SPECIAL REPAIR TO OR COOK HOUSE BLDG NO P-379 OF INF BDE CAMP, SPECIAL REPAIR TO BLDG NO P-527 OF SIKH REGT AND ADDN ALTN OF EXCHANGE ROOM AT COMN COMPLEX OF INF BDE SIG COY IN ZONE-III AREA UNDER GE(S) JAIPUR AT JAIPUR MILITARY STATION

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and in soft /loose soil etc complete all as specified and directed.

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil etc complete all as specified and directed

M&L for sand filling under floor or in foundations including watering and consolidation complete all as specified and directed. Note:- Punned thickness of sand shall be measured and paid.

Removal of excavated materials (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed.

M&L for Nominal mix 1 : 1½ : 3 type A-1 using 20 mm graded stone aggregate as in chajjas and similar work complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, copings, bed plate, plinth courses, roof kerbs or mud stops rounded or chamfered on edges including necessary form work complete all as specified and directed.

M&L for providing precast cement concrete louvres and jallies 25 mm thick (measured solid) including all mouldings but excluding frame in cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregates and set in cement mortar 1:4 complete all as specified and directed.

M&L for providing precast cement concrete louvres and jallies 35 mm thick (measured solid) including all mouldings but excluding frame in cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregates and set in cement mortar 1:4 complete all as specified and directed.

M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall,beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for drilling suitable holes in reinforced cement concrete with power driven drill machine to a minimum depth of 10D (D-Dia of Bar in mm) in RCC beams, lintels, columns and slabs to introduce new steel bars including cleaning the holes by air blowers prior to fixing the steel bars in position using Lokfix E77 a two-component epoxy anchoring material, supplied in 3:1 ratio having compressive Strength (EN196) >122 N/mm2, Flexural Strength (EN196) >66 N/mm2, E Modulus (EN ISO 527-2) 6300 N/mm2. or of equivalent make but excluding the cost of reinforcement, complete all as per direction of Engineer-In- Charge. Anchoring chemical shall comply with ETA 21/0354, ETA 21/0518 for anchoring bars for 10mm dia

M&L for applying bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surfaces after applying anticorrosive paint over cleaned rusted steel surface including demolition old RCC surfaces (chajjas, fins, beams , borders etc and applying 30mm thick polymer modified mortar in CM 1:3 including mixing of polymer latex additives for repair of Chajjas fins, border etc complete all as specified and directed. Note :- (i) cleaning of rusted part of steel and applying anticorrosive paint over it. (ii) Qty of ploymer to be used 15% by weight of the cement or as per manufacturer instruction. (iii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iv) To achieve required thickness repeat this step after 24 hrs as required. (v) Keep the surfaces moist using water fog for 5 to 7 days etc complete all as specified and as directed. (vi) Rate shall be inclusive of all necessary scaffolding for building of height upto two storey. Make :- (i) The epoxy bonding agent shall be Krishna / Dr Fixit / MC Bauchemie / M/s Cemistik / Sika or equivalent as approved by GE. (ii) Polymer latex addictive shall be of Sika / Fosroc / Dr Fixit or equivalent as approved by GE.

M&L for brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L Brick work using old size bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and directed.

M&L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good in Brick walls/RCC cutting not exc 10 cm girth complete all as specified and directed.

Cutting holes in stone wall not exc half brick built in cement mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

M&L for brick protection cover to the under ground cable (with old size sub class 'B' bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10 mm all as specified and directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) for fair finished flat surface of concrete complete all as specified and directed

Form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface complete all as specified and directed.

Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished concrete surfaces complete all as specified and directed.

S&F second class hard wood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed.

S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Taking down chowkats or frames n.exc 1.5 Sqm each with shutters ( with out taking off shutters from the frames) including making good of disturbed portion except space for holdfast complete all as specified and directed.

Taking down chowkats or frames exc. 1.5 sqm but n.exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) including making good of disturbed portion except space for holdfast complete all as specified and directed.

Taking down shutters of any description exc. 1.00 Sqm but n.exc. 2.00 Sqm each complete all as specified and directed.

S & F for solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified and directed

S & F Factory made Solid PVC Moulded door shutter with particle board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S & F Factory made Solid PVC Moulded door shutter with Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S & F Solid PVC wall Lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S &F 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

S&F factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories, for area exceeding 2.00 sqm each complete all as specified and directed Note:- The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.

S&F factory made uPVC white colour casement door with top hung ventilator with 3D and SS friction (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

M&L in repair for 18 mm thick WPC (Wood Polymer Composite) panel with suitable pins, screws and adhessive in cabinets body, shutters and shelves etc. complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed.

S&F brass handle of 100mm size, cast type, polished bright complete all as specified and as directed.

S&F aluminium handles cast type anodised of 150 mm size complete all as specified and directed.

S&F in repair 100 mm Mortice latch with two levers (vertical type), brass body complete all as specified and directed.

S&F in repair harrison rail (curtain rail) mild steel chromium plated with fixing brackets ,stops, rollers etc complete as all specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 150 mm complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repair 25 mm bore dia mild steel coloured PVC laminated curtain rod fancy type with fixing brackets ,stops, rollers etc complete as all specified and directed.

S & F auto close hinges, stainless steel, bright finish or electrogalvanised fixed.complete all as specified and as directed

S&F anodised aluminium alloy curtain rails with fixing brackets ,stops, rollers etc complete as all specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed.

S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, hold fasts, wall ties, hooks for hanging fans ,cleats for securing purlins to wood trusses or rafters and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5 cm long and 5 to 10 mm dia of shank complete all as specified and directed.

M&L for mild Steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel section in roof trusses (framed), trussed, purlins, crane gantries,rail and fastenings and heavy bracket framing (beam, tee, angle,channel or flat sections) including distance pieces, cleat etc of grade Fe 410-W (Gde E-250) quality B complete all as specified and directed.

S&F rolled mild steel section in framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified in SSR part I clause No 10.24, erected in position and securing runners with holdfasts and bracketscomplete all as specified and directed.

Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specified and directed.

M&L for powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

M&L in repair for powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed. Note-Glass and other filling material in panels shall be measured and paid seperately

S&F in repair powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed. Note-Glass and other filling material in panels shall be measured and paid seperately.

S&F for powder coated (thickness of powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. Note-Glass and other filling material in panels shall be measured and paid seperately

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for carried out water roof treatment as under :- (a) Complete removal of existing roof treatement and disposed off the rubbish outside the defence land. (b) Preparation of dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with including WPC @ 3% weight of cement or as per manufactururer instruction. (c) All visible cracks to be opened up in V shape cleaned properly with wire brush washed and filled with cracks filling compound for cracks upto 5mm width / depth of cracks. (d) Cracks of more than 5mm width / depth are filled with URP cement grouting by injecting through nozzles till refusal by authorised applicator of manufacturer, carefully by following manufacture instruction. The size and spacing of nozzles shall be as per manufacturer instruction or as directed by Engg-in-Charge. (e) M&L rendering 10mm thick in cement mortar (1:3) on concrete surfaces to receive water proofing treatment finished even and smooth complete all as specified. (f) Necessary gurantee for 5 years shall be submitted by the contractor. Make :- Cement Grout : Dr. Fixit (Fixit Pidicrete URP Model:301) or equivalent in Fosroc / Choksey chemicals / Sika / Berger (HS Super Grout) or equivalent as approved.

M&L for fibre reinforced, UV resistant elastomeric liquid applied water proof coating over cementitious surfaces, highly elastic and hairline crack bridging capacity (elongation 250-350%), non toxic, VOC complaint water based coated in three layers first being priming coat, forming complete tihckness as metioned by OEM and complete all as specified and directed. Make:- Asian / Berger / Sika or equivalent.

S&F providing / fabricating /assembleing and fixing anodized aluminium fixed partion using Jindal make, medium weight aluminium section as follow :- (i) Horizontal members - size 63.50 x 38.10 mm @ 0.75kg/m c/c spacing shall not exceed 90cm. (ii) Vertical members - size 63.50 x 38.10 mm @ 0.75kg/m c/c spacing shall not be more than 90cm. (iii) Bottom portion - 3 inch height portion, including prelaminated board 12mm thick and all necessary clips, rubber beading, aluminium beading and fixing to the adjoing / existing wall/portion beading etc. (iv) Top portion - 5mm thick plain glass / grounded glass with all necessary fittings / fixture etc, complete all as specified and directed. Note:- Section given above are of Make Jindal, the contractor may use similar section of other Make as mentioned in Appx 'B' of PS.

Providing and fixing suspended false ceiling (make Armstong ANF AH 95 or equivalenet as approved) extra microperforation size of 600 x 600 x 15 mm Ceiling Tiles over suspension metal system (MICRO LOOK) designer grid (15 mm grid 8mm return) SILHOUETTE X L 15 MM (NOMINAL) of make Armstorng or equivalent make including necessary hanging system arrangement which is required to be made from existing RCC roof /stone /slab /AC sheet of existing ceiling complete all as specified and directed.

