Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹1.9 LAccepted-Finance NO 42 PERIYAN NAGAR THANGAMAPURIPATTINAM METTUR DAM 636 402 | METTUR DAM | SALEM | TAMIL NADU | 636402 | 1 | Accepted-Finance satisfied |
Tender Value
₹2.6 L
EMD Value
₹2,600
Closing Date
14 May 2020, 2:00 pmClosed
Superintending Engineer /Mechanical-I/MTPS-I
Office of the Superintending Engineer / Mechanical -I Mettur Thermal Power Station- I Mettur Dam-636406
MTPS I Mill Plant A C Plant Unit II Annual overhaul Air Washer System Epoxy painting the blower 2A and 2B etc
2020_EB_162887_1
SE / M-I / MTPS-I / MP / OT. 31 / 2020-21
Open Tender
Power/Energy Projects/Products
Works
20 days
Mettur Thermal Power Station-I / Mettur Dam
As per the Tender Specification
4 documents required · 4 mandatory
₹0
₹2,600
Yes
18 May 2020
30 Apr 2020
15 May 2020
30 Apr 2020
14 May 2020
30 Apr 2020
Amount
Charges for dismantling a casing cover of the blower 2A & 2B for painting and reassembling after completion of painting works.
Charges for scratching and cleaning, then painting of epoxy zinc chromate premier one coat and epoxy smoke grey painting two coat for structures, spray room tank pipes, eliminator frame, water strainer structure, AWS Blowers 2A & 2B, dampers and ducts (Inclusive of paint & Thinner).
Charges for dismantling the damaged portion of existing discharged air washer duct by gas cutting bolts & angles and fabrication of the discharged duct by cutting the GI sheet as required size and the angles of size 45 x 45 x 6mm as required size erection of the air washer duct and renewing the hanging support. (Angle will be supplied by Board, 1mm thick GI Sheet & 12mm thick MS rod under contractor scope)
Overhaul of AW Blowers 2A & 2B: a) Charges for removing Blower pulley (blower 2A & 2B) from the shaft by heating and then re-fixing the new pulley / replacing pulley into the shaft.
b) Charges for removing the damaged bearing, cleaning the bearing (drive end & Non-drive end) and replacing the new Plummer block and bearing and then greasing (blower 2A & 2B).
c) Charges for balancing, motor positioning on the bed, checking alignment and providing belt and checking belt tension with the motor .and commissioning (blower 2A & 2B).
Charges for de coupling the AWCW Pumps 2B & 2C removing of pump, Overhaul the pumps and alignment checking & commissioning.
Charges for dismantling the Water spray nipples and nozzles from the pipe line and scratching & cleaning and then re fixing in the pipe line.
Charges for flushing the spray system pipe line and devolution to central stores lead and lift etc., ( Lorry will be supplied by board ).
stage.html
html • 0.03 MB
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .