in all respect. CAT-AAA

SITC of Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation, Testing and Commissioning ofceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required.

Panel Fabrication out of 2.0/1.6mm thick CRCA sheet steel, painted or powder coated paint of shade as per the direction of Engineer incharge after sheet treatment process of sheet steel. The Bus bar of panel shall be electrical grade High conductive Aluminium alloy of appropriate cross section per rating. which shall be mounted on proper interval to ensure the bear short Circuit of 50 KA for panels having ACB as incomer & 36 KA for having MCCB incomers. Panel shall be constructed in fully Segregated compartment Design of Each feeder. There shall be metering compartment for Incomer Metering and outgoing Metering provided in switchgear Feeder also. All incomer Feeders shall be with multifunction Metering along with phase indicating Lights and associated components such as CT, control MCB Terminal Block etc. all above shall be provided as accommodated all measuring unit shall be Digital type & all including lights shall be LED type. Wiring done from 1100V Grade PVC insulated copper flexible wire. All ACB electricity operated Draw-out type with microprocessor based O/L, S/C type of Breaking/with stand capacity (ICU/ICs/icw) 50KA or more all have Thermal Magnetic/Microprocessor with O/L, S/C & E/F along with required Spreaders & Extended Rotary Handle with pad capacity of Breaking capacity (ICU/ICS) 35 KA or more all MCB shall be 10KA 'C' Curve. complete in all respect Cubical Panel. CAT-B Incoming 200A MCCB-01 No. Outgoing 100 Amp MCCB 02 Nos." etc.

S/o of Fresh air fan 300mm sweep size Light duty complete in all respect

Supply and fixing of LED Bulb 10 watt.

S/F of fire extinguisher CO2 type 4.5 Kg capacity complete in all respect.

S/F of fire extinguisher ABC type 4.0 Kg capacity complete in all respect.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. for 100 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required.for 80 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type-A) with blank Gunmetal/Stainless Steel cap and chain as required.

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforming to IS 636 as required gunmetal.

SITC of Hose Box of 18 SWG M.S Sheet with glass front door to accommodate 2 nos. RRL Hose & 1 nos. SS Branch Pipe with nozzel.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required.100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required.80 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, Gi bolts, nuts, washers etc.as required. 100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, Gi bolts, nuts, washers etc.as required.80 mm dia

SITC of Air Cushion Tank assembly 200 mm dia. 1.5m long with Air Release Valve pressure gauge & accessories.

Terrace PVC Tank having Capacity of 5000 Liter x 2 Nos. = 10000 Ltr.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required. 450 LPM Terrace Pump.

SITC of Automatic Panel for Terrace Pump suitable for 5HP. Complete in all respects.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required. 4 way.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

SITC of Pressure Gauge. Complete in all respect.

SITC of MS Support for pipe fitted with anchor bolt including painting.

SITC of 25 mm Air Rlease Valve. Complete in all respect.

S/L of Aluminium conductor PVC Insulated sheated cable 1100 volt grade as per PWd Specification. For 10 Sqmm 4 core

Supply & making in termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminum conductor cable of 1.1 KV grade. For 10 Sqmm 4 core

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 6 Zone.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of heat detector operating at 54°C/57°C with rate of rise cum fixed tempreature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

SITC of Manual Call point Break Glass type housed in MS sheet, including connection.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supply and wiring of submain with 3 no.1.5sq mm pvc insulated 1100 volt grade single core copper conductor cable in existing conduit on surface/recess complete in all respect.

Supply and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.