M&L for Machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing on treads of step and landing of stair including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing on treads of step and landing of stair including screed bed 20 mm thick in CM 1:6 complete all as specified and directed.

M&L for granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 complete all as specified and directed.

M&L for 50 mm thick Cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring 40 mm thick surface finished even and smooth with out using extra cement complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm / 450X 350X 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm / 450X 350X 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 15 mm thick in CM 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed or bedding layer 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed or bedding layer 15 mm thick in CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:3 as in ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering on fair faces of brick work or concrete surface of wall 15 mm thick in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed

M&L for rendering on fair faces of brick work or concrete surface of wall 15 mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed

M&L for 15 mm thick screed bed or bedding layer in CM 1:6 surface finished fair and even for laying floor finishes complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M & L for two coats of cement based paint on new plastered surface of walls over a coat of alkali resistant priming paint including preparation of surface complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old surface of wall of any description and applying two coats of oil bound distemper over and including 1 mm thick wall putty complete all as specified and directed.

M&L for preparation of new surface of wall of any description and applying two coats of oil bound distemper over 1 mm thick wall putty all as specified and directed.

M&L for preparation of old decorated surfaces of wall with complete removal of existing treatment and apply two coats of cement based paint over a coat of alkali resistant priming paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and apply two coat of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceilings and apply two coat of white wash on old decorated surfaces complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling by brooming or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots making good using putty by filling depression wherever required and apply two coat of white wash complete all as specified and directed

M&L for preparation of new plastered surfaces of ceiling and applying two coat of oil bound distemper over a coat of alkali resisting priming paint complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling by complete removal of existing treatment and applying two coat of oil bound distemper over a coat of alkali resisting priming paint complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls by complete removal of existing treatment and applying two coat of acrylic emulsion exterior graded weather proof paint over a coat of primer complete all as specified and directed.

M&L for preparation of new surface of walls of any description with a coat of wall putty and applying two coats of acrylic emulsion exterior grade weather proof paint over a coat of primer complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F figured glass 4 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone,concrete or brick surrounds, glazed with putty of fixed with beads complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

Dismantling of AC/PVC water tank and S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position complete all as specified and directed

Dismantling of AC/PVC water tank and S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position complete all as specified and directed.

S&F in repair bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore dia of pipe complete all as specified and directed.

S&F in repair for 15mm bore dia of pipe pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair for 15mm bore dia of pipe pillar taps cast copper alloy, with capstan head chromium plated fancy type screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F for 15mm bore dia of pipe brass CP mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

S&F in repair stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions for 20 mm bore dia of pipe complete all as specified and directed.

S&F in repair stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F in repair ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule of 15 mm bore dia of pipe complete all as specified and directed.

S&F in repair waste fittings, brass, chromium plated 32mm dia for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S& F in repair Angle stop valve for 15 mm bore dia of pipe of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 90gms) complete all as specified and directed.

S&F grating doom 100 mm dia of PTMT (minimum weight 25 grams) complete all as specified and directed.

S&F in repair grating doom 100 mm dia of PTMT (minimum weight 25 grams) complete all as specified and directed.

S&F towel rail 450 mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 170 gms) complete all as specified and directed.

S&F in repair towel rail 450 mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 170 gms) complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S & F cast iron soil, waste and vent 75 mm bore of pipes (sand cast) in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F cast iron soil, waste and vent 100 mm bore of pipes (sand cast) in any length with or without ears, with cement joints, fixed to wall complete all as specified and directed.

M&L PVC (SWR) floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed

M&L PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and directed

M&L for SGSW gully trap 150 x 150 mm square or round mouthed type 'P' complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

M&L Wash down water closet vitreous china white pedestal pattern with 'P' or 'S' trap including connecting to outgoing drain pipe & to flushing pipe excluding flushing cistern and flush pipe complete all as specified and directed.

S&F in repair Water closet vitreous china squatting pan, orissa pattern 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) and including provision of lime concrete bedding ,'P' or 'S' trap 100 mm bore , flushing pipe ,anti-syphonage pipe and connection etc and making good to floor complete all as specified and directed.

M&L in repair for Vitreous China urinals, bowl type flat back size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement etc complete all as specified and directed.

S&F in repair PVC, 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, inlet, ball valve, float and handle etc complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm size with or without swivel joint complete all as specified and directed.

