SPECIAL REPAIR TO BLDG NO P-23 (01 to 04) Type C Md Accn at RP Colony UNDER GE (WEST) AGRA

Amount

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles complete all as specified and directed.

M&L for Brickwork with sub class ‘B’ bricks, old size, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for Brickwork with sub class ‘B’ bricks, old size, straight or curved on plan exc 6m mean radius built in CM 1:6 ,except bricks,complete all as specified and directed.Note:- Bricks obtained from item no 1 shall be used after cleaning.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness (below or above ground level) complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed.

M&L for 25mm thick PCC(1:2:4) type B0 using 12.5mm graded aggregate as in sub base of floor etc

M&L for 75mm thick PCC (1:4:8) type D2 using 40mm graded aggregate as in sub base of floor etc complete all as specified and as directed

M&L light shade vertified ceramic tiles 10 mm thick (square/rectangular) area of each tile not exc. 0.36Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed.

M&L vertified ceramic tiles 10 mm thick (square/rectangular) area of each tile not exc. 0.36Sqm as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in vertical surfaces such as skirting ,dado,s and riser to stepsetc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:3 for laying complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350x 250x 7mm/450 x 300 x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:3 on other than fair faces of brick wall finished rough to fix tiles complete all as specified and directed.

M&L for mirror polished machine cut Kota stone in stair case tread flooring 20-25mm thick laid over 20mm thick screed bed in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. (Note : only one stone piece on one tread with nosing one side)

M&L for mirror polished machine cut Kota stone slab in stair case riser 20-25mm thick on vertical surfaces over 10mm thick cement plaster in (1:3) such as risers, skirting etc. jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and taking down existing skirting complete all as specified and directed. (Note : only one stone piece on one riser)

M&L for Green Marble work (Baroda green) 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types complete all as specified and as directed.

M&L 18/20mm thick black granite (of any type) work (table rubbed and polished) in steps jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of stone including rounding and moulding of edge and making hole for cooking gas pipe complete all as specified and as directed.

Boring holes through cooking platform lining for pipes ,etc n'exc 50mm dia and making good complete all as spd and dir by Engr-in-charge.

M&L for 5cm thick Sand stone slabs in sun-shades, chajjas,shelves, cills, landings,cover stones, templates, etc.n exc. 2m in length,punched dressed on face and along exposed edges,self faced on other side and set and pointed cement mortar 1:4. complete

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors and including 20mm thick screed bed in CM (1:6) of approved colour and pointing with grey cement and pigment complete all as specified and directed.

Demolition of cement concrete (reinforced) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work

M&L for 75mm thick cement concrete type C-2 (1:3:6) (using 40 mm graded stone aggregate ) as in plinth protection and path finished even and smooth without using extra cement. Joints 20mm /10mm wide will be provided every 1.5m, at corners and along wall shall be made and filled with sealing compound grade ‘A. The joints between external wall and plinth protection shall also be filled with sealing compound grade ‘A’ complete all as specified and directed

Taking down cement or cement lime plaster on walls any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

M&L for for 10 mm thick ready mix plastering on external surface of brick or concrete surface work with mixing WPC@3% by wt of cement including finishing the surface even and smooth complete as specified and directed. (Note-Integral water proofing compound shall be measured and paid separately under respective item)

Supply only integral water proofing compound (WPC) complete all as specified and directed.

M&L for washed stone grit plaster on exterior walls in two layers 12mm cement plaster 1:4 (1 Cement : 4 Coarse sand) furrowing the under layer with scratching tool ,applying cement slurry on the under layer @3kg of cement per square meter,top layer 15mm cement plaster 1:1/2:2 (1 Cement : 1/2 Coarse sand : stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing ,the top layer with brushes and water to expose the stone chipping complete all as specified.

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens,nailed to the layer incl removal of wooden battens, repairs to edges of panels and finishing the groove complete as per specification and direction

M&L for 10 mm thick ready mix plastering on internal surface of brick or concrete surfaces complete all as per manufacturers specification suface finished even and fair complete all as specified and directed.

M&L for preparation of new surface of walls (external surfaces) and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) innormal pattern, as per manufactures instructions etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion white or tinted with roller, over complete all as specified and directed.

M&L for 1mm thick wall care putty on wall

M&L gunniting to RCC works in column, beams, chhajja, slabs, landing, balconies etc by removing loose concrete including plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50microns thick to rusted steel reinforcement after removing/ cleaning all rust by sand / grit blasting and supply and fixing welded steel wire mesh 75 mm x 75 mm with 3 mm dia steel wire as facies/drops and similar works etc and expoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sika. Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2.5Kg /sqcm and applying 25mm thick layers of gunniting in cement mortar (1:2) using ordinary port land cement of 43 grade over wherever required complete all as specified. Note:- (i) After placing the additionnal reinforcement all concrete surface shall be throughly scrubbing with brushed washed with water and allow dry and plaster complete all as specified. (ii) Work to be carried out as in patches as directed (iii) Rate for scaffolding ,15mm thick plaster in CM 1:4 and TMT bars (where applicable) deemed to be included in quoated rate. (iv) preparation of surface and applying two coat of OBD/exterior emulsion with one coat of primer over 1mm thick wall care putty,deemed to be included in this item. (v) work to be carried out upto 12 m height

M&L for 20 mm thick ready mix plastering on roof surfaces of brick or concrete surfaces including providing & mixing 2% water proofing compound of wt of ready mix plaster complete all as per manufacturers specification suface finished even and fair complete all as specified and directed.

M&L for preparation of old/new plastered concrete surfaces and applying three coats of smart care damp proof ultra of asian paint or similar with roller all as per manufacturers instruction and as directed

Taking down old steel/wooden windows/ventilators with holdfast & making good surface to match with the existing and S&F for Colour coated galvanized steel (Eco-4000 Series or similar) windows/ventilator fabricated from roll formed sections made of (Base steel as per IS 513"D" quality, galvanized as per IS 277 with finc of 120 gms/ sqm) with total coated thickness of 0.60mm. Sections should be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mmx50mm, section for mullion should be of 72mm x50mm, section for shutter frame should be of 47mmx20mm, section for fixed glass bead should be of 12mmx12mm and section for fly mesh shoulld be of 40mmx20mm. Each glazed shutter and mesh shutter shoulld be provided with SS pivot hinges-1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm plain float glass. Mesh shutter should be provided with stainless steel 32 guage fly mesh of 304 grade with 144 holes per sq.In. Window/ventilator should be provided with grill made of 10mm sq MS bars welded to at 150mm centre to centre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws. NOTE: The quoted rate shall be deemed to be included the following:- (i)All type of fitting required to operate window/ventilator is deemed to be inclusive in the rate quoted. (ii)Making good of jambs in CM (1:4) and applying OBD in two coats including with putty complete

Taking down existing sunken portion treatment by demolition of old concrete and carry out the sunken treatment as in following steps given below and procedure as per Appendix'A' of particular specifications.(a) S & F of drainage spout GI pipe 40mm dia bore light grade upto outside or outer wall ( Apprx 450mm to 600mm long).(b) M & L for PCC 1:1.5:3 type A-0 (using 12.50mm graded stone agg) 50mm thick laid in slope towards drainage out spout pipe mixed with waterproofing chemical as per manufacturer instructions of MAKE: FOSROC/SIKA/PEDILITE/STP Khurra 150mmx150mm (min) at appropriate location for free flow (of leaked water if any) towards drainage spouts shall be provided integrally while laying PCC. Fixing of spout shall be done with same PCC as in this item.(c) M & L for 18mm thick cement plaster in CM 1:3 on verticalfaces mixed with water proofing chemical of Make: 301 Pidicrete URP of Dr Fixit or other techno commercially equvalent Make of : SIKA/Pedilite/FOSROC/STP.(d) Items No40(C) shall be executed while concrete is green as per item No 40(c) above and proper curing and ponding test shall be done before laying dfrainage water supply pipes upto the entire satisfaction of Engineer-In-Charge.(e) Applying two coats of SIKA TOP seal 107 of SIKA or other techno commercially Equivalent Make of FOSROC/Pidilite/Dr Fixit/STP on vertical as well as horizontal surface.(f) Drainage and water supply pipe if required and test for leakage /sanitary pipes and shall be laid to slope and a clear gap underneath the pipes shall be made avbailable by providing suitable cement concrete block.(g) M & L PCC 1:5:10 type E-2 using 10-40mm graded stone aggregate as reqd depth at site over and including 150mm thick 20mm single sized stone agg to provide a filter media.(h) M&L PCC 25mm thick 1:2:4 type B-0 using 12.5 mm grade stone aggregate as level course.(j) M&L for 7 to 8 mm thick non skid ceramic coloured joint less tiles (aquare/rectangur) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc laid jointing in neat cement slurr and pointed filled with epoxy chemical Make :- SIKA/FOSROC/PIDILITE/Dr Fixit/STP mixed with pigment to match with shade of tiles over and including 15mm thick screed bed in CM(1:6) complete all as specified and directed.(k) Note for item : (i) Waterproofing treatment shall be undertaken alongwith laying of drainage pipe/sanitary pipes/drainage spout etc. (ii) The work shall be carried out as per the direction of Engineer-In-Charge. (iii) The sunken treatment work shall only be carried out after written approval of Engineer in charge for leakage/seapage of water/ sanitary pipes. (iv) Cost of drainage spout shall deemed to be included in the item however sanitary pipe, water ipe line if required shall be paid separately under respective items. (v) Laying of chemicl required for varios applications shall be as per manufacturer instructions. (vi) Plan area shall only be measured and paid.

Taking up or down steel and connections including cleaning for refixing or removal to store 15mm bore complete all as specified and directed

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm bore complete all as specified and directed

Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth etc brick wall complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing complete all as specified and directed.

S&F in repair 10 Ltrs capacity, PVC valveless, syphonic action type, low level flushing cistern, white, with inlet, ball valve, float and handle complete with all internal accessories and fixed to wall, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC with and including 600 mm long PVC connection with 02 Nos PTMT nuts and rubber washer and making good to disturbed surfaces of wall or floor complete all as specified and directed.

S&F in repair stainless steel sink with drainage board made out of stainless steel 1.00mm thick sheet for kitchen with plugs, washers and waste, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting unions to pipe over all size 915mmx460mm with bowl size 410mmx330mmx160mm complete all as specified & directed.

S&F in repair min 32 mm dia Semi Rigid PVC waste pipe for for sink and wash basin with length not less than 700 mm complete all as specified & directed

S&F in repair CP stop valves/angle valve 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed .

S & F in repair health faucet with 15mm dia 1 mtr long flexible tube and wall hook chromium plated complete all as specified and directed.

S&F Cabinate Mirror PTMT complete all as specified and directed.

S & F in repair 15 mm bore pillar tap fancy type , cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe all as specified and directed.

S&F in repair bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, anti syphonage and providing cement concrete bedding complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (Pedestal pattern), white with 'P' or 'S' trap incl seat and cover (excluding fluxing cistern and flush pipe) complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back size 550x400 mm including two Nos angle iron brackets including,,complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair Waste coupling of CP (half or full threaded) of 32mm bore suitable for wash hand basin complete all as specified and directed.

S&F in repair Waste coupling of CP (half or full threaded) of 40mm bore suitable for Sink complete all as specified and directed.

S&F in repair brass chromium plated shower roses with or without swivel joints 125mm size with CP long shank arm including fixing to steel pipe or union complete all as specified and as directed.

S&F in repair Chromium plated 20mm dia, D type,60cm long towel rail with towel racks fixed with & including CP brass screws & wooden/plastic cleats (min. weight 190gms) complete all as specified and directed.

S&F in repair stainless steel grating with openable flap 100 mm dia complete all as specified and directed.

S&F in repair brass CP wall/sink mixer/WHB mixer for mixing Hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed.

S&F in repair PTMT soap dish fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms)

S&F in position rotational moulded polyethylene water storage tanks 500 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position with and dismatling of exisitng tank complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 1000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position with and dismatling of exisitng tank complete all as specified and directed.

S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F steel tank cover with zinc coating, dia of cover 500 mm and height 150mm of cut spherical shape and gas welded of spikes 2mm dia and 50mm length at 50mm c/c both bay in zig zag motion with ms hinges, hasp and staple fixed to existing PVC water water storage tank of any capacity including dismantling of old pvc water tank cover complete all as specified and as directed.

S&F plate rack with racks and guard bars made out of stainless steel minimum 1mm thick, over all min size 750mm X 600X250mm and assembled with using brass nuts, bolts and washers complete all as specified and as directed.

S&F sheet glass corner self (of 3 tier )assembly consisting of 5.5mm thick sheet glass self 15cm radius with chromium plated bracket guard and rail and fixed with CP screws and wood cleats with wall complete all as specified and directed.

S&F toilet paper holder of chromium plated fixed to walls with chromium plated (CP) brass screws complete

S & F in repair 25 mm dia SS drapery rods fancy type with brackets ,stops, rollers ,side knobs etc complete all as specified and directed.

Demolition and breaking up rain water pipe (PVC, AC, or re-inforced concrete ) of sice 100mm coplete all as specified and directed.

S&F PVC SWR pipes 110mm bore single socketed in any length with rubber ging joints fixed to wall complete all as spd and directed.

Fixing only PVC SWR pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius all as specified

S & F 110 mm bore PVC (SWR) cowl of any radius complete all as specified & directed.

S&F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays. Including bolts & nuts & securing ends of stays to wall or roof for 100 mm bore pipe complete all as specified and directed.

S&F in repair min 100mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints and suitable clamp fixed to wall complete all as specified and directed.

S&F 110 mm bore PVC (SWR) single T with access door of any radius complete all as specified & directed.

S&F 110 mm bore PVC (SWR) single Y with access door of any radius complete all as specified & directed.

S & F 110 mm bore PVC (SWR) cowl of any radius complete all as specified & directed.

S & F in repair 100mm dia cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete

S & F in repairs 100mm dia of cast iron floor trap, plain with grating incl jointing with solvent cement concrete type B-1 (1:2:4complete all as specified and directed complete all as specified and directed.

S & F in repairs 125/110 mm dia of PVC (SWR) Gully trap, plain with grating incl jointing with solvent cement complete all as specified and directed.

M&L welding in repairs not exc 2.5 cm in length and not exc 6mm thick complete all as specified and directed.

M&L welding in repairs exc 2.5 cm but not exc 5.0 cm in length and not exc 6mm thick complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S&F framed work as in doors or gates or chhajja of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening conforming to Fe-290 (Gd E-165) complete all as specified and directed.

S&F of MS angle iron bracket (design as directed) for door/windows chajja frame work with 04 nos MS fasteners of 16mm dia and 100mm long including MS rivets (for one set) drilling holes and making good fixed anchoring inside wall and top of roof complete all as specified and directed (weight of fasteners incl with MS angle frame arrengments).

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etc of grade Fe-410-W (Gde E-250 quality B) complete all as specified and directed..

M&L Hand rails, 50mm dia hollow steel tube or other steel section hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, alusters, nosing to steps ncluding embeding in concrete and screwing etc. wind ties for roof including securing oltsposts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 Sqm including making good of jambs with cement mortar 1:4 etc complete all as specified and directed.

Taking down chowkhats or frames shutter (without taking off shutters from the frames) n exc 1.5 Sqm including making good of jambs with cement mortar 1:4 etc complete all as specified and directed.

Taking down shutters of any description n exc 1 Sqm each complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specification and shown in drg in SSR Part -II 2020 complete all as specified and as directed

S&F factory made solid panel PVC door moulded shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain cover PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specification and drg shown in SSR Part -II 2020 complete all as specified and as directed

Taking down shutters of any description n exc 1 Sqm each complete all as specified and directed.

S&F 18mm thick WPC (Wood Polymer Composite) of minimum density 600kg/cum both side plain for cupboard shutter including fixing of 0.8mm thick acrylic laminates as edge banding in matching colour over all exposed edge complete incl SS handles,hinges and all connected assesories all as specified and as directed.

S&F 18mm thick WPC (Wood Polymer Composite) of minimum density 600kg/cum one side prelaminates and other side plain for kitchen cabinet shutter including fixing of 0.8mm thick acrylic laminates as edge banding in matching colour over all exposed edge etc incl SS handles,hinges and all connected assesories complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F 30mm thick brand factory made wire mesh solid WPC door shutter With Both side decorative laminated with .12-24 Microne pvc film of consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per S:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings. complete all as specified and directed

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of min size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F MS hold fast and similar article conforming to Fe-290 Gde-E-165-0 or Fe-310-o all as spfd.

M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregated as in cill, step and for inserting hold fast of doors and windows all as specified and directed.

S&F 200 mm long stainless steel finished barrel tower bolt of extruded section complete all as specified and as directed

S&F 100 mm long stainless steel finished barrel tower bolt of extruded section complete all as specified and as directed

S&F 150 mm long stainless steel finished handle fabricated type complete all as specified and as directed

S&F 100 mm long stainless steel finished handle fabricated type complete all as specified and as directed

S&F stainless steel sliding door bolt, 250 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed

S&F stainless steel butt hinges, medium weight, cold rolled, 100mm size complete all as specified and as directed

S&F stainless steel finished butt hinges cold rolled medium weight of size 75 mm complete all as specified and as directed

S&F magnetic catcher of approved quality in cub board and kitchen cabinet including fixing with necessary screws double strips (horizontal type ) complete all as specified and directed.

M&L for brass Locks for cupboard, of grade I, size 65mm 2 levers complete all as specified and directed.

S&F Floor door stopper 150 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

S & F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as spd and dir.

S&F 125mm long aluminium anodised Hasp and Staple, safety type including bolt to hinge plate and fixed with screws complete all as specified and directed.

M & L for applying one coat of synthetic enamel paint including preparation of old Iron surface of any discription not otherwise discribed over 10 cm width or girth, complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10 cm width or girth, not otherwise described complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of distemper oil emulsion white or tinted with roller,incl repair of holes and cracks complete all as specified and directed.

M&L for writing letters or figures (Block, Roman,Italic or Indian) ,n exc 30cm high Complete all as specified & directed.

M&L for treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials to MES stores for segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all asspecified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 2.5 Sqmm copper conductor (Multi-standard) PVC insulated and unsheathed electric cable 1100 volts in and including PVC Conduit of suitable size with all fittings/ accessories in concealed and including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm ( multi-stranded) copper conductor single core( Green co lour) cable as continuous earth wire connected to common earth dolly including 50 mm deep box made of 2nd class hard board of required size and shape etc covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point independent controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 123 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 123 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 123 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing switch piano flush button single pole one way 5 Amps complete all as specified and as directed by the Engineer-in-Charge.

One bell/buzzer pointcontrolled by one push button on the same board withother switches or independent with cables1.5 sq.mm size

Supply and fixing socket outlet multipurpose 2 pin and 3 pin, 5 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5 Amp and 15 Amp, flush type complete all as specified and as directed by Engr-in-charge

Supply and fix in repair Bell, Ding Dong AC. 230 volts,single pole complete all as specified and as directed by Engr-in-charge

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB complete all as specified and as directed by Engr-in-charge

M&L for in replacement of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 4.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

Supply & fix surface/wall mounting LED batten 20 watt luminaire having extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver with mounting accessories complete with wall/ ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix in replacement MCB DB sheet metal enclosure factory fabricated double door SPN 8 way with 200 amps rated bus bar 240 volts complete all as specified and directed.

Supply & fix in replacement MCB SPN, 40 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply & fix in replacement MCB SP, 5 TO 32 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply and fix in replacement MCB DB 4 way sheet metal enclosure triple pole and neutral 415 volts with 200 standard bus bar of suitable size and common neutral link and earth bar all enclosed on standard steel sheet flush mouting type double door factory fabricated complete without MCB but with enclosue blank plate complete all as specified and directed .

Supply and fix in replacement MCCB 4 pole 100 to 125 Amp Icu 16 Kilo Amp and Ics 100% of Icu with adjustable 70% to 100% and thermal magnetic release suitable for fixing in DB.

M & L earthing complete in replacement with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanised steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe upto 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Looose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1 .

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 16 Amps

Cuttings chases, pinning in making good to facing on brick walls & pointing in CM 1:3 for concealed water tubing cutting n exc 10 cm grith including making good to dismantled surfaces with existing finishes (like tiling etc) all as specified and as directed.

S&F 15mm Tubes, 'Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.

S&F 15mm bore angle stop valve of cast copper alloy chromium plated high pressure screwed for iron pipe and fixed all as specified

Supply and fixing Bip tap 15mm dia ,cast copper alloy chromium plated fency type with crutch or butter fly handle screwed down for iron pipe or brass ferrule and fixed complete.Make zoloto/Prayag

Supply & fixing PVC connection 15mm bore length not less than 300mm long with both ends PTMT nuts complete all as directed .

Taking down old Fan any type and deposite to E/M Store yard and Supply and fixing ceiling fans complete with blades, down rods, and remote control suitable for BLDC Fan and accessories, 230 V, 1400 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply & fix exhaust fans AC single phase 230/ 240 V of size 380 mm sweep with louver including cutting hole plastering etc for fixing exhaust fan

Supply and fix electric water heater, storage type steel body with fiber flash coated inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, etc.

C P Singh and Co (BID ID -3294037)

M/s Krishna Construction Company (BID ID -3291512)

M/S DEVENDRA KUMAR GUPTA (BID ID -3293778)

CREATIVE CONSTRUCTION (BID ID -3294040)

M/S RISHI RAJ AGRAWAL (BID ID -3294070)

M/s Himgiri construction (BID ID -3294050)

Captainkomalchaharconstructions (BID ID -3294013)

M/s United Engineers (BID ID -3293250)

N.K. ENTERPRISES (BID ID -3293889)

M/S OMKAR SINGH YADAV (BID ID -3293968)

M/s Om Infracon (BID ID -3293773)

M/s Navansh Engineers & Consultants (BID ID -3293749)

Gupta Automobiles (BID ID -3293912)

Bidder Name

M/s Navansh Engineers & Consultants