M&L for wash basins, Vitreous China, white, flat back, size 630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets & cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair white rimless Single piece- EWC with UF soft close slim seat cover, Hinges, fixing accessories and accessories set and cistern fittings, S trap including fixing as per manufacturer instructions complete all as specified and as directed. Make : Jaquar CAT Part No OPS-WHT-15853S300UF / Roca Cat Part No. RS34273700H / Kholer Cat part No. K-77739T-SL-0 / Cera Cat Part No. S1013245 .

M&L for supplying, laying, connecting and testing in trenches / under floors / roads or on walls for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm 4 core complete all as specified and directed. Note:- Excavation,earth work,sand,brick and protection pipe shall be measured and paid seperately.

M&L for supplying, laying, connecting and testing in trenches / under floors / roads or on walls for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 4 core complete all as specified and directed. Note:- Excavation,earth work,sand,brick and protection pipe shall be measured and paid seperately.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for point wiring complete with 1.5 Sqmm single core (Phase - Red, Neutral - Black) PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in and including concealed PVC conduit 20 mm dia medium grade with all accessories ISI marked, including MS sunken box for mounting fitting like switches, sockets fan regulators etc. including 1.5 sqmm single core (Green colour) PVC insulated unsheathed copper earth continuty conductor FRLS cable 1100 V grade as continuous earth wire for one light / fan / bell point controlled by one, one way switch. Note :- (i) The make of modular plate shall be of the same brand as per Switch / Socket accessories. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sqmm (Green), concealed in wall and drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS sunken boxes for mounting switches, sockets, fan regulator as required for one 3 pin socket outlet 5 Amps on the same board with other switches, complete all as specified and as directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sqmm (Green), concealed in wall and drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken boxes for mounting switches, sockets, fan regulator as required for 3 pin 5 Amps socket outlet on independent board, complete all as specified and directed. Note :- (i) The make of modular plate shall be of the same brand as per Switch / Socket accessories. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken boxes for mounting switches, sockets, fan regulator as required for 3 pin 15 Amps socket outlet on independent board, complete all as specified and directed. Note :- (i) The make of modular plate shall be of the same brand as per Switch / Socket accessories. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 Sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken boxes for mounting switches, sockets, fan regulator as required for 3 Pin 15 Amps socket outlet on independent board, complete all as specified and directed. Note :- (i) The make of modular plate shall be of the same brand as per Switch / Socket accessories. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

S&F LED lights fitting 1x20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

M&L lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F switch piano, flush type, 6 amps single pole, one way, complete all as specified and directed.

S&F switch piano, flush type, single pole, one way, 16 Amp complete all as specified and directed.

S&F Modular Switch one way 6 A, 1 module complete all as specified and directed.

S&F modular switch 1 way 16A, 1 module complete all as specified and directed.

S & F Modular Socket, 6A - 2/3 pin combined, 2 module complete all as specified and directed.

S&F modular socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F socket outlet 3 pin, 16 Amp, flush type complete all as specified and directed.

S&F socket outlet 2 in 1,3 pin, 6 Amp complete all as specified and directed.

S&F sheet metal enclosure with socket plug top and MCBs single pole and neutral enclosure with a two pin and earth plug and socket with one single pole MCB of capacity 20 Amps complete all as directed.

S&F sheet metal enclosure factory fabricated for MCB distribution board SPN double door type concealed in wall 240 Volt 12 way IP-42 protection with 200 amp rated bus bar complete all as specified and directed.

S&F sheet metal enclosure factory fabricated for MCB distribution board TPN double door type concealed in wall 415 volt 4 way IP-42 protection with 200 amp rated bus bar complete all as specified and directed.

S&F sheet metal enclosure factory fabricated for MCB distribution board TPN double door type concealed in wall 415 volt 8 way IP-42 protection with 200 amp rated bus bar complete all as specified and directed.

S&F ceiling rose 3 phase, PVC / polycarbonate, isolated body complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI wire 4 mm dia as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints including excavation and earth work, GI pipe light grade 15mm bore for protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:3:6) type B-1 using 20mm graded stone aggregate for chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1 using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm bore GI Pipe medium grade for watering complete all as shown in electrical plate No 3 of SSR Part-I(2009) and connected to earth test point including testing complete all as specified and directed. Note :- 1. PCC Chammer shall be constructed atleast 1.5 metre away form the earth electrode of the earth pit and pipe for watering shall be provided in slanting manner. 2. GI wire and protection pipe upto 7.5 meter from the earth plate electrode is deemed to be included in quoted rate. 3. Excavation for earthing to be done manually and Earth resistance below 3 Ohm should be obtained after measurement for every pit.

Fixing only exhaust fan after minor repair like oiling, greasing etc and connecting up including provision of cable from ceiling rose / connector to fan complete all as specified and directed.

Taking down fan / exhaust fan any type, sealing cable end, dismantling blades and removing fan and blades to MES store complete all as specified and directed.

S&F ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete all as specified and directed.

S&F exhaust fan, steel body AC single phase, 230V of size 450 mm sweep heavy duty with, blades, and frame and louvers complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep with minimum air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. of 100 watt capacity complete all as specified and directed.

M&L for sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated unsheathed FRLS copper cable 1100 V grade with multistranded copper conductor ISI marked drawn through and including PVC rigid conduit / casing capping not less than 20mm and conduit accessories fixed on surface of wall / celing etc including provision of 1 Run of 6 Sqmm PVC insulated unsheathed FRLS cable with multistranded copper conductor as earth continuity complete all as specified and directed. Note : 02 Run of 06 Sqmm copper wire and 01 Run of 06 Sqmm copper earth wire along with PVC conduct shall be measured as one unit.

M&L for sub main wiring complete with 4 Runs of 6 Sqmm single core PVC insulated unsheathed FRLS copper cable 1100 V grade with multistranded copper conductor ISI marked drawn through and including PVC rigid conduit / casing capping not less than 25mm and conduit accessories fixed on surface of wall / celing etc including provision of 1 Run of 6 Sqmm PVC insulated unsheathed FRLS cable with multi-stranded copper conductor as earth continuity complete all as specified and directed. Note : 04 Run of 06 Sqmm copper wire and 01 Run of 06 Sqmm copper earth wire along with PVC conduct shall be measured as one unit.

S&F electric water heater (Geyser), storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. complete all as specified and directed. Note:- Connection with geyser inlet and outlet with 15mm bore GI pipe including PVC pipe is included in the quoted rate

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 06 to 32 AMP, complete with connection testing and commissioning all as specified and directed.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN and 40 to 63 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

S&F 415V 10KA 'B' curve miniature circuit breaker (MCB) of TPN / FP and 40 to 100 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single Pole and 06 to 32 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

Supply and install hi wall split units indoor / outdoor with cooling and heating function complete with cordless remote control unit with in built air ioniser and Plasma filter for better indoor air quality with minimum 04 star rating and of 2.0 TR capacity complete all as specified and directed.

Taking down and dismantling ceiling fan including accessories of any type or make, safely and re-fixing after oiling, greasing and servicing in serviceable condition including provision of cable from ceiling rose or connector to fan including painting of fan by one coat of synthetic enamel paint of in white / off white colour by spraying including filling cavities with filler, after cleaning all dust etc. including writing MES No. on each fan complete all as specified and directed.

S&F LED fixtures 20 Watt with extruded polycarbonate, environmental friendly, slim design with decorative and caps, high performance diffuser for soft & glare free light, minimum lumen output 1900 lm with efficacy 110 lm/w, driver with high voltage protection upto 380 V AC & surge protection upto 2.5 KV, CCT(K)-6500, LM 80 tested high brightness LED technology complete all as specified and directed.

S&F LED mirror light adjustable type 12 watt 230 volt single phase 6500K complete all as specified and directed.

S&F LED surface light adjustable type 18 watt, 230 volt single phase 6500K complete all as specified and directed.

Disconnecting and taking down Geyser of any make/ type safely and refixing the same after minor repair like cleaning, tightening of loose component etc and painting with two coat of white synthetic enamel paint complete all as specified and directed.

S&F electrical chimney of 90 cm size, suction capacity not less than 11550 cubic meter/hr and air outlet size not less than 150 mm motion sensor touch control, turbo speed option, dual side touch control, blower type- metallic, speed 9, energy efficient BLDC motor complete all as specified and directed.

Supply and fix, testing and commissioning of Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5.0 KVA with time delay relay 2 to 3 minutes over load protection complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortor in floor, apron etc complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

Demolition of cement concrete un-reinforced in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of AC corrugated / semi corrugated or translucent sheet as in roof coverings complete all as specified and directed.

UNIVERSAL INFRAPROJECT PVT LTD (BID ID -3312746)

M/S ROHIT CONSTRUCTION (BID ID -3309794)

MSR INFRATECH (BID ID -3309743)